改性麦壳对水中苯酚的生物吸附作用

通过对农业副产物麦壳进行甲醛甲酸甲基化改性,研究了改性后麦壳对苯酚的吸附情况,讨论了吸附时间、吸附剂用量、初始浓度、温度及pH等条件对吸附效果的影响。结果表明,改性后的麦壳对苯酚的吸附反应迅速,随着吸附剂用量增加,吸附量增大;增大初始浓度,吸附量升高;升温对反应不利;酸性条件下有利于吸附。改性后的麦壳对苯酚的吸附符合Langmuir和Freundlich等温模型。改性麦壳可用于苯酚的去除。     

三乙烯四胺改性榴莲壳吸附水溶液中的Cd~(2+)、Pb~(2+)

采用三乙烯四胺改性榴莲壳,制备新型的改性榴莲壳吸附剂,研究其对Cd2+、Pb2+的吸附性能。结果表明,吸附Cd2+、Pb2+的适宜条件为:pH 6.0,吸附时间120 min。改性后榴莲壳吸附剂对Cd2+、Pb2+的吸附容量有了很大程度的提高,Cd2+、Pb2+最大吸附量分别达到39.30、53.76 mg/g。吸附过程可以很好地用准二级动力学方程描述,吸附等温线用Langmuir方程的拟合效果优于Freundlich方程。     

生物质竹炭对水中Cd~(2+)的吸附行为研究

以竹炭和经化学改性竹炭作为吸附剂,研究其对水溶液中Cd2+的吸附特性,探讨了竹炭对Cd2+的吸附热力学和吸附动力学性质,通过单因子优化实验探讨了温度、竹炭投加量和p H值对吸附效果的影响。结果表明:竹炭及改性竹炭对Cd2+的吸附动力学过程符合准二级动力学模型,在18h可达到平衡;其等温吸附曲线符合Langmuir方程,最大吸附量分别为10.18mg/g和16.71mg/g;两者对Cd2+的吸附受温度的影响较小;竹炭及改性竹炭的最佳投加量分别为0.8g、0.6g;p H对竹炭及改性竹炭吸附Cd2+的影响较大,在p H 2~6范围时,竹炭及改性竹炭对Cd2+的吸附量随p H的增加而增加。     

微波改性活性炭用于烟气脱硫脱硝的实验研究

在用浓硝酸、氢氧化钾化学改性活性炭的基础上,使用专门设计的微波发生器对活性炭进行热处理,制备了一种高效的活性炭吸附剂用于烟气脱硫脱硝。改性活性炭对模拟烟气的吸附实验表明,活性炭经微波改性后的脱硫吸附量明显提高,氢氧化钾浸泡加微波改性的脱硫效果最好,浓硝酸浸泡加微波改性的活性炭对氮氧化物也有比较好的吸附效果,NO的吸附容量可达到36.8×10-3。扫描电镜(SEM)显示,微波改性后的活性炭微孔充分,有利于污染物的脱除。此外,还对各种改性方法提高活性炭脱硫脱硝性能的机理进行了分析。     

改性介孔材料SBA-15对甲基丙烯酸甲酯与苯乙烯的吸附与释放研究

考察了不同偶联剂改性的介孔材料SBA-15对甲基丙烯酸甲酯(MMA)和苯乙烯(St)的吸附与释放性能,研究了在室温条件下的吸附与释放动力学行为。结果表明,偶联剂的表面改性使介孔材料对MMA和St的饱和吸附量明显降低,而吸附率与释放率升高;介孔材料释放速率先快后慢,释放量最后趋于平衡;改性介孔材料SBA-15对吸附质吸附行为符合准二级吸附动力学方程,释放行为符合一级释放动力学方程。最大释放量实验值与拟合的理论值较为吻合。介孔材料对St的释放时间要远长于MMA。     

有机改性凹凸棒土对腐殖酸的吸附性能研究

合成了十六烷基三甲基氯化铵(CTAC)改性的凹凸棒土吸附剂,并研究了其对水中腐殖酸的吸附行为。通过FTIR、TG对改性前后凹凸棒土进行表征。结果表明,十六烷基三甲基氯化铵成功结合到凹凸棒土表面,结合到凹凸棒土表面的量为9.78%。在25℃时,腐殖酸在吸附剂上吸附行为符合Freundlich方程,吸附动力学符合拟二级动力学方程,初始浓度为54.60~200.20mg/L时,ATP-CTAC对腐殖酸的最大吸附量为253mg/g;温度对吸附行为影响不大;改性后的凹凸棒土对腐殖酸的吸附随pH的增大而降低;改性后的凹凸棒土显著地提高了对腐殖酸的吸附量。     

甲醇与异丁烯在改性β分子筛上的吸附行为研究

采用过渡应答技术对甲醇和异丁烯在改性β分子筛上的吸附行为进行了研究,研究结果表明：异丁烯和甲醇有改性β分子筛上符合先快吸附后慢吸附的Elovich吸附规律。甲醇的吸附量大,但速率慢,异丁烯吸附量小,速率快;由于甲醇的饱和吸附量大于异下烯的饱和吸附量,对合成MTBE反应的选择性具有重要意义。对它们的吸附行为进行动力学研究,得到不同温度下吸附活化能随吸附量变化的关系。不同温度下相对饱和吸附量预测表明：当温度从288K升高到383K时,qMeOH/qIB从6．1降低到4．6,甲醇的相对饱和吸附量随温度升高而减小,但仍保持较高值,证明了甲醇在分子筛上是强吸附的观点,为解释选择性和高和动力学方程的建立提供依据,对反应机理的研究有指导作用。     

甲醇与异丁烯在改性β分子筛上的吸附行为研究

采用过渡应答技术对甲醇和异丁烯在改性β分子筛上的吸附行为进行了研究,研究结果表明,异丁烯和甲醇在改性β分子筛上符合先快吸附后慢吸附的Elovich吸附规律。甲醇的吸附量大,但速率慢;异丁烯吸附量小,速率快。由于甲醇的饱和吸附量大于异丁烯的饱和吸附量,对合成MTBE反应的选择性具有重要意义,对它们的吸附行为进行动力学研究,得到了不同温度下吸附活化能随吸附量变化的关系。不同温度下相对饱和吸附量预测表明：当温度从288K升高到383K时,qMeOH/q1BWW 6．1降低到4．6,甲醇的相对饱和吸附量随温度升高而减小,但仍保持较高值,证明了甲醇在分子筛上是强吸附的观点,为解释选择性高和动力学方程的建立提供依据,对反应机理的研究有指导作用。     

改性纤维素的制备及分光光度法对Cu~(2+)吸附研究

针对日益严重的铜离子污染问题,以化学浆纤维素为原料,通过氨基酸接枝修饰2,2,6,6-四甲基哌啶氧自由基(TEMPO)氧化体系氧化的纤维素,制备出一种新型吸附剂,并采用灵敏简便的分光光度法研究改性对铜离子的吸附效果。结果表明,氨基酸修饰纤维素(AMC)与TEMPO氧化纤维素(TOC)相比,对铜离子的吸附效果有不同程度的提升,其中组氨酸改性的吸附效果最好,低浓度时吸附率可以高达97%。随着浓度增大,吸附率下降,但是吸附量增大,当吸附200 mg/L的Cu2+溶液时,吸附量可达47 mg/g。此外,研究了不同条件下AMC对Cu2+的吸附情况,包括AMC投加量、初始浓度、pH值等。结果表明,吸附过程的吸附模型符合Langmuir等温模型,吸附动力学可以用准二级吸附动力学方程拟合。     

改性介孔材料SBA-15对水、甲苯和单体混合物的吸附和释放研究

以不同类型的硅烷偶联剂对自制的介孔分子筛SBA-15进行了改性,研究了改性介孔材料SBA-15对水、甲苯和双环戊二烯(DCPD)/苯乙烯(St)(DCPD/St=9/1,体积比)单体混合液(DS)的吸附和释放性能。研究发现,改性前,SBA-15吸附水和甲苯的量相差不大,而吸附单体混合物量较多;使用硅烷偶联剂改性后,吸附量均下降,但是吸附速率提高,吸附量较小者吸附速度较快。介孔材料对甲苯的释放速率是对水和DS的100倍左右,改性介孔材料提高了对吸附质的释放速率;吸附和释放均符合准二级吸附动力学方程。     

Adsorption of Basic Dyes Using Walnut Shell-based Biochar Produced by Hydrothermal Carbonization

Hydrothermal carbon(HC) was prepared from walnut shells, which are abundant in Northeastern China. The prepared HC was used as a precursor to produce nitric acid modified carbon(MC). The hydrothermal carbonization included dehydration and decarboxylation processes wherein the hemicellulose was completely decomposed and the cellulose was partly decomposed, with some oxygen-containing functional groups being produced. The aromati-city, specific surface area and pore content of the HC increased, but its polarity decreased. With 6 mol/L nitric acid and a modification time of 15 min, the specific surface area and pore content decreased, but the proportion of oxygen-containing functional groups on the surface increased significantly, thereby improving the dye adsorption performance. The adsorption of methylene blue and malachite green was best described by the pseudo-second-order kinetic and Langmuir isotherm models. The adsorption capacity of MC was determined to be much larger than that of HC.     

Electrochemical Preparation of Poly(Malachite Green) Film Modified Nafion‐Coated Glassy Carbon Electrode and Its Electrocatalytic Behavior Towards NADH,Dopamine and Ascorbic Acid

Poly(malachite green) film modified Nafion‐coated glassy carbon electrodes have been prepared by potentiodynamic cycling in malachite green solution. The pH of polymerisation solution has only minor effect on film formation. Electrochemical quartz crystal microbalance (EQCM) was used to monitor the growth of the poly(malachite green) film. Cyclic voltammogram of the poly(malachite green) film shows a redox couple with well‐defined peaks. The redox response of the modified electrode was found to be depending on the pH of the contacting solution. The peak potentials were shifted to a less positive region with increasing pH and the dependence of the peak potential was found to be 56 mV per pH unit. The electrocatalytic behavior of poly(malachite green) film modified Nafion‐coated glassy carbon electrodes was tested towards oxidation of NADH, dopamine, and ascorbic acid. The oxidation of dopamine and ascorbic acid occurred at less positive potential on poly(malachite green) film compared to bare glassy carbon electrode. In the case of NADH, the overpotential was reduced substantially on modified electrode. Finally, the feasibility of utilizing poly(malachite green) film electrode in analytical estimation of ascorbic acid was demonstrated in flow injection analysis.     

Preparation of Corn Stalk-Walnut Shell Mix-based Activated Carbon and Its Adsorption of Malachite Green

The mix-based activated carbon derived from corn stalk and walnut shell was prepared by chemical activation method using phosphoric acid as the activator. The optimized conditions for preparation were obtained by the orthogonal experiment, the characterizations of the activated carbon were performed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy(FTIR), Boehm's titration method and nitrogen adsorption. For the prepared mix-based activated carbon, the highest iodine number, methylene blue number and BET surface area are 720.5 mg/g, 195.0 mg/g and 1187 m²/g, respectively, and the pores are mainly mesopores. The mix-based activated carbon shows the higher adsorption capacity for malachite green than the raw materials, the activated carbons prepared only from corn stalk or walnut shell and the commercial activated carbon. The kinetics and thermodynamics of the adsorption can be satisfactorily described by the pseudo-second-order kinetic model and the Langmuir isotherm model, separately.     

化学法沉积银岛膜上的表面增强拉曼散射(Ⅰ)

用银镜反应在抛光的石英片上沉积银膜,经扫描电镜研究表明,控制反应条件可得到表面粒度为50～140nm的SERS活性银岛膜表面,将此活性表面直接插入含微量孔雀石绿水溶液中,测量吸附孔雀石绿分子的拉曼光谱,可获得10⁵倍的拉曼增强,孔雀石绿浓度小到10^-10mol/L时,仍能得到明确的光谱信息,给出了浓度与强度的关系,讨论了吸附作用对几个重要振动带的影响。     

基于金属有机框架水凝胶的一步式快速富集检测养殖水体中孔雀石绿北大核心CSCD

孔雀石绿是一种三苯甲烷类化合物,在水产品饲养中对疾病的防治有着不错的疗效,但因对人体健康有危害而被列为禁用药。由于实际样品中成分复杂,对于此类染料的检测方法难以同时兼具富集性好、灵敏度高且方便快速的优点。该工作制备了金属有机框架材料(MOF),采用MOF纳米材料掺杂的水凝胶(PAAM-SA/MOF)对养殖水体中的孔雀石绿进行吸附研究。采用一系列表征手段对MOF、PAAM-SA和PAAM-SA/MOF的微观形貌进行分析,结果表明吸附材料已成功合成。通过优化水凝胶吸附剂用量、吸附时间、孔雀石绿溶液pH、吸附温度、孔雀石绿溶液初始浓度等吸附萃取条件,使溶液中的孔雀石绿基本完全吸附在水凝胶中,在最优条件下,吸附效率最高可达97%。此外,采用不同极性的有机溶剂对吸附的孔雀石绿进行洗脱,通过优化洗脱液体积,脱附率最高达99%。在最佳条件下,该方法在高、中、低3个水平下的样品加标回收试验中回收率达到84.8%~118.1%,相对标准偏差小于5.1%,方法的检出限为0.083μg/L(S/N=3),定量限为0.25μg/L(S/N=10)。该方法简化了前处理过程,结合了MOF和水凝胶这二者各自的优点,添加的MOF材料可以在水凝胶体系中发挥其良好的吸附性,既解决了传统的MOF材料因粒径太小而回收率低的难题,便于吸附后直接提取,同时也解决了纯水凝胶吸附效率较低的问题,整体上提高了吸附效率和可回收性。实际样品测试表明该新型水凝胶吸附材料可用于养殖水体中孔雀石绿的快速萃取和检测,在食品检测领域具有很大潜力。     

Rapid detection of malachite green in fish with a fluorescence probe of molecularly imprinted polymer

A fluorescent probe based on CdTe/CdS quantum dots coated with molecularly imprinted polymer shell was designed. The fluorescence emission of the probe was at 622?nm. The probe presented selective adsorption for malachite green and the adsorption caused fluorescence quenching due to fluorescence resonance energy transfer. A linear relationship ranging from 0.05 to 10?μmol·L^?1 between relative fluorescence quenching intensities and malachite green concentrations was obtained with a detection limit of 0.029?μmol·L^?1. The fluorescent probe was successfully applied to the determination of malachite green in fish with recoveries ranging from 93.3 to 107.7%.     

Plasma Treated Sepiolite: A New Adsorbent for Removal of Malachite Green from Contaminated Water

Surface modification of clay materials has become an important issue to improve the efficiency of the adsorbent. The adsorption capacity of the clay material can be increased by thermal or chemical modifications. In this study, plasma technology was applied for the surface modification of sepiolite to improve the removal of malachite green from contaminated water. This study is novel in preparing and examining the effectiveness of sepiolite in adsorption of malachite green from contaminated water. To achieve the aim, plasma application time, CO₂, N₂, or Ar plasma gases effect and pH were investigated with respect to the adsorption capacity of MG. The surface properties of raw and plasma treated sepiolite were investigated with SEM, FTIR, BET surface area and XRD measurements. The monolayer adsorption capacity was found to be 143 mg/g.     

Removal of malachite green from dye wastewater using mesoporous carbon adsorbent

Mesoporous carbon was synthesized for the removal of a cationic dye malachite green (MG) from aqueous solution. The studies were carried out under various experimental conditions such as contact time, dye concentration, adsorption dose and pH to assess the potentiality of mesoporous carbon for the removal of malachite green dye from wastewater. The sorption equilibrium was reached within 30 min. In order to determine the adsorption capacity, the sorption data were analyzed using linear form of Langmuir and Freundlich equation. Langmuir equation showed higher conformity than Freundlich equation. More than 99% removal of MG was reached at the optimum pH value of 8.5. From kinetic experiments, it was concluded that the sorption process followed the pseudo-first-order kinetic model. This study showed that mesoporous carbon can be recommended as an excellent adsorbent at high pH values.     

活性炭的改性研究及对四环素的吸附

研究了改性对活性炭的物理化学性质及其对四环素吸附性能的影响。结果发现,硝酸氧化改性可增加活性炭表面的酸性基团,提高比表面亲水性,降低pHPZC值,同时也改变了活性炭的表面微观形貌。低温、低浓度硝酸氧化改性,增加了活性炭的比表面积,对四环素的吸附以物理吸附为主。高温氧化改性使得比表面积降低,酸性基团增加,且吸附容量与活性炭比表面积、表面总酸度呈一定的线性关系。     

Binary malachite green aptamer for fluorescent detection of nucleic acids

A new probe that can fluorescently report the presence of specific nucleic acids in solution with extremely high selectivity was developed. The probe consists of malachite green-a triphenylmethane dye-and two short RNA strands, each of which comprises a fragment complementary to an analyte molecule and a fragment of a malachite green aptamer (MGA). The two RNA strands form MGA upon hybridization to the adjacent positions of the nucleic acid analyte. MGA is able to bind malachite green and enhance the fluorescence of the dye, thus monitoring the presence of the nucleic acid in solution. The probe reliably discriminates against 41 out of 42 possible single nucleotide substitutions in 14-mer DNA analyte at room temperature in physiological buffer. Consisting of unmodified RNA strands, which can be expressed in living cells, binary MGA probe represents a promising instrument for real-time nucleic acid monitoring in vivo.