SUT‐NANOTEC‐SLRI beamline for X‐ray absorption spectroscopy

The SUT‐NANOTEC‐SLRI beamline was constructed in 2012 as the flagship of the SUT‐NANOTEC‐SLRI Joint Research Facility for Synchrotron Utilization, co‐established by Suranaree University of Technology (SUT), National Nanotechnology Center (NANOTEC) and Synchrotron Light Research Institute (SLRI). It is an intermediate‐energy X‐ray absorption spectroscopy (XAS) beamline at SLRI. The beamline delivers an unfocused monochromatic X‐ray beam of tunable photon energy (1.25–10 keV). The maximum normal incident beam size is 13 mm (width) × 1 mm (height) with a photon flux of 3 × 10⁸ to 2 × 10¹⁰ photons s^?1 (100 mA)^?1 varying across photon energies. Details of the beamline and XAS instrumentation are described. To demonstrate the beamline performance, K‐edge XANES spectra of MgO, Al₂O₃, S₈, FeS, FeSO₄, Cu, Cu₂O and CuO, and EXAFS spectra of Cu and CuO are presented.     

Pressure study of monoclinic ReO2 up to 1.2 GPa using X‐ray absorption spectroscopy and X‐ray diffraction

The crystal and local atomic structure of monoclinic ReO₂ (α‐ReO₂) under hydrostatic pressure up to 1.2 GPa was investigated for the first time using both X‐ray absorption spectroscopy and high‐resolution synchrotron X‐ray powder diffraction and a home‐built B₄C anvil pressure cell developed for this purpose. Extended X‐ray absorption fine‐structure (EXAFS) data analysis at pressures from ambient up to 1.2 GPa indicates that there are two distinct Re—Re distances and a distorted ReO₆ octahedron in the α‐ReO₂ structure. X‐ray diffraction analysis at ambient pressure revealed an unambiguous solution for the crystal structure of the α‐phase, demonstrating a modulation of the Re—Re distances. The relatively small portion of the diffraction pattern accessed in the pressure‐dependent measurements does not allow for a detailed study of the crystal structure of α‐ReO₂ under pressure. Nonetheless, a shift and reduction in the (011) Bragg peak intensity between 0.4 and 1.2 GPa is observed, with correlation to a decrease in Re—Re distance modulation, as confirmed by EXAFS analysis in the same pressure range. This behavior reveals that α‐ReO₂ is a possible inner pressure gauge for future experiments up to 1.2 GPa.     

Synchrotron‐based spectroscopy of X‐ray channeling through hollow capillary microchannels inside glass plates

Here, soft X‐ray synchrotron radiation transmitted through microchannel plates is studied experimentally. Fine structures of reflection and XANES Si L‐edge spectra detected on the exit of silicon glass microcapillary structures under conditions of total X‐ray reflection are presented and analyzed. The phenomenon of the interaction of channeling radiation with unoccupied electronic states and propagation of X‐ray fluorescence excited in the microchannels is revealed. Investigations of the interaction of monochromatic radiation with the inner‐shell capillary surface and propagation of fluorescence radiation through hollow glass capillary waveguides contribute to the development of novel X‐ray focusing devices in the future.     

Suppression of the Verwey Transition by Charge Trapping

The Verwey transition in Fe₃O₄ nanoparticles with a mean diameter of 6.3 nm is suppressed after capping the particles with a 3.5 nm thick shell of SiO₂. By X‐ray absorption spectroscopy and its associated X‐ray magnetic circular dichroism this suppression can be correlated to localized Fe²⁺ states and a reduced double exchange visible in different site‐specific magnetization behavior in high magnetic fields. The results are discussed in terms of charge trapping at defects in the Fe₃O₄/ SiO₂ interface and the consequent difficulties in the formation of the common phases of Fe₃O₄. By comparison to X‐ray absorption spectra of bare Fe₃O₄ nanoparticles in course of the Verwey transition, particular changes in the spectral shape could be correlated to changes in the number of unoccupied d states for Fe ions at different lattice sites. These findings are supported by density functional theory calculations.     

An electrochemical cell with sapphire windows for operando synchrotron X‐ray powder diffraction and spectroscopy studies of high‐power and high‐voltage electrodes for metal‐ion batteries

A new multi‐purpose operando electrochemical cell was designed, constructed and tested on the Swiss–Norwegian Beamlines BM01 and BM31 at the European Synchrotron Radiation Facility. Single‐crystal sapphire X‐ray windows provide a good signal‐to‐noise ratio, excellent electrochemical contact because of the constant pressure between the electrodes, and perfect electrochemical stability at high potentials due to the inert and non‐conductive nature of sapphire. Examination of the phase transformations in the Li_1–xFe_0.5Mn_0.5PO₄ positive electrode (cathode) material at C/2 and 10C charge and discharge rates, and a study of the valence state of the Ni cations in the Li_1–xNi_0.5Mn_1.5O₄ cathode material for Li‐ion batteries, revealed the applicability of this novel cell design to diffraction and spectroscopic investigations of high‐power/high‐voltage electrodes for metal‐ion batteries.     

On the 40th anniversary of the journal X‐Ray Spectrometry

This journal, X‐Ray Spectrometry, celebrates its 40th anniversary this year. The state of the publications on X‐ray spectral analysis from 1972 onward is considered. The distribution of materials over countries is presented, as published in X‐Ray Spectrometry for 40 years, in 5‐year time intervals: 1972–1976, 1977–1981, and so on. The participation of Russian scientists contributing to the publications in this journal is discussed. Copyright © 2012 John Wiley & Sons, Ltd.     

An X‐ray Raman spectrometer for EXAFS studies on minerals: bent Laue spectrometer with 20 keV X‐rays

An X‐ray Raman spectrometer for studies of local structures in minerals is discussed. Contrary to widely adopted back‐scattering spectrometers using ≤10 keV X‐rays, a spectrometer utilizing ～20 keV X‐rays and a bent Laue analyzer is proposed. The 20 keV photons penetrate mineral samples much more deeply than 10 keV photons, so that high intensity is obtained owing to an enhancement of the scattering volume. Furthermore, a bent Laue analyzer provides a wide band‐pass and a high reflectivity, leading to a much enhanced integrated intensity. A prototype spectrometer has been constructed and performance tests carried out. The oxygen K‐edge in SiO₂ glass and crystal (α‐quartz) has been measured with energy resolutions of 4 eV (EXAFS mode) and 1.3 eV (XANES mode). Unlike methods previously adopted, it is proposed to determine the pre‐edge curve based on a theoretical Compton profile and a Monte Carlo multiple‐scattering simulation before extracting EXAFS features. It is shown that the obtained EXAFS features are reproduced fairly well by a cluster model with a minimal set of fitting parameters. The spectrometer and the data processing proposed here are readily applicable to high‐pressure studies.     

Full Protection for Graphene‐Incorporated Micro‐/Nanocomposites Containing Ultra‐small Active Nanoparticles: the Best Li‐Storage Properties

In recent years, graphene‐incorporated micro‐/nanocomposites represent one of the hottest developing directions for the composite materials. However, a large number of active nanoparticles (NPs) are still in the unprotected state in most constructed graphene‐containing designs, which will seriously impair the effects of the graphene additives. Here, a fully protected Fe₃O₄‐based micro‐/nanocomposite (G/Fe₃O₄@C) is rationally developed by carbon‐boxing the common graphene/Fe₃O₄ microparticulates (G/Fe₃O₄). The processes and results of full protection are tracked in detail and characterized by X‐ray diffraction, X‐ray photoelectron spectroscopy, and nitrogen absorption–desorption isotherms, as well as scanning and transition electron microscopy. When used as the anode for lithium‐ion batteries, the fully protected G/Fe₃O₄@C exhibits the best lithium‐storage properties in terms of the highest rate capabilities and the longest cycle life compared to the common G/Fe₃O₄ composites and commercial Fe₃O₄ products. These much improved properties are mainly attributed to its novel structural features including complete protection of active Fe₃O₄ nanoparticles by the surface carbon box, a robust conductive network composed of nitrogen‐doped graphene nanosheets, ultra‐small Fe₃O₄ NPs of 4–5 nm, abundant mesopores to accommodate the volume variation during cycling, and micrometer‐sized secondary particles.     

Trace element analysis of hairs in patients with dementia

The trace elements of scalp hair samples from ≥60‐year‐old dementia patients and normal persons have been studied by X‐ray absorption near‐edge spectroscopy (XANES) in fluorescent mode and wavelength‐dispersive X‐ray fluorescence spectrometry. Comparisons of hair trace element levels of age‐matched dementia patients and normal persons revealed significantly elevated amounts of calcium, chlorine and phosphorus in dementia patients relative to normal persons. The results of XANES measurements identify the chemical forms of deposited calcium and phosphorus in the hair samples of both dementia patients and normal persons to be calcium chloride (CaCl₂) and phosphate (PO₄^3?), respectively. The amount of sulfur in hairs of dementia patients was found to be not significantly different from that in normal persons. The sulfur K‐edge XANES spectra, however, show significantly higher accumulations of sulfur in the sulfate (SO₄^2?) form in hairs of Alzheimer's disease and Parkinson's disease dementia patients. This study presents the possible roles of calcium, chlorine, phosphorus and sulfur in the etiology of dementia in elderly patients.     

On the correlation between the X‐ray absorption chemical shift and the formal valence state in mixed‐valence manganites

Here the correlation between the chemical shift in X‐ray absorption spectroscopy, the geometrical structure and the formal valence state of the Mn atom in mixed‐valence manganites are discussed. It is shown that this empirical correlation can be reliably used to determine the formal valence of Mn, using either X‐ray absorption spectroscopy or resonant X‐ray scattering techniques. The difficulties in obtaining a reliable comparison between experimental XANES spectra and theoretical simulations on an absolute energy scale are revealed. It is concluded that the contributions from the electronic occupation and the local structure to the XANES spectra cannot be separated either experimentally or theoretically. In this way the geometrical and electronic structure of the Mn atom in mixed‐valence manganites cannot be described as a bimodal distribution of the formal integer Mn³⁺ and Mn⁴⁺ valence states corresponding to the undoped references.     

Nondestructive investigation of interface states in high‐k oxide films on Ge substrate using X‐ray absorption spectroscopy

The unoccupied electronic structures of 5 nm thick high permittivity (k) oxides (HfO₂, ZrO₂, and Al₂O₃) and SiO₂ films on Ge substrates were examined using O K‐edge X‐ray absorption spectroscopy. Comparative studies with those on Si substrates showed contrasts in the conduction bands, which should be due to the formation of interface states. In the Al₂O₃ and SiO₂ films, GeO₂ layers are formed at the interface and they suppress in part the formation of detrimental germanate phases. In contrast, in the HfO₂ and ZrO₂ films, no signature of the Ge‐oxide phase is observed but some germanate phases are expected to prevail, suggesting a degradation of the gate oxide characteristics. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Collimating Montel mirror as part of a multi‐crystal analyzer system for resonant inelastic X‐ray scattering

Advances in resonant inelastic X‐ray scattering (RIXS) have come in lockstep with improvements in energy resolution. Currently, the best energy resolution at the Ir L₃‐edge stands at ～25 meV, which is achieved using a diced Si(844) spherical crystal analyzer. However, spherical analyzers are limited by their intrinsic reflection width. A novel analyzer system using multiple flat crystals provides a promising way to overcome this limitation. For the present design, an energy resolution at or below 10 meV was selected. Recognizing that the angular acceptance of flat crystals is severely limited, a collimating element is essential to achieve the necessary solid‐angle acceptance. For this purpose, a laterally graded, parabolic, multilayer Montel mirror was designed for use at the Ir L₃‐absorption edge. It provides an acceptance larger than 10 mrad, collimating the reflected X‐ray beam to smaller than 100 µrad, in both vertical and horizontal directions. The performance of this mirror was studied at beamline 27‐ID at the Advanced Photon Source. X‐rays from a diamond (111) monochromator illuminated a scattering source of diameter 5 µm, generating an incident beam on the mirror with a well determined divergence of 40 mrad. A flat Si(111) crystal after the mirror served as the divergence analyzer. From X‐ray measurements, ray‐tracing simulations and optical metrology results, it was established that the Montel mirror satisfied the specifications of angular acceptance and collimation quality necessary for a high‐resolution RIXS multi‐crystal analyzer system.     

Three‐dimensional imaging of chemical phase transformations at the nanoscale with full‐field transmission X‐ray microscopy

The ability to probe morphology and phase distribution in complex systems at multiple length scales unravels the interplay of nano‐ and micrometer‐scale factors at the origin of macroscopic behavior. While different electron‐ and X‐ray‐based imaging techniques can be combined with spectroscopy at high resolutions, owing to experimental time limitations the resulting fields of view are too small to be representative of a composite sample. Here a new X‐ray imaging set‐up is proposed, combining full‐field transmission X‐ray microscopy (TXM) with X‐ray absorption near‐edge structure (XANES) spectroscopy to follow two‐dimensional and three‐dimensional morphological and chemical changes in large volumes at high resolution (tens of nanometers). TXM XANES imaging offers chemical speciation at the nanoscale in thick samples (>20 µm) with minimal preparation requirements. Further, its high throughput allows the analysis of large areas (up to millimeters) in minutes to a few hours. Proof of concept is provided using battery electrodes, although its versatility will lead to impact in a number of diverse research fields.     

Soft X‐ray absorption spectroscopy and resonant inelastic X‐ray scattering spectroscopy below 100 eV: probing first‐row transition‐metal M‐edges in chemical complexes

X‐ray absorption and scattering spectroscopies involving the 3d transition‐metal K‐ and L‐edges have a long history in studying inorganic and bioinorganic molecules. However, there have been very few studies using the M‐edges, which are below 100 eV. Synchrotron‐based X‐ray sources can have higher energy resolution at M‐edges. M‐edge X‐ray absorption spectroscopy (XAS) and resonant inelastic X‐ray scattering (RIXS) could therefore provide complementary information to K‐ and L‐edge spectroscopies. In this study, M_2,3‐edge XAS on several Co, Ni and Cu complexes are measured and their spectral information, such as chemical shifts and covalency effects, are analyzed and discussed. In addition, M_2,3‐edge RIXS on NiO, NiF₂ and two other covalent complexes have been performed and different d–d transition patterns have been observed. Although still preliminary, this work on 3d metal complexes demonstrates the potential to use M‐edge XAS and RIXS on more complicated 3d metal complexes in the future. The potential for using high‐sensitivity and high‐resolution superconducting tunnel junction X‐ray detectors below 100 eV is also illustrated and discussed.     

An attempt at kidney stone analysis with the application of synchrotron radiation

X‐ray absorption near‐edge spectroscopy (XANES) is a spectroscopic technique using synchrotron light to determine the valence state of excited atoms as well as the electronegativity of their neighbouring atoms. XANES spectra can provide information about the chemical bond in the second coordination shell of the excited atom. In this study, XANES spectra of unknown compounds from human kidney stones were recorded around the K‐edges of sulfur, phosphorus and calcium. The XANES results agree well with the diffractogram data of the same stones obtained through an X‐ray powder diffraction (XRPD) technique. By comparing the measurement techniques presented here, it is shown that XANES requires a smaller amount of each sample than XRPD for analysis.     

Early commissioning results for spectroscopic X‐ray Nano‐Imaging Beamline BL 7C sXNI at PLS‐II

For spectral imaging of chemical distributions using X‐ray absorption near‐edge structure (XANES) spectra, a modified double‐crystal monochromator, a focusing plane mirrors system and a newly developed fluorescence‐type X‐ray beam‐position monitoring and feedback system have been implemented. This major hardware upgrade provides a sufficiently stable X‐ray source during energy scanning of more than hundreds of eV for acquisition of reliable XANES spectra in two‐dimensional and three‐dimensional images. In recent pilot studies discussed in this paper, heavy‐metal uptake by plant roots in vivo and iron's phase distribution in the lithium–iron–phosphate cathode of a lithium‐ion battery have been imaged. Also, the spatial resolution of computed tomography has been improved from 70 nm to 55 nm by means of run‐out correction and application of a reconstruction algorithm.     

A large‐volume gas cell for high‐energy X‐ray reflectivity investigations of interfaces under pressure

A cell for the investigation of interfaces under pressure is presented. Given the pressure and temperature specifications of the cell, P≤ 100 bar and 253 K ≤T≤ 323 K, respectively, high‐energy X‐rays are required to penetrate the thick Al₂O₃ windows. The CH₄(gas)/H₂O(liquid) interface has been chosen to test the performance of the new device. The measured dynamic range of the high‐energy X‐ray reflectivity data exceeds 10^?8, thereby demonstrating the validity of the entire experimental set‐up.     

X‐ray photon correlation spectroscopy in systems without long‐range order: existence of an intermediate‐field regime

Successful X‐ray photon correlation spectroscopy studies often require that signals be optimized while minimizing power density in the sample to decrease radiation damage and, at free‐electron laser sources, thermal impact. This suggests exploration of scattering outside the Fraunhofer far‐field diffraction limit d²/λR, where d is the incident beam size, λ is the photon wavelength and R is the sample‐to‐detector distance. Here it is shown that, in an intermediate regime d²/λ > Rdξ/λ, where ξ is the structural correlation length in the material, the ensemble averages of the scattered intensity and of the structure factor are equal. Similarly, in the regime d²/λ > Rdξ(τ)/λ, where ξ(τ) is a time‐dependent dynamics length scale of interest, the ensemble‐averaged correlation functions g₁(τ) and g₂(τ) of the scattered electric field are also equal to their values in the far‐field limit. This broadens the parameter space for X‐ray photon correlation spectroscopy experiments, but detectors with smaller pixel size and variable focusing are required to more fully exploit the potential for such studies.     

Concept of a spectrometer for resonant inelastic X‐ray scattering with parallel detection in incoming and outgoing photon energies

A spectrometer for resonant inelastic X‐ray scattering (RIXS) is proposed where imaging and dispersion actions in two orthogonal planes are combined to deliver a full two‐dimensional map of RIXS intensity in one shot with parallel detection at incoming hv_in and outgoing hv_out photon energies. Preliminary ray‐tracing simulations with a typical undulator beamline demonstrate a resolving power well above 11000 with both hv_in and hv_out near 930 eV, with a vast potential for improvement. Combining this instrument – nicknamed hv² spectrometer – with an X‐ray free‐electron laser source simplifies its technical implementation and enables efficient time‐resolved RIXS experiments.     

Relationship between the structural distortion and the Mn electronic state in La1−xCaxMnO3: a Mn K‐edge XANES study

A theoretical study of the X‐ray absorption near‐edge structure (XANES) spectra at the Mn K‐edge in the La_1?xCa_xMnO₃ series is reported. The relationship between the edge shift, the Ca–La substitution and the distortion of the MnO₆ octahedra in these systems has been studied. It is shown that, by correctly considering these effects simultaneously, the experimental XANES data are consistent with the presence of two different Mn local environments in the intermediate La_1?xCa_xMnO₃ compounds. By taking into account the energy shift associated with the modification of the MnO₆ distortion as Ca substitutes for La, it is possible to reproduce the XANES spectra of the intermediate‐doped compounds starting from the experimental spectra of the end‐members LaMnO₃ and CaMnO₃. These results point out the need to re‐examine the conclusions derived in the past from the simple analysis of the Mn K‐edge XANES edge‐shift in these materials. In particular, it is shown that the modification of the Mn K‐edge absorption through the La_1?xCa_xMnO₃ series is well reproduced by considering the simultaneous presence of both distorted and undistorted octahedra and, consequently, that the existence of charge‐ordering phenomena cannot be ruled out from the XANES data.