Fe–N/C nanofiber electrocatalysts with improved activity and stability for oxygen reduction in alkaline and acid solutions

Fe–N/C nanofiber (Fe–N/CNF) electrocatalysts were prepared by impregnating electrospun polyacrylonitrile nanofibers with iron nitrate (Fe(NO₃)₃) solution and subsequent heat treatment, exhibiting improved activity and stability during oxygen reduction reaction (ORR) both in 0.1 M KOH (pH?=?13) and 0.5 M H₂SO₄ (pH?=?0) electrolyte solutions. Higher treatment temperature and NH₃ atmosphere were preferred by the Fe–N/CNF catalysts, and especially the concentration of Fe(NO₃)₃ solution exerted great effects on the surface morphology, structure, and thus electrocatalytic performance of the catalysts. The Fe–N/CNFs prepared using 0.5 wt% Fe(NO₃)₃ solution showed relatively higher ORR activity in alkaline and acid solutions and better stability especially in 0.5 M H₂SO₄ solution than the catalyst without Fe, probably because Fe could promote the graphitization of the polymer-converted carbon species, enhancing the resistance to electrochemical oxidation and thus the stability of the Fe–N/CNF catalysts.     

Co-precipitation spray-drying synthesis and electrochemical performance of stabilized LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode materials

In this paper, the LiNi_0.5Mn_1.5O₄ cathode materials of lithium-ion batteries are synthesized by a co-precipitation spray-drying and calcining process. The use of a spray-drying process to form particles, followed by a calcination treatment at the optimized temperature of 750 °C to produce spherical LiNi_0.5Mn_1.5O₄ particles with a cubic crystal structure, a specific surface area of 60.1 m² g^?1, a tap density of 1.15 g mL^?1, and a specific capacity of 132.9 mAh g^?1 at 0.1 C. The carbon nanofragment (CNF) additives, introduced into the spheres during the co-precipitation spray-drying period, greatly enhance the rate performance and cycling stability of LiNi_0.5Mn_1.5O₄. The sample with 1.0 wt.% CNF calcined at 750 °C exhibits a maximum capacity of 131.7 mAh g^?1 at 0.5 C and a capacity retention of 98.9% after 100 cycles. In addition, compared to the LiNi_0.5Mn_1.5O₄ material without CNF, the LiNi_0.5Mn_1.5O₄ with CNF demonstrates a high-rate capacity retention that increases from 69.1% to 95.2% after 100 cycles at 10 C, indicating an excellent rate capability. The usage of CNF and the synthetic method provide a promising choice for the synthesis of a stabilized LiNi_0.5Mn_1.5O₄ cathode material.

Open image in new window

Graphical Abstract Micro/nanostructured LiNi_0.5Mn_0.5O₄ cathode materials with enhanced electrochemical performances for high voltage lithium-ion batteries are synthesized by a co-precipitation spray-drying and calcining routine and using carbon nanofragments (CNFs) as additive.

     

Rapid separation of nickel for 59Ni and 63Ni activity measurement in radioactive waste samples

A separation procedure of Ni has been described for the quantification of ⁵⁹Ni and ⁶³Ni in radioactive wastes discharged from nuclear power plants and various research activities related to the nuclear fuel cycle. For a rapid separation of the Ni-nuclides in sixteen sample solutions in 0.2 M NH₄-oxalate, a separation system composed of a peristaltic pump with sixteen channels and the same number of Ni–Resin columns was constructed. After sorption of the Ni-nuclides by sequentially passing 100 mL of the sample solution in 0.2 M NH₄-oxalate, 130 mL of 0.1 M NH₄-oxalate solution and 10 mL of deionized water as a wash into the columns, these were purely recovered by passing 10 mL of 9 M HCl into the Ni–Resin columns stacked in series on the anion exchange resin columns. The separation of the Ni-nuclides in sixteen sample solutions can be achieved within 7 h. The chemical yield of the proposed procedure is 92.3 ± 0.8 % (n = 5) and the gravimetric recovery in the preparation stage of the Ni-nuclide sources is also acceptable, 88.5 ± 1.3 % (n = 5).     

Viscosities of Binary and Ternary Mixtures of Water,Alcohol, Acetone,and Hexane

This articles studied and determined the viscosities of the binary mixtures of water–methanol, water–ethanol, water–propanol, water–acetone, acetone–ethanol, methanol–ethanol, and acetone–hexane and the ternary mixtures of water–methanol–ethanol and water–ethanol–acetone at 20°C. It is shown that the mixing of water with the alcohols and acetone resulted in a positive deviation of viscosity, which reached the maximum value at the water mole fraction x ₁ ～ 0.7 for water–methanol, x ₁ ～ 0.72 for water–ethanol, x ₁ ～ 0.74 for water–propanol, and x ₁ ～ 0.83 for water–acetone binary mixture. This viscosity deviation can be mainly attributed to the formation of micelles of alcohol or acetone molecules in water because of the hydrophobic attraction between the hydrocarbon chains. The micelle surfaces are surrounded by hydration layers, leading to the positive viscosity deviation in the liquid mixtures because the water in hydration layers has a much higher viscosity than bulk water. Also, the contrary observation was found in the binary mixtures of acetone–ethanol and acetone–hexane, having a negative viscosity deviation.     

Preparation,molecular modeling and biodistribution of 99mTc-phytochlorin complex

Phytochlorin [21H, 23H-Porphine-7-propanoicacid, 3-carboxy-5-(carboxymethyl)13-ethenyl-18-ethyl-7,8-dihydro-2,8,12,17-tetramethyl-,(7S,8S)] was labeled with ^99mTc and the factors affecting the labeling yield of ^99mTc-phytochlorin complex were studied in details. At pH 10, ^99mTc-phytochlorin complex was obtained with a high radiochemical yield of 98.4 ± 0.6 % by adding ^99mTc to 100 mg phytochlorin in the presence of 75 μg SnCl₂·2H₂O after 30 min reaction time. The molecular modeling study showed that the structure of ^99mTc-phytochlorin complex presents nearly linear HO–Tc–OH unit with an angle of 179.27° and a coplanar Tc(N1N2N3N4) unit. Biodistribution of ^99mTc-phytochlorin complex in tumor bearing mice showed high T/NT ratio (T/NT = 3.65 at 90 min post injection). This preclinical study showed that ^99mTc-phytochlorin complex is a potential selective radiotracer for solid tumor imaging and afford it as a new radiopharmaceutical suitable to proceed through the clinical trials for tumor imaging.     

Effect of fluorination on the stability of carbon nanofibres in organic solvents

Beneficial effects of fluorination on the stability of carbon nanofibre (CNF) dispersion in organic solvents as a function of time are evidenced. Because of their excellent friction properties, fluorinated CNFs (CF_0.85) can be used as nanoparticles of tribo-active phase in lubrication; however, they have to be added into a matrix. We have shown that mixtures of CF_0.85 are more stable than CNF solutions. Investigations by ultraviolet–visible spectroscopy have been carried out 2 h after sonication and after an ageing of 4 months. Hansen solubility theory was used, and after ageing, tribological and Raman spectroscopy experiments showed no significant modification of physicochemical properties of the CF_0.85.     

Cellulose hydrolysis catalyzed by highly acidic lignin-derived carbonaceous catalyst synthesized via hydrothermal carbonization

Acidic carbonaceous solids were synthesized from mass pine alkali lignin via hydrothermal carbonization followed by sulfonation. Hydrothermal carbonization of lignin in the presence of acrylic acid (LAHC-SO₃H) provided many more carboxylic groups than that in the absence of acrylic acid, allowing subsequent sulfonation to produce a highly active and stable catalyst for cellulose hydrolysis in the [BMIM]Cl-H₂O solvent system. The hydrochar and catalyst were characterized using field emission scanning electron microscopy, X-ray diffractometer, X-ray photoelectron spectroscopy, thermal gravimetric analysis, Fourier transform infrared spectrometer, Brunauer–Emmett–Teller and acid–base titration. Results showed that a high acid content of 5.48 mmol/g, including carboxylic group (2.85 mmol/g), phenolic hydroxyl group (1.05 mmol/g) and sulfonic acid group (1.58 mmol/g), contributed significantly to the highly efficient hydrolysis of cellulose. Further, it was found that addition of trace water in [BMIM]Cl was favorable to cellulose hydrolysis. The highest yield (75.4%) of total reducing sugar (TRS) obtained in [BMIM]Cl-H₂O at a mass ratio of 100:1 was more than twice that (36.1%) achieved in [BMIM]Cl without water; the corresponding reaction conditions were 50 mg of microcrystalline cellulose, 30 mg of catalyst, 1.0 g of [BMIM]Cl, 10 mg of H₂O, reaction temperature of 130 °C and reaction time of 2 h. Furthermore, the TRS yield with 5 cycles for LAHC-SO₃H was higher than 68.1%, and the catalytic activity of catalyst could be fully recovered (74.0% of TRS yield) easily by regeneration.     

Computational design of tetrahedral silsesquioxane-based porous frameworks with diamond-like structure as hydrogen storage materials

A novel type of three-dimensional (3D) tetrahedral silsesquioxane-based porous frameworks (TSFs) with diamond-like structure was computationally designed using the density functional theory (DFT) and classical molecular mechanics (MM) calculations. The hydrogen adsorption and diffusion properties of these TSFs were evaluated by the methods of grand canonical Monte Carlo (GCMC) and molecular dynamics (MD) simulations. The results reveal that all designed materials possess extremely high porosity (87–93 %) and large H₂ accessible surface areas (5,268–6,544 m² g^?1). Impressively, the GCMC simulation results demonstrate that at 77 K and 100 bar, TSF-2 has the highest gravimetric H₂ capacity of 29.80 wt%, while TSF-1 has the highest volumetric H₂ uptake of 65.32 g L^?1. At the same time, the gravimetric H₂ uptake of TSF-2 can reach up to 4.28 wt% at the room temperature. The extraordinary performances of these TSF materials in hydrogen storage made them enter the rank of the top hydrogen storage materials so far.     

Effect of fsDNA on chemiluminescence characteristics of luminol–H2O2 system catalyzed by Mn(III)–Tetrakis (4-sulfonatophenyl)-porphyrin

In the present work, the effect of fsDNA (fish sperm DNA) on kinetic parameters of chemiluminescence (CL) of the luminol–hydrogen peroxide system catalyzed by Mn(III)–Tetrakis (4-sulfonatophenyl)-porphyrin was investigated. These parameters including pseudo first-order rise and fall rate constant for the chemiluminescence burst, maximum level intensity, time to reach maximum intensity, total light yield, and values of the intensity at maximum CL were evaluated by computer fitting of the resulted intensity–time plots. Results reveal that CL parameters are dramatically affected due to interaction of metalloporphyrin with DNA. In order to observe quenching effect of DNA on CL intensity, Stern–Volmer plot with k _Q value of 1.18 × 10⁵ M^?1 was calculated in the quencher concentration range of 4 × 10^?6–8.5 × 10^?5 M.     

Selective conversion of cellulose to levulinic acid and furfural in sulfolane/water solvent

Direct conversion of cellulose into levulinic acid and furfural in sulfolane media with the aid of water and H₂SO₄ was performed at 140–220 °C under the pressures of 0–1.5 MPa. This approach could obtain 72.5 mol% levulinic acid and 11.5 mol% furfural formation under an optimal condition in which the mass ratio of sulfolane, water and H₂SO₄ was 90:10:1. It was found that the decrease of water content led to an increasing yield of furfural and that the maximum furfural yield (51.1 mol%) could be obtained in the absence of water. The synergism of sulfolane and water in the selective liquefied system was demonstrated to be responsible for not only reinforced effect of optimizing and isolating the target products but also for reducing re-polymerization and side reactions. Furthermore, sulfolane in our case could be recycled and re-used for the conversion of cellulose with the same yield, which shed light on the remarkable potential for future industrial application.     

Effect of preparation process of microfibrillated cellulose-reinforced polypropylene upon dispersion and mechanical properties

Microfibrillated cellulose (MFC)-reinforced polypropylene (PP) was prepared via two engineering approaches: disintegration of the pulp by a bead mill followed by a melt-compounding process with PP (B-MFC-reinforced PP); and disintegration of the pulp mixed with PP by a twin screw extruder followed by a melt-compounding process (T-MFC-reinforced PP). The effects that the engineering process and the microfibrillation of the pulp had upon the dispersion and mechanical properties were investigated through tensile tests, rheological analysis and X-ray computed tomography. The bead-milling method enabled a uniform microfibrillation of the pulp to under 100 nm, which corresponded to a surface area of 133–146 m²/g for the pulp, found by the Brunauer–Emmett–Teller (BET) analysis. The T-MFC-reinforced PP with 30 wt% MFC content exhibited a tensile modulus of 5.3 GPa and a strength of 85 MPa, whereas the B-MFC-reinforced PP composites with the same content of MFC exhibited values of 4.1 GPa and 59.6 MPa, respectively. Rheological analysis revealed that the complex viscosity and storage modulus at 170 °C of T-MFC-reinforced PP with 30 wt% MFC content are 5–7 and 5–8 times higher than that of B-MFC-reinforced PP, respectively. This indicated that T-MFC was more dispersed in the PP than B-MFC. Therefore, T-MFC produced a more rigid interconnected network in the matrix during the melting state than B-MFC.     

Effective removal of ciprofloxacin from aqueous solutions using magnetic metal–organic framework sorbents: mechanisms,isotherms and kinetics

Metal–organic framework sorbents [MIL-100(Fe), MOF-235(Fe)], Fe₃O₄ nanoparticles and metal–organic framework loaded on iron oxide nanoparticles [Fe₃O₄@MIL-100(Fe) and Fe₃O₄@MOF-235(Fe)] were prepared and examined for ciprofloxacin (CIP) removal. The results showed that sorption kinetics of CIP by Fe₃O₄@MIL-100(Fe) follows the Elovich and pseudo-second-order models indicating that the sorption is both chemisorption and physical adsorption, whereas the sorption to other sorbents occurs mainly by physical sorption. The sorption isotherm studies revealed that Langmuir model provided the best fit to all the experimental data. The thermodynamic studies showed that CIP removal is spontaneous (ΔG° = 2.28 kJ/mol) and endothermic (ΔH° = 18.39 kJ/mol). It was also found that among the sorbents investigated for CIP removal, Fe₃O₄@MIL-100(Fe) has the highest maximum monolayer adsorption capacity of 322.58 mg/g.     

Dielectric and switching properties of a highly tilted AFLC material (S)-(+)-4-(1-methylheptyloxycarbonyl)-2,3-difluorophenyl 4′-[3-(2,2,3,3,4,4,4-heptafluorobutoxy)prop-1-oxy]biphenyl-4-carboxylate

Thermodynamic, dielectric, optical and switching parameters of a single-phase antiferroelectric (AF) liquid crystalline material (S)-(+)-4-(1-methylheptyloxycarbonyl)-2,3-difluorophenyl 4′-[3-(2,2,3,3,4,4,4-heptafluorobutoxy)prop-1-oxy]biphenyl-4-carboxylate have been studied. These studies show wide temperature range (~97.8°C–25.3°C) of AF SmC^*_A phase in the material. The dielectric studies have been carried out in the frequency range of 1 Hz–35 MHz under planar anchoring conditions of the molecules. The dielectric spectrum of the SmC^*_A phase exhibits three relaxation modes due to the collective as well as individual molecular processes. Relaxation frequencies of these modes lie in the range of kHz–MHz regions. Relative permittivity of the material (at 10 kHz) varies from ~8.8 at 98.8°C to 9.9 at 41.0°C. Maximum tilt of the molecule in the SmC^*_A phase is ~43°C. Spontaneous polarisation, switching time and rotational viscosity have also been determined. The maximum value of P_S is ~439 nC/cm² and switching time is the order of 1–5 millisecond, whereas viscosity is moderate.     

Dispersion of single-walled carbon nanotubes in aqueous solution with a thermo-responsive pentablock terpolymer

Single-walled carbon nanotubes (SWNTs) were dispersed in pure water with a thermo-responsive amphiphilic PNIPAM₁₅₀-F108-PNIPAM₁₅₀ pentablock terpolymer in comparison with its precursor PEO₁₃₆-PPO₄₅-PEO₁₃₆ (F108) triblock copolymer. The stability, dispersibility, and thermo-responsive behaviors of the polymer/SWNT hybrids were characterized by UV–vis–NIR spectroscopy, thermal gravimetric analysis, viscosity measurement, Raman spectroscopy, and high-resolution transmission electron microscopy. The pentablock/SWNT hybrids showed superior ability in stabilization over F108/SWNT hybrids, and no sign of sedimentation was found at room temperature for 6 weeks or even 2 months of storage. The pentablock terpolymer can efficiently disperse SWNTs into individual tubes or small bundles with average diameter of about 5 nm, and their chains were helically wrapped onto the nanotube surface, whereas the larger bundles of the nanotubes with sizes of 15–25 nm were observed in F108/SWNT hybrids. Moreover, the pentablock/SWNT hybrids switched reversibly between the well-exfoliated and the aggregated states when cyclically increasing and decreasing temperature.     

Aggregate Conformation and Rheological Properties of Didodecyldimethylammonium Bromide in Aqueous Solution

Aggregation behavior of didodecyldimethylammonium bromide (DDAB) in aqueous solution was investigated using negative-staining and freeze-fracture transmission electron microscopy (TEM) methods. With the concentration increase, the vesicle size enlarged from the range of 100–200 nm to 500–3000 nm and the structure transform from unilamella to multilamella. Rheological and viscosity measurement results indicated that the system exhibited a gel-like material characteristic and shearing thinning in property, as shown that the apparent viscosity decreased gradually during the shear rate ascended from 1 × 10^?4–1 × 10⁴ s^?1. Furthermore, the relationship between aggregate conformation and solution rheological properties was discussed.     

Magnetic nanofibrous polyaniline nanocomposite for solid-phase extraction of naproxen from biological samples prior to its spectrofluorimetric determination

Nanofibrous polyaniline–magnetite (PANI/Fe₃O₄) nanocomposite was in situ prepared through adsorption of magnetite nanoparticles onto PANI nanofibers surface and utilized as an efficient sorbent for magnetic solid-phase extraction of naproxen from water and biological samples, followed a desorption step and spectrofluorimetric determination. Field-emission scanning electron microscopy, transmission electron microscopy, Fourier-transform infrared spectroscopy, thermal gravimetric analysis and X-ray diffraction techniques were employed for characterization of the prepared nanocomposite. The important parameters influencing the extraction efficiency including PANI/Fe₃O₄ mass ratio, adsorbent dose, extraction time, sample solution pH, ionic strength, type and volume of desorption solvent and the elution time were studied and optimized. The investigated nanocomposite was successfully applied to the extraction of naproxen in spiked tap water, urine and plasma samples, with a relative recovery in the range of 90–98%. The reusability of PANI/Fe₃O₄ was examined for ten successive cycles, and the results confirm that the efficiency did not change significantly. A linear calibration plot was obtained in the range of 40–1000 ng mL^?1 with a limit of detection about 17 ng mL^?1 under the optimum conditions. The relative standard deviation (RSD) was found to be 2.34% (n = 8, concentration level of 100 ng mL^?1). The kinetics and thermodynamics of the extraction process were also studied.     

Influence of cellulose nanofibers on the rheological behavior of silica-based shear-thickening fluid

In this work, the influence of cellulose nanofibers (CNFs) on the rheological behavior of silica-based shear-thickening fluid (STF) is investigated. CNFs of 150–200 nm in diameter were extracted from cotton fibers using a supermasscolloider. CNF-reinforced STF of different concentrations (0.1–0.3 wt.%) was prepared via an ultrasonication technique. The presence of CNFs and their interaction with the silica nanoparticles in the STF were analyzed using SEM and FTIR. The addition of a minute quantity of CNF to the STF (0.3% CNF-reinforced STF) caused a marked increase in the peak viscosity, from 36.8 (unmodified STF) to 139.0 Pa s (0.2% CNF-reinforced STF), and a concomitant decrease in the critical shear rate from 33.45 to 14.8 s^?1 . The presence of a large number of hydroxyl groups on the CNFs enhanced their interaction with the nanoparticles via hydrogen bonding, which induced shear thickening. The mechanism of the interaction between silica nanoparticles and CNF was also demonstrated. Oscillatory dynamic rheological analysis showed that the addition of even a small amount of CNF led to higher elastic behavior in the system at lower shear rates. In contrast, a more viscous nature was demonstrated at higher angular frequencies. As the concentration of  nanofibers in the STFs increased, the crossover point between storage and loss modulus shifted to higher angular frequencies, implying stronger interaction between the constituents of the STF. The dynamic viscosity profile of all samples also exhibited shear-thickening behavior.     

Synthesis and electrochemical characterization of duo doped spinels (zinc and praseodymium) for use in lithium rechargeable batteries

LiMn₂O₄ and LiZn_xPr_yMn_2?x?yO₄ (x = 0.10–0.24; y = 0.01–0.10) powders have been synthesized by sol–gel method using palmitic acid as chelating agent. The synthesized samples have been subjected to thermo gravimetric and differential thermal analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray analysis (EDAX). The sol–gel route bestows low calcination temperature, shorter heating time, high purity, good control over stoichiometry, small particle size, high surface area, good surface morphology and better homogeneity, The XRD patterns reveal high degree of crystallinity and better phase purity. SEM and TEM images exhibit nano-sized nature particles with good agglomeration. EDAX peaks of Zn, Pr, Mn and O have been confirmed in actual compositions of LiMn₂O₄ and LiZn_xPr_yMn_2?x?yO₄. Charge–discharge studies of pristine spinel LiMn₂O₄ heated at 850 °C delivers discharge capacity of 132 mA h g^?1 corresponding to columbic efficiency of 73 % during the first cycle. At the end of 10th cycles, it delivers maximum discharge capacity of 112 mA h g^?1 with columbic efficiency of 70 % and capacity fade of 0.15 mA h g^?1 cycle^?1 over the investigated 10 cycles. Inter alia, all dopants concentrations, LiZn_0.10Pr_0.10Mn_1.80O₄ exhibits the better cycling performance (1st cycle discharge capacity: 130 mA h g^?1 comparing to undoped spinel 132 mA h g^?1) corresponding to columbic efficiency of 73 % with capacity fade of 0.12 mA h g^?1 cycle^?1.     

Synthesis of CaWO4:Er3+@SiO2 and CaWO4:Tm3+@SiO2 nano-particles via a combustion pathway and study of their optical properties

Use of citric acid as a chelating agent and fuel, ammonium nitrate as fuel, boric acid as flux material and silica as supports, CaWO₄:Ln³⁺@SiO₂ (Ln = Er and Tm) nanoparticles were synthesized via a combustion reaction at 800 °C. Characterization of the samples was performed by X-ray diffractometer (XRD), reflectance UV–Vis spectrophotometer, fluorescence spectrophotometer (PL) and transmission electron microscope (TEM). XRD patterns showed that tetragonal crystalline structure of scheelite and silica supports were formed, and that the formation of a silica support could enhance the luminescence intensity of CaWO₄:Ln³⁺. The reflectance UV–Vis and PL spectra indicated the broad absorption band of WO₄ ^2? groups about 240 nm, the WO₄ ^2? wide excitation band with maximum at 240 nm, a broad emission band of WO₄ ^2? with maximum about 420 nm, and characteristic emissions of Ln³⁺ ions. According to the TEM analysis, CaWO₄:Er³⁺@SiO₂ and CaWO₄:Tm³⁺@SiO₂ nanoparticles have almost the same morphology with average particle sizes about 50 nm.     

Styrene-Maleic Anhydride Copolymer Esters as Flow Improvers of Waxy Crude Oil

Four comb-like copolymers derived from styrene-maleic anhydride copolymer were prepared and characterized by FTIR, ¹H-NMR and elemental analysis. The molecular weight was determined using GPC and their intrinsic viscosity was measured. The prepared polymers were investigated as pour point depressants and flow improvers for waxy crude oil and it was found that, the maximum depression was obtained by the sample that has long branch chain (PPD4) from 27°C to ?3°C (ΔPP = 30°C, at 10000 ppm). While, the minimum depression was exhibited by short branch chain, PPD1 (ΔPP = 21°C) at the same conditions. The effect of these polymers on the rheology and flow properties of Qarun waxy crude oil was investigated. It was found that the Bingham yield value (τ_β) decreased from 6.0 pa.s. to 0.5 pa.s. for PPD4 at 27°C and 10,000 ppm. The dynamic viscosity also decreased from 110 m pa.s. to 24 m pa.s. for the same sample and the same conditions.