蓝色发光材料DPVBi掺杂DCJTB发光性质的研究

对蓝光材料DPVBi掺杂红光染料DCJTB的发光性质进行了研究。首先研究了DPVBi掺杂不同质量浓度DCJTB的光致发光，当掺杂质量浓度为0.1％时，光致发光得到白光(色度x=0．36，y=0．34)。基于光致发光的实验结果，以DPVBi掺杂不同质量浓度DCJTB作发光层，制备了结构为ITO／CuPc／NPB／DPVBi：DCJTB/Alq3／LiF／Al的器件，当掺杂质量浓度为0．08％时器件实现了白色发光(色度为x=0．25，y=0．32)。研究了该白光器件的电致发光性质，白光器件在14V时达到最高亮度7822cd／m^2。在20mA／cm^2电流密度驱动下的亮度为489cd/m^2，最大流明效率为1．75lm／W。     

一种白光有机电致发光器件的制备

通过对器件结构的优化设计，提高了白光电致发光器件中蓝光成分的发光效率，从而得到了一种较为理想的有机白光电致发光器件。驱动电压为5V时，电流密度J=0．5mA／cm^2，器件的效率达到最大，流明效率为1．92 lm／W，此时器件的发光亮度接近20cd／m^2。色坐标为(x=O．317，y=0．328)。非常接近白光等能点．是色度很好的白光。并且在很大范围内，色度随器件的驱动电压或电流变化不大，当驱动电压变化至15V时。f=232mA／cm^2，色坐标变化至(x=0．338，y=O．353)。在电压为22V时，器件的亮度达到最大，为17 000cd／m^2。此外器件结构相对简单。器件制备的可重复性得到很大程度的改善。     

高色纯度有机白光电致发光器件

介绍了具有高色纯度的多层有机白光器件,器件发光的色坐标为x=0．33,y=0．34,非常接近白光等能点,是色度很好的白光器件。而且在8～14V很大的范围内,发光色度随器件的驱动电压或电流的变化不大,基本稳定在x=0．33,y=0．34。在电压为19V时,器件的亮度达到了最大9735cd／m^2,在电压为9V时,器件的效率达到了最大4．5cd／A。     

利用有机层间互相掺杂提高有机电致发光器件的效率

提高器件的发光效率是实现有机电致发光器件实用化的一个关键因素。通过对器件结构和制作工艺的优化设计，将有机电致发光器件的各个功能层进行互相掺杂，在层间形成互掺过渡层达到平衡载流子的注入，使得注入的电子和空穴有效地限制在互掺的有源区内，增加了载流子相遇复合的几率，进而提高器件的发光效率。器件的最大电流效率在外加电压10．5V时达到7．9cd／A，最大发光亮度在35V时达到49000cd／m^2。和一般掺杂器件相比效率提高2倍以上。同时有机层间的互相掺杂也在一定程度上消除了层问的界面，减少了有机层问的缺陷，与没有过渡层的器件相比，器件老化性能有了明显改善。     

以蓝色发光材料DPVBi为基质的白色发光器件

白色有机发光器件是实现彩色平板显示的重要方案之一。利用蓝色发光材料DPVBi[4，4′—(2，2—苯乙烯基)—1，1′—联苯]掺杂红光染料DCJTB[4—氰甲烯基—2—叔丁基—6—(1，1，7，7—四甲基久洛尼定基—9—烯炔基—4H—吡喃)]作发光层制备了白色发光器件。研究了DPVBi掺杂不同浓度IDCJTB薄膜的光致发光性质，根据光致发光结果，制备了以DPVBi掺杂不同浓度DCJTB作发光层的电致发光器件，其结构为ITO／GuPc／NPB／DPVBi：DCJTB／Alq3／LiF／Al。当DCJTB质量分数为0．0008时，器件实现了白色发光(色度x=0．25，y=0．32)，电致发光和光致发光的掺杂比例基本相符，表明器件的白色发光主要是由基质DPVBi向掺杂剂DCJTB的能量传递产生的。研究还发现：白色器件随电压升高，光谱中蓝色成分相对于红色成分的比例略有增加，文章对此现象进行了分析。该白光器件在14V时达到最高亮度7822cd／cm^2，在20mA／cm^2电流密度下的亮度为-489cd／cm^2，最大流明效率为1．75lm／W。     

柔性衬底白色有机电致发光器件的制备及其性能

采用以ITO为导电层的柔性透明PET基片作为衬底,以2-(2-羟基苯基)苯并噻唑螯合锌(Zn(BTZ),)作为发光层制备出结构为PET／ITO／PVK：TPD／Zn(BTZ)2／Al明亮的近白色柔性有机小分子电致发光器件。发光的色坐标值为x=0．242,y=0．359,在25V的直流电压驱动下,亮度为1000cd／m^2,量子效率达到了0．30％。并进一步在Zn(BTZ)2中掺入橙红色染料Rubrene,制成PET／ITO／PVK：TPD／Zn(BTZ)2：Rubrene／Al结构器件。实现了纯白色发光(色坐标值：x=0．339,y=0．339),非常接近于白色等能点,驱动电压为25V时器件的亮度达1200cd／m^2,且量子效率达0．35％。最后对器件的发光性能及机理进行了深入的研究和探讨。     

稳定的蓝色及白色有机薄膜电致发光器件

报道了一种稳定的蓝色和白色有机薄膜电致发光器件,蓝色器件最大亮度为7526cd／m^2,最大效率1．451m／W,半亮度寿命1035h(初始亮度l00cd／m^2)。白色器件的最大亮度为14850cd／m^2,最大效率2．881m／W,色度x=0．31,y=0．38,且色度不随电流增大而变化,半亮度寿命为2860h(初始亮度100cd／m^2)。     

色纯度改进的苯乙烯衍生物高效蓝色有机电致发光器件

以苯乙烯衍生物(amino-substituted distyryl arylene derivative，BCzVB)掺杂的4，4’-双(9-咔唑基)-1，1’-联苯(4，4’-N，N’-dicarbazole-biphyenyl，CBP)为发光层，制备了结构为ITO(indium tin oxide)／TPD(N，N’-diphenyl-N，N’-bis(3-methylphenyl)-1，1’biphenyl-4，4’diamine)／CBP：BCzVB／Alq3[tris-(8-hydroxy-quinolinato)aluminum)／Liq(8-hydroxy-quinolinato)lithium]／Al的电致发光器件。这里TPD、Alq3分别为空穴传输层和电子传输层，CBP：BCzVB为发光层，Liq为电子注入层。器件最高亮度为8500cd／m^2，效率为3．5cd／A(量子效率为2．6％)，器件色坐标[Commission Internationale de l’Eclairage(CIE)CO-ordinates]为x=0．15，y=0．16，与纯BCzVB作发光层的器件相比，器件的发光色纯度和效率得到大幅提高。光致发光与电致发光对比分析表明器件的发光主要来自能量传递和陷阱俘获机制，但陷阱俘获机制起了主导作用。     

联苯乙烯类蓝色发光材料DPVBi的合成及发光性质研究

合成了联苯乙烯类蓝色有机发光材料DPVBi[4，4′-二(2，2-二苯乙烯基)-1，l′-联苯]，用^1H-NMR，IR，元素分析等方法对其结构进行了表征。以DPVBi作发光层制备了电致发光器件，其结构为：ITO／CuPc／NPB／DPVBi/Alq3／LiF／Al，研究了器件的电致发光性质。器件最高亮度达4 373cd/cm^2，最大流明效率为1．24 lm／w，在20mA／cm^2电流密度驱动下的亮度为434cd／cm^2，CIE色坐标为x=0．15，y=0．16，器件的蓝色发光具有较好的色纯度。重点对器件发光色度的稳定性进行了研究，结果表明，随电流密度(4～4 000mA／cm^2)的变化，器件色度具有很好的稳定性。     

利用电子传输层掺杂改善有机发光器件的效率

利用BCP掺杂到电子传输层Alq中,在掺杂层中阻挡了空穴的迁移,调整了空穴和电子的平衡,将激子有效地限制在发光层中发光,从而增加有机电致发光器件的效率.器件的最大电流效率在外加电压9 V时达到4.1 cd/A(掺杂浓度8%时),与一般未掺杂器件相比效率提高了2倍多.同时也减少空穴到达阴极,而减少发光淬灭.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.