Stability analysis and transition prediction of hypersonic boundary layer over a blunt cone with small nose bluntness at zero angle of attack

Stability and transition prediction of hypersonic boundary layer on a blunt cone with small nose bluntness at zero angle of attack was investigated. The nose radius of the cone is 0.5 mm; the cone half-angle is 5°, and the Mach number of the oncoming flow is 6. The base flow of the blunt cone was obtained by direct numerical simulation. The linear stability theory was applied for the analysis of the first mode and the second mode unstable waves under both isothermal and adiabatic wall condition, and eN method was used for the prediction of transition location. The N factor was tentatively taken as 10, as no experimentally confirmed value was available. It is found that the wall temperature condition has a great effect on the transition location. For adiabatic wall, transition would take place more rearward than those for isothermal wall. And despite that for high Mach number flows, the maximum amplification rate of the second mode wave is far bigger than the maximum amplification rate of the first mode wave, the transition location of the boundary layer with adiabatic wall is controlled by the growth of first mode unstable waves. The methods employed in this paper are expected to be also applicable to the transition prediction for the three dimensional boundary layers on cones with angle of attack.     

Effect of disturbances at inlet on hypersonic boundary layer transition on a blunt cone at small angle of attack

To investigate the effect of different disturbances in the upstream, we present numerical simulation of transition for a hypersonic boundary layer on a 5-degree half-angle blunt cone in a freestream with Mach number 6 at 1-degree angle of attack. Evolution of small disturbances is simulated to compare with the linear stability theory （LST）, indicating that LST can provide a good prediction on the growth rate of the disturbance. The effect of different disturbances on transition is investigated. Transition onset distributions along the azimuthal direction are obtained with two groups of disturbances of different frequencies. It shows that transition onset is relevant to frequencies and amplitudes of the disturbances at the inlet, and is decided by the amplitudes of most unstable waves at the inlet. According to the characteristics of environmental disturbances in most wind tunnels, we explain why transition occurs leeside-forward and windside-aft over a circular cone at an angle of attack. Moreover, the indentation phenomenon in the transition curve on the leeward is also revealed.     

Prediction of hypersonic boundary layer transition on sharp wedge flow considering variable specific heat

When the air temperature reaches 600 K or higher, vibration is excited. The specific heat is not a constant but a function of temperature. Under this condition, the transition position of hypersonic sharp wedge boundary layer is predicted by using the improved eN method considering variable specific heat. The transition positions with different Mach numbers of oncoming flow, half wedge angles, and wall conditions are computed condition, the nearer to the Mach number The results show that for the same oncoming flow condition and wall transition positions of hypersonic sharp wedge boundary layer move much leading edge than those of the flat plate. The greater the oncoming flow the closer the transition position to the leading edge.     

Second mode unstable disturbance measurement of hypersonic boundary layer on cone by wavelet transform

Experimental investigation of hypersonic boundary layer instability on a cone is performed at Mach number 6 in a hypersonic wind tunnel.Time series signals of instantaneous fluctuating surface-thermal-flux are measured by Pt-thin-film thermocouple temperature sensors mounted at 28 stations on the cone surface in the streamwise direction to investigate the development of the unstable disturbance.Wavelet transform is employed as a mathematical tool to obtain the multi-scale characteristics of fluctuating surfacethermal-flux both in the temporal and spectrum space.The conditional sampling algorithm using wavelet coefficient as an index is put forward to extract the unstable disturbanceThe generic waveform for the second mode unstable disturbance is obtained by a phase-averaging technique.The development of the unstable disturbance in the streamwise direction is assessed both in the temporal and spectrum space.Our study shows that the local unstable disturbance detection method based on wavelet transformation offers an alternative powerful tool in studying the hypersonic unstable mode of laminar-turbulent transition.It is demonstrated that,at hypersonic speeds,the dominant flow instability is the second mode,which governs the course of laminar-turbulent transition of sharp cone boundary layer.     

NUMERICAL INVESTIGATION OF EVOLUTION OF DISTURBANCES IN SUPERSONIC SHARP CONE BOUNDARY LAYERS

The spatial evolution of 2-D disturbances in supersonic sharp cone boundary layers was investigated by direct numerical simulation (DNS) in high order compact difference scheme. The results suggested that, although the normal velocity in the sharp cone boundary layer was not small, the evolution of amplitude and phase for small amplitude disturbances would be well in accordance with the results obtained by the linear stability theory (LST) which supposes the flow was parallel. The evolution of some finite amplitude disturbances was also investigated, and the characteristic of the evolution was shown. Shocklets were also found when the amplitude of disturbances increased over some value.     

Response of a hypersonic blunt cone boundary layer to slow acoustic waves with assessment of various routes of receptivity

The hypersonic boundary-layer receptivity to slow acoustic waves is investigated for the Mach 6 flow over a 5-degree half-angle blunt cone with the nose radius of 5.08 mm. The plane acoustic wave interacts with the bow shock, and generates all types of disturbances behind the shock, which may take various routes to generate the boundary-layer unstable mode. In this paper, two routes of receptivity are investigated in detail. One is through the disturbance in the entropy layer. The other is through the slow acoustic wave transmitted downstream the bow shock, which can excite the boundary-layer mode due to the synchronization mechanism. The results show that, for a low frequency slow acoustic wave, the latter route plays a leading role. The entropy-layer instability wave is able to excite the first mode near the neutral point, but its receptivity efficiency is much lower.     

Experimental study of compressible boundary layer on a cone at angles of attack

Experimental study was conducted for boundarylayers on a sharp 5° half-angle cone of 400mm length at angles of attack. The model was tested in the T-326 hypersonic wind tunnel （ITAM） at freestream Mach number M = 5.95. Mean and fluctuation wall characteristics of the boundary layer are measured at 0°, 2°, 3° and 4° angles of attack for different stagnation pressures. Pulsation measurements are carried out by means of ALTP sensor. Pressure and temperature distributions along the model are obtained, and transition beginning and end locations have been found. Boundary layer stabilization with the increase of angle of attack and the decrease of stagnation pressure is observed. High frequency pulsations inherent to hypersonic boundary layer （second mode） have been detected.     

Supersonic flow past a sharp cone oscillating about a zero angle of attack

Supersonic perfect gas or equilibrium dissociated air flow past a sharp circular cone oscillating about a zero angle of attack is considered at small Strouhal numbers. The distribution of the gasdynamic parameters in the flow is found within the framework of the linear theory of finite-thickness bodies. The domain of the determining parameters for which the effect of equilibrium dissociation is substantial is found. The pitch moment coefficient related to the angular velocity of vibration is determined. Analytic expressions are derived for the gasdynamic characteristics at hypersonic flow velocities. Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 6, pp. 124–136, November–December, 1998.     

Direct numerical simulation of disturbances generated by periodic suction-blowing in a hypersonic boundary layer

A numerical algorithm and code are developed and applied to direct numerical simulation (DNS) of unsteady two-dimensional flow fields relevant to stability of the hypersonic boundary layer. An implicit second-order finite-volume technique is used for solving the compressible Navier–Stokes equations. Numerical simulation of disturbances generated by a periodic suction-blowing on a flat plate is performed at free-stream Mach number 6. For small forcing amplitudes, the second-mode growth rates predicted by DNS agree well with the growth rates resulted from the linear stability theory (LST) including nonparallel effects. This shows that numerical method allows for simulation of unstable processes despite its dissipative features. Calculations at large forcing amplitudes illustrate nonlinear dynamics of the disturbance flow field. DNS predicts a nonlinear saturation of fundamental harmonic and rapid growth of higher harmonics. These results are consistent with the experimental data of Stetson and Kimmel obtained on a sharp cone at the free-stream Mach number 8.     

Traveling disturbance appearing in boundary layer transition in a Yawed cylinder

Boundary layers that develop over a body in fluid flow are in most cases three-dimensional owing to the spin, yaw, or surface curvature of the body. Therefore, the study of three-dimensional (3D) boundary-layer transition is essential to work in practical aerodynamics. The present investigation is concerned with the problem of 3D boundary layers over a yawed body. A yawed cylinder model that represents the leading edge portion of a swept wing and the mechanism of crossflow instability are investigated in detail using hot-wire velocimetry and a flow visualization technique. As a result, traveling disturbances having frequencies f₁ and f₂, which differ by about one order of magnitude, are detected in the transition region. The phase velocities and directions of travel of those disturbances are measured. Results for the low-frequency disturbance f₁ show qualitative coincidence with results numerically predicted for a crossflow unsteady disturbance. Nameley, F₁ travels nearly spanwise to the yawed cylinder and very close to the cylinder wall. The results for the high-frequency disturbance f₂ good agreement with the existing experimental results. The ₂ disturbance is found to be the high-frequency inflectional secondary instability that appears in 3D boundary layer transition in general. A two-stage transition process, where stationary crossflow vortices appear as the primary instability and a traveling inflectional disturbance is generated as a secondary instability, was observed. Secondary instability seems to play a major role in turbulent transition.     

Numerical modeling of laminar-turbulent transition in a boundary layer at a high freestream turbulence level

Disturbances generated by external turbulence in the boundary layer on a flat plate set suddenly in motion are determined by numerically solving the Navier-Stokes equations. The results of direct numerical simulation of isotropic homogenous turbulence are taken as initial conditions. The solution obtained models laminar-turbulent transition in the flat-plate boundary layer at a high freestream turbulence level, time measured from the onset of the motion serving as the longitudinal coordinate. The solution makes it possible to estimate the effect of different factors, such as flow unsteadiness and nonlinearity and the characteristics of the freestream velocity fluctuation spectrum, on laminar-turbulent transition in the boundary layer.     

Development of slow disturbances in a hypersonic boundary layer

The mechanisms of development of slow time-dependent disturbances in the wall region of a hypersonic boundary layer are established and a diagram of the disturbed flow patterns is plotted; the corresponding nonlinear boundary value problem is formulated for each of these regimes. It is shown that the main factors that form the disturbed flow are the gas enthalpy near the body surface, the local viscous-inviscid interaction level, and the type, either subsonic or supersonic, of the boundary layer as a whole. Numerical and analytical solutions are obtained in the linear approximation. It is established that enhancement of the local viscous-inviscid interaction or an increased role for the main supersonic region of the boundary layer makes the disturbed flow by and large “supersonic”: the upstream propagation of the disturbances becomes weaker, while their downstream growth is amplified. Contrariwise, local viscous-inviscid interaction attenuation or an increased role for the main subsonic region of the boundary layer has the opposite effect. Surface cooling favors an increased effect of the main region of the boundary layer while heating favors an increased wall region effect. It is also found that in the regimes considered disturbances travel from the turbulent flow region downstream of the disturbed region under consideration counter to the oncoming flow, which may be of considerable significance in constructing the nonlinear stability theory.     

Investigating flow topologies in boundary layer transition using direct numerical simulation

A numerical method developed for simulating three-dimensional incompressible boundary layer flow is presented. K-type transition up to the two-spike stage is simulated, and flow topologies at various stages of transition are determined. Comparison with flow topologies from other simulations of turbulent and transitioning flows is made. Financial support provided by Air Operations Division, Aeronautical and Maritime Research Laboratory, Defence Science and Technology Organisation, Australia.     

The effects of variable specific heat on the stability of hypersonic boundary layer on a flat plate

The gas temperature within hypersonic boundary layer flow is so high that the specific heat of gas is no longer a constant but relates to temperature. How variable specific heat influences on boundary layer flow stability is worth researching. The effect of the variable specific heat on the stability of hypersonic boundary layer flows is studied and compared with the case of constant specific heat based on the linear stability theory. It is found that the variable specific heat indeed has some effects on the neutral curves of both the first-mode and the second-mode waves and on the maximum rate of growth also. Therefore, the relationship between specific heat and temperature should be considered in the study of the stability of the boundary layer.     

Laminar-turbulent transition in the boundary layer on cones in a hypersonic flow at high Reynolds numbers per meter

The laminar-turbulent transition is experimentally studied in boundary-layer flows on cones with a rectangular axisymmetric step in the base part of the cone and without the step. The experiments are performed in an A-1 two-step piston-driven gas-dynamic facility with adiabatic compression of the working gas with Mach numbers at the nozzle exit M _∞ = 12–14 and pressures in the settling chamber P₀ = 60–600 MPa. These values of parameters allow obtaining Reynolds numbers per meter near the cone surface equal to Re _1e = (53–200) · 10⁶ m ⁻¹. The transition occurs at Reynolds numbers Re _tr = (2.3–5.7) · 10⁶. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 48, No. 3, pp. 76–83, May–June, 2007.     

Evolution of disturbances in a laminarized supersonic boundary layer on a swept wing

Experimental data on stability of a three-dimensional supersonic boundary layer on a swept wing are presented. The experiments are performed on a swept wing model with a lenticular profile with a 40° sweep angle of the leading edge at a zero angle of attack. The supersonic boundary layer on the swept wing was laminarized with the use of distributed roughness. A pioneering study of interaction of traveling and stationary disturbances is performed. Some specific features of this interaction are identified. The main reason for turbulence emergence in a supersonic boundary layer on a swept wing is demonstrated to be secondary crossflow instability. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 49, No. 2, pp. 40–46, March–April, 2008.     

Investigation of a hypersonic crossing shock wave/turbulent boundary layer interaction

A combined theoretical and experimental study is presented for the interaction between crossing shock waves generated by (10°, 10°) sharp fins and a flat plate turbulent boundary layer at Mach 8.3. The theoretical model is the full 3-D mean compressible Reynolds-averaged Navier-Stokes RANS) equations incorporating the algebraic turbulent eddy viscosity model of Baldwin and Lomax. A grid refinement study indicated that adequate resolution of the flowfield has been achieved. Computed results agree well with experiment for surface pressure and surface flow patterns and for pitot pressure and yaw angle profiles in the flowfield. The computations, however, significantly overpredict surface heat transfer. Analysis of the computed flowfield results indicates the formation of complex streamline and wave structures within the interaction region.This article was processed using Springer-Verlag T_EX Shock Waves macro package 1.0 and the AMS fonts, developed by the American Mathematical Society.     

STUDY OF MECHANISM OF BREAKDOWN IN LAMINARTURBULENT TRANSITION OF SUPERSONIC BOUNDARY LAYER ON FLAT PLATE

Spatial mode direct numerical simulation has been applied to study the mechanism of breakdown in laminar-turbulent transition of a supersonic boundary layer on a flat plate with Mach number 4.5. Analysis of the result showed that, during the breakdown process in laminar-turbulent transition, the mechanism causing the mean flow profile to evolve swiftly from laminar to turbulent was that the modification of mean flow profile by the disturbance, when they became larger, leads to remarkable change of its stability characteristics. Though the most unstable T-S wave was of second mode for laminar flow, the first mode waves played the key role in the breakdown process in laminar-turbulent transition.     

Effect of the freestream turbulence scale and the leading edge shape on boundary layer laminar-turbulent transition

The effect of the leading edge shape and the turbulence scale on laminar-turbulent transition in the flat-plate boundary layer due to grid turbulence is investigated. In the experiments, the turbulence scale was changed by a factor of three and the bluntness radius of the edge by a factor of four, all other factors being fixed. It is shown that on the plate with a sharp edge the fluctuation growth rate and the laminar-turbulent transition point depend nonmonotonically on the turbulence scale. On the blunt plate transition occurs considerably earlier than on the sharp plate.     

Study of laminar boundary layer separation on a cone at an angle of attack

Experimental data are obtained on the position of the line of separation as a function of angle of attack, cone apex angle, and flow Mach number.