钾助剂对F-T合成铁基催化剂浆态床反应性能的影响

 采用连续共沉淀与喷雾干燥成型技术相结合的方法制备了不同K助剂含量的系列微球形Fe/Cu/K/SiO2催化剂(K/Fe质量比为0.010～0.058),采用低H2/CO比的合成气于典型的工业反应条件下(523～533 K, 1.5 MPa, H2/CO=0.67)进行了长期的浆态相F-T合成(FTS)反应性能评价. 结果表明: K助剂的添加可增大催化剂活性,提高C5+、总的烯烃、有机含氧化合物及CO2的选择性,并促进水煤气变换反应,但过高的K含量易使催化剂反应稳定性变差. 适中的K含量为K/Fe＝0.030,该K含量催化剂的660 h浆态床FTS反应性能评价结果显示,该催化剂具有较高的催化活性和C5+选择性,产物分布较合理,长期运行稳定性好,反应后卸载下的催化剂形貌观测表明该催化剂还具有较好的抗磨损性能. 除K助剂的化学效应起主导作用外,催化剂的织构性质尤其是孔结构可能对催化剂的催化性能也有一定的影响,并引起K/Fe＝0.045时铁基催化剂对FTS产物选择性和水煤气变换反应活性的部分调变.     

费托合成 Fe基催化剂中铁物相与活性的关系

 采用连续共沉淀和喷雾干燥相结合的方法制备了微球形 Fe 基催化剂, 采用 N2 吸附-脱附、X 射线衍射和穆斯堡尔谱等手段, 考察了催化剂在不同还原条件下铁物相的转变, 并在浆态床反应器中评价了催化剂的费-托合成 (FTS) 反应性能. 结果表明, Fe 基催化剂在合成气气氛下首先从α-Fe2O3 转变为 Fe3O4, 然后转变为铁碳化物 (FexC); 还原压力的增大有利于 α-Fe2O3 向 Fe3O4 的转变, 而抑制 Fe3O4 向 FexC 的转变; 还原空速的增加则促进 Fe3O4 转变为 FexC. 催化剂的 FTS 反应活性随着催化剂中 Fe3O4 含量的增加而逐渐下降, 而随着 FexC 含量的增加而逐渐上升.     

聚乙二醇介质中纳米铁基催化剂上的费托合成

 采用化学还原法在纯水中制备了纳米铁基催化剂, 将其直接分散到液态聚乙二醇 (PEG) 中进行费托合成 (FTS) 反应. 透射电子显微镜、X 射线衍射、穆斯堡尔谱和 X 射线光电子能谱等结果表明, 还原态催化剂粒径在 30~65 nm, 主要由无定形的 Fe-B 和α-Fe 组成, 其中 B 部分电子向 Fe 转移. 反应过程中, 无定形的 Fe-B 首先快速转变为 α-Fe, 而 α-Fe 很容易发生碳化或氧化, 最终转变为 Fe3O4 和碳化铁. PEG 能有效抑制纳米粒子的聚集长大, 反应后催化剂粒径减小为 20~55 nm. 在 3.0 MPa, V( H2)/V(CO) = 2 和 200 oC 的反应条件下, 该催化剂表现出优异的 FTS 低温活性和较高的稳定性, 反应后产物和催化体系很容易实现分离.     

焙烧温度对铁基催化剂催化浆态床F-T合成反应性能的影响

 采用连续共沉淀与喷雾干燥成型技术相结合的方法制备了微球形Fe-Cu-K-SiO2催化剂,并考察了焙烧温度对催化剂的结构和织构性质的影响. 结果表明,催化剂具有较好的织构和结构热稳定性,粘结剂SiO2起到了分散和稳定α-Fe2O3晶相的作用. 随着焙烧温度的升高,催化剂的比表面积逐渐减小,α-Fe2O3晶粒逐渐增大,催化剂体相中的Cu和K原子向表面富集,且Cu向表面的迁移更明显; 同时,催化剂中的α-Fe2O3和CuO相发生了一定程度的离析,Cu的助剂作用减弱,使催化剂在合成气气氛下难于还原碳化. 催化剂在n(H2)/n(CO)=0.67,GHSV=2.0 L/(g·h),p=1.5 MPa和θ=250 ℃下的浆态床F-T合成反应评价结果表明,升高焙烧温度,催化剂的初活性和最高活性下降,但运行稳定性提高,而且有效地抑制了CH4的生成,明显促进了烃产物向高碳数方向移动. 反应600 h后卸载下的催化剂的形貌观测表明,催化剂的磨损主要是由化学磨损引起的,提高焙烧温度可明显改善其抗磨损性能,焙烧温度高于400 ℃时,催化剂具有较好的抗磨损性能.     

Mn助剂加入方式对铁基催化剂F-T合成性能的影响

采用连续共沉淀与喷雾干燥成型技术相结合的方法制备了系列微球状Fe/Mn/K催化剂,结合H2 DTG、CO TPR、Mossbauer谱等表征手段,研究了Mn助剂的加入方式对铁基催化剂物相结构、还原和碳化行为以及F-T合成性能的影响。催化剂在浆态床反应器中以接近F-T合成实际工况条件 (250℃、1.5MPa、H2/CO=0.67和2.0L /(gcat·h)) 进行评价。结果表明,以共沉淀方式加入Mn助剂具有较强的Fe Mn相互作用,从而抑制了催化剂的还原和碳化,降低了催化剂的活性,提高了催化剂的稳定性。而以部分共沉淀和黏结剂方式加入Mn助剂促进了催化剂的还原和碳化,提高了反应活性加速了催化剂的失活。与共沉淀Mn相比,部分共沉淀和黏结剂Mn提高了重质烃和烯烃的选择性,同时抑制了有机含氧化合物的生成。     

结构助剂SiO2、Al2O3对铁基催化剂浆态床F-T合成性能的影响

采用连续共沉淀与喷雾干燥成型技术相结合的方法制备了微球状Fe/Cu/K/SiO2和Fe/Cu/K/Al2O3催化剂,研究SiO2和Al2O3作为结构助剂对铁基催化剂吸附行为、炭化行为及F-T合成反应性能的影响。表征结果表明,与Al2O3相比较,SiO2抑制了H2的吸附,但促进了CO的吸附,有利于催化剂的炭化。催化剂在260℃、1.5MPa、H2/CO=0.67和2000h-1下的浆态床F-T合成反应评价表明,Fe/Cu/K/SiO2催化剂具有较高的F-T合成活性、高的水煤气变换反应（WGS）活性,且其烃产物选择性明显向高炭数方向偏移,而Fe/Cu/K/Al2O3催化剂则表现出较低的F-T合成活性、低的水煤气变换反应（WGS）活性和高的轻质烃选择性。但Fe/Cu/K/Al2O3催化剂比Fe/Cu/K/SiO2催化剂具有更好的运行稳定性。     

聚乙二醇介质对浆态床合成气制乙醇催化性能的影响

采用不同分子量的聚乙二醇(400、600、800和1 000)作为浆态床反应介质,工业甲醇合成催化剂C302作为催化剂进行一氧化碳加氢反应,运用XRD、H_2-TPR、NH_3-TPD-MS、BET、XPS等方法对催化剂进行表征,考察催化剂C302在不同浆态床反应介质中进行一氧化碳加氢反应后其结构及性能的变化.结果表明浆态床反应介质对催化剂性能的发挥具有显著的影响,以聚乙二醇作为浆态床反应介质,C302用于一氧化碳加氢反应时产物中均出现了乙醇,同时催化剂表现出良好的稳定性.其中以聚乙二醇600作为浆态床反应介质时,反应后催化剂C302中Cu晶粒尺寸降低,存在两种形态的Cu2O且两者数量匹配,同时其弱酸中心增多,表面Zn富集,这些为催化剂高选择性合成乙醇提供了适宜结构,活性评价显示乙醇选择性达到25.21%.     

浆态反应器中铁／活性炭催化剂上还原研究

众所周知，费托合成（Fischer-Tropsch synthesis,FTS)反应是一个有理论与应用价值的研究课题。数十年来，学者们已发现了铁系，钴系和钌系等具有优良FTS反应性能的催化剂体系，铁／活性炭（Fe/Activated Carbon,AC)催化剂是中国科学院大连化学物理研究所八十年代末开发的一类费托合成催化剂，由于活性炭载体发达的孔结构使得该催化剂上FTS反应产物中汽油，柴油选择性高（烃类碳数小于20）和油收率大（C5^ ,112g/m^3 sysgaa)^[1,2]，具有工业放大前景。本文采用1L浆态床反应器，应用不同的还原方法（原位高压还原和反应器外还原）和XRD物相表征手段，了铁／活性炭催化剂在浆态床中的还原与反应问题，得到了一些有用的信息。     

CuO的添加方式对合成二甲醚反应中脱水性能的影响

CuO以不同的添加方式对-γA l2O3进行改性.用H2-TPR、还原态NH3-TPD、XRD表征技术以及浆态床CO H2合成二甲醚反应对催化剂的还原性能、还原态的酸中心分布、物相分布和反应活性进行了考察.H2-TPR结果表明,在沉积法制备的催化剂上可还原的氧化铜的量最大,且容易还原;还原态NH3-TPD结果说明了沉积法制备的催化剂上适合脱水反应进行的弱酸中心的比例最大;XRD结果发现在浸渍法制备的催化剂上,有少量的铜和铜铝化合物存在,其它方法制备的催化剂上CuO均匀分散在催化剂表面;目标反应的结果指出了沉积法制备的催化剂上,二甲醚的选择性最佳.     

浆态床合成二甲醚复合催化剂失活原因探索

在反应温度260 ℃、压力5.0 MPa的条件下,对浆态床反应器中二甲醚合成复合催化剂的失活规律进行了研究.结果表明,Cu基催化剂失活较快是导致浆态床二甲醚合成催化剂不稳定的主要原因.通过分析Cu基催化剂在浆态床反应器和固定床反应器中的活性变化规律,发现在浆态床反应器中不能及时导出反应体系的H2O对催化剂的毒副作用导致了浆态床Cu基催化剂快速失活.对失活催化剂进行的TPR、XRD和SEM-EDS表征结果可以看出,Cu粒子的长大和积炭是Cu基催化剂失活的重要原因,与已有文献报道不同的是并未发现明显的Cu元素流失.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。