La2O3 和CeO2对CH4-CO2重整Ni/MgO催化剂结构和性能的影响

采用共沉淀方法制备了NiO-MgO、NiO-La2O3-MgO、NiO-CeO2-MgO三种催化剂，用BET、XRD、TPR、XPS、TG及活性评价等方法考察了La2O3、CeO2助剂对NiO-MgO物化性质和CH4-CO2重整反应性能的影响.实验结果表明，三种催化剂中镍物种以镍镁固溶体形式存在.与NiO-MgO相比， NiO-La2O3-MgO、NiO-CeO2-MgO具有较高比表面积，且其镍物种可还原能力有所增强， NiO-CeO2-MgO尤为明显. La2O3、CeO2均在一定程度上改善了NiO-MgO的CH4-CO2重整反应性能，提高了镍晶粒的抗烧结能力.但二者的作用机制有所差异， La2O3和CeO2分别主要作为结构助剂和电子助剂发挥作用.     

铈和镧改性γ-Al2O3担载Pd催化剂的结构效应

分别以镧-铈、铈-镧顺序浸渍和镧铈共浸渍的方式在γ-Al2O3载体上引入助剂La2O3和CeO2，然后担载Pd制备了一系列催化剂.以甲醇分解为探针反应，采用XRD、EXAFS和XPS对催化剂的体相和表面结构进行表征，用BET法测定比表面积，并进行了吸附态CO的FTIR研究.结果表明,La2O3容易进入CeO2的晶格中，促进了CeO2在γ-Al2O3上的分散.但不同的La2O3、CeO2加入方式对活性组分Pd在改性载体上的分散度、优势暴露面及其与CeO2之间的相互作用产生不同的影响.关联甲醇分解性能测试结果说明,Pd在载体上的高度分散以及Pd和CeO2之间通过界面产生的强相互作用是催化剂具有高活性的关键.     

预还原催化剂LaNiO3, La4Ni3O10, La3Ni2O7和La2NiO4 催化分解CH4制碳纳米管 的研究

通过预还原的LaNiO3,La4Ni3O10,La3Ni2O7和La2NiO4催化分解CH4可以制备大量高度石墨化的碳纳米管。还原前后的催化剂的结构和组分通过X射线衍射(XRD)测定。所制得的碳纳米管由扫描电镜(TEM)、X射线光电子能谱(XPS)表征。碳纳米管在空气在的热氧化性由热重实验(TG)测定。实验结果表明不同催化剂前驱中的La/Ni比会影响碳纳米管的管径分布和石墨化程度。La/Ni比越小,碳纳米管的管径越大,石墨化程度越高。     

Autothermal reforming of methane over Ni catalysts supported over ZrO2-CeO2-Al2O3

Ni catalysts supported on Al2O3, ZrO2-Al2O3, CeO2-Al2O3 and ZrO2-CeO2-Al2O3 were prepared by coprecipitation method, and their catalytic performances for autothermal reforming of methane to hydrogen were investigated. The Ni-supported catalysts were characterized by XRD, TPR and XPS. The relationship between the structures and catalytic activities of the catalysts was discussed. The results showed that the catalytic activity and stability of the Ni/ZrO2-CeO2-Al2O3 catalyst was better than those of other catalysts with the highest CH4 conversion, H2/CO and H2/COx ratio at 750 ℃. The catalyst showed a little deactivation along the reaction time during its 72 h on stream with the mean deactivation rate of 0.08%/h. The catalytic performance of the Ni/ZrO2-CeO2-Al2O3 catalyst was also affected by reaction temperature, no2 ： nCH4 molar ratio and nH2O ： nCH4 molar ratio. TPR, XRD and XPS measurements indicated that the formation of ZrO2-CeO2 solid solution could improve the dispersion of NiO, and inhibit the formation of NiAl2O3, and thus significantly promoted the catalytic activity of the Ni/ZrO2-CeO2-Al2O3 catalyst.     

超细镍基催化剂的CH4—CO2重整反应性能——Ⅲ制备方法对催化剂吸附CO2性能的影响

采用溶胶－凝胶法和超临界干燥技术,制备了气凝胶超细氧化铝载体、超细二元（NiO-Al2O3）和三元（NiO-La2O3-Al2O3）催化剂,同时以超细氧化铝载体浸渍镍盐的二元催化剂和普通氧化铝浸渍的镍镧铝的三元催化剂作为对比。通过CO2－TPD实验及XRD、XPS和IR技术表征,考察了制备方法和氧化镧改性对催化剂吸附二氧化碳能力的影响。结果表明,超细样品的吸附能力明显高于浸渍型催化剂,具有明显的纳米粒子效应,La2O3的加入,提高了强碱中心数,使催化剂的吸附能力显著增强,且不受制备方法的影响,还原后的镍物种吸附CO2后,与载体之间的相互作用被消弱,容易被重新氧化成粒度较大的氧化镍晶粒。     

La和Bi对乙炔与甲酸甲酯加氢酯化合成丙烯酸甲酯的镍基催化剂性能的影响(英文)

在２２０℃和５０－６０大气压条件下,利用固定床对ＮｉＯ／ＳｉＯ２、ＮｉＯ／Ａｌ２Ｏ３、ＮｉＯ－Ｌａ２Ｏ３／Ａｌ２Ｏ３和ＮｉＯ－Ｂｉ２Ｏ３／Ａｌ２Ｏ３催化剂上的乙炔与甲酸甲酯加氢酯化合成丙烯酸甲酯进行了研究。镍基催化剂对乙炔的加氢酯化合成丙烯酸甲酯具有很好的活性。用浸透法制备的Ｍｏ／ＳｉＯ２催化剂的活性和丙烯酸甲酯的选择性均比离子交换法差。ＮｉＯ／Ａｌ２Ｏ３催化剂用Ｌａ或Ｂｉ改性后,其催化活性大大提高。ＸＰＳ、ＸＲＤ和ＴＰＲ结果表明,当催化剂用Ｌａ或Ｂｉ改性后,ＮｉＯ的晶粒明显减小,催化剂表面的Ｎｉ／Ａｌ原子比增大,催化剂的第二个还原峰温大大降低。     

TiO2对Ni/Al2O3催化剂CO甲烷化性能的影响

采用溶胶凝胶法制备了一系列不同TiO₂含量的TiO₂-Al₂O₃复合载体,并通过浸渍法制备了NiO/TiO₂-Al₂O₃催化剂。分别考察了不同TiO₂含量的NiO/TiO₂-Al₂O₃催化剂及反应温度对CO甲烷化催化性能的影响。实验结果表明,当复合载体中TiO₂质量分数为30%,反应温度为350～450 ℃时,催化剂催化活性较高。利用N₂吸附-脱附(BET)、X射线衍射(XRD)及H₂程序升温还原(H₂-TPR)等手段对催化剂物化性能进行了表征。结果表明,加入适量的TiO₂能抑制镍铝尖晶石NiAl₂O₄物种的生成,改善NiO的表面分散性能,避免大晶粒NiO的形成,也改善了催化剂的还原性能,从而提高催化剂的CO甲烷化活性。     

Effect of CeO2 on the catalytic performance of Ni/Al2O3 for autothermal reforming of methane

The effect of promoter Ce on the catalytic performance of Ni/Al2O3 catalyst for autothermal reforming of methane to hydrogen was investigated. The catalysts were characterized by X-ray diffraction （XRD）, temperature-programmed reduction （TPR）, and X-ray photoelectron spectroscopy （XPS）. The results indicated that the catalytic performance of the catalysts was improved with the addition of Ce. Ni/Ce30Al70Oδ showed the highest CH4 conversion in operation temperatures ranging from 650 ℃ to 850 ℃. At the same time, the decrease in H2/CO ratio with increasing reaction temperature was consistent with the fact that water-gas shift reaction was thermodynamically unfavorable at higher temperatures. The XRD result indicated that adding Ce to Ni/Al2O3 catalyst prevented the formation of NiAl2O4 and facilitated the formation of NiO. The formation of NiO increased the number of active sites, resulting in higher activity. Comparing the TPR profiles of Ni/Ce30Al70Oδ with Ni/Al2O3, it could be clearly observed that with the addition of Ce, the total reduction peak areas in the middle and low temperatures increased. It was most probably that the addition of Ce inhibited the stronger interaction between Ni and Al2O3 to form the phase of NiAl2O4, and favored the formation of the strong interaction between NiO species and CeO2. Therefore, the addition of Ce to the Ni/Al2O3 catalyst increased the active surface that promoted the activity of the catalyst.     

助催化剂Sm2O3对甲烷化镍催化剂的作用

金属镍催化剂广泛地应用于石油、化肥等工业.八十代初,人们发现稀土氧化物能有效地提高甲烷化镍催化剂性能,并加强了对其添加效应以及作用机理的研究.但此类报道主要集中于La_2O_3、CeO_2等,而对其它稀土氧化物报道甚少.本文采用XRD、TEM、XPS和TPSR等手段,探讨了添加Sm_2O_3对甲烷化镍催化剂的作用,并比较了2种浸渍法所产生的结果.     

Ni-Cu/La2O3催化剂上甲烷部分氧化制合成气

用浸渍法制备了不同Cu质量分数的Ni Cu/La2O3双金属催化剂，考察了金属浸渍顺序和Cu质量分数对催化剂甲烷部分氧化性能的影响,并通过BET、XRD、TPR和SEM等技术对催化剂进行了表征。结果表明,在甲烷部分氧化制合成气反应中，Cu助剂的添加对Ni/La2O3催化剂的活性有一定的改进作用，其中浸渍顺序对催化剂的性能影响很大，共浸渍制备的催化剂活性相对较好；Cu质量分数为5%~7%时催化剂有较好的活性和稳定性；XRD等测试表明,Cu和Ni金属由于相同的晶型结构及离子半径在制备过程中形成了双金属固溶体，提高了活性组分Ni的分散度，减少了Ni晶粒的烧结聚集长大，从而提高了催化剂的活性和稳定性。     

Methane Decomposition over Ni/α-Al2O3 Promoted by La2O3 and CeO2

The decomposition of methane on Ni/a-Al2O3 modified by La2O3 and CeO2 with differ-ent contents has been investigated and the ralationship between methane decomposition and removal of carbon by CO2 over these catalyst has also been studied by pulse-chromatography. The catalysts were characterized by TPR and XRD. It was shown that Ni/a-Al2O3 could be promoted by adding La2O3, and the carbon species produced over this catalyst was activated and eliminated by CO2. But CeO2 would suppress the decomposition of methane over Ni crystallite. Both La2O3 and CeO2 can inhibit aggregation of the Ni particles. Decomposition of methane over the Ni-based catalysts is structure sensitive to a certain extent.     

Methane Decomposition over Ni/α-Al_2O_3 Promoted by La_2O_3 and CeO_2

The decomposition of methane on Ni/a-Al2O3 modified by La2O3 and CeO2 with different contents has been investigated and the ralationship between methane decomposition and removal of carbon by CO2 over these catalyst has also been studied by pulse-chromatography. The catalysts were characterized by TPR and XRD. It was shown that Ni/a-Al2O3 could be promoted by adding La2O3, and the carbon species produced over this catalyst was activated and eliminated by CO2. But CeO2 would suppress the decomposition of methane over Ni crystallite. Both La2O3 and CeO2 can inhibit aggregation of the Ni particles. Decomposition of methane over the Ni-based catalysts is structure sensitive to a certain extent.     

CH4,CO2和O2制合成气反应中载体对Ni催化剂抗氧化性能的影响

在ＣＨ４、ＣＯ２ 催化氧化制合成气反应中, Ｎｉ／Ａｌ２Ｏ３ 催化剂在高温下生成ＮｉＡｌ２Ｏ４ 尖晶石,是导致催化剂失活的一个重要因素． 通过向载体（Ａｌ２Ｏ３）中添加各种氧化物, 使得催化剂的抗氧化性能得到改善． 并运用ＴＰＲ、ＸＲＤ对催化剂进行表征, 发现催化剂的抗氧化性顺序为： Ｎｉ／ＣａＯ－Ａｌ２Ｏ３ ＞ Ｎｉ／ＭｇＯ－Ａｌ２Ｏ３ ＞ Ｎｉ／ＣｅＯ２－Ａｌ２Ｏ３ ＞ Ｎｉ／Ｌａ２Ｏ３－Ａｌ２Ｏ３ ＞ Ｎｉ／Ｙ２Ｏ３－Ａｌ２Ｏ３ ＞ Ｎｉ／ＴｉＯ２－Ａｌ２Ｏ３＞ Ｎｉ／Ａｌ２Ｏ３＞ Ｎｉ／Ｆｅ２Ｏ３－Ａｌ２Ｏ３．     

Influence of CeO2 and La2O3 on properties of palladium catalysts used for emission control of natural gas vehicles

Pd/YZ-Al2O3 (Y and Zr modified Al2O3, and hereafter, labelled as Al) catalysts with 4 wt% additive CeO2 and/or La2O3 were prepared and characterized by X-ray photoelectron spectroscopy (XPS), NO-temperature programmed desorption (NO-TPD), N2-adsorption/desorption (Brunauer-Emmet-Teller BET method), X-ray diffraction (XRD) and CO-chemisorption. Catalytic activities for CH4, CO and NO conversion were tested in a gas mixture simulated the emissions from natural gas vehicles (NGVs) operated under stoichiometric conditions. The results indicated that all catalysts exhibited excellent catalytic performances for CH4 and CO oxidation and the promoting effect of CeO2 or La2O3 was significant for NO conversion. XPS results showed that the electron density around Pd was increased by CeO2 and/or La2O3, the binding energy of Pd 3d decreased as the order: Pd/Al>Pd/Ce/Al>Pd/La/Al>Pd/CeLa/Al. The electron-rich Pd showed Rh-like catalytic properties which exhibited good activity for the reduction of NO. NO-TPD results showed that the addition of CeO2 and/or La2O3 increased NO adsorption on surface, and promoted the conversion of NO.     

PROMOTING EFFECT OF RARE EARTH OXIDES ON Ni/Re_xO_y-Al_2O_3 CATALYST FOR PARTIAL OXIDATION OF METHANE TO SYNTHESIS GAS

IntroductionSynthesisgas(HZ CO)isproducedfrommethanemoshybysteamrefonningwhichsuffersfromlimitationssuchasveryhighenergyrequirements,complicatedequipmentandinstallations,highHZ/COproductratioandpoorselectivityforcarbonmonoxide.Recently,manyresearchershave…     

甲烷部分氧化Ni催化剂及助剂的研究

考察了不同Ni担载量的Ni／a－Al_2O_3催化剂的催化性能，以8％Ni（质量分数）最佳．XRD分析表明，8％Ni催化剂表面NiO颗粒最小．TPR分析表明，催化剂表面主要有两种不同化学环境的NiO，当Ni担载量超过12％时，表面开始出现“游离态”NiO，这部分NiO易使催化剂积碳．添加稀土Ce有利于提高Ni催化剂的活性、选择性和稳定性，并对Ce的助剂效应作了研究．     

La2O3对Ni/γ-Al2O3甲烷化催化剂的助催化作用

我国将稀土作为助剂引入镍基甲烷化催化剂,大大提高了催化剂的活性和热稳定性,并已投入工业应用［1－3］．稀土对不同镍催化剂反应性能及其作用机理的研究已有一些报导［3－7］．谢有畅等观察到镍负载在经单层La2O3改性的γ－Al2O3表面,其晶粒要比没有La2O3时小得多．Rotgerink等认为添加La后反应速率的增加不只是由于几何效应,而是La对甲烷化本身有促进作用,单位镍表面的活性是随La含量不同而改变的,活性增加的同时表观活化能也增加［5］．作为助剂的La2O3在氢还原和反应过程中的变化及其作用的研究和讨论较少,目前一般认为添…     

担载镍催化剂上乙炔与甲酸甲酯加氢酯化合成丙烯酸甲酯:担载量和焙烧温度的影响(英文)

以ＮｉＯ担载量为０．０８ｗｔ％～１８．７ｗｔ％及焙烧温度为６２３ Ｋ～８７３ Ｋ的ＮｉＯ／Ａｌ２Ｏ３催化剂进行乙炔与甲酸甲酯的加氢酯化反应,并结合ＴＰＲ、ＸＰＳ、ＸＲＤ和ＢＥＴ技术对催化剂进行表征。催化剂在制备过程中,镍离子与载体氧化铝间的相互作用产生两种不同的镍物种,ＮｉＯ晶相和ＮｉＡｌ２Ｏ４类物种,它们间的比例随担载量及焙烧温度而异,因而表现出其对乙炔与甲酸甲酯加氢酯化不同的反应性能。实验结果表明,在７７３ Ｋ焙烧的１０Ｗｔ％ＮｉＯ／Ａｌ_２Ｏ_３最适合乙炔与甲酸甲酯的加氢酯化反应。     

EFFECTS OF ALKALI AND RARE EATTH METAL OXIDES ON THE THERMAL STABILITY AND THE CARBON DEPOSITION OVER A NiO/Al_2O_3 CATALYST

采用固定床流动反应装置、ＣＯ吸附、ＴＧ、ＴＰＯ、ＸＰＳ和ＸＲＤ等手段考察了ＮｉＯ／Ａｌ２Ｏ３和ＬｉＮｉＬａＯ／Ａｌ２Ｏ３催化剂上的甲烷部分氧化反应。实验结果表明，ＬｉＮｉＬａＯ／Ａｌ２Ｏ３对甲烷部分氧化反应具有较高的反应活性。锂和镧的添加不仅改善了活性组分镍的分散度，而且提高了ＮｉＯ／Ａｌ２Ｏ３的抗积碳能力和热稳定性     

CeO2、CaO助剂对甲烷部分氧化制合成气Ni/MgOAl2O3催化剂结构和性能的影响

采用BET、H2 TPR、XRD、TEM和活性评价等表征手段，考察了CeO2、CaO助剂对Ni/MgOAl2O3催化剂物化性质和甲烷部分氧化制合成气反应性能的影响。实验结果表明，单独加入CeO2或CaO助剂可以改善Ni/ MgOAl2O3催化剂中镍物种的还原性能，以CaO尤为明显；CaO作为结构助剂可以降低还原态催化剂中的镍晶粒尺寸，使改性的催化剂具有较好的活性，而CeO2对催化剂的活性未产生显著影响。当CeO2与CaO两种助剂同时对Ni/MgOAl2O3进行改性时，虽然催化剂中镍物种的还原性能没有发生明显变化，但仍具有很好的反应性能，这与CeO2与CaO能够形成CaO-CeO2固溶体有关。CaO-CeO2固溶体不仅与镍物种间存在相互作用，提高了镍物种的分散度、减小了镍晶粒尺寸，还可以提高催化剂的储氧能力和晶格氧的流动性，从而有利于改善其甲烷部分氧化反应性能。