空壳纳米金修饰的新型DNA传感器

利用新型材料金纳米空球, 通过层层修饰的技术, 分别将壳聚糖、空壳纳米金、L-半胱氨酸、细胞色素c以及ssDNA探针修饰到玻碳电极表面, 制备了一种新型的DNA生物传感器. 以紫外及透射电子显微镜(TEM)表征了空壳纳米金, 以循环伏安法、阻抗谱图等电化学方法研究了传感器的特性, 通过原子力显微镜方法观察了该DNA生物传感器不同层之间的形态差异. 结果表明, 该修饰电极所吸附的ssDNA探针为1.672×10^―10 mol•cm^－2. 在指示剂柔红霉素的帮助下, DNA探针可与互补的DNA进行杂交, 借此以微分脉冲伏安法测定DNA.     

DNA电化学生物传感器在转基因植物特定序列基因检测中的应用

在玻碳电极(GCE)上采用循环伏安法电聚合硫堇(PTh)得到PTh/GCE修饰电极,并利用聚硫堇层共价结合和静电作用吸附金纳米粒子(AuNP′s)制得AuNP′s/PTh/GCE修饰电极。然后通过将ss-DNA/AuNP′s/PTh修饰电极置于cDNA杂交液中,于42℃杂交制得ds-DNA/AuNP′s/PTh修饰玻碳电极,实现了脱氧核糖核酸(DNA)探针在AuNP′s/PTh修饰的玻碳电极上的固定,制得DNA电化学生物传感器。在[Fe(CN)6]3-/4-溶液中采用微分脉冲伏安法(DPV)及交流阻抗谱技术(EIS)对DNA的固定和杂交进行了表征。试验结果表明:在1.0×10-10～1.0×10-6mol.L-1的浓度范围内,该传感器可对转基因植物外源基因草丁膦乙酰转移酶基因(PAT基因)片段进行检测,检出限(3s)为3.2×10-11mol.L-1。     

用于DNA杂交检测的丝网印刷型生物传感器的研究

将单链DNA(ssDNA)固定到丝网印刷碳电极上构成电化学DNA传感器,采用电化学指示剂,建立DNA杂交的检测方法.Co(phen)33+电化学指示剂通过钴盐与配体邻菲罗啉络合制备,采用等离子发射光谱法(ICP-AES)和核磁共振法(NMR)表征功能基团,采用循环伏安法(CV)分析指示剂的电化学特性,并以此为基础研究ssDNA在电极表面的固定及DNA杂交过程.本研究探讨了直接吸附、静电吸附与键合等3种ssD-NA在电极表面的固定方法,结果表明,静电吸附法和键合法具有较高的ssDNA固定量,采用静电吸附法固定探针的电极杂交目标DNA后,Co(phen)33+易于嵌入双链DNA (dsDNA)中,CV峰电流(ip)信号随目标DNA浓度增加.本研究采用静电吸附ssDNA的电极检测DNA杂交,实验表明,当探针固定液中ssDNA浓度为5 mg/L时,目标DNA浓度在6.65×10- 8～4.26× 10-6mol/L范围内,Co(phen)33+在dsDNA修饰电极上ip值与DNA浓度呈良好的线性关系,R2为0.9819.本研究为建立新的微生物分子分型手段提供了初步依据.     

氧化锆/聚亚甲基蓝修饰电极检测CaMV35S启动子基因

制备了基于氧化锆(ZrO_2)/聚亚甲基蓝(PMB)修饰电极的无标记DNA传感器,用于转基因植物CaMV35S启动子基因的检测。探针DNA(ssDNA)通过ZrO_2和DNA的磷酸基的相互作用修饰到电极表面,以PMB氧化峰的示差脉冲伏安响应为检测信号,传感器和完全互补的DNA片段杂交后,PMB的氧化峰电流明显降低,当和完全不匹配的DNA片段杂交时,峰电流无明显变化。对于完全互补的DNA片段,在2.0×10~(-12)~2.0×10~(-8) mol/L浓度范围内峰电流的变化值和浓度的对数成良好的线性关系,检测限为4.1×10~(-13) mol/L(S/N=3)。所制备的传感器具有良好的稳定性、再生性和重现性,用于样品检测,结果令人满意。     

纳米铂直接修饰玻碳电极的制备及在半胱氨酸中的电化学行为

采用一步化学原位还原法将球形纳米铂颗粒直接修饰在玻碳电极上,用SEM、EDS和电化学方法对该电极进行表征并与铂片电极、裸玻碳电极进行了对比。结果表明,纳米铂修饰电极的峰电流与扫描速度呈线性关系,纳米铂在电极表面覆盖率为1.28×10-7mol/cm2。循环伏安法研究结果表明纳米铂修饰电极对半胱氨酸的催化氧化作用和铂片电极相比提高了数倍,且峰电位负移了0.3V。在纳米铂修饰的玻碳电极上,半胱氨酸的浓度在1.0×10-7mol/L到1.0×10-5mol/L范围内和催化电流呈线性关系。     

量子点双标记的Fe3O4@Au磁性纳米DNA电致发光型传感器

合成了Fe3O4@Au磁性纳米粒子,并根据单链寡聚核苷酸(ss-DNA)杂交原理,利用量子点电化学发光,构建了DNA电化学传感器.在磁控玻碳电极(MCGCE)表面,将5′-SH-ssDNA捕获探针自组装在Fe3O4@Au磁性纳米粒子上,然后与目标DNA互补的一端杂交形成dsDNA,再与双标记了量子点的5′-NH2-ssDNA-NH2-3′信号探针杂交形成三明治杂交的DNA.应用循环伏安法对DNA的固定与杂交进行了表征.目标DNA浓度在1.0×10-13～1.0×10-11 mol/L范围与其响应的ECL信号呈线性关系,检出限为1.8×10-14mol/L.由于采用量子点双标记法,检测的灵敏度显著提高.     

基于多边形金纳米颗粒的非标记型可卡因适体传感器的研制

实验合成了多边形金纳米颗粒,通过壳聚糖(CHIT)将合成的多边形金纳米颗粒固定在玻碳电极表面,然后通过自组装技术将带巯基的捕获DNA探针固定在修饰有多边形金纳米颗粒的电极表面,利用杂交反应使可卡因适体与DNA捕获探针结合,制成非标记型可卡因适体传感器。以六氨合钌作为电化学指示剂,通过测量传感器与目标物可卡因结合前后电流变化情况对可卡因进行测定。考察了缓冲溶液的pH、可卡因培育时间、扫描速度等对测定的影响。结果表明,在pH为7.40时该传感器的检测范围为1.0×10-10～1.0×10-3 mol/L,检测限为3.0×10-11 mol/L。该传感器制作简单,响应好,抗干扰能力强。     

检测急性早幼粒细胞白血病PML-RARα融合基因的DNA传感器研制

利用共价键合法,将氨基修饰的具有急性早幼粒细胞白血病PML-RARα融合基因特异性的单链DNA探针固定在玻碳电极表面,构成急性早幼粒细胞白血病DNA传感器 (急粒DNA传感器).以电活性的芦荟大黄素(AE)为杂交指示剂,考察了杂交温度及传感器的特异性、重现性和检出限等性能.结果表明:AE在裸电极上的吸附常数为(4.5±0.2)×105 L·5mol-1,与单链DNA修饰的玻碳电极(ssDNA/GCE)和双链DNA修饰的玻碳电极(dsDNA/GCE)结合常数分别为(2.1±0.4)×105和(2.7±0.2)×105 L·5mol-1.这种新型的DNA传感器具有特异性强、灵敏度高和重现性好的优点.应用此方法于临床血清分析,初步探索了将该法应用于临床检测的可行性.     

氧化锆/聚中性红电化学DNA传感器用于转基因植物CaMV35S启动子基因序列的测定

制备了基于氧化锆(ZrO2)/聚中性红(PNR)修饰电极的电化学DNA传感器。探针DNA通过磷酸基和ZrO2的相互作用组装到电极表面。原子力显微镜(AFM)和电化学方法用于电极的表征。PNR在DNA杂交前后峰电流的变化作为杂交信号,用示差脉冲伏安法对转基因植物CaMV35S启动子基因片段进行测定。结果表明:探针DNA和完全互补的DNA片段杂交后,杂交信号明显变小,峰电流的变化值与其浓度的对数在1.0×10-11~1.0×10-8mol/L范围内呈良好的线性关系,检出限为3.46×10-12mol/L(S/N=3)。此外,传感器能区分互补、单碱基错配、完全错配的DNA序列,已用于样品的测定。     

基于树状高分子固定DNA的电化学生物传感器的研究

用电化学氧化法使玻碳电极表面氧化生成羧基,利用偶联活化试剂将1.0G树状高分子(PAMAM)固定在玻碳电极表面,并通过共价结合固定ssDNA。以亚甲基蓝为指示剂,采用循环伏安法、示差脉冲伏安法等电化学方法对DNA电化学生物传感器进行了表征。结果发现,通过亚甲基蓝与双链dsDNA作用的氧化还原电流的变化,可以识别和定量检测溶液中互补的ssDNA片段。经过条件优化,本法测定DNA的浓度线性范围为2×10-9～2×10-7mol/L,检出限为1×10-9mol/L。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.