微波照射制备钛酸钡纳米晶

Cubic barium titanate nanocrystals were prepared by Ti(OC₄H₉)₄ and C₂H₅OH mixture with BaCl₂ aqueous solution under normal atmosphere microwave irradiation. Experiment results showed that when n_Ba / n_Ti=1.1, φ_EtOH=25%,highly dispersed barium titanate with particle size about 30 nm were completely formed by microwave irradiation only for 0.5 h. Microwave irradiation time had almost no effects on particle size and morphology of the product. Particle sizes were decreased with the increased EtOH amount, when φ_EtOH=50%, microwave irradiation 2 h, barium titanate nanocrystals with average size only about 22 nm were obtained.     

纳米钛酸钡及其烧结物的制备

溶胶 凝胶技术已为制备各种金属氧化物纳米材料的较普遍方法[1],其优点是产物具有超细颗粒尺寸 ,高纯度和化学均匀性 .溶胶 凝胶法制备纳米钛酸钡时一般将钛的有机醇盐与钡盐反应生成溶胶 ,然后形成凝胶 ,再进行热处理制得纳米钛酸钡[2 ,3].本文以钛酸丁酯和氢氧化钡为原料 ,采用溶胶 凝胶工艺制备出纳米钛酸钡晶体粉末 .用ＴＧ ＤＴＡ和ＦＴＩＲ技术考查了纳米晶钛酸钡凝胶先体热分解反应过程 ,用ＳＥＭ和ＸＲＤ对粉体形貌和晶型进行分析 ;并用上述粉体制成了微观组织结构仍保持纳米尺寸的陶瓷材料 .粉体制备 :称 15 7ｇ氢氧化钡 (Ｂａ(…     

单分散钛酸钡纳米晶的制备

采用溶剂热法制备出表面包裹油酸的单分散立方相钛酸钡纳米晶, 晶粒平均尺寸为6.0 nm, 采用TEM和XRD对其微结构进行了表征; 研究了醇的链长度、油酸用量和热处理温度等对钛酸钡的相组成和形貌的影响规律. 研究结果表明, 产物粒径较小, 粒度分布较窄, 单分散性较好, 其表面为非极性, 可溶于非极性试剂; 由于纳米晶表面由亲油性的长链烷基所覆盖, 与周围的水性环境不相容, 产生一定的斥力; 在重力和该斥力的共同作用下, 纳米晶可以有效地从液相环境中分离出来.     

简捷水热前驱物技术制备钛酸钡纳米棒与纳米球

A facile synthesis route has been developed to prepare barium titanate nanoparitcles via a low temperature (120 ℃) hydrothermal decomposition of single-source metal-organic precursor. A mixture of tetramethylammonium hydroxide (TMAH) and distilled water was used as reaction media, and Barium titanium ethyl-hexano- isoproxide [BaTi(O₂CC₇H₁₅)(OC₃H₇)₅] was used as precursor. The architecture of products can be selectively controlled from nanorods to nanospheres by adjusting the precursor′s concentration in the reaction system. Powder X-ray diffraction (XRD) analysis indicated that the products were in cubic phase. Transmission electronic microscopy (TEM) observation showed that the nanospheres were 30～50 nm in diameter, and the nanorods were 5～10 nm in diameter and 100～600 nm in length, respectively. Phase transformation behavior of the as-prepared products was also investigated.     

聚苯胺/钛酸钡纳米复合粒子的制备与表征

采用原位复合法制备出聚苯胺/钛酸钡复合粒子,借助TEM、XRD、FT-IR、 XPS、TG等分析手段研究了复合粒子的形貌、结构及其热性能.结果表明,复合粒子的粒径为1 μm左右,BaTiO3以40 nm左右的晶粒分散于聚苯胺基体之中,聚苯胺与钛酸钡之间存在化学键合作用,同时在一定程度上减少了纳米粒子的团聚.     

纳米晶钛酸钡的介电性能

采用硬脂酸凝胶法制备了纳米晶BaTiO3,用差热热重分析、红外光谱分析、X射线衍射分析等手段对产物的形成过程、晶型、粒径进行了分析.通过对材料介电性能的研究发现,纳米材料的静态介电常数远大于常规材料的介电常数,随着粒径的减小,纳米材料的介电常数先增大而后有所降低.随着环境湿度的升高,纳米晶材料的介电常数逐渐增大,在高湿度条件下,其介电常数与湿度成线性关系.     

纳米钛酸钡的水热合成进展

综述了水热合成纳米钛酸钡的影响因素、发展现状及存在的问题，并指出其发展趋势。参考文献57篇。     

纳米钛酸钡生成的热分解机理

钛酸钡作为重要的铁电材料 ,多年来一直被研究者们所关注．传统方法制备钛酸钡大多采用固相法或草酸盐法得到微米级基料．随着纳米材料研究与应用的发展 ,溶胶 凝胶技术成为制备各种金属氧化物纳米材料的较普遍方法．溶胶 凝胶法制备纳米钛酸钡就是其中之一．该法一般采用钛的有机醇盐与钡盐反应生成溶胶 ,然后形成凝胶 ,再以凝胶为先体进行热处理制得纳米钛酸钡．虽然已有人对溶胶 凝胶技术制备纳米钛酸钡进行了研究 ,并对所得产物进行了表征［１,２］,但尚无人对该方法中凝胶的热分解过程作详细的研究．因凝胶的热分解过程对钛酸钡纳…     

表面修饰的钛酸钡纳米粉体的制备

采用水热法制备出表面包裹有硬脂酸的钛酸钡纳米粉体,并运用一系列手段对其微结构进行了表征.结果表明:产物粒径较小,粒度分布较窄,单分散性较好,其表面为非极性,同时表现出良好的流动性能.认为钛酸钡纳米粉体表面极性的改变是由于其表面包裹了一层硬脂酸,并且包裹层降低了粉体间的相互作用力,从而提高了粉体的流动性.     

掺镁钛酸钡纳米棒的水热合成和光催化性能

用水热法制备掺镁钛酸钡(Ba1-xMgxTiO3(x=0,0.10,0.20,0.30,0.40),BMT)纳米粉体。运用X射线衍射仪(XRD)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、紫外可见漫反射光谱技术(DRS)等手段对样品进行了表征,并在可见光照射下于溶液中考察了其光催化降解甲基橙反应活性。结果表明,通过控制氢氧根浓度可以得到不同形貌的纳米粉体。基于不同条件下制备的样品的微结构分析,提出了这些不同形貌的形成机制。制备出的BMT材料的带隙能约为2.61 eV。光催化反应结果表明BMT的光催化活性比掺氮TiO2高得多。OH-浓度为8 mol·L-1时制备的BMT纳米棒光催化效率最高,经可见光照射360 min,浓度为0.01 mmol·L-1甲基橙溶液的降解率可达到93.0%,且循环使用4次后,其光催化活性并没有明显降低,表明BMT是一种稳定有效的可见光催化剂.     

四方相钛酸钡纳米枝晶阵列的水热合成

采用水热法,在表面活性剂十六烷基三甲基溴化铵(CTAB)和合适的矿化剂NaOH的作用下,得到具有新颖结构的钛酸钡纳米枝晶阵列。X射线衍射(XRD)和拉曼光谱(Raman)结果分析显示该枝晶为四方相,随着时间的延长其结晶性增强、四方相更加明显。利用扫描电子显微镜(SEM)、高分辨透射电子显微镜(HRTEM)和电子衍射(ED)研究了该枝晶的生长特点和生长机理,结果表明该枝晶其各枝均沿着[111]方向生长,并且同级枝相互平行形成阵列;在枝晶阵列的外侧部分会有2级子枝长出,中间部位由于空间阻碍没有子枝形成。同时探讨了CTAB和NaOH在枝晶形成过程中的作用机理,以及枝晶产品的介电性能。     

溶胶-凝胶模板法制备钛酸钡纳米管

采用氢氧化钡和钛酸四丁酯为前驱体, 溶胶-凝胶结合模板法制备了钛酸钡纳米管, 通过SEM, TEM, XPS和XRD等表征分析, 钛酸钡纳米管直径100 nm, 钛酸钡为立方相结构, 晶胞参数a＝3.995 Å.     

Ca改性钛酸铅纳米晶的制备及结构研究

用溶胶-凝胶工艺制备了Pb_1-xCa_xTiO₃(0≤x≤0.3)纳米晶,在不同焙烧条件下研究其粉体晶相结构的变化.研究结果表明,升温速度和焙烧温度对纳米粉的晶相、晶胞参数和晶粒尺寸有显著影响.讨论了晶胞参数、四方畸变度和晶胞体积与Ca含量的关系.     

Dispersibility of Barium Titanate Suspension in the Presence of Polyelectrolytes: A Review

Dispersibility of colloidal barium titanate suspensions is reviewed with an emphasis on the use of various polyelectrolytes as dispersants. The fundamentals of colloidal stability are discussed followed by the colloidal properties of barium titanate powder. Dispersion behavior of BaTiO₃ in both nonaqueous and aqueous media has been reviewed. Several studies on the stabilization of micron and nano‐sized barium titanate using various polymeric dispersants and a rhamnolipid biosurfactant are presented and discussed. The article attempts to provide a comprehensive review of the current state‐of‐the‐art in the area of colloidal processing of barium titanate.     

超细钛酸钡粉体的水热合成

以偏钛酸和氢氧化钡为原料,用水热反应制备了超细钛酸钡粉体,其结构经XRD和-IEM表征。粒径60nm-100nm。较佳的反应条件为：偏钛酸20mmol,n(Ba)：n(Ti)=1．2,于240℃反应8h,加入少量异丙醇可明显改善粉体的分散性能。     

溶胶-凝胶法制备掺锰钛酸钡纳米粉体及其陶瓷

The Mn-doped barium titanate nanosized powders and ceramics were prepared via the sol-gel process. The powders and ceramics were characterized by XRD， SEM and TEM. The dielectric properties of the ceramics were also measured. The influences of calcination temperature and Mn concentration on the microstructure， dielectric properties and phase composition of BaTiO₃ nano-powders and ceramics were discussed. The results indicated that the BaTiO₃-based powders doped with 1.0mol% Mn were mainly in cubic BaTiO₃ phase， but the tetragonal phase became more evident when the calcination temperature increased. After sintering， Mn-doped ceramics were mainly composed of cubic BaTiO₃. Specially， a new phase of hexagonal crystal BaTiO₃ and BaMnO₃ existed in the ceramics doped with 5.0mol% Mn and the ceramic grains were in ‘clintheriform’. The structure of ‘clintheriform’ led to the poor densification of ceramics， reducing the dielectric constant obviously. The dielectric constants of BaTiO₃ ceramics first increased and then decreased as the Mn concentration increased. The room temperature dielectric constant was 2 290 and the lowest dielectric loss was 0.004 when the Mn concentration was 0.5mol%.     

Synthesis and Electrorheological Characterization of Polyaniline/Barium Titanate Hybrid Suspension

As organic/inorganic composites having attracted much attention due to their heterogeneous physical properties, conducting polyaniline (PANI) and barium titanate (BaTiO₃) which possesses large electronic resistance and excellent dielectric strength, were utilized to synthesize PANI/BaTiO₃ hybrid which is applicable for an electrorheological (ER) material via ‘in-situ’ oxidative polymerization. Physical properties of the obtained PANI/BaTiO₃ composites were characterized via Fourier-transform infrared spectra (FT-IR), thermogravimetry analysis (TGA), and scanning electron microscopy (SEM). The ER behaviors were investigated via a rotational rheometer, and their shear stresses were fitted using our previously proposed rheological equation of state.