Integrated retention/spectrophotometric detection in flow-injection analysis : Determination of Iron in Water and Wine

An integrated retention/spectrophotometric method is proposed for the determination of iron based on the Fe (III)-thiocyanate complex. The method has good selectivity, with a determination limit of 10 ng ml^?1 and a linear range of 10–400 ng ml^?1. Different types of measurements (peak height, absorbance increment, tangent curve) are shown to have their particular advantages. The method is applied to the determination of iron in natural water and wine, with an average recovery of 100.3% and 98.8% and an average deviation of the recovery of 2.5% and 1.6%, respectively.     

红枣中果糖、葡萄糖与蔗糖的高效液相色谱示差检测分析

建立了同时分析鲜红枣中果糖、葡萄糖和蔗糖的高效液相色谱方法.利用鲜红枣样品进行添加回收实验,获得方法对果糖、葡萄糖和蔗糖测定的平均回收率分别为93.5%、91.8%和89.8%,变异系数3.27%、2.34%、5.86%.结果表明:采用高效液相色谱示差分析方法定量检测鲜红枣中果糖、葡萄糖和蔗糖快速、简便.同时得出方法的检出限为:果糖5.73×10-3mg/mL,葡萄糖5.22×10-3mg/mL,蔗糖3.59×10-3mg/mL,测定结果符合食品检测要求.     

Flow Injection Spectrophotometric Determination of 2,4‐D Herbicide

2,4‐Dichlorophenoxy acetic acid herbicide is spectrophotometrically determined by diazotization method in a flow injection assembly. The method is based on base hydrolysis of herbicides. The hydrolyzed product 2,4‐dichlorophenol is reacted with diazotized sulfanilic acid. The absorbance of the resulting coloured product was measured at 480 nm. The calibration graph is linear over the range of 0.2–20 μgmL^?1, with a relative standard deviation of (RSD) of 7.2% and sample throughput of 90 samples h^?1. The % recovery for determination of 2,4‐dichlorophenoxy acetic acid was found to be 92.0–95.3%. The method is easy, simple and faster than the established chromatographic method. The method was applied for determination of 2,4‐dichlorophenoxy acetic acid herbicide in commercial formulations and for residue determination in fruits and food samples.     

Extractive Spectrqphotometric Determination of Vanadium Liith o-Aminobenzo-Hydroxamic Acid

Abstract

A new spectrophotometric method for vanadium determination is proposed. The method is based on the extraction in Adogen-toluene solution of the complex formed between V(V) and o-Aminobenzohydraxámic acid

The method allows determination of 50 to 110 μg of V(V). The error and the apparent molar absorptivity are 1.2% and 5.2 ± 10³ l.mol^?1. cm^?1 respectively. The interferences caused by foreign ions have been established. The method is applied with success to determination of vanadium in petroleum crudes.     

Automated flow-injection determination of sulfonamides by the bratton—marshall reaction for clinical analysis,assays and dissolution studies of formulations

The automated flow-injection determination described for sulfonamides (2–20 mg l^?1, 5×10^?4?5×10^?3 M) is based on the Bratton-Marshall reaction. Destruction of the excess of nitrous acid is not required and the measurement rate is 72 per hour. Precision is excellent. The method is applied for the determination of sulfonamides in control serum and urine samples, in feeds and in formulations (by using the pseudo-titration technique), and for automated dissolution studies of tablets. The method was evaluated by analyzing spiked sample solutions; the recoveries obtained were 94–101% for serum, 98–103% for urine, 98–105% for feeds and 96–105% for formulations. Comparison of the pseudo-titrimetric method for sulfonamide assays with the HPLC method gave a mean difference of 1.3%.     

Determination of Enzymatic Activities Based on an Optical Flow-Through p-Nitrophenol Sensor

Abstract

An optical flow-through biosensor based on the transient retention of p-nitrophenol on an ion-exchange support packed in the flow cell is presented. The approach was applied to the determination of the activity of some enzymes which catalyze the conversion of p-nitrophenyl-derivatives into p-nitrophenol. The method was first developed for determination of p-nitrophenol yielding a linear range between 0.1–5 μg/mL (r² = 0.9922, r.s.d.% less than 2.5), then, it was also applied to the determination of β-D-glucuronidase activity in serum, with a linear range between 0.1–20 U/L (r² = 0.9976, r.s.d.% less than 3.0), and a sampling frequency of 20 h^?1. The application of the method to the determination of the enzyme activity in serum samples provided results consistent with those obtained by a conventional method and recoveries within 95–104%.     

Neutron activation method for nitrogen determination in biological specimens

For the determination of the nitrogen content in plants, 14 MeV neutron activation analysis was used based on the determination of the elemental concentration by measuring the area of the gamma-radiation of the radionuclide¹³N as a result of¹⁴N(n, 2n)¹³N reaction. Three methods were tested in order to obtain quantitative results: comparator method, method for absolute determination of the neutron flux and monitor method. Using the monitor method, results for nitrogen content in plant species were obtained-for beans 74.8% and for maize 1.8%. The precision of determination is ±10%. The possible sources of errors are analyzed. The efficiency of the Ge(Li) detector has been determined using a combined -source in the energy interval 120–1400 keV with precision of 4.5%. The sensitivity achieved was 4 mg or 47 imp/mg per min.     

Trace determination of gaseous chlorine: a comparison between an electrometric method and the methyl orange photometric method

Two methods for the determination of molecular chlorine in air are critically compared. An electrometric method based on measurement of the reduction current of chlorine to chloride is superior to the photometric determination based on bleaching of an acidic solution of methyl orange. The limit of detection for the electrometric method is 50 μg m^-3; the standard error of the mean is better than 2%, and the sensitivity is 5.9 μg m^-3 μ A^-1 at +50 mV applied potential versus SCE with a mercury cathode. The limit of detection for the photometric method is 300 μg m^-3; the precision is of the order of 5%, and the sensitivity is 80 μg m^-3 for an error of 1% in the absorption measurements. The accuracy of the electrometric method is good whereas the photometric method yields consistently low results. The electrometric method is less subject to interferences than the photometric method.     

Square-wave cathodic adsorptive stripping voltammetric determination of trace amounts of 2-mercaptobenzimidazole in water samples

A sensitive, simple and reproducible square-wave cathodic adsorptive stripping voltammetric method is developed for the determination of 2-mercaptobenzimidazole (MBIM) in different water samples using a static mercury drop electrode (SMDE) as a working electrode. The solution conditions and instrumental parameters were optimized for the determination of MBIM by square-wave cathodic adsorptive stripping voltammetry. This method is based on a sensitive adsorptive reduction peak of the MBIM at ?0.532 V vs. Ag/AgCl reference electrode in a Britton-Robinson buffer at pH 10.0. The linear concentration range was 20–600 ng ml^?1 when using 0.0 V as the accumulation potential. The detection limit of the method was calculated to be 8.41 ng ml^?1. The precision was excellent with relative standard deviations (n = 20) of 2.30%, 1.71%, 2.25% and 1.33% at MBIM concentrations of 40, 90, 200 and 500 ng ml^?1, respectively. The proposed voltammetric method is used for the determination of MBIM in different spiked water samples.     

Determination of femtogram quantities of 239Pu and 240Pu in bioassay samples by thermal ionization mass spectrometry

Summary A thermal ionization mass spectrometry (TIMS) method is described for the determination of ultra-trace levels of plutonium isotopes in human urine samples. The method has been validated through the analysis of artificial urine samples spiked with known amounts of ²³⁹Pu ranging from 2.5 fg to 50 fg (6-115mBq). A slight positive bias of 1.7%-2.7% was determined, with a relative precision of 2.2% at 50 fg, increasing to 2.7% for 5-25 fg ²³⁹Pu. The detection limit of the method was 0.53 fg (1.2mBq) ²³⁹Pu, and the instrumental detection limit was at least 0.1 fg. The determination of the isotopic signature of the sample with ²³⁹Pu, ²⁴⁰Pu, and ²⁴¹Pu amounts of several femtograms is possible, and was demonstrated with the determination of the 240 to 239 ratio in an inter-laboratory sample comparison. The method is relatively free from interferences, 95% of sample preparations were acceptable both in terms of chemical recovery and lack of isobaric interference. The isotopic abundance of the ²⁴²Pu SRM 4334E of the National Institute of Standards and Technology (NIST) was also determined by TIMS and was found to be 99.99967 atom% ²⁴²Pu.     

Determination of strontium radioisotopes in soils

Summary A method is proposed for determination of radiostrontium in soils which is based on selective strontium separation by liquid-liquid extraction with dicyclohexano-18-crown-6 in chloroform, loading of the extract on a thin-layer plate and TLC separation of strontium and yttrium radioisotopes using a circular procedure. The method allows the separate determination of ⁸⁹Sr and ⁹⁰Sr. The strontium chemical yield is more than 90%, the detection limit is about 0.5 Bk/g, RSD is equal to 2–5%.     

PTFE capillary trap as a tool to monitor non-ionic surfactants in the aquatic environment

A method based on the separation of non-ionic surfactants (NS) in the PTFE capillary trap with final determination by the indirect adsorptive stripping tensammetry has been developed. The method is suitable for NS determination in river water, raw and treated sewage within the range of 2-10,000 μg l⁻¹. The sample volume varies between 0.1 and 50 ml depending on NS concentration, and the time necessary for a single determination is approximately 15 min. This is several orders of magnitude better than determination with the recommended BiAS method. In environmental samples, recoveries ranges from 81 to 95% and precision ranges from 3 to 10%.     

Determination of thorium and uranium in activated concrete by inductively coupled plasma mass spectrometry after anion-exchange separation

A sensitive analytical method was established for the determination of Th and U in activated concrete samples. The method combines an anion-exchange separation step with an ICP-MS determination technique. In the ICP-MS measurement, a few μg mL^–1 of Al and Ca, a few ng mL^–1 of Mn, La, Ce, Nd and Pb and pg mL^–1 amounts of Li, Zr, Nb and Ba coexisting in the anion-exchange fraction of Th and U did not interfere. No adverse interference effects were observed in real sample analyses. The obtained detection limits (3σ, n = 10) of Th and U were 2.3 and 1.8 pg mL^–1, respectively. The analytical precisions for ca. 5 μg g^–1 Th and ca. 1 μg g^–1 U in real activated concrete samples were equally less than 7% RSD. The accuracies obtained by the analysis of GSJ rock standard samples were –18.1 to 0.4% for the Th determination and –14.0 to –5.7% for the U determination. The method uses the conventional absolute calibration curve. The internal standard calibration is unnecessary.     

Studies on reaction of reduced lipoic acid with Mukaiyama reagent and its application for pharmaceutical and food analysis

A new sensitive method for the determination of lipoic acid (LA) in selected food items based on its reaction with Mukaiyama reagent (2-chloro-1-methylpyridinium iodide, CMPI) was developed. It was stated that CMPI reacts with reduced form of lipoic acid (dihydrolipoic acid, DHLA) and the stable product is produced. The spectrum of the labeled form of DHLA exhibits new band at 312?nm. Based on its spectral characteristics new spectrophotometric and UV–high-performance liquid chromatography (HPLC) methods of LA determination were elaborated. Both methods allowed determination of the analyte in the concentration range of 5?×?10^?6–1?×?10^?4?mol?L^?1 with limit of detection 0.39?×?10^?6 and 0.77?×?10^?6?mol?L^?1 for spectrophotometric and HPLC method, respectively. The practical usability of newly developed methods was checked by determination of lipoic acid contents in its pharmaceutical preparate Revitanerw. The proposed method was precise and accurate. The relative error of determination did not exceed ±0.067%. As chromatographic method allowed the determination of analyte in the presence of complex matrix, it was applied for assay of free fraction of α-lipoic acid in selected food items. A procedure of LA isolation from biological matrix was developed. The extraction with dichloromethane allowed quantitative recovery at 102.94?±?4.20%. The green barley appeared to be the richest source of LA.     

Spectrofluorimetric determination of trace amounts of thorium

A spectrofluorimetric method, based on the formation of a fluorescent complex with salicyladehyde carbohydrazone, is optimized for the determination of thorium (20–800 μg l^?1) at “pH” 1.3–1.7. The relative standard deviation is 2.7% for 100 μg Th l^?1. The method is applied to synthetic mixtures containing various amounts of thorium and to the determination of thorium in monazite samples.     

Simultaneous determination of ammonia and urea with an asymmetric merging zones/flow-injection configuration

A method is proposed for the simultaneous determination of urea and ammonia using a reagent-injection configuration that includes a dual injection valve (for insertion of Nessler's reagent and for accommodating the enzyme reactor). The resolution of the two peaks obtained on each injection allows the determination of both analytes in mixtures. The determination range is 1–5 μg ml^?1 for ammonia and 1–6 μg ml^?1 for urea, with relative standard deviations of 1.13% and 2.31% for ammonia (first and second peaks) and 1.86% for urea.     

Flow Injection with an Integrated Retention/Photometric Detection Unit for the Determination of Iron in Water

An integrated retention/photometric detection method for the determination of microamounts of iron was developed. The method is based on the retention of the reaction product of the analyte with ferrozine in a flow cell packed with an anion exchange support, and on the subsequent elution of the retained complex with a solution of 1.5% sodium peroxide, which allows the reuse of the system. The method is highly selective and has a detection limit (3σ) of 4.3 ng ml⁻¹. Iron was thus determined in the range 10–200 ng ml⁻¹with a relative standard deviation of 1–3% (n= 11). The method was applied to the determination of iron in tap and river water and the results were consistent (2%) with those provided by AAS.     

Gold and silver determination in Waters by SPHERON® Thiol 1000 preconcentration and ETAAS

A reliable procedure for the electrothermal atomic absorption spectrometry (ETAAS) determination of gold and silver in waters at trace level is described. The method is based on prior separation and preconcentration of the metals using a chelating sorbent SPHERON® Thiol 1000 after acidification of water samples (pH < 3) with nitric acid. Optimization of analytical variables during enrichment and ETAAS determination of the metals are discussed. The accuracy of the method is verified by analysis of certified reference materials. The limits of determinations based on 10 σ definition were 0.005 ng cm^?3 for Au and 0.02 ng cm^?3 for Ag. Precision of studied elements determination expressed by relative standard deviation varied in the range from 2.9 % to 16.4 %.     

Kinetic Spectrophotometric Determination of Ritodrine Hydrochloride in Dosage Forms

A simple and sensitive kinetic method was developed for the determination of ritodrine hydrochloride in pharmaceutical preparations. The method is based upon a kinetic investigation of the oxidation reaction of the drug with alkaline potassium permenganate at room temperature for a fixed 12.5 min; the absorbance of the colored permenganate ion was measured at 609 nm. The absorbance concentration plots were rectilinear over the range of 1.6–11.2 μg mL^?1 (r = 0.9992) with a minimum detectability of 0.096 μgmL^?1 (2.88 × 10^?7 M). The different experimental parameters affecting the development and stability of color were carefully studied and optimized. The determination of ritodrine hydrochloride by the fixed concentration and rate constant methods is also feasible with the calibration equations obtained, but the fixed time method has been found to be more applicable. The proposed method was applied successfully to the determination of ritodrine hydrochloride in tablets and ampoules with average recoveries of 100.37 ± 0.93% and 100.42 ± 0.87%, respectively. The results obtained were in good agreement with those obtained using a reference method for comparison. A proposal of the reaction pathway is also presented.     

A test for the reliability of the controlled potential coulometric method to determine plutonium in uranium-plutonium mixtures

Summary A method has been developed for the determination of trimethylsilyl groups in N-silylated compounds and in trimethylsilyl esters of carboxylic acids. The method is based on the desilylation of the compound to be analysed with phenol followed by gas-chromatographic determination of the trimethylphenoxysilane formed. The relative error of the determination is around 1% and the standard deviation is 1.20 × 10^–3 (3.12%). A single determination takes less than 2 h.

---

Gas-chromatographische Bestimmung von Trimethylsilyl-Gruppen in N-silylierten Verbindungen und in Trimethylsilyl-Estern von Carbonsäuren

Zusammenfassung Das Verfahren beruht auf der Desilylierung der zu analysierenden Verbindung mit Phenol und der anschlie\enden gas-chromatographischen Bestimmung des gebildeten Trimethylphenoxysilans. Der relative Fehler der Bestimmung beträgt ca. 1% und die Standardabweichung 1,20 × 10^–3 (3,12%). Die Bestimmungszeit ist kürzer als 2 h.