负载水溶性铑－膦配合物催化1－己烯氢甲酰化反应的研究

将水溶性铑－膦配合物Ｒｈｃｉ（ＣＯ）（ＴＰＰＴＳ）＿２（ＴＰＰＴＳ：Ｐ－（ｍ－Ｃ＿６Ｈ＿４ＳＯ＿３Ｎａ）＿３）负载于扩孔硅胶上，制成负载水相催化剂（ＳＡＰＣ），在高压反应釜中研究其催化１－己烯氢甲酰化的性能。结果表明，催化剂的水含量对其活性影响很大，在一较窄的水含量范围内（２５—３５ｗｔ％），催化剂活性急剧增大，且存在一极大值，表现出水膜催化剂的特性。反应温度、总压和ＣＯ／Ｈ＿２分压、Ｒｈ／Ｐ比的影响，与使用烃溶性能。三苯膦络合催化剂时有类似规律，溶剂的影响不明显，实验证明，ＳＡＰＣ具有良好催化活性，ＳｉＯ＿２上负载的铑配合物不会被原料和产物洗提而造成流失，有利于催化剂的稳定和重复使用。     

超高比表面炭载钼煤气甲烷化催化剂

以沥青中间相为原料，氢氧化钾直接活化，获得了比表面达２３６３ｍ￣２／ｇ的超高比表面炭分子筛（ＣＭＳ）。分别以ＣＭＳ、ＳｉＯ＿２、活性炭和θ－Ａｌ＿２Ｏ＿３为担体，制备了负载钼催化剂，并研究其加压甲烷化反应性能，发现活性依下面顺序增加：θ－Ａｌ＿２Ｏ＿３＜ＳｉＯ＿２＜活性炭（ＡＣ）＜ＣＭＳ。还分别以钼酸铵和磷钼酸（ＨＰＭｏ）为前驱体，制备了ＣＭＳ负载钼催化剂，并考察了其煤气甲烷化活性，发现不同的催化剂前驱体对催化剂反应活性影响很大。根据产物中ＣＨ＿４／ＣＯ＿２的变化，推测ＣＯ在钼催化剂上的甲烷化反应包括如下两个步骤：（１）３Ｈ＿２＋ＣＯ→ＣＨ＿４＋Ｈ＿２Ｏ，（２）ＣＯ＋Ｈ＿２Ｏ→ＣＯ＿２＋Ｈ＿２。     

CoMoK／γ－Al_2O_3水煤气变换催化剂的硫化及反硫化

以Ｈ＿２Ｓ和ＣＳ＿２作硫化剂，用ＴＰＳ和ＴＰＤＳ方法研究了水媒气变换催化剂ＣｏＭｏＫ／γ－Ａｌ＿２Ｏ＿３的硫化及反硫化过程。用Ｈ＿２Ｓ／Ｈ＿２硫化时，只发现Ｈ＿２Ｓ的消耗和Ｈ＿２Ｏ的生成，用ＣＳ＿２／Ｈ＿２硫化时，首先生成ＣＯ＿２，然后是ＣＨ＿４，Ｈ＿２Ｏ和Ｈ＿２Ｓ，ＴＰＧ实验表明催化剂表面上有积炭，造成催化剂的活性降低。但积炭在水煤气变换反应进行中逐渐除去。ＴＰＤＳ实验表明Ｎ＿２不起反硫化作用，Ｈ＿２和ＣＯ也没有明显反硫化作用，Ｈ＿２Ｏ对ＣｏＭｏＫ／γ－Ａｌ＿２Ｏ＿３催化剂有根强的反硫化作用。Ｏ＿２能使催化剂部分永久性失活。ＸＰＳ测试表明反硫化的催化剂中低价的Ｍｏ￣（４＋）转变成高价的Ｍｏ￣（５＋）和Ｍｏ￣（６＋），导致其活性下降。     

水溶性铑－膦配合物催化长链烯烃氢甲酰化反应研究──反应条件的影响

本文研究了两相催化体系中，在ＣＴＡＢ（Ｃ＿（１６）Ｈ＿（３３）ＮＭｅ＿３Ｂｒ）存在下，水溶性铑－膦配合物ＲｈＣｌ（ＣＯ）（ＴＰＰＴＳ）＿２对１－己烯氢甲酰化反应的催化性能，详细考察了反应温度、压力、膦／铑比等对催化活性的影响。结果表明，在１．０ＭＰａ恒压下，反应温度１００℃，膦／铑摩尔比为１６，Ｈ＿２：ＣＯ＝１：１的条件下，１－己烯氢甲酰化的转化频率（ＴＯＦ）可达到３９．８ｍｉｎ￣（－１）。在此反应条件下，有机相和水相容易分离，铑－膦配合物流失到有机相中的量极小。     

低碳醇合成Raney Cu－Co催化剂的研究Ⅰ．反应性能考察

本文在５６３Ｋ、６ＭＰａ及Ｈ＿２／ＣＯ＝２的条件下，考察了Ｃｕ／Ｃｏ比不同的几个ＲａｎｅｙＣｕ－Ｃｏ催化剂的反应性能。结果表明：ＲａｎｅｙＣｕ－Ｃｏ催化剂上ＣＯ加氢产物主要为Ｃ＿１－Ｃ＿６正构醇及Ｃ＿１－Ｃ＿８正构烃。烃和醇产品的分布均符合Ｓｃｈｕｌｚ－Ｆｌｏｒｙ方程。但醇产品的链增长几率（０．３－０．５５）均小于烃产品的值（０．６－０．７５）。Ｃｕ／Ｃｏ比不同的催化剂在进入活性稳定区之前，均经过了一个不尽相同的活性波动区，活性趋于稳定所需时间随Ｃｕ／Ｃｏ比增大而缩短。Ｃｕ／Ｃｏ＝０．３－１．５（原子比）时，就醇收率而言，ＲａｎｅｙＣｕ－Ｃｏ催化剂明显高于共沉淀Ｃｕ－Ｃｏ催化剂，Ｃｕ／Ｃｏ＝０．８（原子比）时，稳定醇收率达０．５７ｇ·ｇ￣（－１）·ｈ￣（－１）。     

浆态床FT合成／固定床ZSM－5改质的合成液体燃料工艺的研究和开发

从合成气制取液体燃料的浆态床ＦＴ合成／固定床２ＳＭ－５改质的反应系统由Ⅰ段鼓泡浆液反应器（内径４０ｍｍ，高４５０Ｏｍｍ）和Ⅱ段固定床ＺＳＭ－５反应器（内径４０ｍｍ，高９００ｍｍ）组成，在温度２５０～２８０℃（Ⅰ段），３００～３４０℃（Ⅱ段），压力１．５～２．５ＭＰａ，空速２．０ＮＬ／ｇＦｅ·ｈ（Ⅰ段），５００～１０００ｈ￣－１（Ⅱ段），Ｈ＿２ＣＯ比０．５～１．５和气速１～２ｃｍ／ｓ范围内，考察了工艺参数对反应性能的影响，１０００ｈ以上的寿命试验的平均结果为：合成气单程转化率６５．１％，产率１００ｇ／Ｎｍ￣３（Ｃｏ＋Ｈ＿２），总烃生产达３５０ｇ／Ｆｅ。使用富ＣＯ合成气时，达１１０ｇ／Ｎｍ￣３（ＣＯ＋Ｈ＿２）。实测的ＦＴ合成反应热为２９３８；５ｋＪ／Ｎｍ￣３（ＣＯ＋Ｈ＿２）。长期运转试验表明，工艺流程合理，设备操作和温度控制可靠。采用的浆液循环回路方法可初步分离蜡中的催化剂。     

无定形（磷酸氢－二苯基次膦酸）锆－氯化铁复合物催化烷基化反应

制得无定形（磷酸氢－二苯基次膦酸）锆－氯化铁复合物Ｚｒ（ＨＰＯ＿４）＿（１．５）［Ｏ＿２Ｐ（Ｃ＿６Ｈ＿５）＿２］·［ＦｅＣｌ＿２（ＯＨ）］．该复合物不易吸潮，不冒烟，在空气中稳定，对卤代烷与芳香烃在液相的烷基化反应有较好的催化活性；反应条件温和，产物收率高，操作方便，后处理简单，并可多次重复使用。     

合成气制低碳烯烃K－Fe－MnO／MgO催化剂的研究Ⅰ．MnO助剂的作用

采用ＣＯ加氢反应、ＣＯ－ＴＰＤ、ＣＯ／Ｈ＿２－ＴＰＳＲ及Ｃ＿２Ｈ＿４／Ｈ＿２－ＴＰＳＲ等手段，研究合成气制低碳烯烃反应Ｋ－Ｆｅ－ＭｎＯ／ＭｇＯ催化剂中ＭｎＯ的助剂作用。结果表明ＭｎＯ能大幅度提高低碳烯烃的选择性，尤其是乙烯的选择性；ＭｎＯ能抑制催化剂表面的乙烯加氢，因而有利于提高低碳烯烃的选择性及烯／烷的比值。     

固相配位化学反应的研究LXⅧ．2－氨基嘧啶与Cu（Ⅱ）盐的固－固相化学反应

室温或近室温条件下，２－氨基嘧啶（ＡＰ）与４种铜（Ⅱ）盐ＣｕＣｌ＿２·２Ｈ＿２Ｏ、ＣｕＢｒ＿２、ＣｕＳＯ＿４·５Ｈ＿２Ｏ、ＣｕＡｃ＿２·Ｈ＿２Ｏ发生固－固相化学反应，生成３类不同配位比（Ｃｕ／ＡＰ分别为２：２、１：１和１：２）的２－氨基嘧啶合铜配合物。用元素分析、碘量法、电感耦合等离子直读光谱（ＩＣＰ）、ＩＲ、ＸＲＤ、ＵＶ、ＥＳＲ等方法表征了固相反应产物。不同阴离子铜盐的结构是影响固相反应的主要原因。讨论了固相反应的过程。反应沿晶格结构变化最小（活化能最低）的途径进行。     

Fe－P－O系催化剂上的甲烷氧化偶联

研究了Ｆｅ－Ｐ－Ｏ催化剂对甲烷氧化偶联（ＯＣＭ）的低温催化活性，考察了催化剂组分的优化，最适宜的反应温区，反应过程参数，助催化剂组分，催化剂的晶型结构和活性相以及Ｆ：元素键合状态的ＸＰＳ谱．确定了８％ＬｉＮＯ３－０．８Ｆｅ／Ｐ催化剂在６５０℃，ＣＨ４：Ｏ２：Ａｒ＝２：１：２及ＧＨＳＶ＝３０００ｈ－１条件下，可获得甲烷转化率为１１．９０％和Ｃ２烃选择性为６９．８１％的结果．添加ＬｉＮＯ３为助催成分，可有效改善催化剂表面酸活性中心的分布，防止ＯＣＭ中深度氧化和表面积炭，提高Ｃ２和Ｃ２烃选择性．该催化剂为可变价型，是六方形和料方形两种晶型结构的复合磷酸铁，活性相为斜方形ＦｅＰＯ４物相．     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.