TiO_2-Al_2O_3复合载体的制备及Co-Mo/TiO_2-Al_2O_3催化剂加氢脱硫性能的研究

通过改进的溶胶-凝胶法(SG)、共沉淀法(CP)、表面沉淀法(PR)及混捏法(ME)制备TiO_2-Al_2O_3复合载体,考察了不同制备方法对复合载体物理性质的影响。采用浸渍法制备Co-Mo/TiO_2-Al_2O_3-X加氢脱硫催化剂,研究了Co-Mo/TiO_2-Al_2O_3-X加氢脱硫催化剂的脱硫性能。利用XRD、BET、SEM等表征手段对复合载体及催化剂进行表征分析。结果表明,SG法制备的复合载体粒径均一,具有较大的比表面积、孔径和孔体积;CP法制备复合载体时TiO_2以单层或亚单层的分散状态高度分散于γ-Al_2O_3中。在氢气压力3.0 MPa、反应温度280℃、反应时间4 h、液时空速1.4 h-1和氢油比600的条件下,SG法制备的Co-Mo/TiO_2-Al_2O_3催化剂具有较高加氢脱硫活性,噻吩转化率达到96.6%。     

Co-Mo/Al2O3和Ru-Co-Mo/Al2O3催化剂的不同表面钴中心表征

利用IR、MS方法对还原态的Co-Mo/Al_2O_3和Ru-Co-Mo/Al_2O_3催化剂进行了考察。结果表明, 还原态的Co-Mo/Al_2O_3和Ru-Co-Mo/Al_2O_3表面上存在着不同的Co中心。可以十分明显地观察到, 在Co-Mo/Al_2O_3上, NO吸附的红外光谱显示了1895和1880 cm~(-1)谱带; 在TPD-MS图上显示了353, 423和473 K谱峰。通过比较Co-Mo/Al_2O_3和Ru-Co-Mo/Al_2O_3, 提出了在Ru-Co-Mo/Al_2O_3中Ru的加入主要是提高了NO在催化剂上的吸附速率和吸附量, 增强吸附键的强度。     

二甲基二硫醚对Ni/Al_2O_3催化剂加氢性能的影响

考察了二甲基二硫醚(CH3SSCH3)对Ni/Al2O3催化剂上苯、环己烯和苯乙烯加氢活性的影响,并采用BET、XRD、H2-TPR、XPS、SEM和EA等手段对催化剂进行表征。实验结果表明,在CH3SSCH3存在下,Ni/Al2O3催化剂对苯和环己烯加氢迅速失活,且环己烯加氢对CH3SSCH3的耐硫性要略强于苯加氢,而苯乙烯中共轭烯烃的加氢转化率则维持100%长时间不变。CH3SSCH3的影响顺序为芳环单烯烃共轭烯烃。此外,通过设计实验研究了CH3SSCH3对催化剂的毒化机理,发现CH3SSCH3分子首先吸附在催化剂的表面,并发生氢解生成甲烷随尾气逸出,故CH3SSCH3分子中碳对催化剂的失活影响较小,而留下的硫原子则与镍活性组分发生相互作用,毒化催化剂。     

工业NiW/Al2O3催化剂上二苯并噻吩的加氢脱硫动力学

以二苯并噻吩(DBT)为含硫模型化合物, 在高压滴流床反应装置中,考察了工业NiW/Al2O3催化剂（RN-10）的加氢脱硫(HDS)动力学规律,研究了氢分压（1.5 MPa～4.5 MPa）、氢油体积比（150~700）、液体质量空速(15 h-1~60 h-1）、反应温度（280 ℃~380 ℃）等对DBT的HDS反应结果的影响。结果表明,当氢分压和氢油体积比较大时,两者变化对DBT的转化率基本无影响;温度对DBT的转化率影响较大,提高温度可有效提高DBT的转化率,随着温度的升高,DBT转化率的增加逐渐变缓。采用2级平推流反应动力学模型对不同温度实验数据进行了拟合,求得了不同温度的表观反应速率常数,模型的相关系数>0.989。活化能计算结果表明,RN-10催化剂在高反应温度区(>330 ℃)的DBT的HDS活化能明显低于较低温度时的活化能,分别为13.4 kJ/mol和121.4 kJ/mol。对于RN-10催化剂,不可单纯地通过提高反应温度来大幅度提高HDS转化率。     

磷对预硫化型NiMo/Al2O3催化剂加氢脱硫脱氮性能的影响

利用等体积浸渍法制备了不同磷含量的预硫化型NiMo/Al2O3催化剂,并利用XRD、BET、TPR和HRTEM等分析方法对其进行了表征,研究了磷对其加氢脱硫脱氮性能的影响.结果表明,由于预硫化型NiMo加氢催化剂上活性组分和载体的相互作用较弱,MoS2或Ni-Mo-S相主要以TypeⅡ形式存在,磷通过增加MoS2的堆积...     

Co-Mo/SiO2-Al2O3润滑油加氢处理催化剂的制备

以Pluronic P₁₂₃作结构导向剂,采用Al （NO₃）₃-NaAlO₂双水解法合成氧化铝,在成胶过程中加入正硅酸乙酯,制备硅质量分数分别为5%、10%、15%的SiO₂-Al₂O₃载体,并通过共浸渍法制备出Co-Mo/SiO₂-Al₂O₃润滑油加氢处理催化剂。通过XRD、N₂吸附-脱附、Py-FTIR、NH₃-TPD、H₂-TPR、TEM和XRF等手段对载体及催化剂的性质进行表征。结果表明,硅质量分数为10%的SiO₂-Al₂O₃具有优良的孔结构、较多的中强酸以及部分有序的介孔结构。以此为载体制备的Co-Mo/10% SiO₂-Al₂O₃催化剂中,MoS₂颗粒均匀地分散在载体上,具有更多的B酸性位和Ⅱ型CoMoS活性相。以减二线蜡油为原料油的固定床活性评价结果表明,生成油中主要组分为链烷烃与环烷烃;尤其Co-Mo/10% SiO₂-Al₂O₃催化剂具有优良的加氢性能,在15 MPa、380℃、氢油比为1000、空速为0.6 h^-1的反应条件下,其HDS和HDN数值均超过99%,产品中S含量小于10 μg/g,N含量小于2 μg/g,可以满足后续异构脱蜡等对原料的要求。     

Fe改性对Ru/Al_2O_3催化剂的马来酸二甲酯加氢性能影响

以Al2O3为载体,采用吸附-沉淀法制备一系列Ru-Fe/Al2O3催化剂,并进行了H2-TPR、XRD及XPS表征。以马来酸二甲酯(DMM)催化加氢合成丁二酸二甲酯(DMS)为探针反应,考察了Fe的加入对Ru/Al2O3催化性能的影响。评价结果表明,当Fe/Ru原子比小于2时,催化剂活性变化不大;但Fe/Ru原子比大于或等于2时,催化剂活性明显增加;与Ru/Al2O3催化剂相比,Fe的加入改善了催化剂的高温氧化还原处理稳定性。以甲醇为溶剂,在70℃、1.0 MPa压力、600 r/min转速下,Ru-Fe/Al2O3催化DMM的转化率与生成DMS的选择性均接近100%。XPS和H2-TPR表征结果表明,Ru-Fe/Al2O3中Fe与Ru产生较强的相互作用,促进Ru的分散且调变了Ru的电子特性。     

汽油催化裂化脱硫USY/ZnO/Al_2O_3催化剂

提出了汽油经催化裂化脱硫的技术路线，并对催化剂进行了研究.综合采用浸渍和共沉淀法制备的USY/ZnO/Al_2O_3汽油催化裂化脱硫催化剂在固定床反应装置上评价结果表明，具有优异的脱硫活性和硫化物裂化选择性.脱除的硫绝大多数以H_2S的形式进入到裂化气中，仅有少量沉积在催化剂上，这有利于硫的回收利用和环境保护.硫化物的裂化脱硫是裂化和氢转移反应协同作用的结果，高温有利于裂化反应,而相对较低的温度对氢转移有利，420 ℃左右为汽油裂化脱硫的最佳温度是这对矛盾作用的结果.     

ZrO2及其含量对Pd/ZrO2-Al2O3催化剂加氢脱硫性能的影响

采用浸渍法制备了一系列Pd/ZrO2-Al2O3催化剂,并考察了ZrO2-Al2O3复合载体及其ZrO2含量对Pd基催化剂噻吩加氢脱硫(HDS)性能的影响,运用XRD和NH3-TPD等手段对催化剂进行了表征。结果表明,ZrO2-Al2O3复合载体及其ZrO2含量对Pd基催化剂的HDS性能有较大的影响,其中ZrO2含量为12wt%时Pd/ZrO2-Al2O3催化剂的活性最好。ZrO2-Al2O3复合载体及其ZrO2含量对Pd基催化活性的影响是通过增加Pd的分散度、H吸附量和催化剂的酸量、以及降低活性组分与载体的相互作用来实现。     

配合物的配位基团性质对CoMo/γ-Al_2O_3催化剂加氢脱硫性能的影响

选择四种不同配位基团的双齿配位分子乙二胺(EN)、乙醇胺(EA)、乙二醇(EG)和丙二酸(MA)对CoMo/γ-Al_2O_3催化剂改性,比较了它们对二苯并噻吩HDS性能的影响。结果表明,其活性顺序为CoMo(EN)CoMo(EA)CoMo(EG)≈CoMo(MA)CoMo,反应以直接脱硫路径为主,随反应温度升高,加氢路径的占比增加,加入配合物后可以促进加氢路径脱硫,CoMo(EN)催化剂具有最高的加氢活性。采用UV-vis、EA、XPS和HRTEM等手段对催化剂进行表征,结果表明,-NH_2与Co~(2+)有强络合作用,-COOH主要是静电作用,而-OH与钴离子没有相互作用。配位基团和Co~(2+)的相互作用,与HDS活性直接相关。配合物与Co~(2+)的结合可以有效生成Co-Mo-S活性相,且配合物碳化减弱载体与活性相的相互作用,有利于生成有更高本征活性的II型活性相。     

Weakening internal diffusion effect in selective hydrodesulfurization of FCC gasoline by novel designed eggshell CoMoS/Al2O3 catalysts

A simple method for preparation of presulfided eggshell CoMoS/γ-Al2O3 catalysts with sharp boundary is developed, through which the eggshell thicknesses of Co and Mo could be easily regulated by controlling the impregnation time. According to the results characterized by EDS, XRD, HRTEM and FT-IR of adsorbed CO, the active component structures, the nature and/or the amount of active sites on the eggshell catalyst are similar to these on the uniform catalyst. The evaluation results of the catalytic performance in selective hydrodesulfurization (HDS) of FCC gasoline show the presence of significant internal diffusion inhibition effect on HDS of S-compounds especially in the uniform catalyst. Compared with uniform catalyst, the eggshell catalyst could remarkably reduce such an internal diffusion inhibition effect due to a shortened diffusion path of the reactants, thus showing higher HDS activity and selectivity.     

Selective catalytic reduction of NO over metal oxide or noble metal-doped In2O3/Al2O3 catalysts by propene in the presence of oxygen

The activities of metal oxide CuO, SnO₂, CoO, Ag₂O, ZnO or noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts for selective catalytic reduction of NO by propene were investigated. The temperature windows for NO reduction over noble metal-doped In₂O₃/Al₂O₃ catalysts were shifted and broaden slightly compared with single component catalyst alone. This revised version was published online in June 2006 with corrections to the Cover Date.     

Effect of electron beam irradiation on CO2 reforming of methane over Ni/Al2O3 catalysts

The effect of electron beam irradiation on the CO₂ reforming of methane over Ni/Al₂O₃ was investigated. The conversion rate of CO₂ and CH₄ forming H₂ and CO using various catalysts irradiated with an absorbed dose greater than 2 MGy was 5–10% higher than when using an untreated catalyst. The Ni/O ratio on the catalyst surface increased after treatment with an electron beam, and was more prominent for catalysts with a higher Ni content. As such, based on XRD and XPS measurements, electron beam treatment was found to result in either the desorption of oxygen from NiO or the removal of OH groups from the outermost surface layer of the catalyst. In addition, the concentration of active sites, such as Ni²⁺ and NiO, or surface defects was also found to increase with the absorbed radiation dose, thereby increasing the conversion rate.     

氧化铝载体硫酸化对锰铈催化剂SCR脱硝性能的影响

分别以硫酸改性前后的氧化铝为载体,采用浸渍法制备了锰铈催化剂,对其NH_3-SCR脱硝性能进行评价,并采用XRD、BET、NH_3-TPD、H_2-TPR以及FT-IR对催化剂进行了表征。结果表明,改性降低了金属的分散性和氧化性,增加了酸量,特别是B酸量;催化剂的最佳脱硝温度窗口向高温扩展,活性温度窗口范围变宽,并且,改性液浓度越大变化幅度越大。当反应温度在200-250℃时,未改性催化剂与采用0.2 mol/L硫酸改性的催化剂具有接近的催化活性,但改性后的催化剂具有更高的抗水抗硫活性,250℃时脱硝率可达70%。     

Photocatalytic conversion of NOx on AgCl/Al2O3 catalyst

The rate of NO conversion under UV illumination was evaluated over Ag/Al₂O₃ and AgCl/Al₂O₃ catalysts at room temperature. The AgCl/Al₂O₃ catalyst is highly active for the conversion of NO_x. The conversion is enhanced in the presence of O₂ and further enhanced when oxygen coexists with hydrocarbons. Diffuse reflectance spectra of AgCl/Al₂O₃ and Ag/Al₂O₃ show an absorption band at 250 nm, and a weak and broad band at 230 nm, respectively. The high photocatalytic NO_x conversion is achieved over the AgCl/Al₂O₃ catalyst. The conversion level of NO_x is maintained above 60% over 5 h in the presence of O₂ and hydrocarbons under UV-irradiation. The absorption band at 250 nm is ascribed to the band gap energy of crystallized AgCl particles on Al₂O₃. These results suggest that high photocatalytic NO_x conversion proceeds on crystallized AgCl particles formed on Al₂O₃.     

TPR studies on steam reforming of 2-propanol on Rh/Al2O3, Ru/Al2O3 and Pd/Al2O3

Reaction pathways for steam reforming of 2-propanol (isopropyl alcohol, IPA) on Rh/Al₂O₃, Ru/Al₂O₃ and Pd/Al₂O₃ have been studied by temperature-programmed reactions (TPRs) of IPA and acetone in the presence of steam. The results of TPRs suggest that that of IPA on Rh/Al₂O₃ and Ru/Al₂O₃ proceeds via acetone, while the steam reforming of IPA on Pd/Al₂O₃ takes place via propene from acetone. This revised version was published online in August 2006 with corrections to the Cover Date.     

Preparation and characterization of MgO/Al2O3 mixed oxides support for hydrotreating catalysts

The characteristics of pure MgO, Al₂O₃ and three binary mixtures of MgO-Al₂O₃ were studied by determining their BET surface areas, micropore surface area, total pore volume, adsorption-desorption isotherms, the x-ray diffractogram, surface acidity and catalytic functionality for cumene cracking.The XRD results show that the incorporation of alumina into the magnesia beyond 50% renders it amorphous. Furthermore, the mixed oxide containing 50% magnesia and 50% alumina had the highest BET surface area of 200 m²/g and is the only mixed oxide with bimodal pores.The results of the acidity measurements and cumene cracking functionality indicates that strong acid sites are found only in mixed oxides containing more than 50% alumina.     

Effect of Al2O3 Binder on the Precipitated Iron-Based Catalysts for Fischer-Tropsch Synthesis

A series of iron-based Fischer-Tropsch synthesis (FTS) catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduc-tion/desorption (TPR/TPD) and Mossbauer effect spectroscopy (MES) methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 (weight basis). After the point, it decreases with further increase in Al2O3 content. The incorporation of AI2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor (CSTR) under the reaction conditions of 260℃, 1.5 MPa, 1000 h-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction (WGS) activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.