固相缩聚PET等温结晶动力学

高聚物等温结晶动力学方面的研究者甚多,由熔融缩聚制备的不同分子量PET的等温结晶动力学及几种不同缩聚催化体系固相缩聚PET的等温结晶动力学已有报道.本文采用一个修正的Avrami方程对固相缩聚PET样品进行系统的等温结晶动力学研究.     

Crystallization behavior and morphology of PE-g-LCP copolymers

 This study presents DSC and optical microscopy investigations on copolymers of semiflexible liquid crystalline polymer SBH 112 grafted to functionalized low molecular mass polyethylene (PEox) obtained by melt polycondensation or reactive blending procedures. The crystallization behavior of the PE-g-SBH copolymers has been studied under non-isothermal measurement conditions carried out at different cooling rates. The crystallization temperature (T _cr) of the PE component of the copolymers decreases steadily upon increasing the concentration of the SBH grafts. It was found that the copolymers prepared by reactive blending crystallize at slightly higher T _cr than those prepared by polycondensation and with a higher rate, confirmed by the determination of the crystallization rate coefficients (CRC). The results have been interpreted by the fact that the PE crystallizable segments and SBH grafts of the copolymers obtained by reactive blending are longer than those of the copolymers prepared by polycondensation. The overall nonisothermal crystallization kinetics has been studied by the Harnisch and Muschik equation. The results show that the mechanism of the crystallization of the PE phase changes only when the SBH content overruns ca.50%, due to the decrease of both nucleation and crystal growth rates. The morphology of the copolymers crystallized nonisothermally from melt has been examined by polarization microscopy. Fairly homogeneous morphology with tiny PE spherulites is observed for PE-g-SBH copolymers prepared by polycondensation with SBH as the minor phase. No sign of the dispersed LCP domains can be recognized. On the contrary, the morphology of the copolymers prepared by reactive blending is distinctly biphasic. The allegedly longer PE segments crystallize into tiny spherulites too, but the LC domains formed by the long SBH branches present in this type of copolymers appear clearly in the micrographs at room temperature. It is concluded that the copolymers prepared by reactive blending would be more effective as compatibilizers for PE/SBH blends than those prepared by polycondensation. Received: 9 October 1996 Accepted: 13 January 1997     

磷酸三苯酯对聚对苯二甲酸乙二酯结晶速率的影响

用光学退偏振法和DSC方法研究了聚合过程的助剂磷酸三苯酯(TPP)对聚对苯二甲酸乙二酯(PET)结晶速率的影响。用熔融混入办法将磷酸三苯酯加入PET中,不能降低PET在靠近T_g的低温结晶区的结晶速率。TPP对PET结晶速率影响的特点表明它不是PET的成核剂,而是一个增塑剂。加入TPP后样品的结晶速率可根据T_m和T_g的移动,从纯PET的结晶速率来预测。     

聚对苯二甲酸乙二醇酯/聚乙二醇醚插层嵌段共聚物的结晶性能

合成了不同用量、不同分子量的聚乙二醇醚(PEG)或聚丁二醇醚(PTMC)与聚对苯二甲酸乙二醇酯(PET)/蒙脱土(MMT)的嵌段共聚物。研究了MMT在共聚物中的分散状态及PEG或PTMG对PET/MMT插层聚合物结晶性能的影响。结果表明,MMT在共聚物中以纳米尺寸分散;加入PEG或PTMG增强了聚酯链段的柔顺性,使共聚物熔体降温过程的结晶温度提高,冷结晶温度降低,即插层嵌段共聚物的结晶速率提高;在合成的共聚物中,分子量为2000,用量为DMT的6%的PEG对插层共聚物结晶速率的促进作用最大     

Structure investigations of PE-g-LCP copolymers

 Transesterification products – copolymers of semiflexible liquid crystalline polymer SBH 112 grafted to functionalized low molecular mass polyethylene (PEox) obtained by melt polycondensation or reactive blending procedures have been investigated by wide-angle x-ray scattering (WAXS) and scanning electron microscopy (SEM). The x-ray diffraction patterns of PE-g-LCP copolymers obtained via both procedures consist of reflections typical for the orthorhombic crystalline lattice of PE and the single reflection of the solid LCP. The lack of d _hkl variations with respect to those of neat PEox and SBH indicates the absence of interactions in the crystalline phase or that of cocrystallization phenomena between the components of the PE-g-SBH copolymers. The analysis of the crystallinity degree and normalized amorphous and crystalline contributions to the diffraction patterns of the products suggests that both copolymer components are partly miscible in the amorphous phase. The extent of miscibility depends on the copolymer structure, namely on the length of PE segments and SBH grafts. PE segments in PE-g-SBH copolymers obtained by the reactive blending are longer and exhibit a higher crystallizability than those obtained via melt polycondensation. SBH grafts of the copolymers obtained by the reactive blending are also longer than those in the products obtained via melt polycondensation. The morphology of the samples has been interpreted as determined by the different structure of the copolymers obtained by both procedures. Received: 3 April 1996 Accepted: 15 August 1996     

New Technology for Solid-state Polymerization of Polymers: Polyethylene terephthalate–Solid-state Polyaddition

This article introduces the new M&G technology for Solid state polyaddition (SSPA) of polyethylene terephthalate (PET). The new SSPA is characterized by the following: (1) It is based on a novel chemical process, SSPA. (2) It is suitable for high-performance polyesters. (3) It enables separate control of many different key properties of the polyester (molecular weight, rheology, crystallinity, etc.). This intrinsic flexibility has already been exploited to produce tailor-made polyesters suitable for most important applications in packaging and related fields. It is also a powerful tool for the upgrading of recycled PET. The SSPA reaction has a much faster kinetic than the standard solid-state upgrading process so that accordingly the intrinsic viscosity (I.V.) built up in the solid state is much faster than that of solid-state polycondensation. This raises the possibility of solid-state upgrading at lower temperatures, where standard solid-state polycondensation reactions are barely noticeable. The accelerating reactions used in this process could be utilized to de-bottleneck the existing production plants in order to attain greater productivity, more flexibility, lower costs and higher quality. © 1997 John Wiley & Sons, Ltd.     

The formation of polyethylene terephthalate in the presence of dicarboxylic acids

The process of polyethylene terephthalate (PET) formation in the presence of dicarboxylic acids has been studied. Certain amounts of terephthalic acid (TPA) have two- to threefold accelerating efficiency in the polycondensation process. To elucidate the causes of the acceleration the main reactions leading to PET formation in the presence of dicarboxylic acids have been investigated by the use of models. The evaluation of kinetic and equilibrium parameters obtained for model reactions made it possible to conclude that the influence of carboxyl-containing additives on the apparent rate of polycondensation manifests itself in accelerating direct reactions and facilitating the liberation of the eliminated by-product; that is, ethylene glycol (EG) from the polymer melt. Carboxylic acid acts as a catalyst on the ester interchange of 2-hydroxyethyl ester end groups and thus increases the rate of polymer formation in this reaction 10–40 times. The parallel interaction between the 2-hydroxyethyl ester end group and the carboxyl group of the added acid is also catalyzed by the acid and its rate constant is four times larger than that of the catalytic polycondensation of 2-hydroxyethyl ester end groups. Unlike EG, the reaction water formed in the process is more readily removed from the reaction system and thus promotes the intensification of the process. In addition, the carboxyl groups react with the eliminated EG to decrease its amount and shift the equilibrium toward polymer formation. The investigation of the consequent parallel reactions on models made it possible to draw a conclusion about the higher reactivity of 2-hydroxyethyl esters in the esterification processes. This fact has been explained by strengthening the nucleophilicity of the oxygen atom in the hydroxyl of a 2-hydroxyethyl ester group compared with that of EG; for example, by the formation of an intramolecular cycle involving a hydrogen bond. Simultaneously, it has been found that in the system simulating PET polycondensation in the presence of dicarboxylic acids the reaction mechanism involves the catalysis by a proton formed during the carboxyl group dissociation and accepted by the 2-hydroxyethyl ester group.     

SYNTHESIS AND PROPERTIES OF HIGH MOLECULAR WEIGHT POLY(LACTIC ACID) AND ITS RESULTANT FIBERS

Direct melt/solid polycondensation of lactic acid(LA)was carried out to obtain high molecular weight poly(lactic acid)(PLA)by a process using various catalysts in the first-step melt polycondensation,and followed solid polycondensation by using p-toulenesulfonic acid monohydrate(TSA)as the catalyst in the second step.Effects of various catalysts and reaction temperature on the molecular weight and crystallinity of resulting PLA polymers were examined.It was shown that SnCl_2·2H_2O/TSA,SnCl_2·2H_2O/succin...     

稀土催化体系催化PET固相缩聚的研究

研究了稀土催化体系对聚对苯二甲酸乙二酯固相缩聚反应的催化效果及对所得高分子量聚酯切片性能的影响,发现稀土催化体系可明显提高聚酯固相缩聚的反应速率,稀土催化体系对聚酯固相缩聚反应的催化活性明显高于传统催化体系,其中单一稀土催化体系与混合稀土催化体系在较低温度下具有相近的催化活性,而在较高温度下单一稀土催化体系的催化活性较高;加入稳定剂,不影响稀土催化的固相缩聚反应速率,稀土催化固相缩聚得到的PET样品具有较高的结晶度和较大的晶粒尺寸,其中单一稀土催化所得样品的晶粒尺寸最大,相应地,单一稀土催化的固相缩聚反应活化能也最大;稀土催化体系催化聚酯固相缩聚反应时添加适当稳定剂,可获得与采用传统催化体系得到的PET切片相近的热稳定性。     

Decoupling Study of Melt Polycondensation of Polycarbonate: Experimental and Modeling of Reaction Kinetics and Mass Transfer in Thin Films Polycondensation Process

During the melt polycondensation process of polycarbonate, reaction and mass transfer are deeply coupled owing to relatively high melt viscosity. In this work, the polycondensation reaction kinetics and mass transfer behavior of volatile phenol are decoupling studied in detail by using thin‐film experiments with 250–280 °C, 10–1000 Pa and 0.085–0.68 mm film thickness. A realistic apparent rate model coupled the reaction kinetics with thermodynamic equilibrium and diffusion behavior is developed to describe the polycondensation process, while the diffusion characteristic of small molecule (phenol) is further obtained based on penetration theory. The obtained polycondensation equilibrium constant ranges from 0.3 to 0.55, while the activation energy and pre‐exponential factor of temperature‐dependent diffusion coefficients of phenol are 87.9 kJ mol⁻¹ and 5.08 × 10² m² s⁻¹, respectively. It is also observed that the overall apparent rate of polycarbonate (PC) polycondensation process increases with higher temperature, lower pressure, and thinner film thickness. Coupling the reaction kinetics with mass transfer, the predictions of the realistic apparent rate model are in quite satisfactory agreement with experimental data.     

Synthesis of poly(glycolic acid‐alt‐12‐aminododecanoic acid): The thermal polymerization kinetics of sodium N‐chloroacetyl‐12‐aminododecanoate

A new regular poly(ester amide) consisting of glycolic acid and 12‐aminododecanoic acid was synthesized by a thermal polycondensation method involving the formation of a metal halide salt. Polymerization could start in liquefied or solid phases, depending on the reaction temperature. The polymerization kinetics were investigated by isothermal and nonisothermal isoconversional methods. The reaction model was selected with both Coats–Redfern and isokinetic relationships. The activation energy was higher when the reaction took place mainly in the solid state. A compensation effect was found between the frequency factor and the activation energy. The thermal properties of the new polymer were studied as well as the isothermal crystallization from the melt state. Melt‐grown spherulites were studied by means of polarizing optical microscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1199–1213, 2006     

Alternating oligo(p-phenylene vinylene)--perylene bisimide copolymers: synthesis,photophysics, and photovoltaic properties of a new class of donor--acceptor materials

A Suzuki polycondensation reaction has been used to synthesize two copolymers consisting of alternating oligo(p-phenylene vinylene) (OPV) donor and perylene bisimide (PERY) acceptor chromophores. The copolymers differ by the length of the saturated spacer that connects the OPV and PERY units. Photoinduced singlet energy transfer and photoinduced charge separation in these polychromophores have been studied in solution and in the solid state via photoluminescence and femtosecond pump-probe spectroscopy. In both polymers a photoinduced electron transfer occurs within a few picoseconds after excitation of the OPV or the PERY chromophore. The electron transfer from OPV excited state competes with a singlet energy transfer state to the PERY chromophore. The differences in rate constants for the electron- and energy-transfer processes are discussed on the basis of correlated quantum-chemical calculations and in terms of conformational preferences and folding of the two polymers. In solution, the lifetime of the charge-separated state is longer than in the films where geminate recombination is much faster. However, in the films some charges are able to escape from geminate recombination and diffuse away and can be collected at the electrodes when the polymers are incorporated in a photovoltaic device.     

Chain-growth polycondensation for well-defined condensation polymers and polymer architecture

The historical development of our research on polycondensation that proceeds in a chain-growth polymerization manner ("chain-growth polycondensation") for well-defined condensation polymers is described. We first studied polycondensation in which change of the substituent effect induced by bond formation drove the reactivity of the polymer end group higher than that of the monomer. In this approach, well-defined aromatic polyamides, polyesters, polyethers, and poly(ether sulfone)s were obtained. The second approach was the study of the phase-transfer polymerization of a solid monomer dispersed in an organic solvent. In this type of polymerization, the solid monomer was physically unable to react with another monomer and was carried with the phase transfer catalyst into the solution phase where it reacted with an initiator and the polymer end group in the solvent in a chain polymerization manner. We also found catalyst-transfer polycondensation as a third approach to chain-growth polycondensation. In the Ni-catalyzed polycondensation of 2-bromo-5-chloromagnesiothiophenes, the Ni catalyst transferred to the polymer end group, and a coupling reaction occurred there to yield a well-defined polythiophene. This chain-growth polycondensation was applied to the synthesis of condensation polymer architectures such as block copolymers, star polymers, graft copolymers, and so on.     

液晶嵌段共聚物PET/60PHB-b-PC的合成及结构与性能

采用ＰＥＴ齐聚物的原位乙酰化法通过加入少量乙二醇（ＥＧ）合成了端羟基液晶聚合物ＰＥＴ／６０ＰＨＢ，并将其作为大单体，与双酚Ａ及碳酸二苯酯通过熔融酯交换法，进一步制得了液晶嵌段共聚物ＰＥＴ／６０ＰＨＢ ｂ ＰＣ．研究了合成规律，并借助粘度测定、ＤＳＣ、偏光显微镜、Ｘ 光衍射和红外光谱分析等手段对合成的液晶嵌段共聚物进行了表征．研究表明，当ＰＥＴ齐聚物的ηｉｎｈ＝００５～００７ｄＬ／ｇ，Ａｃ２Ｏ／ＰＨＢ（ｍｏｌ／ｍｏｌ）＝１３，ＥＧ／ＰＥＴ（ｍｏｌ／ｍｏｌ）＝００６时能获得颜色、液晶性、溶解性均很好的端羟基液晶聚合物ＰＥＴ／６０ＰＨＢ，以此液晶聚合物为原料，采用合适的配方与工艺，能获得粘度较高、液晶性较好，并且熔体流动性很好的液晶嵌段共聚物ＰＥＴ／６０ＰＨＢ ｂ ＰＣ．通过偏光显微镜与Ｘ 光衍射观察，证明此嵌段共聚物呈现向列型液晶织构，但其液晶态织构与纯ＰＥＴ／６０ＰＨＢ、ＰＥＴ／６０ＰＨＢ和ＰＣ的混合物明显不同．此外，还初步建立了用红外的分析手段鉴定液晶聚合物ＰＥＴ／６０ＰＨＢ端基的方法．     

尼龙1010盐固态缩聚反应的研究

采用测定转化率和分子量、红外光谱、X-射线衍射分析、元素分析、偏光显微镜和扫描电镜等方法研究了结晶尼龙1010盐的特性、尼龙1010盐固态缩聚反应的动力学及其相应的晶体结构形态,用DSC法探讨了其反应机理。     

Matrix-assisted laser desorption/ionisation time-of-flight characterisation of biodegradable aliphatic copolyesters

Matrix-assisted laser desorption/ionisation time-of-flight (MALDI-TOF) and the off-line size exclusion chromatography matrix-assisted laser desorption/ionisation (SEC/MALDI) method has been applied to the structural characterisation and the molar mass (MM) determination of a series of biodegradable copolyesters synthesised by high temperature melt polycondensation reaction, and of two commercial copolyesters with the trade name Bionolle. The MALDI-TOF spectra of these copolymers showed the presence of cyclic oligomers in the lower mass region, in accord with expectations from polycondensation kinetics, and the presence of all linear species expected from their method of synthesis. The presence of unexpected linear species with olefin and carboxyl as end groups suggested the occurrence of undesirable thermal degradation processes during the melt polycondensation reaction. The absolute average molar masses obtained by the SEC-MALDI method turned out to be lower, by a factor of about two for succinate/adipate copolymers, and by a factor of three for succinate/sebacate copolymers, with respect to those computed by using polystyrene standards in SEC. Furthermore, the MALDI-TOF spectra of SEC fractions allowed not only the detection of linear and cyclic oligomers contained in these samples, but also the simultaneous determination of the average molar mass of both cyclic and linear oligomers. Due to the smaller hydrodynamic volume of cyclic chains with respect to linear ones, the ratio (M( cycle)/M( linear))( Ve) at a fixed elution volume was found to be 1.25, in good agreement with the theoretical value of 1.24. Copyright 2000 John Wiley & Sons, Ltd.     

芴-噁二唑类聚合物的合成及光谱特性

通过缩聚反应,制得了高分子量的线型和超支化的芴-噁二唑类聚合物．它们均可溶于常用的有机溶剂。在固态薄膜时,它们的紫外-可见光吸收光谱在大约398nm和376nm处有两个强的吸收峰。它们的薄膜PL光谱在蓝光波长范围内有强发射峰,薄膜PL效率约为16％。电化学测试显示它们的的LUMO能级比芴的均聚物高,而与钙、镁这样典型的阴极材料的功函数较接近．这表明此类聚合物具有较好的电子注入和传输性能。     

序列结构对液晶共聚酯性能的影响

本文通过熔融酯交换和Schottern-Baumann缩聚反应合成了两类组成相同而序列结构不同的基于对羟基苯甲酸、对苯二甲酸和二元酚的三元共聚酯,用热台偏光显微镜、DSC和X-射线衍射,较详细地研究了序列结构对液晶相类型、转变温度和固态结构等的影响。结果表明,无规共聚酯较规则共聚酯的熔化温度普遍降低;但序列结构的差异并不改变液晶相类型,规则共聚酯和无规共聚酯均为热致向列型液晶,两类共聚酯固态结构的差异可用结构单元的相似性进行解释。     

聚酰胺-聚ε-己内酯多嵌段共聚物合成、表征及反应动力学的研究

本文采用双羧基尼龙1010预聚物和双羟基聚δ-己内酯预聚物经熔融缩聚制得了不同嵌段链长度和不同软硬链段含量的尼龙1010-聚δ-己内酯多嵌段共聚物,并通过分子量(VPO)、核磁共振谱(¹HNMR)和热分析法(DSC)对该共聚物进行表征。同时,对尼龙1010和聚δ-已内酯熔融缩聚反应动力学作了研究。结果表明,该反应为二级反应,活化能为ΔΕ=58.2kcal/mol,反应常数K=1.36×10²²·e^-2.93×104/T。     

聚对苯二甲酸乙二醇酯切片的固相聚合规律

简要介绍了制备高分子量聚对苯二甲酸乙二醇酯的三种方法,重点介绍了其固相聚合的基本原理及主要副反应规律,固相聚合的各种影响因素,如预聚体原料路线、端羟基和羟基平衡、切片形状和尺寸、催化剂、反应副产物等。最后介绍了聚对苯二甲酸乙二醇酯固相滞反应动力学,如温度、时间对固相聚合反应速度的影响,低温固相聚合反应动力学等。