含10mol%氧化硅的钙磷酸盐玻璃陶瓷的合成及其体外生物活性

采用高分子网络凝胶法合成出SiO2-CaO-P2O5生物玻璃陶瓷,该材料具有较低含硅量和高钙磷比(nCa/nP=1.57)的特点,更接近人体硬组织的成分。将材料在SBF溶液浸泡研究材料的体外生物活性,通过TG/DTA,XRD,FTIR和SEM等方法对粉体和浸泡后的样品表面进行表征,ICP-AES对SBF溶液中钙、磷、硅离子的浓度进行检测。结果表明,氧化硅的添加有利于玻璃陶瓷表面磷灰石晶相的形成;随着浸泡时间的延长,沉积在样品表面的碳酸羟基磷灰石层逐渐由球型突起变为叶片状,溶液中钙、磷离子浓度降低,而硅离子浓度增加,说明材料具有良好的生物活性,适宜作为牙齿和骨骼的替代或修复材料。     

Development of a New Alkali Resistant Coating

The effect of different new sol-gel BaO—TiO₂—SiO₂ and CaO—BaO—TiO₂—SiO₂ coatings on long-term durability of glass fiber reinforced cement (GRC) was examined. Flexural strength of GRC was measured after curing for 7 to 150 days. Significant improvement was observed for coated GRC in this study and discussed in terms of the hydrate formation at interface. Concerned with the alkali resistance, CaO—BaO—TiO₂—SiO₂ coating was more effective than BaO—TiO₂—SiO₂ coating. In special, the 10CaO—10BaO—60TiO₂—20SiO₂ coating, prepared by sol-gel method, was recommended for the highest flexural strength of GRC and least corrosion at surface of E-glass fiber.     

A comparative study of the in vitro degradation of poly(l-lactic acid)/β-tricalcium phosphate scaffold in static and dynamic simulated body fluid

Porous poly(l-lactic acid)/β-tricalcium phosphate (PLLA/β-TCP) composite is a new promising scaffold for bone tissue engineering. Porous scaffolds fabricated by liquid anti-solvent precipitation principle were subjected to degradation in dynamic simulated body fluid (DSBF) and in static simulated body fluid (SSBF) at 37 °C for 24 weeks, respectively. Results indicated that a large number of apatite layer were formed on the scaffolds. The results further indicated that SBF flow decreased the degradation rate of molecular weight and compressive strength significantly. The porosity and mass changes were related to the apatite formation and SBF flow. All the results might be owed to the mutual effects of the flow of SBF and the addition of β-TCP. The degradation rate of scaffolds could be adjusted by the additional fraction of β-TCP to meet the requirements of application in vivo.     

Influence Of Zro2 on The Physicochemical Properties of Phosphate-Based Glasses and Glass Ceramics

Abstract

Phosphate-based bioactive glasses and their glass ceramics for 47P₂O₅– (30.5)CaO–(22.5 ? x)Na₂O–xZrO₂ for different ZrO₂ contents (x = 0, 1.5, 3.0, 4.5, and 6.0 mol%) were prepared through melt quenching and controlled heat treatment procedures. The amorphous nature of glasses and the presence of crystalline phases in glass ceramics were studied by means of X-ray diffraction (XRD) studies. The density, molar volume, ultrasonic velocities, attenuation, elastic constants, and microhardness of glass and glass ceramics were used to study the structural changes. The formation of hydroxyapatite layer on the surface of glasses and glass ceramics after immersion in simulated body fluid (SBF) was explored through XRD, Fourier transform infrared (FTIR), and scanning electron microscopy (SEM) analyses. The results indicate that the added ZrO₂ increases the crosslink density of glasses, resulting in network stability, and also induces the formation of an apatite layer on the surface of glasses.

Supplemental materials are available for this article. Go to the publisher's online edition of Phosphorus, Sulfur, and Silicon and the Related Elements to view the free supplemental file.     

Low-Density Forsterite (Mg2SiO4) Powders Prepared from Modified Alkoxides

2MgO-SiO₂ low-density powders have been prepared from alkoxide precursors modified with acetic anhydride. The resultant solutions did not gel, but formed precipitates. These consisted of an organic magnesium compound and amorphous silica. Tapping densities comparable with those of forsterite aerogels were obtained, with the density increasing as the precursor solution concentration increased. Crystalline forsterite formed around 790°C. Higher initial solution concentrations led to greater amounts of MgO in the powders after heating to 1000°C. Transmission electron microscopy showed primary particles between 20 and 30 nm which formed loose fractal agglomerates. By altering the preparation conditions, powders with morphologies more like aerogels than xerogels could be produced.     

Induction and Acceleration of Bonelike Apatite Formation on Tantalum Oxide Gel in Simulated Body Fluid

Untreated tantalum metal forms bonelike apatite layer on its surface in a simulated body fluid (SBF) after a long period. The apatite formation on the tantalum metal is significantly accelerated, when the metal was previously subjected to NaOH and heat treatments to form an amorphous sodium tantalate on its surface. The fast formation of the apatite on the NaOH- and heat-treated tantalum metal was explained as follows. The sodium tantalate on the surface of the metal releases the Na⁺ ion via exchange with H₃O⁺ ion in SBF to form a lot of Ta-OH groups on its surface. Thus formed Ta-OH groups induce the apatite nucleation and the released Na⁺ ion accelerates the apatite nucleation by increasing ionic activity product of the apatite in SBF due to increase in OH^– ion concentration. In the present study, in order to confirm this explanation, apatite formations on sodium tantalate gels with different Na/Ta atomic ratios, which were prepared by a sol-gel method were investigated. It was found that even Na₂O-free tantalum oxide gel forms the apatite on its surface in SBF. This proves that the Ta-OH groups abundant on the gel can induce the apatite nucleation. The apatite-forming ability of the gels increased with increasing Na/Ta atomic ratios of the gels. The sodium-containing tantalum oxide gels released the Na⁺ ion, the amount of which increased with increasing Na/Ta atomic ratios of the gels. The released Na⁺ ion gave an increase in pH of SBF. These results prove that the apatite nucleation induced by the Ta-OH groups is accelerated with the released Na⁺ ion by increasing ionic activity product of the apatite in SBF.     

Application of response surface methodology for optimization of the stability of asphaltene particles in crude oil by TiO2/SiO2 nanofluids under static and dynamic conditions

In this work, the onset of asphaltene flocculation for an Iranian crude oil by titration of samples with heptane in the presence and absence of the TiO₂/SiO₂ nanofluids was obtained by Near-IR spectroscopy. Nanoparticles and nanocomposites were characterized by BET, FESEM, EDX, XRD, and XRF analysis. Modeling and optimization of inhibition of asphaltene flocculation process by TiO₂/SiO₂ nanofluids were conducted by response surface methodology (RSM). Under optimum conditions (nanocomposite composition = 0.04 wt% (80%TiO₂:20%SiO₂), salinity = 4.01 wt%, and pH = 3.42), the onset point increased. For nanofluids stability analysis, the optimum nanofluid was compared with the two other nanofluids (SiO₂ and TiO₂) by visual observation method. The results indicated that high stability and surface area of the 80%TiO₂ nanocomposites increase asphaltene adsorption on the particles surface that subsequently increases the onset point. In addition, the optimum nanofluid performance on the carbonate rocks was evaluated by contact angle and core flooding experiments. The 80% TiO₂ nanofluid changed the wettability of carbonate rocks from strongly oil-wet to strongly water-wet condition and also decreased the residual oil saturation and enhanced the oil recovery with an increase in the recovery factor of about 15%.     

Sol-Gel Derived TiO2-SiO2 Fibres

TiO₂−SiO₂ fibres with 0, 5, 10 and 20 volume % SiO₂ have been prepared by drawing from a gel followed by sintering at different temperatures. Nearly one meter long fibres can be drawn easily in conditions of about 50% relative humidity. Addition of SiO₂ inhibits the crystallisation of TiO₂ and also the anatase → rutile transformation and improves the strength of the fibres. While the pure TiO₂ fibres are brittle, those with 5, 10 and 20 volume % SiO₂ are flexible and strong. Tensile strength values as high as 3 GPa have been achieved in the 10 volume % SiO₂−TiO₂ fibres. Fibres heated above 900°C are brittle. The shape of the cross section of the fibres is found to depend on their diameters.     

Calcination of SiO2-Aerogel in Inert Atmosphere

Thermal treatment of SiO₂-aerogel in inert atmosphere, in contrary to oxidizing atmosphere, yields a series of gas products with great range of mole masses (12–154 g mol^–1) and every product has specific way of evolving. These substances are represented by CO, CO₂, CH₄, CH₃OH, C₂H₆, C₂H₄ and aromates. Part of evolving products, which are formed during catalytic condensation, is trapped under the surface and after carbonisation it causes opacity of surface layer of aerogel.This revised version was published online in November 2005 with corrections to the Cover Date.     

Preparation and characterization of CuO/SiO2 and NiO/SiO2 with bimodal pore structure by sol-gel method

CuO/SiO₂ and NiO/SiO₂ with bimodal pore structure were prepared by sol-gel reactions of Tetra-methoxysilane (TMOS) and the respective metal nitrate in the presence of poly (ethylene oxide) (PEO) with an average molecular weight of 10 000 and the catalyst of acetic acid. In this process, the interconnected macroporous morphology was formed when transitional structures of spinodal decomposition were frozen by the sol-gel transition of silica. The addition of copper and nickel into the silica-PEO system had a negligible effect on the morphology formation. In gel formation, it was found that NiO crystalline sizes in the samples increased with decreasing Si/Ni molar ratio. It was considered that PEO interacted with both silica and nickel cations. In the CuO/SiO₂ with the presence of PEO_, CuO crystalline sizes were larger than those of NiO/SiO_2. It was considered that there was no obvious interaction between the Cu cation and PEO, most of the copper ions in wet silica gel were present in the outer solution. They easily aggregated as copper salts in the drying process of wet gel and decomposed into CuO particles in heating. While in the CuO/SiO₂ with the absence of PEO, the Cu was selectively entrapped as small particles in the gel skeleton due to the interaction between Cu aqua complex and silica gel network.     

Synthesis of Ag/SiO2 nanocomposite material by adsorption phase nanoreactor technique

Ag/SiO₂ nanocomposite was synthesized in a nanoreactor formed by adsorption layer on silica surface. Ag nanoparticles were prepared by the reduction of Ag ion with ethanol at alkaline condition. By using TEM and XRD, the effects of NaOH concentration, water and temperature on the appearance and grain size of Ag particles were analyzed, respectively. The adsorption curve of NaOH was measured by electrical conductivity meter. The experiment result revealed that Ag grain size decreased while increasing NaOH concentration or while increasing water in our system. Ag grain size increased with the increase of temperature. And Ag aggregated seriously when temperature is up to 60 °C. Finally, after exploring the optimum conditions of reaction, we successfully obtained the well-distributed Ag nanoparticles on surface of silica, and average grain size of Ag nanoparticles reached 5 nm.     

Formation of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript> bilayer using atomic layer deposition and its application to dynamic random access memory

To enhance film conformality together with electrical property suitable for dynamic random access memory (DRAM) capacitor dielectric, the effects of oxidant and post heat treatment were investigated on aluminum and titanium oxide (Al₂O₃–TiO₂) bilayer (ATO) thin film formed by atomic layer deposition method. For the conformal deposition of Al₂O₃ thin film, the O₃ oxidant required a higher deposition temperature, more than 450 °C, while H₂O or combined oxygen sources (H₂O+O₃) needed a wide range of deposition temperatures ranging from 250 to 450 °C. Conformal deposition of the TiO₂ thin film was achieved at around 325 °C regardless of the oxidants. The charge storage capacitance, measured from the ATO bilayer (4 nm Al₂O₃ and 2 nm TiO₂) deposited at 450 °C for Al₂O₃ and 325 °C for TiO₂ with O₃ oxidant on the phosphine-doped poly silicon trench, showed about 15% higher value than that of 5 nm Al₂O₃ single layer thin film without any increase of leakage current. To maintain the improved electrical property of the ATO bilayer for DRAM application, such as enhanced charge capacitance without increase of leakage current, upper electrode materials and post heat treatments after electrode formation must be selected carefully. Dedicated to Professor Su-Il Pyun on the occasion of his 65th birthday.     

Gas Liquid Chromatographic—Mass Spectrometric Methods for Quantitation of Prostaglandin Analogs

Abstract

The synthesis of tetradeuterated 15-methyl-PGF_2α and 17-phenyl-18, 19, 20-trinor-PGF_2α, is described. Gas chromatographic -mass spectrometric methods, using the deuterated compounds as internal standards and carriers, for quantitation of corresponding unlabeled prostaglandin analogues is described. With acceptable accuracy and precision the sensitivity is in the subpicomole range.     

Investigation of RuO2-IrO2-SnO2 thin film evolution

The thermal evolution process of RuO₂–IrO₂–SnO₂ mixed oxide thin films of varying noble metal contents has been investigated under in situ conditions by thermogravimetry-mass spectrometry (TG-MS), infrared emission spectroscopy (IR) and cyclic voltammetry (CV). The gel-like films prepared from aqueous solutions of the precursor compounds RuOHCl₃, H₂IrCl₆ and Sn(OH)₂(CH₃COO)_2–xCl_x on titanium metal support were heated in an atmosphere containing 20% O₂ and 80% Ar up to 600°C. Chlorine evolution takes place in a single step between 320 and 500°C accompanied with the decomposition of the acetate ligand. The decomposition of surface species formed like carbonyls, carboxylates and carbonates occurs in two stages between 200 and 500°C. The temperature of chlorine evolution and that of the final film formation increases with the increase of the iridium content in the films. The anodic peak charge shows a maximum value at 18% iridium content.     

The role of precursors in the structure of SiO2-Al2O3 sols and gels by the sol-gel process

Binary sols and gels of SiO₂-Al₂O₃ were prepared using tetraethyl orthosilicate and each of four aluminum compounds; aluminum di (sec-butoxide) ethylacetoacetic ester chelate (AC), aluminum nitrate nonahydrate (AN), aluminum formoacetate (AF), and boehmite sol (BS) made from aluminum i-propoxide. The structure and the evolution of the Si-O-Al bonds in SiO₂-Al₂O₃ sols and gels were investigated by ²⁷Al nuclear magnetic resonance (NMR), Infrared absorption spectra, DTA, and X-ray diffraction. The formation of Si-O-Al bonds differs depending on the aluminum compounds used as raw materials. The ratio of Al(IV) to {Al(IV) + Al(VI)} is related to the microstructural homogeneity of the gels. When AC is used as a raw material, the Si-O-Al bonds are formed in the sol state and resultant gel shows good microstructural homogeneity. In case of AN, the Si-O-Al bonds are not formed either in the sol or the wet gel state. The bonds are formed by drying the gel before heat-treatment temperature reaches 300 400°C, resulting in good microstructural homogeneous gel. When AF is used, the Si-O-Al bonds are formed in the sol state but the ratio of Al(IV) to {Al(IV) + Al(VI)} is lower than when using AC. Microstructural homogeneity of the gel is ranked between AC or AN and BS. Using BS, the Si-O-Al bonds are not formed in the sol solution, and the change in the coordination number of the gel is similar to that of boehmite gel. The Microstructural homogeneity of the gel is the worst among the BS gels, which were prepared by using the four aluminum raw materials.     

Sol–Gel SiO2-ZrO2 Coatings for Optical Applications

SiO₂-ZrO₂ based nanostructured multilayers films have been prepared by sol–gel processing from metallorganic precursors by low temperature inorganic polymerization reactions. Simultaneous gelation of both precursors was realized. Homogeneous and transparent films were obtained at room temperature by dip- and spin-coating on glass and silicon wafer substrates. Samples with successively deposited layers (1–3 layers) and successive thermal treatments have been also studied. Each deposited layer was thermally treated for 1 h at 300°C. The coatings were characterized by XRD, spectroellipsometry (SE), UV-VIS spectroscopy and AFM methods. The influence of substrates, number of coatings and number of thermal treatments on the optical and structural properties of the films was established. The thickness of three deposited SiO₂-ZrO₂ layers is about 496 nm on glass substrates and 413 nm on the silicon wafer substrate. The films deposited on glass are more porous than those deposited on silicon. The properties of optical waveguide prepared from SiO₂-ZrO₂ layers on silicon substrates will be discussed.     

Simultaneous thermoanalytical investigations of (C6H5)4AsCl and (C6H5)4PCl under air and argon atmospheres

The thermoanalytical curves of (C₆H₅)₄AsCl (I) and (C₆H₅)₄PCl (II) were generated simultaneously by using a Netzsch simultaneous thermal analyser 409 under static air and dynamic argon atmospheres. The ranges of thermal stability of I and II were found to be 145–310°C and 137–365°C, respectively, and their melting points to be 261 and 278°C. The DTA profiles of I and II differ and can be used for their distinction.     

Capacitance and photocurrent study of electronic properties of anodic oxide films on Nb and Ta. Evaluation of the ionized donor concentration profile in Nb2O5 film

Electronic properties of electrochemically formed oxide films on Nb were studied by photocurrent and differential capacitance measurements in 0.025 M KH₂PO₄+0.025 M Na₂HPO₄ electrolyte, pH 6.9. Oxide films of n-type conductivity were formed galvanostatically for final potentials ranging from 4 to 230 V. Measurements were performed in two potential regions, which correspond to formation of a depleted layer of variable thickness at relatively low potentials, and to complete depletion of oxide films of electronic charge carriers at higher potentials. In the first potential region the behavior of both capacitance and photocurrent, was governed by a build up of a depleted layer of potential dependent thickness. In the second, high potential, region, which extends up to the oxide film formation potential, the photocurrent and capacitance of oxide films in most features followed the trends typical of dielectric films containing defects and traps. The photocurrent and capacitance measurements on presumably dielectric oxide films formed on Ta were staged for comparison. The capacitance–potential measurements performed in the first potential region enabled us to construct the ionized donor concentration profile across the Nb₂O₅ film width. The limitations on the use of the C–E profiling method for electrochemically formed oxide layers are considered.     

Synthesis of nanosized TiO2/SiO2 particles using microwave processes and their photocatalytic activity on the decomposition of orange II

The nanosized titania and TiO₂/SiO₂ particles were prepared by the microwave-hydrothermal method. The effect of physical properties TTIP/TEOS ratio and calcination temperature has been investigated. The major phase of the pure TiO₂ particle is of the anatase structure, and a rutile peak was observed above 800°C. In TiO₂/SiO₂ particles, however, no significant rutile phase was observed, although the calcination temperature was 900°C. No peaks for the silica crystal phase were observed at either silica/titania ratio. The crystallite size of TiO₂/SiO₂ particles decreases as compared to pure TiO₂ at high calcination temperatures. The TiO₂/SiO₂ particles show higher activity on the photocatalytic decomposition of orange II as compared to pure TiO₂ particles.     

High Temperature Reactions in the MoO3-Ag2O System

High-temperature reactions were investigated in the MoO₃-Ag₂O system by means of X-ray, DTA and scanning microscopy methods, and a model was proposed according to which first an Ag₂Mo₄O₁₃ phase was formed at the MoO₃ and Ag₂O (or metallic Ag) interface. Subsequently, at the Ag₂Mo₄O₁₃-Ag₂O contact area a layer of Ag₂Mo₂O₇ appeared. If the amount of silver oxide is sufficiently high, a layer of Ag₂MoO₄ is formed between the Ag₂O and Ag₂Mo₂O₇ phases. This revised version was published online in July 2006 with corrections to the Cover Date.