Investigation of the energy resolution with a RETGEM detector

A novel Micro-pattern gaseous detector (MPGD), thick GEM with electrodes made of a resistive material (RETGEM) is presented. In this paper we mainly investigate the energy resolution of a RETGEM in Ar+CO_2 with different gas mixtures. The results indicate that an energy resolution 30% in single and double mode can be obtained. The existence of an optimum energy resolution is discussed.     

Investigation of add-back effects in a segmented Clover detector

The resolution and the summing characteristics of an EXOGAM segmented Clover germanium detector has been studied for use it in γ spectroscopic experiments. The measurements have been performed with standard radioactive sources of 152Eu, 133Ba and β-delayed γ-rays from 176Ir decay. The data analytic results, realized by software, are presented in this paper.     

Investigation of add-back effects in a segmented Clover detector

The resolution and the summing characteristics of an EXOGAM segmented Clover germanium detector has been studied for use it in y spectroscopic experiments. The measurements have been performed with standard radioactive sources of ^152Eu, ^133Ba and β-delayed γ-rays from 176Ir decay. The data analytic results, realized by software, are presented in this paper.     

溴化镧探测器时间分辨率的测量

用60 Coγ源和搭建的电子学测量系统,测量了自制塑料闪烁探测器、3英寸的溴化镧探测器和电子学系统的时间分辨率,得到了圣戈班公司生产的3英寸溴化镧探测器的时间分辨率为(283.2±0.9)ps.     

Investigation of GEM-Micromegas detector on X-ray beam of synchrotron radiation

To reduce the discharge of the standard bulk Micromegas and GEM detectors, a GEM-Micromegas detector was developed at the Institute of High Energy Physics. Taking into account the advantages of the two detectors, one GEM foil was set as a preamplifier on the mesh of Micromegas in the structure and the GEM preamplification decreased the working voltage of Micromegas to significantly reduce the effect of the discharge. At the same gain, the spark probability of the GEM-Micromegas detector can be reduced to a factor 0.01 compared to the standard Micromegas detector, and an even higher gain could be obtained. This paper describes the performance of the X-ray beam detector that was studied at 1W2B Laboratory of Beijing Synchrotron Radiation Facility. Finally, the result of the energy resolution under various X-ray energies was given in different working gases. This indicates that the GEM-Micromegas detector has an energy response capability in an energy range from 6 keV to 20 keV and it could work better than the standard bulk-Micromegas.     

Investigation of GEM-Micromegas detector on X-ray beam of synchrotron radiation

To reduce the discharge of the standard bulk Micromegas and GEM detectors, a GEM-Micromegas detector was developed at the Institute of High Energy Physics. Taking into account the advantages of the two detectors, one GEM foil was set as a preamplifier on the mesh of Micromegas in the structure and the CEM pream- plification decreased the working voltage of Micromegas to significantly reduce the effect of the discharge. At the same gain, the spark probability of the GEM-Micromegas detector can be reduced to a factor 0.01 compared to the standard Micromegas detector, and an even higher gain could be obtained. This paper describes the performance of the X-ray beam detector that was studied at 1W2B Laboratory of Beijing Synchrotron Radiation Facility. Finally, the result of the energy resolution under various X-ray energies was given in different working gases. This indicates that the GEM-Micromegas detector has an energy response capability in an energy range from 6 keV to 20 keV and it could work better than the standard bulk-Micromegas.     

Time resolution of the bunch-shape detector with a thin-wire emission target

The time resolution of a new bunch-length detector based on the radio frequency (RF) scanning of the produced secondary electrons is calculated. A dedicated Monte-Carlo code by means of SIMION software is developed for accurate simulation of spread in the investigated secondary electrons transit times and image width. In calculation the initial energy distribution of electrons and the actual structure of accelerating and focusing electric fields were considered. It is shown that by using a thin-wire emission target a femtosecond time precision could be achieved using moderate applied voltages.     

Micromegas探测器计数曲线、增益以及能量分辨特性的研究

介绍了自行研制的Micromegas探测器的基本结构和工作原理. 在不同工作气体(Ar和CO₂)配比条件下,利用⁵⁵Fe放射源对该探测器的能量分辨、计数曲线和气体增益等特性进行了较为详尽的测试. 对相关结果进行了讨论. 关键词： Micromegas探测器 计数曲线 能量分辨率 增益     

Study of measuring methods on spatial resolution of a GEM imaging detector

In this paper, the limitations of the common method measuring intrinsic spatial resolution of the GEM imaging detector are presented. Through theoretical analysis and experimental verification, we have improved the common method to avoid these limitations. Using these improved methods, a more precise measurement of intrinsic spatial resolutions are obtained.     

Energy resolution of the CdTe‐XPAD detector: calibration and potential for Laue diffraction measurements on protein crystals

The XPAD3S‐CdTe, a CdTe photon‐counting pixel array detector, has been used to measure the energy and the intensity of the white‐beam diffraction from a lysozyme crystal. A method was developed to calibrate the detector in terms of energy, allowing incident photon energy measurement to high resolution (approximately 140 eV), opening up new possibilities in energy‐resolved X‐ray diffraction. In order to demonstrate this, Laue diffraction experiments were performed on the bending‐magnet beamline METROLOGIE at Synchrotron SOLEIL. The X‐ray energy spectra of diffracted spots were deduced from the indexed Laue patterns collected with an imaging‐plate detector and then measured with both the XPAD3S‐CdTe and the XPAD3S‐Si, a silicon photon‐counting pixel array detector. The predicted and measured energy of selected diffraction spots are in good agreement, demonstrating the reliability of the calibration method. These results open up the way to direct unit‐cell parameter determination and the measurement of high‐quality Laue data even at low resolution. Based on the success of these measurements, potential applications in X‐ray diffraction opened up by this type of technology are discussed.     

能量响应平坦的康普顿探测器设计

以开展能量响应平坦的真空康普顿探测器为目的,采用厚薄材料叠加补偿设计思想,使用蒙特卡罗方法,对真空康普顿探测器的灵敏度能量响应进行了优化设计。优化的探测器系统采用0.01,1.00 mm厚Au叠加的发射极,3 mm厚Fe前窗以及3 mm挡铅。在f40 mm准直下,实现了在0.4~7.0 MeV 能区内,探测器本征灵敏度极值变化小于10.7%。该能量响应平坦性优于当前各种常见的探测器。     

基于单矢量差分能量检测器的扩频水声通信

通过获得扩频处理增益, 直接序列扩频水声通信系统具有较高的稳定性, 是高质量水声通信及远程水声通信的首选通信方式. 但复杂的海洋环境使得直扩系统在解扩时受到载波相位跳变的影响, 这将导致直扩系统的扩频处理增益下降. 为此, 本文针对直扩系统提出了差分能量检测器算法, 通过比较接收端相关器输出能量完成解码, 并与有源平均声强器算法相结合, 提出单矢量差分能量检测器算法. 该算法具有很好的抗载波相位跳变和多途扩展干扰的能力, 并可对信号方位信息实时跟踪估计, 利用估计方位进行矢量组合可获得矢量处理增益, 从而保证直扩系统可以在低信噪比、时变信道条件下稳定工作. 通过仿真分析和大连海试试验, 验证了本文提出的单矢量差分能量检测器算法的有效性和稳健性.     

The analysis of the integral gated mode single photon detector

This paper critically analyses and simulates the circuit configuration of the integral gated mode single photon detector which is proposed for eliminating the transient spikes problem of conventional gated mode single photon detector. The relationship between the values of the circuit elements and the effect of transient spikes cancellation has been obtained. With particular emphasis, the bias voltage of the avalanche photodiode and the output signal voltage of the integrator have been calculated. The obtained analysis results indicate that the output signal voltage of the integrator only relates to the total quantity of electricity of the avalanche charges by choosing the correct values of the circuit elements and integral time interval. These results can be used to optimize the performance of single photon detectors and provide guides for the design of single photon detectors.     

Measurement of X-ray photon energy and arrival time using a silicon drift detector

Detecting the X-ray emission of pulsars and obtaining the photons' time of arrival are the foundational steps in autonomous navigation via X-ray pulsar measurement. The precision of a pulse's time of arrival is mainly determined by the precision of photon arrival time measurement. In this work, a silicon drift detector is used to measure photon energy and arrival time. The measurement system consists of a signal detector, a processing unit, a signal acquisition unit and a data receiving unit. This system acquires the energy resolution and arrival time information of photons. In particular, background noise with different energies disturbs pulse profile forming, the system can also achieve a high signal-to-noise ratio profile. Ground test results show that this system can be applied in autonomous navigation based on X-ray pulsar measurement.     

Performance of a superconducting single photon detector with nano-antenna

<正>The performance of single-photon detectors can be enhanced by using nano-antenna.The characteristics of the superconducting nano-wire single-photon detector with cavity plus anti-reflect coating and specially designed nanoantenna is analysed.The photon collection efficiency of the detector is enhanced without damaging the detector’s speed,thus getting rid of the dilemma of speed and efficiency.The characteristics of nano-antenna are discussed,such as the position and the effect of the active area,and the best result is given.The photon collection efficiency is increased by 92 times compared with that of existing detectors.     

A stopping layer concept to improve the spatial resolution of gas-electron-multiplier neutron detector

In recent years, gas electron multiplier (GEM) neutron detectors have been developing towards high spatial resolution and high dynamic counting range. We propose a novel concept of an Al stopping layer to enable the detector to achieve sub-millimeter (sub-mm) spatial resolution. The neutron conversion layer is coated with the Al stopping layer to limit the emission angle of ions into the drift region. The short track projection of ions is obtained on the signal readout board, and the detector would get good spatial resolution. The spatial resolutions of the GEM neutron detector with the Al stopping layer are simulated and optimized based on Geant4GarfieldInterface. The spatial resolution of the detector is 0.76 mm and the thermal neutron detection efficiency is about 0.01% when the Al stopping layer is 3.0 μ m thick, the drift region is 2 mm thick, the strip pitch is 600 μ m, and the digital readout is employed. Thus, the GEM neutron detector with a simple detector structure and a fast readout mode is developed to obtain a high spatial resolution and high dynamic counting range. It could be used for the direct measurement of a high-flux neutron beam, such as Bragg transmission imaging, very small-angle scattering neutron detection and neutron beam diagnostic.     

The correlation of the energy resolution of incident light with the measured reflectance of multilayers

This paper presents an expression for describing the correlation of the energy resolution of incident light with the measured reflectance of multilayers, and gives a new method for calculating the polychromatic-light reflectance of multilayers. Using this method we give the reflectance spectrum of some multilayers in the case in which the incident light is polychromatic. The theoretical analysis shows that for the multilayers of a given design the peak reflectance of the polychromatic light is smaller than that of the monochromatic light, but no-peak reflectance of the polychromatic light is bigger than that of the monochromatic light. Further, the measured reflectance spectrum will be a line if the energy resolution is less than a decided value. The shorter the design-wavelength of the multilayer, the stronger the effect of the energy resolution on the reflectance.     

Experimental study of a THGEM detector with mini-rims

The gas gain and energy resolution of single and double THGEM detectors (5 cm×5 cm effective area) with mini-rims (rim less than 10 μm) were studied. The maximum gain was found to reach 5×10³ and 2×10⁵ for single and double THGEMs respectively, while the energy resolution for 5.9 keV X-rays varied from 18% to 28% for both single and double THGEM detectors of different hole sizes and thicknesses. Different combinations were also investigated of noble gases (argon, neon) mixed with a quantity of other gases (isobutane, methane) at atmospheric pressure.     

CdZnTe像素探测器的电输运性能

碲锌镉(CdZnTe)是一种性能优异的室温核辐射半导体探测器材料,广泛应用于核安全、核医学以及空间科学等领域.然而,传统的CdZnTe平面探测器受制于"空穴拖尾"效应的影响,探测性能有待改善.采用改进的垂直布里奇曼法生长的In掺杂Cd_(0.9)Zn_(0.1)Te单晶制备出单载流子收集的4×4像素阵列探测器,通过电流-电压(I-V)测试和γ射线能谱响应测试,研究了像素探测器的电学性能和载流子电输运性能,随之与相应的CdZnTe平面探测器进行了性能对比.结果表明,CdZnTe像素探测器的电阻率约为1.73×10~(10)?·cm,且施加100 V偏压后单像素点的最大漏电流小于2.2 nA;当施加偏压升高至300 V时,单像素点对~(241)Am@59.5 keV的γ射线的最佳能量分辨率可达5.78%,探测性能优于相同条件下制备的CdZnTe平面探测器.     

MCT探测器Franz-Keldysh效应有效强度的一种表征方法

通常只有使用较为昂贵、精密的实验设备才能获得 MCT探测器响应波长的偏移量 ,才可确定 MCT探测器 Franz- Keldysh(以下简写为 F- K)效应的强度。提出一种表征 MCT探测器 F- K效应有效强度的简易方法 ,即用 MCT探测器在零偏压及反偏压时的输出电压比来表征其 F- K效应有效强度的强弱。实验结果证实了这种方法有效、可行。