PEO-LiClO4-ZSM5复合聚合物电解质 I. 电化学研究

首次以“择形”分子筛ZSM5为填料, 通过溶液浇铸法制得PEO-LiClO₄-ZSM5全固态复合聚合物电解质(CPE)膜. 交流阻抗实验表明ZSM5的引入可以显著地提高CPE的离子电导率. 利用交流阻抗-稳态电流相结合的方法对CPE的锂离子迁移数进行了测定, 结果表明掺入ZSM5后锂离子迁移数明显升高. ZSM5的含量为10%时, CPE同时具有最高离子电导率1.4×10^－5 S•cm^－1(25 ℃)和最大锂离子迁移数0.353. PEO-LiClO₄-ZSM5/Li电极界面稳定性实验表明PEO-LiClO₄-ZSM5复合聚合物电解质在全固态锂离子电池领域具有良好的应用前景.     

Nanocomposite solid polymeric electrolyte of 49% poly(methyl methacrylate)-grafted natural rubber�Ctitanium dioxide�Clithium tetrafluoroborate (MG49-TiO2-LiBF4)

A nanocomposite polymer electrolyte consisting of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) as a polymer matrix, lithium tetrafluoroborate (LiBF₄) as a dopant salt, and titanium dioxide (TiO₂) as an inert ceramic filler was prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by a sol?Cgel process. The ionic conductivity was investigated by alternating current impedance spectroscopy. X-ray diffraction (XRD) was used to determine the structure of the electrolyte, and its morphology was examined by scanning electron microscopy (SEM). The highest conductivity, 1.4?×?10^?5 S cm^?1 was obtained at 30 wt.% of LiBF₄ salt addition with 6 wt.% of TiO₂ filler content. Ionic conductivity was found to increase with the increase of salt concentration. The optimum value of conductivity was found at 6 wt.% of TiO₂. The XRD analysis revealed that the crystalline phase of the polymer host slightly decreased with the addition of salt and filler. The SEM analysis showed that the smoother the surface of the electrolyte, the higher its conductivity.     

Influence of barium titanate nanofiller on PEO/PVdF-HFP blend-based polymer electrolyte membrane for Li-battery applications

Organic-inorganic hybrid membranes based on poly(ethylene oxide) (PEO) 6.25 wt%/poly(vinylidene fluoride hexa fluoro propylene) [P(VdF-HFP)] 18.75 wt% were prepared by using various concentration of nanosized barium titanate (BaTiO₃) filler. Structural characterizations were made by X-ray diffraction and Fourier transform infrared spectroscopy, which indicate the inclusion of BaTiO₃ in to the polymer matrix. Addition of filler creates an effective route of polymer-filler interface and promotes the ionic conductivity of the membranes. From the ionic conductivity results, 6 wt% of BaTiO₃-incorporated composite polymer electrolyte (CPE) showed the highest ionic conductivity (6 × 10^?3 Scm^?1 at room temperature). It is found that the filler content above 6 wt% rendered the membranes less conducting. Morphological images reveal that the ceramic filler was embedded over the membrane. Thermogravimetric and differential thermal analysis (TG-DTA) of the CPE sample with 6 wt% of the BaTiO₃ shows high thermal stability. Electrochemical performance of the composite polymer electrolyte was studied in LiFePO₄/CPE/Li coin cell. Charge-discharge cycle has been performed for the film exhibiting higher conductivity. These properties of the nanocomposite electrolyte are suitable for Li-batteries.     

Nanocomposite solid polymeric electrolyte of 49% poly(methyl methacrylate)-grafted natural rubber–titanium dioxide–lithium tetrafluoroborate (MG49-TiO2-LiBF4)

A nanocomposite polymer electrolyte consisting of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) as a polymer matrix, lithium tetrafluoroborate (LiBF₄) as a dopant salt, and titanium dioxide (TiO₂) as an inert ceramic filler was prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by a sol–gel process. The ionic conductivity was investigated by alternating current impedance spectroscopy. X-ray diffraction (XRD) was used to determine the structure of the electrolyte, and its morphology was examined by scanning electron microscopy (SEM). The highest conductivity, 1.4 × 10⁻⁵ S cm⁻¹ was obtained at 30 wt.% of LiBF₄ salt addition with 6 wt.% of TiO₂ filler content. Ionic conductivity was found to increase with the increase of salt concentration. The optimum value of conductivity was found at 6 wt.% of TiO₂. The XRD analysis revealed that the crystalline phase of the polymer host slightly decreased with the addition of salt and filler. The SEM analysis showed that the smoother the surface of the electrolyte, the higher its conductivity.

     

Conductivity,structure, and thermal properties of chitosan‐based polymer electrolytes with nanofillers

This paper focus on the effect of nanosize (<50 nm BET) inorganic alumina (Al₂O₃) filler on the structural, conductivity, and thermal properties of chitosan‐based polymer electrolytes. Films of chitosan and its complexes were prepared using solution‐casting technique. Different amounts of Al₂O₃ viz., 3, 4.5, 6, 7.5, 9, 12, and 15 wt% were added to the highest room temperature conducting sample in the chitosan–salt system, i.e. sample containing 60 wt% chitosan–40 wt% NH₄SCN. The conductivity value of the sample is 1.29 × 10^?4 S cm^?1. On addition of 6 wt% Al₂O₃ filler the ionic conductivity increased to 5.86 × 10^?4 S cm^?1. The amide and amino peaks in the spectrum of chitosan at 1636 and 1551 cm^?1, respectively, shift to lower wavenumbers on addition of salt. The glass transition temperature T_g for the highest conducting composite is 190°C. The increase in T_g with increase in more than 6 wt% filler content is attributed to the increase in degree of crystallinity as proven from X‐ray diffraction studies. Copyright © 2009 John Wiley & Sons, Ltd.     

Effect of plasticizers (EC or PC) on the ionic conductivity and thermal properties of the (PEO)9LiTf: Al2O3 nanocomposite polymer electrolyte system

A new plasticized nanocomposite polymer electrolyte based on poly (ethylene oxide) (PEO)-LiTf dispersed with ceramic filler (Al₂O₃) and plasticized with propylene carbonate (PC), ethylene carbonate (EC), and a mixture of EC and PC (EC+PC) have been studied for their ionic conductivity and thermal properties. The incorporation of plasticizers alone will yield polymer electrolytes with enhanced conductivity but with poor mechanical properties. However, mechanical properties can be improved by incorporating ceramic fillers to the plasticized system. Nanocomposite solid polymer electrolyte films (200–600 μm) were prepared by common solvent-casting method. In present work, we have shown the ionic conductivity can be substantially enhanced by using the combined effect of the plasticizers as well as the inert filler. It was revealed that the incorporating 15 wt.% Al₂O₃ filler in to PEO: LiTf polymer electrolyte significantly enhanced the ionic conductivity [σ _RT (max)?=?7.8?×?10^?6 S cm^?1]. It was interesting to observe that the addition of PC, EC, and mixture of EC and PC to the PEO: LiTf: 15 wt.% Al₂O₃ CPE showed further conductivity enhancement. The conductivity enhancement with EC is higher than PC. However, mixture of plasticizer (EC+PC) showed maximum conductivity enhancement in the temperature range interest, giving the value [σ _RT (max)?=?1.2?×?10^?4 S cm^?1]. It is suggested that the addition of PC, EC, or a mixture of EC and PC leads to a lowering of glass transition temperature and increasing the amorphous phase of PEO and the fraction of PEO-Li⁺ complex, corresponding to conductivity enhancement. Al₂O₃ filler would contribute to conductivity enhancement by transient hydrogen bonding of migrating ionic species with O–OH groups at the filler grain surface. The differential scanning calorimetry thermograms points towards the decrease of T _g , crystallite melting temperature, and melting enthalpy of PEO: LiTf: Al₂O₃ CPE after introducing plasticizers. The reduction of crystallinity and the increase in the amorphous phase content of the electrolyte, caused by the filler, also contributes to the observed conductivity enhancement.     

Investigation on the effect of nanosilica towards corn starch–lithium perchlorate-based polymer electrolytes

Biodegradable corn starch–lithium perchlorate (LiClO₄)-based solid polymer electrolytes with addition of nano-sized fumed silica (SiO₂) were prepared by solution casting technique. Ionic conductivity at ambient temperature was measured by AC impedance spectroscopy. Upon addition of nano-sized SiO₂, the ionic conductivity at room temperature is increased. The optimum ionic conductivity value obtained was 1.23?×?10^?4?S?cm^?1 at 4?wt% SiO₂. This may be attributed to the low crystallinity of the polymer electrolytes resulting from the dispersed nanosilica particles. Fourier–transform infrared spectroscopy studies confirmed the complexation between corn starch, lithium perchlorate, and silica. The thermal properties of the prepared samples were investigated with differential scanning calorimetry and thermogravimetric analysis. The surface morphology of the polymer electrolytes confirmed the agglomeration of particles after excess dispersion of inorganic filler. This was proven in the scanning electron microscopy studies.     

Electrochemical properties of PEO/PMMA blend-based polymer electrolytes using imidazolium salt-supported silica as a filler

In this study, the composite polymer electrolytes (CPEs) were prepared by solution casting technique. The CPEs consisted of PEO/PMMA blend as a host matrix doped with LiClO₄. Propylene carbonate (PC) was used as plasticizer and a small amount of imidazolium salt-supported amorphous silica (IS-AS) as a filler was prepared by the sol–gel method. At room temperature, the highest conductivity was obtained for the composition having PEO–PMMA–LiClO₄–PC–4wt. % IS-AS with a value of 1.15 × 10^?4 S/cm. In particular, the CPE using the IS-AS filler showed a higher conductivity than any other sample (fumed silica, amorphous silica). Studies of differential scanning calorimetry and scanning electron microscopy indicated that the ionic conductivity increase was due to an expansion in the amorphous phase which enhances the flexibility of polymeric chains and the homogeneous structure of CPEs. It was found that the ionic conductivity and interfacial resistance stability of CPEs was significantly improved by the addition of IS-AS. In other words, the resistance stability and maximum ambient ionic conductivity of CPEs containing IS-AS filler were better than CPEs containing any other filler.     

Evaluating the electrochemical properties of PEO‐based nanofibrous electrolytes incorporated with TiO2 nanofiller applicable in lithium‐ion batteries

In the present work, nanofibrous composite polymer electrolytes consist of polyethylene oxide (PEO), ethylene carbonate (EC), propylene carbonate (PC), lithium perchlorate (LiClO₄), and titanium dioxide (TiO₂) were designed using response surface method (RSM) and synthesized via an electrospinning process. Morphological properties of the as‐prepared electrolytes were studied using SEM. FTIR spectroscopy was conducted to investigate the interaction between the components of the composites. The highest room temperature ionic conductivity of 0.085 mS.cm^?1 was obtained with incorporation of 0.175 wt. % TiO₂ filler into the plasticized nanofibrous electrolyte by EC. Moreover, the optimum structure was compared with a film polymeric electrolyte prepared using a film casting method. Despite more amorphous structure of the film electrolyte, the nanofibrous electrolyte showed superior ion conductivity possibly due to the highly porous structure of the nanofibrous membranes. Furthermore, the mechanical properties illustrated slight deterioration with incorporation of the TiO₂ nanoparticles into the electrospun electrolytes. This investigation indicated the great potential of the electrospun structures as all‐solid‐state polymeric electrolytes applicable in lithium ion batteries.     

Effect of solvated ionic liquids on the ion conducting property of composite membranes for lithium ion batteries

We prepared the polyethylene oxide (PEO)-based composite membrane electrolytes which contained the specialized ionic liquids and the inorganic filler of Li₇La₃Zr₂O₁₂ (LLZO). Mixtures of ionic liquids and tetragonal inorganic fillers were used as additives to prepare composite electrolytes for an application of all solid-state lithium ion batteries (ASLBs). In order to improve the ionic conductivity of composite membranes, we studied the structural change and the electrochemical behaviors as a function of the amounts of solvated ionic liquids (ILs). The addition effect of solvated ILs showed the higher ionic conductivity such as 10^?4 S/cm at 55 °C by reducing the crystalline character of polymer based composite, resulting in the enhanced ion conducting property. The hybrid composite membranes were successfully made in flexible form, and have an excellent thermal and electrochemical stability. Finally, the electrochemical performance of the half-cell was evaluated, and it was confirmed that the ion-conducting characteristics were influenced and controlled by the effect of ILs.     

Nanocomposite blend gel polymer electrolyte for proton battery application

A proton-conducting nanocomposite gel polymer electrolyte (GPE) system, [35{(25 poly(methylmethacrylate) (PMMA) + 75 poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP))?+?xSiO₂}?+?65{1 M NH₄SCN in ethylene carbonate (EC) + propylene carbonate (PC)}], where x?=?0, 1, 2, 4, 6, 8, 10, and 12, has been reported. The free standing films of the gel electrolyte are obtained by solution cast technique. Films exhibit an amorphous and porous structure as observed from X-ray diffractometry (XRD) and scanning electron microscopy (SEM) studies. Fourier transform infrared spectrophotometry (FTIR) studies indicate ion–filler–polymer interactions in the nanocomposite blend GPE. The room temperature ionic conductivity of the gel electrolyte has been measured with different silica concentrations. The maximum ionic conductivity at room temperature has been observed as 4.3?×?10^?3?S?cm^?1 with 2 wt.% of SiO₂ dispersion. The temperature dependence of ionic conductivity shows a typical Vogel-Tamman-Fulcher (VTF) behavior. The electrochemical potential window of the nanocomposite GPE film has been observed between ?1.6 V and 1.6 V. The optimized composition of the gel electrolyte has been used to fabricate a proton battery with Zn/ZnSO₄·7H₂O anode and PbO₂/V₂O₅ cathode. The open circuit voltage (OCV) of the battery has been obtained as 1.55 V. The highest energy density of the cell has been obtained as 6.11 Wh?kg^?1 for low current drain. The battery shows rechargeability up to 3 cycles and thereafter, its discharge capacity fades away substantially.     

PEO-LITFSI-SiO2-SN System Promotes the Application of Polymer Electrolytes in All-Solid-State Lithium-ion Batteries

All-solid-state polymer lithium-ion batteries are ideal choice for the next generation of rechargeable lithium-ion batteries due to their high energy, safety and flexibility. Among all polymer electrolytes, PEO-based polymer electrolytes have attracted extensive attention because they can dissolve various lithium salts. However, the ionic conductivity of pure PEO-based polymer electrolytes is limited due to high crystallinity and poor segment motion. An inorganic filler SiO₂ nanospheres and a plasticizer Succinonitrile (SN) are introduced into the PEO matrix to improve the crystallization of PEO, promote the formation of amorphous region, and thus improve the movement of PEO chain segment. Herein, a PEO₁₈−LiTFSI−5 %SiO₂−5 %SN composite solid polymer electrolyte (CSPE) was prepared by solution-casting. The high ionic conductivity of the electrolyte was demonstrated at 60 °C up to 3.3×10⁻⁴ S cm⁻¹. Meanwhile, the electrochemical performance of LiFePO₄/CSPE/Li all-solid-state battery was tested, with discharge capacity of 157.5 mAh g⁻¹ at 0.5 C, and capacity retention rate of 99 % after 100 cycles at 60 °C. This system provides a feasible strategy for the development of efficient all-solid-state lithium-ion batteries.     

PVDF/PAN/SiO<Subscript>2</Subscript> polymer electrolyte membrane prepared by combination of phase inversion and chemical reaction method for lithium ion batteries

PVDF/PAN/SiO₂ polymer electrolyte membranes based on non-woven fabrics were prepared via introducing a chemical reaction into Loeb-Sourirajan (L-S) phase inversion process. It was found that physical properties (porosity, electrolyte uptake and ionic conductivity) and electrochemical properties were obviously improved. A favorable membrane structure with fully connective porous and uniform pore size distribution was obtained. The effects of PVDF/PAN weight ratio on the morphology, crystallinity, porosity, and electrochemical performances of membranes were studied. The optimized PVDF/PAN (70/30 w/w) (designated as M_pc30) polymer electrolyte membrane delivered excellent electrolyte uptake of 246.8 % and the highest ionic conductivity of 3.32 × 10^?3 S/cm with electrochemical stability up to 5.0 V (vs. Li/Li⁺). In terms of cell performance, the Li/M_pc30 polymer electrolyte/LiFePO₄ battery exhibited satisfactory electrochemical properties including high discharge capacity of 149 mAh/g at 0.2 C rate and good discharge performance at different current densities. The promising results reported here clearly indicated that PVDF/PAN/SiO₂ polymer electrolyte membranes prepared by the combination of phase inversion and chemical reaction method were promising enough to be applied in power lithium ion batteries.     

纳米氧化镍浓度对磁性准固态染料敏化太阳能电池的影响

以琼脂糖为聚合物基质,N-甲基-2-吡咯烷酮(NMP)为溶剂,磁性纳米氧化镍颗粒作为添加剂用于制备染料敏化太阳能电池(DSSC)的磁性聚合物电解质。通过SEM与离子电导率测试研究不同纳米氧化镍掺杂浓度对磁性聚合物电解质的影响,并对相应的染料敏化太阳能电池进行光电性能测试与电化学交流组抗谱(EIS)测试,结果表明:1.0wt%的纳米氧化镍掺杂浓度为最优掺杂浓度,在此浓度下聚合物电解质的表面形貌较为平整,同时电解质具备最高离子电导率(2.43×10-3S.cm-1);染料敏化太阳能电池的光电效率与电子寿命均随着纳米氧化镍掺杂浓度的增加而先增加后降低,并都在纳米氧化镍掺杂浓度为1.0wt%达到最大,此时电池的光电效率为1.63%、开路电压为0.57 V、短路电流密度为5.8 mA.cm-2、填充因子为0.53。     

Electrochemical Performance of PEO10LiX-Li2TiO3 Composite Polymer Electrolytes

Introduction Recently, polymer electrolytes have attracted much attention for their potential use in replacing flammable organic solvent electrolytes currently used in lith-ium-ion batteries, thus improving the safety of re-chargeable lithium batteries. Moreover, the batteries with PE can be made in any shape, which make fully use of the space of electronic devices. PEO is a linear polymer with helix structure, and its structure makes it have much higher dissolution ability for salt even tho…     

Preparation and characterization of blended solid polymer electrolyte 49% poly(methyl methacrylate)-grafted natural rubber:poly(methyl methacrylate)–lithium tetrafluoroborate

The preparation and characterization of blended solid polymer electrolyte 49% poly(methyl methacrylate)-grafted natural rubber (MG49):poly(methyl methacrylate) (PMMA) (30:70) were carried out. The effect of lithium tetrafluoroborate (LiBF₄) concentration on the chemical interaction, structure, morphology, and room temperature conductivity of the electrolyte were investigated. The electrolyte samples with various weight percentages (wt.%) of LiBF₄ salt were prepared by solution casting technique and characterized by Fourier transform infrared spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical impedance spectroscopy. Infrared analysis demonstrated that the interaction between lithium ions and oxygen atoms occurred at symmetrical stretching of carbonyl (C=O) (1,735 cm^?1) and asymmetric deformation of (O–CH₃) (1,456 cm^?1) via the formation of coordinate bond on MMA structure in MG49 and PMMA. The reduction of MMA peaks intensity at the diffraction angle, 2θ of 29.5° and 39.5° was due to the increase in weight percent of LiBF₄. The complexation occurred between the salt and polymer host had been confirmed by the XRD analysis. The semi-crystalline phase of polymer host was found to reduce with the increase in salt content and confirmed by XRD analysis. Morphological studies by SEM showed that MG49 blended with PMMA was compatible. The addition of salt into the blend has changed the topological order of the polymer host from dark surface to brighter surface. The SEM analyses supported the enhancement of conductivity with the addition of salt. The conductivity increased drastically from 2.0 to 3.4?×?10^?5 S cm^?1 with the addition of 25 wt.% of salt. The increase in the conductivity was due to the increasing of the number of charge carriers in the electrolyte. The conductivity obeys Arrhenius equation in higher temperature region from 333 to 373 K with the pre-exponential factor σ _o of 1.21?×?10^?7 S cm^?1 and the activation energy E _a of 0.46 eV. The conductivity is not Arrhenian in lower temperature region from 303 to 323 K.     

Vibrational spectroscopy analysis of ion conduction mechanism in dispersed phase polymer nanocomposites

A novel combination of dispersed phase polymer nanocomposite electrolyte based on PEO₈‐LiClO₄+ x wt % nano‐CeO₂ has been investigated. A model for ion transport mechanism has been proposed to account for substantial enhancement of its electrical conductivity by ～ 2 orders of magnitude at low volume fraction of the filler reinforcement in the polymer nanocomposite films. The strength of the proposed model is based on unambiguous evidences from FTIR, TEM, and conductivity analysis. The FTIR results provide clear role of nanofiller concentration on ion–ion interaction quantified in terms of the fraction of free anion and ion‐pairs present in the nanocomposite films and its excellent correlation with conductivity versus filler concentration. The presence of asymmetry in the ν₄(ClO₄^?) band observed at 625 cm^?1 is attributed to its resolved degeneracy suggesting the presence of both uncoordinated and cation‐coordinated ClO₄^? anion in the matrix due to ion–ion and ion–filler interactions assisted by Lewis acid–base interaction. The enhancement in conductivity at low concentration is possibly due to direct interaction of nano‐CeO₂ with both polymer host and anions resulting in the release of ionic charges. Drastic conductivity reduction at higher concentration is related to charge immobilization because of ion/ion‐pair entrapment by local clusters of filler as evidenced in TEM. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 60–71, 2009     

A 3D Nanostructured Hydrogel‐Framework‐Derived High‐Performance Composite Polymer Lithium‐Ion Electrolyte

Solid‐state electrolytes have emerged as a promising alternative to existing liquid electrolytes for next generation Li‐ion batteries for better safety and stability. Of various types of solid electrolytes, composite polymer electrolytes exhibit acceptable Li‐ion conductivity due to the interaction between nanofillers and polymer. Nevertheless, the agglomeration of nanofillers at high concentration has been a major obstacle for improving Li‐ion conductivity. In this study, we designed a three‐dimensional (3D) nanostructured hydrogel‐derived Li_0.35La_0.55TiO₃ (LLTO) framework, which was used as a 3D nanofiller for high‐performance composite polymer Li‐ion electrolyte. The systematic percolation study revealed that the pre‐percolating structure of LLTO framework improved Li‐ion conductivity to 8.8×10^?5 S cm^?1 at room temperature.     

Improving electrochemical performance of poly(vinyl butyral)-based electrolyte by reinforcement with network of ceramic nanofillers

This study has concerned the development of polymer composite electrolytes based on poly(vinyl butyral) (PVB) reinforced with calcinated Li/titania (CLT) for use as an electrolyte in electrochemical devices. The primary aim of this work was to verify our concept of applying CLT-based fillers in a form of nano-backbone to enhance the performance of a solid electrolyte system. To introduce the network of CLT into the PVB matrix, gelatin was used as a sacrificial polymer matrix for the implementation of in situ sol–gel reactions. The gelatin/Li/titania nanofiber films with various lithium perchlorate (LiClO₄) and titanium isopropoxide proportions were initially fabricated via electrospinning, and ionic conductivities of electrospun nanofibers were then examined at 25 °C. In this regard, the highest ionic conductivity of 2.55 × 10⁻⁶ S/cm was achieved when 10 wt% and 7.5 wt% loadings of LiClO₄ and titania precursor were used, respectively. The nanofiber film was then calcined at 400 °C to remove gelatin, and the obtained CLT film was then re-dispersed in solvated PVB-lithium bis(trifluoromethanesulfonyl)imide (PVB-LiTFSI) solution before casting to obtain reinforced composite solid electrolyte film. The reinforced composite PVB polymer electrolyte film shows high ionic conductivity of 2.22 × 10⁻⁴ S/cm with a wider electrochemical stability window in comparison to the one without nanofillers.

     

Excellent Capacitive Performance of a Three‐Dimensional Hierarchical Porous Graphene/Carbon Composite with a Superhigh Surface Area

Three‐dimensional hierarchical porous graphene/carbon composite was successfully synthesized from a solution of graphene oxide and a phenolic resin by using a facile and efficient method. The morphology, structure, and surface property of the composite were investigated intensively by a variety of means such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), N₂ adsorption, Raman spectroscopy, and Fourier transform infrared spectroscopy (FTIR). It is found that graphene serves as a scaffold to form a hierarchical pore texture in the composite, resulting in its superhigh surface area of 2034 m²g^?1, thin macropore wall, and high conductivity (152 S m^?1). As evidenced by electrochemical measurements in both EMImBF₄ ionic liquid and KOH electrolyte, the composite exhibits ideal capacitive behavior, high capacitance, and excellent rate performance due to its unique structure. In EMImBF₄, the composite has a high energy density of up to 50.1 Wh kg^?1 and also possesses quite stable cycling stability at 100 °C, suggesting its promising application in high‐temperature supercapacitors. In KOH electrolyte, the specific capacitance of this composite can reach up to an unprecedented value of 186.5 F g^?1, even at a very high current density of 50 A g^?1, suggesting its prosperous application in high‐power applications.