Simultaneous capillary GC-MS determination of triazines and amides in water

Summary A simultaneous capillary Gas Chromatographic-Mass Spectrometric (GC-MS) method is described for the determination of thirteen pesticides belonging to the triazine and amide families in water. The sample is extracted in liquid-liquid mode (dichloromethane) and then the determination of the residues is carried out by capillary gas chromatography with mass spectrometric detection in the Selected-Ion Monitoring mode (SIM). The average recoveries of spiked compounds are in the 78.4–135.4% range between the relative low level (0.100 g L^–1) and the relative high level (10.0 g L^–1). The limits of detection (LOD) are in the 0.009–0.128 g L^–1 range.     

Gas chromatographic analysis of methiocarb and its metabolites in soil and rice

Summary A new method to determine the amount of methiocarb and its two metabolites, the sulfoxide and sulfone in soil and rice plant is described. The method consists of extraction of samples with acetone, filtration, separation of methiocarb and its metabolites through a Florisil column, and gas chromatographic determination. Since the degradation of methiocarb to 3,5-dimethyl-4-methylthiophenol (DMMP) is commonly observed during GC analysis, methiocarb was converted to DMMP via chemical hydrolysis after column chromatography. Reasonable recoveries for routine analysis were obtained and the limit of quantitation (LOQ) with GC/FPD were 0.5, 2 and 2 ng for DMMP sulfoxide and sulfone, with a signal to noise ratio of 4. In all rice samples, no detectable residues were found, however DMMP and methiocarb sulfoxide were found in some straw samples. In field soil samples, no sulfone was detected in all samples and methiocarb showed typical degradation curves with a half life of 8 days after treatment. A five-fold longer half life was observed in indoor studies.     

Continuous-flow microextraction and gas chromatographic-mass spectrometric determination of polycyclic aromatic hydrocarbon compounds in water

A new method of the determination polycyclic aromatic hydrocarbons (PAHs) in water samples was developed by continuous-flow microextraction (CFME) coupled with gas chromatography-mass spectrometry (GC-MS). In this experiment, 15 mL sample solution with no salt-added was flowed at the rate of 1.0 mL min⁻¹ through 3 μL benzene as extraction solvent. Under the optimal extraction conditions, the developed method was found to yield a linear calibration curve in the concentration range from 0.05 to 15 ng mL⁻¹. Furthermore, the accuracy and repeatability of the method were good by calculating from water samples spiked at known concentrations of PAHs, and the recovery of optimal method was satisfactory. The results showed that CFME was an efficient preconcentration method for extraction of PAHs from spiked water samples.     

Gas chromatographic determination of 29 organic acids in foodstuffs after continuous solid-phase extraction

A simple and expeditious method based on continuous solid-phase extraction and gas chromatography-mass spectrometry (GC-MS) was reported for the direct determination of 29 organic acids in food and beverages. A sorbent column packed with 80 mg of LiChrolut EN-Supelclean ENVI-18 (1:1) was employed for extraction and clean-up purposes. After elution with 200 μL of methanol, the methanolic extract was directly injected into the GC-MS without prior derivatization. The method provided good linearity (0.5-1000 μg kg⁻¹) and fairly good precision for all compounds (RSD lower than 6.2%). The recoveries of the organic acids from diluted samples that were spiked at three different concentrations (10, 40 and 100 μg kg⁻¹) ranged from 93 to 98%. The applicability of the method was demonstrated by analyzing the target compounds in a wide variety of foodstuffs including beer, wine, fruit juice, soy sauce, soya milk and honey samples.     

Capillary gas chromatographic determination of amitrole in water with alkali flame ionization detection

Summary A capillary gas-liquid chromatographic method with alkali flame ionization detection is described for the determination of amitrole in water samples. The method is based on the acetylation of amitrole with acetic anhydride. The limit of detection is ca. 0.1 μg per litre water. The average recovery in groundwater is 97%.     

Validation of an enzyme-linked immunosorbent assay (ELISA) for the determination of 4-nonylphenol and octylphenol in surface water samples by LC-ESI-MS

4-Nonylphenol (NP) and octylphenol (OP) were measured by direct ELISA in both laboratory-fortified and surface water samples collected monthly from 10 rivers. In this procedure, samples were concentrated by solid phase extraction (SPE) using Lichrolut RP-18 sorbent with good recoveries obtained for both LC-MS and ELISA, giving a low level of detection (LOD) at the range of low μg L⁻¹ and good reproducibility. Analysis of 40 surface water samples demonstrated that the ELISA may be a useful screening tool for the determination of the alkylphenols in surface water matrices. The concentration of NP and OP in surface waters ranged from 0.11 to 6.58 μg L⁻¹. A good correlation of results obtained by ELISA and LC-MS within the concentration range of 0.08-6.86 μg L⁻¹ was found in the river samples [R² = 0.924, n = 39]. The influence of various factors on assay determination was also discussed.     

Tetraaqua-bis(3-hydroxy-4-nitrobenzoato) Co(II) and Ni(II) complexes and diaqua-bis(2-hydroxy-4-methoxybenzoato) Zn(II) complex: crystal structure and thorough metal-coordination investigation

Reactions of Co(II) and Ni(II) salts with the monosodium salt of 3-hydroxy-4-nitrobenzoic acid (3) in aqueous solution resulted in isomorphous covalent complexes 3C and 3D, of centrosymmetric geometries. In similar conditions, 2-hydroxy-4-methoxybenzoic acid (5) led to the covalent Zn(II) complex 5A, exhibiting a marked dissymmetric geometry. The present crystallographic data with structural data for a series of closely related metal complexes previously reported allow a tentative rationalization of the solid-state architecture of such complexes. The dissymmetry in 5A was interpreted on the basis of a mixed (monodentate and bidentate) metal-ligation mode and a pyramidal coordination at the metal.     

Headspace gas chromatographic determination of aromatic hydrocarbons in natural and waste water

Summary The possibilities of using headspace analysis of aromatic hydrocarbon traces in aqueous solutions with changing values of the partition coefficients are discussed. A variant of headspace analysis of the simplest aromatic hydrocarbon in natural and waste water is described. It involves two-step gaseous extraction of a sample in vessels of varying volume before and after the equilibrium phase is replaced with a pure gas (air or nitrogen). This method permits to analyse 5–50 ml water samples with benzene and toluene contents varying from the ppb to the ppm range within an error not exceeding 155. The analysis time is about 1.5 h. The presence of non-volatile organic or mineral substances does not influence the determination. This method is unsuitable to heterogeneous systems (aqueous oil emulsions): before carrying out the analysis for the hydrocarbon content these systems have to be homogenized first.Presented at the Scientific Seminar on Headspace Gas Chromatography organized in cooperation with the Perkin-Elmer Corporation (Norwalk, CO, USA) in Leningrad, December 4–5, 1979.     

Dispersive liquid-liquid microextraction followed by gas chromatography-mass spectrometry for the determination of nitro musks in surface water and wastewater samples

A new, simple, fast and high sensitive analytical method based on dispersive liquid-liquid microextraction (DLLME) followed by gas chromatography-mass spectrometry (GC-MS) for the simultaneous determination of nitro musks in surface water and wastewater samples is presented. Different parameters, such as the nature and volume of both the extraction and disperser solvents and the ionic strength and pH of the aqueous donor phase, were optimized. Under the selected conditions (injection of a mixture of 1 mL of acetone as disperser solvent and 50 μL of chloroform as extraction solvent, no salt addition and no pH adjustment) the figures of merit of the proposed DLLME-GC-MS method were evaluated. High enrichment factors, ranging between 230 and 314 depending on the target analyte, were achieved, which redound to limits of detection in the ng L⁻¹ range (i.e., 4-33 ng L⁻¹). The relative standard deviation (RSD) was below 5% for all the target analytes. Finally, the recoveries obtained for different water samples of diverse origin (sea, river, irrigation channel and water treatment plant) ranged between 87 and 116%, thus showing no matrix effects.     

固相萃取/气相色谱-质谱分析大米中氟草烟残留

试样采用NaOH-甲醇溶液提取,经EASY柱固相萃取净化后,以甲醇为衍生剂,浓硫酸为催化剂,在93~98℃水浴条件下酯化后,以DB-5 MS柱为分离柱,气相色谱-质谱联用测定。试验结果表明,氟草烟质量浓度为0.05~2 mg/L时,与相应的峰面积或丰度成良好的线性关系,相关系数为0.999 6;添加质量浓度为0.050 0~0.200 mg/kg时,回收率为81%~98%,该法检出限为0.01 mg/kg。     

High resolution gas chromatographic determination of diterpenic alcohols and sterols in coffee lipids

Summary The composition of the unsaponifiable fraction of coffee lipids extracted before and after roasting was determined in two coffee types (Arabica and Robusta) of different geographic origin. Component identification was performed by gas chromatography-mass spectrometry. Large amounts of diterpene mono- and di-alcohols were found in both varieties; cafestol, kahweol and 16-O-methylcafestol were identified. Other components that were partly generated during roasting were also identified; these compounds seem to arise from the dehydration of cafestol and dehydrocafestol.     

High resolution gas chromatographic determination of diterpenic alcohols and sterols in coffee lipids

Summary The composition of the unsaponifiable fraction of coffee lipids extracted before and after roasting was determined in two coffee types (Arabica and Robusta) of different geographic origin. Component identification was performed by gas chromatography-mass spectrometry. Large amounts of diterpene mono-and di-alcohols were found in both varieties; cafestol, kahweol and 16-O-methylcafestol were identified. Other components that were partly generated during roasting were also identified; these compounds seem to arise from the dehydration of cafestol and dehydrocafestol.     

Simultaneous determination of pentachlorophenol and carbaryl in water

Summary A rapid method for the simultaneous determination of pentachlorophenol (PCP) and Carbaryl in water is described. A 1 liter water sample is extracted with hexane after acidification with concentrated H₂SO₄. After evaporation to a small volume, the extract is analyzed by gas chromatography-mass spectrometry, operating in the selected ion monitoring mode. Estimated detection limits are 0.08 g L^–1 for PCP and 0.11 g L^–1 for Carbaryl, with recoveries of 96% for PCP and 97% for Carbaryl.     

X-ray studies of lanthanide(III) complexes with 4-hydroxy-3-methoxybenzoate anion

Polycrystalline complexes of lanthanide(III) with 4-hydroxy-3-methoxybenzoic acid were obtained as hydrated compounds of general formula Ln(C₈H₇O₄)₃?·?nH₂O. After slow recrystallization we obtained single crystals of complexes and determined their structures. Praseodymium(III) and neodymium(III) form isostructural dihydrated complexes [Ln(C₈H₇O₄)₃(H₂O)₂], which crystallize in the triclinic system, space group P 1. Sm(III), Eu(III), Gd(III), Ho(III) and Tb(III) compounds are hexahydrates and also crystallize in the triclinic system, space group P 1. Dihydrated compounds form polymeric chains with metal centres linked by oxygen atoms of bridging carboxylates. Each metal ion is coordinated by chelating carboxylic group and two water molecules. Complexes of the second isostructural group form dinuclear units [Ln₂(C₈H₇O₄)₆(H₂O)₄]?·?8H₂O. Lanthanide(III) ions are linked by oxygen atoms of two chelating–bridging carboxylate groups. In the dimeric structure each metal ion coordinates additionally two chelating carboxylic groups and two water molecules.     

A sequential injection method for the fluorimetric determination of aluminum in drinking water using 8-hydroxy-7-(4-sulfo-1-naphthylazo)-5-quinoline sulfonic acid

A robust and simple sequential injection (SI) method for the assay of aluminum ions in drinking water is described. The method is based on the complex formation between aluminum and 8-hydroxy-7-(4-sulfo-1-naphthylazo)-5-quinoline sulfonic acid (HSNQ). The fluorescence of the complex is monitored at an emission wavelength of 492 nm with excitation at 357 nm. The HSNQ concentration, aspirated reagent and sample volumes were optimized simultaneously using 3(3) full factorial design. The optimum operating conditions are aspirated sample and reagent volumes of 90 and 70 microL, respectively, and HSNQ concentration of 20 microM. With these conditions linear calibration curves were obtained from 100 to 800 ppb. The detection limit was 4 ppb. The maximum relative standard deviation of the method was 1.43% (n=5). The method was successfully applied for the determination of aluminum in drinking water samples.     

Analysis of chloroacetanilide herbicides in water samples by solid-phase microextraction coupled with gas chromatography-mass spectrometry

A solid-phase microextraction (SPME) method has been developed for the determination of 3 chloroacetanilide herbicides in both fresh and seawater samples. The extracted sample was analyzed by gas chromatography with mass spectrometry detection (GC-MS), and parameters affecting SPME operation including fibre type, sample pH, sample temperature, mixing speed and extraction time have been evaluated and optimized. The amount of dissolved organic matter (DOM) and the salt content both affected SPME extraction efficiency, but the presence of other competitive extractants such as organochlorine pesticides (OCPs) in the matrix showed no insignificance interference. The limit of detection (LOD) for acetochlor, metolachlor and butachlor were 1.2, 1.6 and 2.7 ng L⁻¹, respectively. The recoveries for the herbicides ranged from 79 to 102%, and the linear dynamic range was from 10 to 1000 ng L⁻¹. The developed method has been used to monitor herbicides contaminations in coastal water samples collected around Laizhou bay and Jiaozhou bay in Shandong peninsula, China. The concentrations of acetochlor and metolachlor ranged from undetectable to 78.5 ng L⁻¹ and undetectable to 35.6 ng L⁻¹, respectively. Butachlor was not observed but in only one sample and the concentration is lower than the limit of quantification (LOQ). The concentrations of the three herbicides in this study are low compared to most of the other places reported.     

Synthesis,crystal structures and spectral characterization of Cu(II) and Mn(II) complexes of 4-hydroxy-3-methoxybenzaldehyde: antioxidant properties and molecular docking studies

[Cu(L)₂(H₂O)₂] (1) and [Mn(L)₂(H₂O)₂] (2) (HL = 4-hydroxy-3-methoxybenzaldehyde) were synthesized and characterized using elemental, spectral (FTIR, ESI-MS, UV–visible, fluorescence and EPR), thermal, cyclic voltammetric, powder, and single crystal X-ray crystallographic studies. Spectral and X-ray data ascertained the structural features, binding modes of ligand and distorted octahedral geometry around the metal ions. Cyclic voltammetric studies confirmed the formation of a quasi reversible redox couple in solution. Crystal structure analysis of 1 and 2 reveal the presence of non-covalent interactions, resulting in a 1-D polymeric chain. Antioxidant properties (using DPPH and hydrogen peroxide assay) and molecular docking studies (using 1BNA) are also examined. The binding free energies (calculated from docked models), ?270 (1) and ?295 kJ mol^?1 (2), suggest that the complexes reasonably bind to DNA, and the DNA-binding affinity of 2 is stronger than that of 1.     

Analytical Method Development for the Simultaneous Determination of Five Human Pharmaceuticals in Water and Wastewater Samples by Gas Chromatography-Mass Spectrometry

Summary Effective analytical methods for the simultaneous determination of five pharmaceuticals from various therapeutic classes in a variety of aqueous samples have been developed and method performance data are presented. The method involves the simultaneous extraction of the selected pharmaceuticals from the aqueous phase by solid phase extraction using a hyper cross linked, polystyrene-divinylbenzene polymer based sorbent. Analytes were eluted with methanol, derivatised with N-methyl-N-trimethylsilyltrifloroacetamide and analysed by gas chromatography – electron ionisation mass spectrometry (GC-EI-MS). Recoveries of 50 to 98% were established for waters spiked with the studied compounds at the low ng L^–1 level with the highest detection sensitivities being achieved in the selected ion monitoring (SIM) mode and the quantification limit of the procedure for sample sizes of 1000 ml was approximately 5 ng L^–1 for all matrices except sewage which was only tested to 20 ng L^–1. Analysis of domestic sewage from a large treatment works demonstrate the presence of all five compounds in both influents and effluents.     

(9Z,12Z,15Z)-十八碳三烯醛的GC-MS分析

（9Z，12Z，15Z）－十八碳三烯醛是美国白蛾信息素的主要成效成分之一，在其合成的过程中，采用气相色谱监测分离提纯效果；提纯的样品成分在化学方法、IR、^1H NMR波谱分析基础上用气相色谱－质谱鉴定为该化合物，并用气相色谱的面积归一化法测得其含量大于99％；该法简单、准确可靠、无需标样。