对称抛物势阱磁性隧道结中的自旋输运及磁电阻效应

研究了两端具有铁磁接触的对称抛物势阱磁性隧道结(F/SPW/F)中自旋相关的隧穿概率和隧穿磁电阻,讨论了量子尺寸效应和Rashba 自旋轨道耦合作用对自旋极化输运特性的影响.研究结果表明:隧穿概率和隧穿磁电阻随抛物势阱宽度的增加发生周期性的振荡.抛物势阱深度的增加减小了隧穿概率和隧穿磁电阻的振荡频率.Rashba 自旋轨道耦合强度的增加加大了隧穿概率和隧穿磁电阻的振荡频率.隧穿概率和隧穿磁电阻的振幅和峰谷比强烈依赖于两铁磁电极中磁化方向的夹角. 关键词： 磁性隧道结 Rashba 自旋轨道耦合 隧穿概率 隧穿磁电阻     

磁性隧道结自旋极化电子的隧穿特性

铁磁金属间通过中间层的自旋极化电子隧穿产生的磁性耦合,在自旋电子器件中有许多潜在的应用.考虑由一平面磁性势垒层隔开的两铁磁性金属电极构成的磁性隧道结,针对中间层形成的矩形势垒,在近自由电子模型的基础上,计算零偏压下的隧穿电导、自旋极化率和隧穿磁阻比率,分析势垒层特性、分子场强弱、分子场相对取向等对隧道结自旋极化电子隧穿特性的影响.计算结果对自旋电子器件的设计具有一定的指导意义.     

磁性隧道结电子输运特性的研究

在Slonczewsik自由电子理论模型下,研究了两铁磁性金属电极被一平面磁性势垒隔开的磁性隧道结零偏压下的隧穿电导、自旋极化率和隧穿磁阻比率,研究表明隧道结的磁结构对隧穿电导和隧穿磁阻的值有很大的影响,当两磁性电极分子场方向相同,且都与势垒层分子场反平行时,隧穿电导数值达到最大,两者平行时,其数值最小,同时还分析了分子场的相对取向等对磁性隧道结自旋极化电子输运性质的影响.研究结果对自旋电子器件的设计具有一定的指导意义.     

磁性隧道结电子输运特性的研究

在Slonczewsik自由电子理论模型下,研究了两铁磁性金属电极被一平面磁性势垒隔开的磁性隧道结零偏压下的隧穿电导、自旋极化率和隧穿磁阻比率,研究表明隧道结的磁结构对隧穿电导和隧穿磁阻的值有很大的影响,当两磁性电极分子场方向相同,且都与势垒层分子场反平行时,隧穿电导数值达到最大,两者平行时,其数值最小,同时还分析了分子场的相对取向等对磁性隧道结自旋极化电子输运性质的影响。研究结果对自旋电子器件的设计具有一定的指导意义。     

双势垒磁性隧道结的磁电阻效应及其在自旋晶体管中的应用

利用磁控溅射方法沉积双势垒磁性隧道结多层膜, 其中Al-O势垒层由等离子体氧化1 nm厚的 金属铝膜方式制备，然后采用深紫外光曝光和Ar离子刻蚀技术、微加工制备出长短轴分别为 6和3 μm大小的椭圆形双势垒磁性隧道结（DBMTJ），并在室温和低温下对其自旋电子输运 特性进行了研究. DBMTJ的隧穿磁电阻(TMR)比值在室温和42 K分别达到27％和423％， 结电阻分别为136 kΩ·μm²和175 kΩ·μm²，并在实验中观 察到平行状 态下存在低电阻态及共振隧穿效应，反平行态下呈现高电阻态以及TMR随外加偏压或直流电 流的增加而发生振荡现象. 由此，设计了一种基于这种双势垒磁性隧道结隧穿特性的自旋晶 体管. 关键词： 双势垒磁性隧道结 隧穿磁电阻 共振隧穿效应 自旋晶体管     

NM/FI/NI/FI/NM新型双自旋过滤隧道结的隧穿电导和隧穿磁电阻

在NM/FI/FI/NM型双自旋过滤隧道结(此处NM为非磁金属层，FI为铁磁绝缘体或半导体层)的基础上，我们提出一种NM/FI/NI/FI/NM新型双自旋过滤隧道结(此处NI表示非磁绝缘体或半导体层). 插入NI层的目的是为了避免原双自旋过滤隧道结中相邻FI层界面处磁的耦合作用所导致的对隧穿磁电阻的不利影响. 在自由电子近似的基础上，利用转移矩阵方法，对NM/FI/NI/FI/NM新型双自旋过滤隧道结的隧穿电导、隧穿磁电阻与FI层及NI层厚度的变化关系以及随偏压的变化关系进行了理论研究.计算结果表明，在NM/FI/NI/FI/NM新型双自旋过滤隧道结中仍可以得到很大的TMR值. 关键词： 双自旋过滤隧道结 隧穿磁电阻 非磁绝缘(半导)体间隔层     

铁磁/半导体/铁磁结构的双量子环自旋输运的特性

研究了与铁磁/半导体/铁磁结构相关的双量子环自旋输运的规律,研究结果表明：总磁通为零条件下,铁磁电极磁化方向反平行时,双量子环与单量子环相比提高了自旋电子透射概率的平均值.铁磁电极磁化方向平行时,双量子环对提高自旋向下电子平均透射概率的效果更明显;双量子环受到Rashba自旋轨道耦合作用影响时,自旋电子的平均透射概率明显高于单量子环,即使再加上外加磁场的影响,透射概率较高这一特征依然存在;双量子环所含的δ势垒具有阻碍自旋电子输运的作用,随δ势垒强度Z的增大透射概率 关键词： 双量子环 Rashba自旋轨道耦合 透射概率 δ势垒')" href="#">δ势垒     

第五讲 自旋极化输运及隧道巨磁电阻效应

简要回顾了利用量子隧道效应测定铁磁金属传导电子自旋极化率的研究历史，综述了自旋极化电子隧穿产应导致的“铁磁金属／非磁绝缘体／铁磁金属”三层平面型隧道结中的巨磁电阻效应以及“铁磁金属／非磁绝缘体”颗粒膜系统中的隧穿类型巨磁电阻效应的研究进展。     

处理具有任意形状势垒的磁性隧道结中电子输运的一个简单方法

在Slonczewski自由电子模型的基础上,提出了一个可用于处理具有任意形状势垒的磁性隧道结中磁电子输运的简单方法,并以三种常见构形的势垒,即梯形势垒,计入了镜像势的梯形势垒和抛物线势垒为例,讨论了势垒形状对隧穿磁电阻及其随偏压变化的影响. 关键词： 磁性隧道结 隧穿磁电阻 任意形状势垒 非零偏压     

磁量子结构中二维自旋电子的隧穿输运

研究了零偏压和偏置电压作用下磁量子结构中自旋电子的隧穿输运性质. 结果表明电子自旋 输运的性质不仅取决于磁量子结构的构型、入射电子的能量和波矢, 而且取决于偏置电压. 在零偏压下, 由等同的磁垒磁阱构成的磁量子结构不具有自旋过滤的特点, 而由不等同的磁 垒磁阱构成的磁量子结构却具有较好的自旋过滤特点. 偏置电压极大地改变了磁量子结构中 电子的极化程度, 使得电子隧穿等同的磁垒磁阱构成的磁量子结构的输运性质也显著地依赖 于电子的自旋指向. 关键词： 磁量子结构 自旋电子 隧穿输运 自旋极化     

Tunneling magnetoresistance of the double spin-filter junctions at nonzero bias

A recent theoretical estimation indicated that the NM/FI/FI/NM double spin-filter junction (DSFJ, here the NM and FI represent the nonmagnetic electrode and the ferromagnetic insulator (semiconductor) spacer, respectively) could have very high tunneling magnetoresistance (TMR) at zero bias. To meet the requirement in research and application of the magnetoresistance devices, we have calculated the dependences of tunneling magnetoresistance of DSFJ on the bias (voltage), the thicknesses of ferromagnetic insulators (semiconductors) and the average barrier height. Our results show that except its very high value, the TMR of DSFJ does not decrease monotonously and rapidly with rising bias, but increase slowly at first and decrease then after having reached a maximum value. This feature is in distinct contrast to the ordinary magnetic tunnel junction FM/NI/FM (FM and NI denote the ferromagnetic electrode and the nonmagnetic insulator (semiconductor) spacer, respectively), and is of benefit to the use of DSFJ as a magnetoresistance device.     

自旋轨道耦合作用下石墨烯pn结的电子输运性质

本文研究了自旋轨道耦合作用下石墨烯纳米带pn结的电子输运性质. 当粒子的入射能量处于pn结两端势能之间时, 粒子将会以隧穿的形式通过石墨烯pn结, 同时伴随着电子空穴转换. 电导随费米能的变化曲线呈不等高阶梯状, 并在费米能位于pn结两端能量中点时取得最大值. 随着石墨烯pn结长度的增加, 电导以指数形式衰减. 自旋轨道耦合作用导致的能隙会使电导显著减小, 而边缘态的粒子则可以几乎毫无阻碍地通过pn结. 本文用一个简单的子带隧穿模型解释了上述特征. 最后还研究了在pn转换区中掺入替位杂质的情况. 在弱杂质下, 电导随费米能变化的曲线将不再对称; 当杂质较强时, 仅边界态的形成的电导台阶能够保持.     

Observation of single-spin transport in an island-shaped CoFeB double magnetic tunnel junction prepared by magnetron sputtering

The Co₄₀Fe₄₀B₂₀(CFB)/MgO/CFB/MgO/CFB-based multilayer was prepared by conventional magnetron sputtering and utilised in the fabrication of double magnetic tunnel junctions (DMTJs) for which the middle CFB layers were island-shaped. By analysing the magnetic property of the CFB islands with Langevin’s equation, it was possible to identify their diameters of 7.6, 8.9 and 11.0 nm; accordingly submicron-scaled DMTJs were fabricated to investigate single-spin transport phenomena. The coulomb staircase and the oscillatory tunnel magnetoresistive (TMR) were able to be observed at 6 K, where the TMR ratio was enhanced up to 60%, which is the highest value ever achieved in this structure.     

Magnetoresistance in silicon based ferrite magnetic tunnel junction

We report magnetoresistance for silicon based magnetic tunnel junction. We used cobalt ferrite & cobalt nickel ferrite as free layer and pinned layer. The magnetoresistance measured at room temperature through silicon by fabricating FM/Si/FM magnetic tunnel junction. Magnetoresistance shows a loop type behavior with 3.7%. We have successfully demonstrated spin tunneling through silicon with ferrite junction that opens the door for potential candidate for spintronics devices. The spin-filtering effect for this double spin-filter junction is also discussed.     

Electronic double refraction due to the Rashba effect: Analytical and numerical results

By analogy with the classic effect of the double refraction of light, we investigate the relevant effect of an electron entering from the Non-Rashba region to the Rashba region in two-dimensional systems. It is shown that the effect of electronic double refraction is determined by a combined parameter γ = m ^* λ _F α/2πħ², rather than both the Rashba coefficient α and wavelength λ _F of a Fermi electron, separately. For the case of normal incidence, the analytical expressions for the wavefunction of the electron are presented; it is predicted that the Rashba spin-orbit coupling can induce a current perpendicular to the normal incident direction of the electron. Moreover, the general case of incident electron with any given momentum and spin state are studied numerically in detail, including the abrupt changes of spin direction and the two-step characters for reflection.      

Crystallization characteristics of a middle CoFeB layer in a double MgO barrier magnetic tunnel junction

The crystallization characteristics of a middle CoFeB free layer in a magnetic tunnel junction (MTJ) with double MgO barriers were investigated by tunneling magnetoresistance (TMR) measurements of patterned cells across an 8-inch wafer. The MTJ structure was designed to have two CoFeB free layers and one bottom pinned layer, separated by MgO tunnel barriers. The observed resistance showed three types of TMR curves depending on the crystallization of the middle CoFeB layer. From the analysis of TMR curves, coherent crystallization of the middle CoFeB layer with the top and bottom MgO barriers was found to occur non-uniformly: About 80% of the MTJ cells in the wafer exhibited coherent crystallization of the middle CoFeB layers with the bottom MgO tunnel barrier, while others had coherent crystallization with the top MgO tunnel barrier or both barriers. This non-uniform crystallization of the middle CoFeB layer in a double MTJ was also clearly observed in tunneling electron microscopy images. Thus, control of the crystallization of the middle CoFeB layer is important for optimizing the MTJ with double MgO barriers, and especially for the fabrication of double barrier MTJ on a large area substrate.     

超导隧道结中的电流相位关系

计算了等自旋配对超导隧道结中的直流Josephson电流.结果表明,当两侧超导体中配对势的轨道对称性分别属于磁点群D₄的A不可约表示和 ²E不可约表示的情况下,电流相位关系是I∝sin4φ. 关键词： 超导隧道结 Josephson电流     

Multiferroic tunnel junctions

Magnetic tunnel junctions with ferroelectric barriers, often referred to as multiferroic tunnel junctions, have been proposed recently to display new functionalities and new device concepts. One of the notable predictions is that the combination of two charge polarizing states and the parallel and antiparallel magnetic states could make it a four resistance state device. We have recently studied the ferroelectric tunneling using a scanning probe technique and multiferroic tunnel junctions using ferromagnetic La_0.7Ca_0.3MnO₃ and La_0.7Sr_0.3MnO₃ as the electrodes and ferroelectric (Ba, Sr)TiO₃ as the barrier in trilayer planner junctions. We show that very thin (Ba, Sr)TiO₃ films can sustain ferroelectricity up till room temperature. The multiferroic tunnel junctions show four resistance states as predicted and can operate at room temperatures.