Effect of surface morphology on membrane fouling by humic acid with the use of cellulose acetate butyrate hollow fiber membranes

A serious problem faced during the application of membrane filtration in water treatment is membrane fouling by natural organic matter (NOM). The hydrophilicity, zeta potential and morphology of membrane surface mainly influence membrane fouling. The aim of the present study is to reveal the correlation between membrane surface morphology and membrane fouling by use of humic acid solution and to investigate the efficiency of backwashing by water, which is applied to restore membrane flux. Cellulose acetate butyrate (CAB) hollow fiber membranes were used in the present study. To obtain the membranes with various surface structures, membranes were prepared via both thermally induced phase separation (TIPS) and nonsolvent-induced phase separation (NIPS) by changing the preparation conditions such as polymer concentration, air gap distance and coagulation bath composition. Since the membrane material is the same, the effects of hydrophilicity and zeta potential on membrane fouling can be ignored. More significant flux decline was observed in the membrane with lower humic acid rejection. For the membranes with similar water permeability, the lower the porosity at the outer surface, the more serious the membrane fouling. Furthermore, the effect of the membrane morphology on backwashing performance was discussed.     

Transparent polymer blends composed of cellulose acetate propionate and poly(epichlorohydrin)

Structure and properties for binary blends composed of biomass-based cellulose acetate propionate (CAP) and poly(epichlorohydrin) (PECH) have been studied. It is found from the dynamic mechanical measurements that mutual dissolution takes place to some degree with remaining CAP-rich and PECH-rich regions in the blends. As a result of the interdiffusion, leading to fine morphology, the blends exhibit high level of optical transparency although the individual pure components have different refractive index. Furthermore, the mechanical toughness of CAP, which is one of the most serious problems for CAP, is considerably improved by blending PECH. This will have a great impact on industries because the blend technique widens the application of CAP.     

Miscibility of cellulose acetate with vinyl polymers

Binary blend films of cellulose acetate (CA) with flexible syntheticpolymers including poly(vinyl acetate) (PVAc), poly(N-vinyl pyrrolidone) (PVP),and poly(N-vinyl pyrrolidone-co-vinyl acetate) [P(VP-co-VAc)] were preparedfrommixed polymer solutions by solvent evaporation. Thermal analysis by DSC showedthat CA of any degree of substitution (DS) was not miscible with PVAc, but CAwith DS less than 2.8 was miscible with PVP to form homogeneous blends. Thestate of mixing in CA/P(VP-co-VAc) blends was affected not only by the DS of CAbut also by the VP/VAc copolymer composition. As far as CAs of DS<2.8 andP(VP-co-VAc)s with VP contents more than ca. 25 mol% were used,theCA/copolymer blends mostly showed a miscible behaviour irrespective of themixing ratio. FT-IR measurements for the miscible blends of CA/PVP andCA/P(VP-co-VAc) revealed the presence of hydrogen-bonding interactions betweenresidual hydroxyls of CA and carbonyls of N-vinyl pyrrolidone units, which maybe assumed to largely contribute to the good miscibility.     

Investigation of melamine and DOPO-derived flame retardants for the bioplastic cellulose acetate

In order to identify suitable flame retardant additives for the eco-friendly polymer cellulose acetate (CA), high-melting derivatives of the known flame retardant 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) were combined with the thermoplastic CA and the combustion properties were tested. CA mixtures with bis-phosphonamidates (EDA-DOPO and PIP-DOPO) showed distinct flame retardation effects and a reduction of peak heat release rates (PHRR) by up to 18%. CA mixtures with MDOP, a melamine salt of DOPA (an oxidation product of DOPO), also showed considerable effects and a reduction of PHRR by up to 27%. While producing more smoke than pure CA and CA plus melamine, owing to its aromatic component, MDOP was superior to the CA mixtures with DOPO, EDA-DOPO and PIP-DOPO in this regard. The mixture of CA with melamine gave rise to a distinctly reduced formation of toxic CO and smoke when compared with pure CA. Thus, these additives can be considered for future applications of CA-based polymers with enhanced flame protection.     

Homogeneous modification of carbon nanotubes with cellulose acetate

An efficient strategy that comprised shorten,chain extension,active groups introducing and homogeneous reaction tactics,was adopted to modify multiwalled carbon nanotubes(MWNTs) with cellulose acetate(CA).Specially,by utilizing 2,4,6-trichloro- 1,3,5-triazine,a reactive intermediate of the MWNTs(MWNT-triazine) was obtained.Suitable solubility of the MWNT-triazine helps make the homogeneous modification become reality.Detailed characterizations further verified that reaction between chloride atoms in the ...     

Electrospun cellulose acetate fibers: effect of solvent system on morphology and fiber diameter

This paper reports an investigation of the effects of solvent system, solution concentration, and applied electrostatic field strength (EFS) on the morphological appearance and/or size of as-spun cellulose acetate (CA) products. The single-solvent systems were acetone, chloroform, N,N -dimethylformamide (DMF), dichloromethane (DCM), methanol (MeOH), formic acid, and pyridine. The mixed-solvent systems were acetone–DMAc, chloroform–MeOH, and DCM–MeOH. Chloroform, DMF, DCM, MeOH, formic acid, and pyridine were able to dissolve CA, forming clear solutions (at 5% w/v), but electrospinning of these solutions produced mainly discrete beads. In contrast, electrospinning of the solution of CA in acetone produced short and beaded fibers. At the same solution concentration of 5% (w/v) electrospinning of the CA solutions was improved by addition of MeOH to either chloroform or DCM. For all the solvent systems investigated smooth fibers were obtained from 16% (w/v) CA solutions in 1:1, 2:1, and 3:1 (v/v) acetone–DMAc, 14–20% (w/v) CA solutions in 2:1 (v/v) acetone–DMAc, and 8–12% (w/v) CA solutions in 4:1 (v/v) DCM–MeOH. For the as-spun fibers from CA solutions in acetone–DMAc the average diameter ranged between 0.14 and 0.37 μm whereas for the fibers from solutions in DCM–MeOH it ranged between 0.48 and 1.58 μm. After submersion in distilled water for 24 h the as-spun CA fibers swelled appreciably (i.e. from 620 to 1110%) but the physical integrity of the fibrous structure remained intact.     

In vitro evaluation of cellulose acetate hemodialyzer immobilized with heparin

In this study, heparin was immobilized onto cellulose acetate hollow fibers to improve the anticoagulation performance during hemodialysis. In vitro evaluation was carried out using mini‐hemodialyzer circulating with fresh porcine whole blood to simulate kidney therapy. The dialysis performance and hemocompatibility were estimated. The results showed that heparinized hemodialyzer could be used through out the whole dialysis time (4 hr) without injecting additional heparin to prevent coagulation in the dialysis system. In addition, the hemocompatibility was evaluated by measuring activated partial thromboplastin time (APTT), prothrombin time (PT), and fibrinogen time (FT). The complete blood count (CBC) including red blood cell (RBC), hemoglobin (Hgb), hematocrit (Hct), white blood cell (WBC), and platelet were determined. The results showed that heparinization could keep the CBC stable during dialysis, whereas unmodified cellulose acetate hemodialyzer would cause a decrease in RBC unless heparin was injected during dialysis. Heparinized hemodialyzer showed longer APTT, PT, and FT than unmodified hemodialyzer. Heparinized hemodialyzer also showed slightly higher clearance than unmodified hemodialyzer. These results indicated that the dialysis performance and hemocompatibility of cellulose acetate hemodialyzer could be improved by the immobilization of heparin. Copyright © 2006 John Wiley & Sons, Ltd.     

Enhancement of cellulose acetate degradation under accelerated weathering by plasticization with eco-friendly plasticizers

Cellulose acetate (CA) with a degree of substitution (DS) of 2.5 has been plasticized using eco-friendly plasticizers such as triacetin, tripropionin, triethyl citrate, tributyl citrate, tributyl 2-acetyl citrate and poly(ethylene glycol) of low molecular weight. Thermo-mechanical properties and hydrophilicity of the modified CA have been measured and correlated with the content and nature of the plasticizer used and compared with unplasticized CA. The increase in toughening and the change in the hydrophilicity by the plasticization were evaluated in terms of aging and weathering stability under accelerated conditions. Samples were exposed to UV-degradation with water spray periods. The treated samples were removed periodically and characterized by several analytical techniques. The results are discussed with particular emphasis toward the effects of plasticization on enhancement of the degradation rate of CA. The plasticization of CA triggered an increase of the weight loss between 50 and 90%, where low molecular weight plasticizers were shown to be more effective. A right balance between hydrophilicity and plasticization efficiency (reduction of T_g) is needed to increase the degradation rate of CA.     

Novel nanocomposite membranes from cellulose acetate and clay‐silica nanowires

In this study, a new class of heterogeneous membranes based on cellulose acetate (CA) polymer and a complex filler clay‐silica nanowires (SiO₂NWs) was investigated for potential biomedical applications. SiO₂NWs were synthesized using natural clay through a facile sol–gel method and were dispersed in the polymer solution by sonication in the 1.25, 2.5, and 5% weight ratio to the CA acetate polymer. Membranes were subsequently prepared via phase inversion by precipitation of the CA polymer in water. The pristine CA membrane and SiO₂NWs based nanocomposites membranes were characterized using different characterization techniques. The presence of the SiO₂NWs in the CA membrane was found to significantly enhance the protein retention, water wettability and thermal as well as mechanical properties in comparison to the pristine CA membrane. Water flows studies at different temperatures and the retention of bovine serum albumin have been studied and the nanocomposite membranes were found to exhibit superior performances compared with the pristine CA membranes. SiO₂NWs‐CA membranes showed a much higher stability to the water temperature change during separation than CA membranes. Morphological changes clearly revealed that the composite membrane were much more compact than the pristine CA membranes. The rabbit dermal fibroblasts cell viability in cultures after 72 hr of incubation was found to be greater than 80%. These newly synthesized composite membranes exhibit a high potential to be used for various medical applications because of their non‐cytotoxic characteristics. Copyright © 2016 John Wiley & Sons, Ltd.     

Molecular structure and properties of cellulose acetate chemically modified with caprolactone

Cellulose acetate (CA) with a degree of substitution of 1.7 was modified with caprolactone (CL) under various reaction conditions in an internal mixer. Processing temperature changed from 120 to 220 °C, while reaction time varied between 5 and 45 min. The composition and structure of the polymer was analyzed by various methods including FTIR, MALDI-TOF and NMR spectroscopy and its mechanical characteristics were determined by dynamic mechanical analysis and tensile testing. The results indicate that homopolymerization occurs under relatively mild conditions, while grafting requires higher temperatures and longer times. Grafted polycaprolactone (gPCL) chains are attached mainly to positions 2 and 6 of the glucose ring and their length increases with increasing reaction time and temperature, but the chains are always much shorter than those obtained in solution polymerization. Changes in the degree of substitution during grafting are small indicating that homopolymerization proceeds easier than grafting. Grafting seems to be easier in cellulose acetate with a larger degree of substitution in spite of the smaller number of active -OH groups present. Internal plasticization is more efficient than the external plasticizing effect of monomeric caprolactone. Plasticization results in a decrease of stiffness and strength, but deformability increases only slightly.     

Synthesis, characterization and thermal studies on cellulose acetate membranes with additive

Cellulose acetate (CA) membranes are used in ultrafiltration applications, although they show low chemical, mechanical and thermal resistance. In order to prepare membranes with improved properties, modification of cellulose acetate with polyethelene glycol (PEG 600) has been attempted. In this study, CA has been mixed with PEG 600 as an additive in a polar solvent. The effects of CA composition and additive concentration given by a mixture design of experiments on membrane compaction, pure water flux, water content and membrane hydraulic resistance have been studied and discussed. The efficiency of protein separation by the developed CA membranes have been quantified using model proteins such as pepsin, egg albumin (EA) and bovine serum albumin (BSA). The thermal stability of the developed membranes prepared with PEG 600 additive has also been investigated using thermogravimetric analysis and differential scanning calorimetry.     

Factors affecting adsorption of organic solutes on cellulose acetate in an aqueous solution system

Summary The adsorption properties of esters, aldehydes, ethers and amides on cellulose acetate, which is commonly used as a reverse osmosis membrane material, in an aqueous solution system were measured by high-performance liquid chromatography. The adsorption property was characterized with the specific retention volume. For a noncyclic homologous series the logarithm of the specific retention volume was linearly correlated with the logarithm of the partition coefficient between 1-octanol and water. The fact that the slopes of these regression lines are almost identical confirms that the dominant effect on adsorption is the hydrophobic interaction between cellulose acetate and the solute molecule. The intercept represents the effect of the polar groups on adsorption. The effect of the polar group decreases as follows: C(O)O, CO, HCON > CH₃CON > OH, O.     

Polymeric membranes based on cellulose acetate loaded with candle soot nanoparticles for water desalination

This study is concerned with modifying cellulose acetate (CA)/polyethylene glycol (PEG) membranes prepared via phase inversion technique in the presence of carbon nanoparticles; candle soot (CS) resulting from combusted candle. CS nanoparticles were analyzed via Fourier transform infrared spectroscopy and transmission electron microscopy. The developed membranes were characterized for their surface morphology, mechanical properties as well as thermal stability. CS nanoparticles contributed in improving the salt rejection % with a slight reduction in the water flux behavior. Employing the annealed cellulose acetate/polyethylene glycol membranes loaded with candle soot nanoparticles provides an adequate approach towards water desalination implementations.     

Integrated photografted molecularly imprinted polymers with a cellulose acetate membrane for the extraction of melamine from dry milk before HPLC analysis

In this study, a new separation technique based on membrane extraction is described for the determination of melamine in dry milk. The water‐compatible cellulose acetate membrane, which is photografted by melamine imprinted nanospheres, was prepared by placing the membrane into the polymerization solution containing methacrylic acid as a functional monomer, ethylene glycol dimethacrylate as cross‐linker, acetonitrile as porogen, and melamine as the template molecule. The characterization of the polymeric membrane was performed by Fourier transmission infrared spectroscopy and scanning electron microscopy. This integrated composite membrane was used as a solid‐phase extraction medium for the extraction of melamine from dry milk samples. Various parameters affecting the extraction efficiency of the membrane were evaluated. The results showed higher binding capacity for melamine imprinted membranes in comparison with the nonimprinted membranes. High‐performance liquid chromatography analysis showed that the extraction of melamine from dry milk by the photografted cellulose acetate membrane had a linear calibration curve in the range of 0.02–11.80 μg/mL with an excellent precision of 2.73%. The limit of detection and quantification of melamine was 0.007 and 0.020 μg/mL, respectively. The recoveries of melamine were in the range of 88.7–94.8%.     

On-line extraction and determination of uranium in aqueous samples using multi-walled carbon nanotubes-coated cellulose acetate membrane

In this work, multi-walled carbon nanotubes (MWCNTs)-coated cellulose acetate membrane was used for on-line extraction and pre-concentration of uranium from aqueous samples prior to inductively coupled plasma optical emission spectrometry (ICP-OES) determination. Sample solutions containing the U(VI)-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP) complex were passed through the membrane. The adsorbed analyte was subsequently eluted from the membrane with acid, which was directly introduced into the ICP-OES nebuliser. The main variables affecting the pre-concentration and determination steps of uranium were studied and optimised. Under the optimised conditions, the enrichment factor of 150 and the detection limit of 0.16 μg L^–1 were obtained. This method was successfully used for determination of uranium in environmental water samples.     

A facile synthesis of cellulose acetate reinforced graphene oxide nanosheets as proton exchange membranes for fuel cell applications

In this work, for the first time, a simple casting process is used to create an efficient and highly stable cellulose acetate (CA) based membrane with dispersive graphene oxide nanosheets (GO). The successful preparation of GO and its integration into the polymer matrix was verified by structural and morphological characterization using FTIR, TEM, SEM, and XRD. Furthermore, the impact of GO nanosheets and their content on the composite membranes' physicochemical properties is investigated. The water uptake increased up to 24% as the concentration of GO increased, while the ion exchange capacity increased threefold compared to the blank CA membrane. Additionally, increasing GO loading also enhanced the proton conductivity and the tensile strength of the developed membranes. The homogeneous CA/GO nanocomposite membranes with GO filler amounts ranging from 0.3 to 0.8 wt% were found to have excellent proton conductivity varying from 9.2 to 15.5 mS/cm compared to 6.94 mS/cm for Nafion 212. Further, as systematically studied and compared in membrane performance, the overall power density of the membrane electrode assembly (MEA) with GO content was increased up to 519 mW/cm² compared to 401 mW/cm² for Nafion 212 with significantly lower cost. The encouraging outcomes of this study pave the way for a simple, environmentally friendly, and cost-effective approach for developing nanocomposite membranes for application in PEMFCs.     

A simple method for functionalization of cellulose membrane for covalent immobilization of biomolecules

Activated cellulose membrane was prepared by a simple photochemical reaction at 365 nm in 12 min using a photolinker, 1-fluoro-2-nitro-4-azidobenzene. XPS analysis of the activated cellulose membrane confirmed the presence of nitrogen and fluorine in the ratio of 2:1. Immobilization of a protein molecule onto the activated membrane occurred in 2 h at 37 °C. In contrast, no appreciable immobilization occurred onto the untreated surface. Disappearance of the fluorine peak in the XPS spectra of membrane having immobilized HRP confirmed covalent binding of the protein onto the activated membrane. Invertase was also immobilised onto the activated membrane and used in a flow through reactor system for conversion of sucrose to glucose and fructose. Immobilized invertase was found to be stable for at least 72 h of continuous run. The kinetic parameters of the enzyme reaction, Michaelis constant (K_m) and V_max value of immobilized invertase was studied. The activated membrane when used in an ELISA procedure to detect immunoglobulins in human sera, showed around 2.6-fold higher sensitivity than the untreated membrane. The activated cellulose membrane has the potential for versatile applications such as in diagnostics, in flow reactor system for an enzyme-catalysed reaction and in membrane based affinity chromatography.     

Evaluation of the permeability of modified cellulose acetate propionate membranes for use in biosensors based on hydrogen peroxide detection

Phase inversion cellulose acetate propionate membranes showed lowpermeability to hydrogen peroxide aqueous solutions. Their permeability wasincreased by alkaline hydrolysis of the ester linking units. However, thepermeability remained lower than that of an unsubstituted cellulose membrane.The inclusion of hydroxypropyl cellulose in the membrane formulation, followedby an alkaline hydrolysis step, increased permeability to hydrogen peroxideaqueous solutions to 29% of that of an unsubstituted cellulose membrane.     

Permeation of water as a tool for characterizing the effect of solvent, film thickness and water solubility in cellulose acetate membranes

Cellulose acetate membranes have been used in many applications; of particular interest are reverse osmosis systems, and as a neutral matrix for incorporation of different polymers (e.g., conducting polymers), inorganic ions (e.g., lanthanides) and organic (e.g., pharmaceutical) compounds. The properties of the new polymers derived from cellulose acetate or blends depend on those of cellulose acetate. This work presents an attempt to find links between thermodynamic and kinetic properties of cellulose acetate membranes in equilibrium with water. Water diffusion coefficients in cellulose acetate membranes are reported, measured with a simple water permeation technique. The comparison of these values with the percentage of water uptake and polymer thickness leads to interesting conclusions related with different polymer properties.