Poly(Methyl Red) Modified Glassy Carbon Electrodes: Electrosynthesis,Characterization, and Sensor Behavior

Poly(methyl red), PMR, was electropolymerized on glassy carbon electrodes by potential cycling in 50 mM phosphate buffer solution at pH 7.0 and 8.0 and Britton Robinson buffer solution in the pH range 7.0‐11.0. The electrochemical behavior of PMR modified electrodes was investigated by cyclic voltammetry in Britton Robinson buffer solution at different pHs from 5.0 to 10.0 and found that the best PMR film formation was obtained at pH 9.0. Uric acid was quantitatively determined at PMR modified electrodes by cyclic voltammetry and differential pulse voltammetry in Britton Robinson buffer at pH 5.0. Both methods presented a linear dependence between the anodic peak current and the concentration of uric acid in the range of 0.4 to 60 μM and 0.08 to 100 μM with the limits of detection of 0.038 and 0.009 μM for cyclic voltammetry and differential pulse voltammetry, respectively. Poly(methyl red) as redox mediator allowed the determination of uric acid without any interferences from the substances in serum samples.     

Electrochemical behaviour of sertraline at a hanging mercury drop electrode and its determination in pharmaceutical products

The electrochemical behaviour of sertraline at a hanging mercury drop electrode (HMDE) was described. Different voltammetric techniques, such as cyclic, linear sweep, differential pulse and square wave voltammetry, were used. Voltammograms were obtained at different pH values with a Britton-Robinson buffer solution used as supporting electrolyte. The best results were found by square wave voltammetry with electrodeposition at alkaline pH using a borate buffer with a pH = 8.2 for the samples, containing 12% (v/v) methanol. Under optimised conditions, a linear relationship between 2.33 x 10(-7) and 3.15 x 10(-6) M of sertraline with a limit of detection of 1.98 x 10(-7) M was obtained. The electrochemical method developed was applied to the determination of sertraline in pharmaceutical formulations. Recoveries were close to 100%, thus proving efficacy of the proposed method for the quantification of sertraline in commercial samples.     

Electrochemical Determination of Phenolic Acids at a Zn/Al Layered Double Hydroxide Film Modified Glassy Carbon Electrode

A stable sensor for the determination of gallic acid (GA) and caffeic acid (CA) was fabricated by electrodeposition of Zn‐Al‐NO₃ layered double hydroxide film on a glassy carbon electrode (LDHf/GCE). A sensitive electrochemical method was achieved for the determination of GA and CA in a phosphate buffer solution (pH 3). The differential pulse voltammetry response of the LDHf/GCE to GA has a linear concentration range from 4 µM to 600 µM with a correlation coefficient of 0.9985 and the calculated detection limit of 1.6 µM at a signal‐to‐noise ratio of 3. The differential pulse voltammetry response of the LDHf/GCE to CA has a linear concentration range from 7 µM to 180 µM with a correlation coefficient of 0.9969 and the calculated detection limit of 2.6 µM at a signal‐to‐noise ratio of 3. The constructed sensor was applied to the determination of GA in commercial green tea samples.     

Development of Electrochemical Platform Based on Molecularly Imprinted Poly(methacrylic acid) Grafted on Iniferter-modified Carbon Nanotubes for 17β-Estradiol Determination in Water Samples

This paper describes the development of a new electrochemical sensor for 17β-estradiol (E2) determination based on glassy carbon electrode (GCE) modified with molecularly imprinted polymer grafted onto iniferter-multiwall carbon nanotubes surface (MIP-MWCNT) and dihexadecyl-hydrogen-phosphate (DHP). The electrochemical method was based on closed-circuit preconcentration of E2 in 0.1 mol L⁻¹ phosphate buffer (pH 7.0) during 500 s. Upon preconcentration, E2 was determined by differential pulse voltammetry (DPV) exhibiting a limit of detection of 0.01 μmol L⁻¹. The sensor exhibited higher selectivity toward E2 and it was applied for E2 determination in natural water samples, with accuracy attested by HPLC-DAD.     

Electrochemical study of the antineoplastic agent etoposide at carbon paste electrode and its determination in spiked human serum by differential pulse voltammetry

The electrochemical oxidation of the antineoplastic agent etoposide was studied at carbon paste electrode in Britton-Robinson buffer solutions over the pH range 2.0-10.0 using cyclic, linear sweep and differential pulse voltammetry. Oxidation of the drug was effected in a single reversible, diffusion-controlled step within the pH range 2.0-4.0, a second oxidation process was produced above pH 4.0. Using differential pulse voltammetry (DPV), the drug yielded a well-defined voltammetric response in Britton-Robinson buffer, pH 3.0 at 0.500 V (vs. Ag/AgCl) on carbon paste electrode. This process could be used to determine etoposide concentrations in the range 2.5 x 10(-7) to 2.5 x 10(-5) M with a detection limit of 1.0 x 10(-7) M. The method was successfully applied to the determination of the drug in spiked human serum.     

木犀草素在玻碳电极上的直接电化学行为及其测定

应用循环伏安法研究木犀草素于玻碳电极的电化学行为.在磷酸盐缓冲液中(pH 4.0),-0.2~+0.8V电位区间内,木犀草素于玻碳电极表面发生的电极反应是吸附控制的准可逆2电子转移过程,电子转移系数α=0.66;建立了检测木犀草素含量的差示脉冲伏安法(DPV).在富集电位+0.4 V下,经富集240 s后,测得木犀草素氧化峰电流Ip与其浓度在1.0×10-8~1.0×10-6mol.L-1范围内呈良好的线性关系,最低检出限为5.0×10-9mol.L-1.本法操作简单、快速、灵敏、准确,可为木犀草素药物质量的控制和检测提供一种简便的新方法.     

一种吖啶酮衍生物的合成及与蛋白质相互作用的电化学行为研究

以乙醇钾为脱氢试剂,吖啶酮为原料合成了10-甲基-吖啶酮,将其硝基化后成功合成了一种新型吖啶酮衍生物—10-甲基-3-硝基-吖啶酮(MNA)。采用循环伏安法对MNA及其与蛋白质相互作用的电化学行为进行研究,并建立了差示脉冲伏安法测定蛋白质的新方法。在PBS缓冲溶液(pH7.0)中,MNA与蛋白质相互作用形成超分子复合物,使其氧化还原峰电流降低,降低值同所加入的牛血清白蛋白(BSA)和人血清白蛋白(HSA)分别在0.4~14 mg/L和0.04~0.28 mg/L范围内呈良好的线性关系,并已应用于实际样品的测定。     

Electrochemical behavior of ascorbic acid at a 2,2'-[3,6-Dioxa-1,8-octanediylbis(nitriloethylidyne)]-bis-hydroquinone carbon paste electrode

Electrocatalytic oxidation of ascorbic acid (AA) at a carbon paste electrode, chemically modified 2,2'-[3,6-dioxa-1,8-octanediylbis(nitriloethylidyne)]-bis-hydroquinone, was thoroughly investigated. The results of cyclic voltammetry, double potential-step chronoamperometry, linear sweep voltammetry and differential pulse voltammetry (DPV) studies were used for the prediction of the mechanism of electrochemical oxidation of AA mediated with 2,2'-[3,6-dioxa-1,8-octanediylbis(nitriloethylidyne)]-bis-hydroquinone at the surface of the modified electrode. The diffusion coefficient (D = 2.45 x 10(-5) cm(2) s(-1)) and the kinetic parameters such as the electron transfer coefficient (alpha = 0.34) were also determined. The results of DPV using the 2,2'-[3,6-dioxa-1,8-octanediylbis(nitriloethylidyne)]-bis-hydroquinone-modified electrode were applied in a highly sensitive determination of AA in drug samples. A linear range of 3.0 x 10(-6) - 1.2 x 10(-4) M and the detection limit (3sigma) 3.8 x 10(-7) M were obtained for DPV determination of AA in buffered pH 7.00 solutions (0.1 M phosphate buffer).     

Voltammetric determination of 4-nitrophenol at a sodium montmorillonite-anthraquinone chemically modified glassy carbon electrode

A new method for the determination of 4-nitrophenol(4-NP) by differential pulse voltammetry (DPV) based on adsorptive stripping technique was described. Cyclic voltammetry (CV) and linear scan voltammetry (LSV) were used in a comparative investigation into the electrochemical reduction of 4-NP at a Na-montmorillonite(SWy-2) and anthraquione (AQ) modified glassy carbon electrode. With this chemically modified electrode, 4-NP was first irreversibly reduced from phiNO(2) to phiNHOH at -0.78 V. A couple of well-defined redox peaks at +0.22 V (vs. SCE) were responsible for a two-electron redox peak between phiNHOH and phiNO. Studies on the effect of pH on the peak height and peak potential were carried out over the pH range 2.0-9.0 with the phosphate buffer solution. A pH of 3.4 was chosen as the optimum pH. The other experimental parameters, such as film thickness, accumulation time and potential etc. were optimized. Anodic peak currents were found to be linearly related to concentration of 4-NP over the range 0.3-45 mg l(-1), with a detection limit of 0.02 mg l(-1). The interference of organic and inorganic species on the voltammetric response have been studied. This modified electrode can be used to the determination of 4-NP in water samples.     

Electrochemical Study of Gliclazide and Its Complexation with β‐Cyclodextrin

The electrochemical oxidation of gliclazide has been investigated at glassy carbon electrode in phosphate buffer solutions over the pH range 2.7–11.8 using cyclic and differential pulse voltammetry (DPV). Gliclazide exhibited one anodic peak in the pH range of 2.7–6.3 and a second peak was produced above pH 6.3. The oxidation processes have been shown to be irreversible and diffusion controlled. The formation of an inclusion complex of gliclazide with β‐cyclodextrin (β‐CD) has been investigated by cyclic and differential pulse voltammetry. A phase solubility study with spectrophotometric detection has been also applied. The stability constant of the complex was determined to be 839 and 360 M^?1 using the differential pulse voltammetric method and the phase solubility method, respectively.     

Voltammetric Determination of Oxybutynin Hydrochloride Utilizing Pencil Graphite Electrode Decorated with Gold Nanoparticles

A novel voltammetric method was successfully applied for the determination of an anticholinergic drug, oxybutynin hydrochloride (OXB). The method is concerned with electrooxidation of the drug on the surface of pencil graphite electrode (PGE). In order to enhance the electrode sensitivity and peak current, the electrode was coated with gold nanoparticles (Au-NPs) via electrochemical deposition using cyclic voltammetry from gold salt solution. The surface of Au-NPs modified PGE has been characterized using scanning electron microscopy and X-ray photoelectron spectroscopy. Various experimental variables were studied and optimized to enhance the sensor's response towards OXB. Quantitative determination of the drug was achieved in phosphate buffer pH 7.5 using differential pulse voltammetry by scanning the potential over range of 0.00 to 2.20 V with scan rate of 40 mV s⁻¹. Validation of the method was achieved according to ICH guidelines. The method was found to be linear over concentration range (2.0×10⁻⁷–1.0×10⁻⁶ M). The suggested sensor was efficiently developed for the quantitative determination of OXB in pure form, pharmaceutical dosage form and spiked plasma samples.     

Application of a Tetraamino Cobalt(II) Phthalocyanine Modified Screen Printed Carbon Electrode for the Sensitive Electrochemical Determination of L-Dopa in Pharmaceutical and Biological Samples

A novel synthesized tetraamino cobalt(II) phthalocyanine monomer was used for the fabrication of a sensor by electrochemical polymerization. A disposable electrochemical sensor based on the use of a screen printed carbon electrode covered with an electropolymerized film of tetraamino cobalt(II) phthalocyanine for the determination of L-dopa in pharmaceutical tablets and biological samples was described. Cyclic voltammetry and electrochemical impedance spectroscopy were performed for the characterization of the bare and modified electrode. For the electrochemical detection of L-dopa differential pulse voltammetry was used. The proposed method exhibits a good response towards electrooxidation of L-dopa in the linear concentration range: from 0.1 to 1000.0 μmol L⁻¹ in BRB pH=2.0, with a detection limit of 0.03 μmol L⁻¹ and from 1 to 1000 μmol L⁻¹ in PBS pH=7.4, with a detection limit of 0.33 μmol L⁻¹. Due to the fact that the developed sensor was applied in two different types of real samples, two buffer media were used, BRB pH=2.0 for pharmaceutical and urine samples and PBS pH=7.4 for whole blood samples. The proposed pCoTAPc/SPCE was successfully applied for the determination of L-dopa in pharmaceutical tablets, urine and in whole blood samples with satisfactory results.     

Selective determination of cysteine in the presence of tryptophan by carbon paste electrode modified with quinizarine

A sensitive and selective electrochemical method for the determination of L-cysteine was developed using a modified carbon paste electrode (MCPE) with quinizarine. Cyclic voltammetry was used to investigate the redox properties of this modified electrode at various solution pH values and at various scan rates. The apparent charge transfer rate constant, ks and transfer coefficient for electron transfer between quinizarine and carbon paste electrode (CPE) were calculated as 2.76 s^?1 and 0.6, respectively. This modified carbon paste electrode shows excellent electrocatalytic activity toward the oxidation of L-cysteine in a phosphate buffer solution (pH 7.0). The linear range of 1.0 × 10^?6 to 1.0 × 10^?3 M and a detection limit (3s) of 2.2 × 10^?7 M were observed in pH 7.0 phosphate buffer solutions. In differential pulse voltammetry, the quinizarine modified carbon paste electrode (QMCPE) could separate the oxidation peak potentials of L-cysteine and tryptophan present in the same solution, though at the unmodified CPE the peak potentials were indistinguishable. This work introduces a simple and easy approach to selective detection of L-cysteine in the presence of tryptophan. Also, the modified electrode was employed for the determination of L-cysteine in the real samples such as serum of blood and acetylcysteine tablet.     

乙酰二茂铁修饰碳糊电极测定废水中对氨基苯酚

利用线性扫描溶出伏安法研究了对氨基苯酚(PAP)在乙酰二茂铁修饰碳糊电极电化学行为。结果表明:在磷酸盐缓冲溶液(pH3.2)中,该修饰电极对PAP具有较好的催化活性,其峰电流与PAP浓度在7.0×10-7～3.0×10-5mol/L范围内呈线性关系,检出限为1.0×10-7mol/L(S/N=3)。利用该法测定了模拟水样中PAP的含量。     

Electrochemical behaviour of sertraline at a hanging mercury drop electrode and its determination in pharmaceutical products

The electrochemical behaviour of sertraline at a hanging mercury drop electrode (HMDE) was described. Different voltammetric techniques, such as cyclic, linear sweep, differential pulse and square wave voltammetry, were used. Voltammograms were obtained at different pH values with a Britton-Robinson buffer solution used as supporting electrolyte. The best results were found by square wave voltammetry with electrodeposition at alkaline pH using a borate buffer with a pH = 8.2 for the samples, containing 12% (v/v) methanol. Under optimised conditions, a linear relationship between 2.33 × 10^–7 and 3.15 × 10^–6 M of sertraline with a limit of detection of 1.98 × 10^–7 M was obtained. The electrochemical method developed was applied to the determination of sertraline in pharmaceutical formulations. Recoveries were close to 100%, thus proving efficacy of the proposed method for the quantification of sertraline in commercial samples. Received: 26 September 2000 / Revised: 1 December 2000 / Accepted: 5 December 2000     

Fast detection of catechin in tea beverage using a poly-aspartic acid film based sensor

A fast and convenient analytical method is presented for the determination of catechin. The electrochemical response of catechin in pH 6.8 phosphate buffer solution is significantly enhanced by immobilization of a film of poly-aspartic acid on the surface of the glassy carbon electrode. The enhancement mechanism and effect factors such as pH value, accumulation time and scan rate, were explored. Under optimum conditions, the differential pulse voltammetry peak current of catechin is proportional to the concentration in the range from 2.5?×?10^?7 to 3.0?×?10^?5 molL^?1, with the detection limit of 7.2?×?10^?8 molL^?1. This method was also applied to the determination of catechin in tea beverage samples, and the recoveries were from 97.1% to 102.7%.     

Electrochemical and Spectroscopic Studies on the Interaction of Gatifloxacin,Moxifloxacin and Sparfloxacin with DNA and Their Analytical Applications

The electrochemical oxidation of the three fluoroquinolone drugs FQs: gatifloxacin GTF, moxifloxacin MXF and sparfloxacin SPF, at the bare and DNA‐modified glassy carbon electrodes has been studied by voltammetric techniques. The three FQs showed one irreversible oxidation peak at potential range 0.85–0.91 V vs. Ag‐AgCl, in phosphate buffer of pH 7.0. Differential pulse voltammetry (DPV) and UV‐absorption spectroscopic techniques were employed to probe the interaction between the FQs and calf thymus double stranded deoxyribonucleic acid (ds CT‐DNA). From electrochemical data, the binding constant between DNA and the gatifloxacin, moxifloxacin and sparfloxacin are calculated to be 3228, 2596 and 2857 M^?1 respectively. Based on electrochemical and spectroscopic results, the mode of binding of fluoroquinolone to DNA through combined effect of intercalation and electrostatic interaction was concluded. A detection scheme based on a preconcentration and differential pulse voltammetric (DPV) determination at dsDNA modified glassy carbon electrode (DNA/GCE) was proposed for the trace determination of the studied analytes. The developed method was successfully applied to the determination of the FQs in pharmaceutical formulations.     

山奈素与蛋白质相互作用的电化学行为研究

应用循环伏安法研究山奈素在活化玻碳电极上的电化学行为及其与人血清白蛋白(HSA)的相互作用,建立差示脉冲伏安法测定HSA的新方法.在pH4.5的磷酸盐缓冲液(PBS)中,山奈素可与HSA形成超分子复合物,导致前者在0.468V处的氧化电流峰下降,其下降值与HSA浓度在0.05～0.25mg/L范围呈线性关系,检出限为0.008mg/L,可应用于血清样品测定.     

Differential Pulse Anodic Stripping Voltammetric Determination of Lead (II) Using Poly Xylenol Orange Modified Electrode

In this work a method for sensitive anodic stripping voltammetric determination of Pb(II) ions using a poly xylenol orange film modified electrode (PXOFME) has been proposed. Poly xylenol orange film (PXOF) was formed on a paraffin impegrenated graphite electrode (PIGE) using electro polymerization method by scanning the potential between −0.5 V to 1.3 V, at a scan rate of 50 mV/s for 30 segments in 0.1 M phosphate buffer solution (PBS) of pH 7. The PXOFME was characterized by scanning electron microscopy (SEM), ATR‐IR spectroscopy, cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS). The modified electrode has been used to develop a sensitive method for the determination of Pb(II) ions by anodic stripping voltmmetry (ASV). The PXOFME was used to preconcentrate Pb(II) ions through complexation, the complexed metal ions were reduced electrochemically and then stripped anodically from the surface of the electrode. A linear range of 5 μg/L to 413 μg/L with a limit of detection (S/N=3) of 1.6 μg/L was observed for the determination of Pb(II) ions. The method was applied to lead determination in sea water and tap water samples and the results were found to be satisfactory.     

Electrochemical Determination and in silico Studies of Fludarabine on NH2 Functionalized Multiwalled Carbon Nanotube Modified Glassy Carbon Electrode

A sensitive voltammetric technique has been developed for the determination of Fludarabine using amine‐functionalized multi walled carbon nanotubes modified glassy carbon electrode (NH₂‐MWCNTs/GCE). Molecular dynamics simulations, an in silico technique, were employed to examine the properties including chemical differences of Fludarabine‐ functionalized MWCNT complexes. The redox behavior of Fludarabine was examined by cyclic, differential pulse and square wave voltammetry in a wide pH range. Cyclic voltammetric investigations emphasized that Fludarabine is irreversibly oxidized at the NH₂‐MWCNTs/GCE. The electrochemical behavior of Fludarabine was also studied by cyclic voltammetry to evaluate both the kinetic (k_s and E_a) and thermodynamic (ΔH, ΔG and ΔS) parameters on NH₂‐MWCNTs/GCE at several temperatures. The mixed diffusion‐adsorption controlled electrochemical oxidation of Fludarabine revealed by studies at different scan rates. The experimental parameters, such as pulse amplitude, frequency, deposition potential optimized for square‐wave voltammetry. Under optimum conditions in phosphate buffer (pH 2.0), a linear calibration curve was obtained in the range of 2×10^?7 M–4×10^?6 M solution using adsorptive stripping square wave voltammetry. The limit of detection and limit of quantification were calculated 2.9×10^?8 M and 9.68×10^?8 M, respectively. The developed method was applied to the simple and rapid determination of Fludarabine from pharmaceutical formulations.