聚丙撑碳酸酯的流动性能

聚丙撑碳酸酯的流动性能王胜杰，黄玉惠，丛广民（中国科学院广州化学研究所广州５１０６５０）关键词聚丙撑碳酸酯，流动性能，表观粘度，粘均分子量聚丙撑碳酸酯（ＰＰＣ）是由二氧化碳和环氧丙烷共聚而成的新型含端羟基脂肪族聚碳酸酯［１］，作为对它的基本表征之一，...     

聚丙撑碳酸酯的辐射效应

研究了室温条件下聚丙撑碳酸酯(PPC)在钴-60和电子加速器辐照过程中的响应行为。结果表明,聚丙撑碳酸酯是一种辐射裂解型聚合物,其分子量随着辐射剂量的增加而减小。1mm厚PPC片材在室温和N2气保护条件下,其裂解G值为Gs,γ-ray=10.81;Gs,EB=4.9。不同的裂解G值表明,O2气在聚丙撑碳酸酯的辐射裂解过程中有重要影响。红外光谱研究表明,辐射后聚丙撑碳酸酯在3474cm-1处的峰宽峰高增加,表明其裂解后端—OH基增加。由于裂解作用,辐射后聚丙撑碳酸酯的抗张强度和断裂伸长率均下降。在通常的辐射消毒剂量范围内(25~50kGy),PPC的保留抗张强度大于23MPa,断裂伸长率大于4%,裂解后试样的力学性能依然能够满足实际应用需要,因此PPC可以经受辐射消毒。     

偶联剂对聚氯乙烯－聚丙撑碳酸酯共混体系力学性能的影响

偶联剂对聚氯乙烯－聚丙撑碳酸酯共混体系力学性能的影响王胜杰，黄玉惠，丛广民（中国科学院广州化学研究所广州５１０６５０）关键词聚氯乙烯，聚丙撑碳酸酯，偶联剂，丁腈胶，过氧化苯甲酰，共混聚氯乙烯（ＰＶＣ）是用量巨大的通用塑料，其软性制品需用大量的增塑剂，...     

PPC/SBR并用弹性体的配方选择

利用正交法对丁苯橡胶（SBR）／聚丙撑碳酸酯（PPC）共混弹性体进行配方设计，得到了一个具有良好综合性能的配方。并通过方差分析得出PPC含量和马来酸酐（MA）用量是影响弹性体拉伸性能的最显著因素。     

交联助剂对PPC／NBR弹性体结构和性能的影响

研究了马来酸酐（ＭＡ）及异氰脲酸三烯丙酯（ＴＡＩＣ）对聚丙撑碳酸酯／丁腈橡胶共混弹性体结构和性能的影响，发出加入ＭＡ或ＴＡＩＣ能有效地改善交联网络；加入适量ＭＡ能显著改善共混弹性体热氧老化稳定性；加入ＴＡＩＣ使共混弹性体具有优良的高弹特性和力学性能。     

氯化聚丙撑碳酸酯增容聚丙撑碳酸酯/秸秆粉复合材料的制备及性能

聚丙撑碳酸酯(PPC)是一种新型热塑性生物降解材料,但其热性能及力学性能较差,应用受到限制。以秸秆粉这种农作物副产品作为增强体改性PPC,既可以提高PPC的力学性能同时又可开发利用秸秆资源。氯化聚丙撑碳酸酯(CPPC)是聚丙撑碳酸酯(PPC)经过氯化得到的,对天然纤维表面具有良好的浸润性和粘结性。本文以CPPC为增容剂,通过熔融共混法制备了PPC/秸秆粉复合材料。采用扫描电子显微镜(SEM)、拉伸实验、动态力学性能测试(DMA)及转矩流变仪对复合材料的结构及性能进行了表征,重点考察了CPPC的添加量对复合材料力学和流变性能的影响。结果表明,当CPPC质量分数为1.8%时,可使添加质量分数为30%秸秆粉的PPC复合材料拉伸强度提高38%,模量提高30%。同时,CPPC的引入使复合材料的粘度下降,改善了PPC/秸秆粉复合材料的加工性能。因此,作为增容剂的CPPC为制备高性能PPC/天然纤维复合材料提供了新的解决办法。     

聚丙撑碳酸酯／环氧树脂体系的力学性能

研究了聚丙撑碳酸酯／环氧树酯固化产物的动态力学性能和力学性能，考察了ＰＰＣ的分子量、含量对力学谱和力学性能的影响．结果表明，随ＰＰＣ含量增加，ｔａｎδ半峰宽增加，ＰＰＣ含量在２０～３０份时力学性能达最佳值，ＰＰＣ的分子量对力学性能的影响不大，但对动态力学和相区尺寸稍有影响。     

三元共聚物聚甲基乙撑-环己撑碳酸酯的合成与表征

报道了三元共聚物聚甲基乙撑-环己撑碳酸酯的制备与性能研究. 实验采用高活性的负载戊二酸锌作为催化剂, 在不添加任何溶剂的情况下, 以二氧化碳和环氧丙烷、环氧环己烷为原料, 制备了不同环己撑碳酸酯含量的三元共聚物, 并对其结构和热性能、力学性能进行了表征和分析. 结果表明这些三元共聚物具有较高的分子量, 且玻璃化转变温度随着主链上的环己撑碳酸酯含量增加而逐渐升高. 同时三元共聚物表现出比二元共聚物更好的力学性能.     

聚乙烯基撑碳酸酯和聚羟基甲撑的合成与表征

通过乙烯基撑碳酸酯的聚合制得了无色透明的高分子量的聚合物，再经水解制得了聚羟基甲撑膜和粉状物，研究了在丙酮和二甲基甲酰胺中聚乙烯基撑碳酸酯的降解机理。     

聚丙撑碳酸酯增韧环氧树脂的研究

研究了聚丙撑碳酸酯（ＰＰＣ）对环氧树脂（ＥＰ）的改性作用、加入２０～３０Ｐｈｒ的ＰＰＣ，环氧树脂力学性能可以大幅度提高，粘接剪切强度为１２３３ＭＰａ，冲击强度为１６．７８ｋＪ／ｍ２；而纯环氧树脂固化物，其剪切强度为９．３６ＭＰａ，冲击强度为９．９９ｋＪ／ｍ２。ＳＥＭ和ＤＳＣ观测表明ＰＰＣ／ＥＰ体系呈两相结构。     

Thermal,mechanical and rheological properties of biodegradable poly(propylene carbonate) and poly(butylene carbonate) blends

Poly(propylene carbonate)(PPC) was melt blended in a batch mixer with poly(butylene carbonate)(PBC) in an effort to improve the toughness of the PPC without compromising its biodegradability and biocompatibility. DMA results showed that the PPC/PBC blends were an immiscible two-phase system. With the increase in PBC content, the PPC/PBC blends showed decreased tensile strength, however, the elongation at break was increased to 230% for the 50/50 PPC/PBC blend. From the tensile strength experiments, the Pukanszky model gave credit to the modest interfacial adhesion between PPC and PBC, although PPC/PBC was immscible. The impact strength increased significantly which indicated the toughening effects of the PBC on PPC. SEM examination showed that cavitation and shear yielding were the major toughening mechanisms in the blends subjected the impact tests. TGA measurements showed that the thermal stability of PPC decreased with the incorporation of PBC. Rheological investigation demonstrated that the addition of PBC reduced the value of storage modulus, loss modulus and complex viscosity of the PPC/PBC blends to some extent. Moreover, the addition of PBC was found to increase the processability of PPC in extrusion. The introduction of PBC provided an efficient and novel toughened method to extend the application area of PPC.     

水辅助加工法制备聚丙撑碳酸酯/淀粉共混物

分别采用普通熔融共混法和水辅助加工法,制备了具有不同共混形态的聚丙撑碳酸酯(PPC)/淀粉共混物,并研究了淀粉分散形态对共混物的玻璃化转变温度(Tg)、流变以及力学性能的影响。研究结果表明,采用普通熔融共混法时,淀粉未发生糊化,并以原颗粒状分散于基体中;而采用水辅助加工法时,淀粉发生糊化,并在挤出过程中原位形成纤维结构。当淀粉以纤维形式分散于PPC基体中时,其与PPC间的界面接触面积显著增加,二者的相互作用增强,PPC/淀粉共混物的Tg、储能模量以及复合黏度显著提高。力学性能测试结果表明,当淀粉质量分数为30%,采用水辅助加工法制备的PPC/淀粉共混物的拉伸模量相比于纯PPC提高了67.7%。     

Thermal,Mechanical and Rheological Properties of Eco-friendly Poly（propylene carbonate）/Poly（1,2-propylene succinate） Blends

In order to improve the flexibility of poly（propylene carbonate） （PPC）, poly（1,2-propylene succinate） （PPSu） was used to plasticize PPC in a batch mixer. The effects of PPSu on the miscibility, thermal stability, mechanical and theological properties of the blends were investigated. PPC was partially miscible with PPSu. It was demonstrated that PPSu decreased the glass transition temperature and melt viscosity of PPC, as shown in the DSC and rheological curves. With the increase in PPSu content, the PPC/PPSu blends showed decreased tensile strength, however, the elongation at break was increased to 1100% for the 70/30 PPC/PPSu blend. The introduction of PPSu provided an efficient and novel plasticization method to extend the application area of PPC.     

Biodegradable Foaming Material of Poly(butylene adipate-co-terephthalate) (PBAT)/Poly(propylene carbonate) (PPC)

A biodegradable blend foaming material of poly(butylene adipate-co-terephthalate)(PBAT)/poly(propylene carbonate)(PPC)was successfully prepared by chemical foaming agent and screw extrusion method.First,PBAT was modified by bis(tert-butyl dioxy isopropyl)benzene(BIBP)for chain extension,and then the extended PBAT(E-PBAT)was foamed with PPC using a twin(single)screw extruder.By analyzing the properties of the blends,we found that Young’s modulus increased from 58.8 MPa of E-PBAT to 244.7 MPa of E-PBAT/PPC 50/50.The viscosity of the polymer has a critical influence on the formation of cells.Compared with neat PBAT(N-PBAT),the viscosity of E-PBAT increased by 3396 Pa·s and E-PBAT/PPC 50/50 increased by 8836 Pa·s.Meanwhile,the dynamic mechanical analysis(DMA)results showed that the storage modulus(E’)at room temperature increased from 538 MPa to 1650 MPa.The various phase morphologies(“sea-island”,“quasi-co-continuous”and“cocontinuous”)and crystallinity of the blends affected the spread velocity of gas and further affected the foaming morphology in E-PBAT/PPC foam.Therefore,through the analysis of phase morphology and foaming mechanism,we concluded that the E-PBAT/PPC 70/30 component has both excellent strength and the best foaming performance.     

Thermal,Rheological and Mechanical Properties of Biodegradable Poly(propylene carbonate)/Epoxidized Soybean Oil Blends

Biodegradable poly(propylene carbonate)(PPC)/epoxidized soybean oil(ESO) blends with different component ratios were prepared by melt blending to improve the performance of PPC. The phase morphology, thermal properties, rheological properties and mechanical properties of the blends were investigated in detail. SEM examination revealed good interfacial adhesion between PPC matrix and ESO.According to DSC and DMA, as the content of ESO increased, the glass transition temperature of the PPC compone...     

Mechanical,thermal and rheological properties and morphology of poly (lactic acid)/poly (propylene carbonate) blends prepared by vane extruder

In this study, the poly (lactic acid) (PLA) and poly (propylene carbonate) (PPC) blends with different compositions were prepared by a novel vane extruder based on elongation rheology. The mechanical properties, morphologies, crystallization behavior, thermal stability, and rheological properties of the blends were investigated. Mechanical test showed that PLA could be toughened by PPC to some extent, and the impact strength of the PLA was maximized when PPC content was about 30%. Differential scanning calorimetry analysis revealed that PPC had little effect on the melting process, the crystallization behavior of PLA component in the blend was improved, and the cold crystallizability of PLA decreased with the increase of PPC content when the PPC content was less than 50%. Thermogravimetry analysis showed that the thermal stability of the blends was improved by compounding with PLA. Scanning electron microscope showed that the dispersion of PLA droplets in PPC matrix was better than that of PPC droplets in PLA matrix. Rheological test showed that the melt viscosity of the pure PLA and the blend with 10% PPC was insensitive to shear rate, and the blends melt appeared shear thinning phenomenon with the increase of PPC content. It also showed that the blends microstructure changed with the addition of PPC and the blends with PPC content in a certain range had similar stress relaxation mechanism. Copyright © 2016 John Wiley & Sons, Ltd.     

煤加氢液化残渣的流变特性研究

采用从煤直接液化实验装置取得的液化残渣,研究了它的流变性及温度和油、沥青质、固体含量对其流变性的影响。液化残渣是剪切变稀的非牛顿型假塑性流体,非牛顿指数随温度升高而不断减小,温度越高越接近牛顿流体行为。液化残渣对温度非常敏感,在升温过程中其表观黏度下降很快,且没有出现黏度峰。在液化残渣中加入少量的循环油后其表观黏度大幅下降;而在加入少量沥青质后则表现出低温下黏度变大,高温下黏度变小的现象;固体含量则始终是黏度增大的因素,表明其黏度与油、沥青质和固体含量关系密切。液化残渣的黏度－温度关系符合Arrhenius关系式,但在升温过程中出现了拐点,低温段的黏流活化能比高温段的要大。     

褐藻酸钠溶液的超声辐照效应及其对分子量参数的影响

观察了超声辐照过程中褐藻酸钠溶液的pH值、温度、表现特性粘度和表现分子量及其分布的变化,发现在超声辐照过程中,褐藻酸钠的表现平均分子量经历了下降→回升→再下降的过程;当超声辐照停止后,表现特性粘度和表观平均分子量又略有回升,因而推测在这一过程中褐藻酸钠的构象可能发生了变化。