Layer-by-layer deposited multilayer films of oligo(pyrenebutyric acid) and a perylene diimide derivative: structure and photovoltaic properties

Multilayer films of oligo(pyrenebutyric acid) (OPB) and N,N'-bis(N,N-dimethylaminopropylaminopropyl)-3,4,9,10-perylenediimide (BDMAPAP-PDI) were successfully fabricated by layer-by-layer deposition. Multilayer growth was monitored by ultraviolet-visible (UV-vis) spectroscopy, fluorescence spectroscopy, ellipsometry, and atomic force microscopy (AFM). It was found that extraction was scarcely observed although both components (OPB and BDMAPAP-PDI) have low molecular weights and both electrostatic interactions and pi-pi stacking contributed to the multilayer deposition. The multilayers exhibit a rapid photocurrent response, and excitations of both OPB and BDMAPAP-PDI can lead to the effective charge dissociation. The incident photon to current conversion efficiency (IPCE) of the composite film with 5 bilayers was measured to be 1.29% at the absorption peak of BDMAPAP-PDI. Fluorescence quenching and photovoltaic conversion studies indicated that strong photoinduced charge transfer interactions occurred at the area of OPB/BDMAPAP-PDI heterojunction in the films, which strongly enhanced the photoresponse of the multilayer films.     

Layer-by-layer deposition of rhenium-containing hyperbranched polymers and fabrication of photovoltaic cells

Multilayer thin films were prepared by the layer-by-layer (LBL) deposition method using a rhenium-containing hyperbranched polymer and poly[2-(3-thienyl)ethoxy-4-butylsulfonate] (PTEBS). The radii of gyration of the hyperbranched polymer in solutions with different salt concentrations were measured by laser light scattering. A significant decrease in molecular size was observed when sodium trifluoromethanesulfonate was used as the electrolyte. The conditions of preparing the multilayer thin films by LBL deposition were studied. The growth of the multilayer films was monitored by absorption spectroscopy and spectroscopic ellipsometry, and the surface morphologies of the resulting films were studied by atomic force microscopy. When the pH of a PTEBS solution was kept at 6 and in the presence of salt, polymer films with maximum thickness were obtained. The multilayer films were also fabricated into photovoltaic cells and their photocurrent responses were measured upon irradiation with simulated air mass (AM) 1.5 solar light. The open-circuit voltage, short-circuit current, fill factor, and power conversion efficiency of the devices were 1.2 V, 27.1 mu A cm(-2), 0.19, and 6.1x10(-3) %, respectively. The high open-circuit voltage was attributed to the difference in the HOMO level of the PTEBS donor and the LUMO level of the hyperbranched polymer acceptor. A plot of incident photon-to-electron conversion efficiency versus wavelength also suggests that the PTEBS/hyperbranched polymer junction is involved in the photosensitization process, in which a maximum was observed at approximately 420 nm. The relatively high capacitance, determined from the measured photocurrent rise and decay profiles, can be attributed to the presence of large counter anions in the polymer film.     

Property influence of polyanilines on photovoltaic behaviors of dye-sensitized solar cells

The influence of polyanilines (PANIs) as hole conductors on the photovoltaic behaviors of dye-sensitized solar cells is studied. The current-voltage (I-V) characteristics and the incident photon to current conversion efficiency (IPCE) curves of the devices are determined as the function of different conductivities and morphologies of PANIs. The results show that the conductivity of PANIs affects the performance of the devices greatly, and PANI with the intermediate conductivity value (3.5 S/cm) is optimum. In addition, the effects of both the film formation property and the cluster size of polyanilines on the photovoltaic behaviors of the devices are also discussed.     

Use of a ruthenium-containing conjugated polymer as a photosensitizer in photovoltaic devices fabricated by a layer-by-layer deposition process

Multilayer polymer films composed of a ruthenium terpyridine complex containing poly(p-phenylenevinylene) (Ru-PPV) and sulfonated polyaniline (SPAN) were prepared by a layer-by-layer electrostatic self-assembly deposition. The deposition process was carried out from SPAN solution in water and Ru-PPV in dimethylformamide (DMF). Optical-quality multilayer thin films were obtained. The film growth process was monitored by quartz crystal microbalance, and the surface morphology of the films was studied by atomic force microscopy. It was found that the properties of the multilayer films were dependent on deposition conditions such as the pH of the SPAN solution, the presence of salt in the polymer solutions, and the post-film-forming thermal annealing process. Cross-section transmission electron microscopic images suggested that there was no stratified structure formed in the multilayer films. Photovoltaic cells were fabricated by sandwiching the multilayer films between indium-tin-oxide and aluminum electrodes. The device performances were examined by illumination with AM 1.5 simulated solar light. The power conversion efficiencies of these devices were on the order of 10(-3)%. The maximum incident photon-to-electron conversion efficiency (IPCE) of the devices was found to be approximately 2% at 510 nm, which is consistent with the absorption maximum of the ruthenium complex. This indicates that the photosensitization process is due to the electronic excitation of the ruthenium complex.     

Co-sensitization of organic dyes for efficient ionic liquid electrolyte-based dye-sensitized solar cells

The co-sensitization of two organic dyes (SQ1 and JK2), which are complementary in their spectral responses, shows enhanced photovoltaic performance compared with that of an individual organic dye-sensitized solar cell. The power conversion efficiency of the co-sensitized organic dye solar cell based on the newly developed binary ionic liquid (solvent-free) electrolyte gives 6.4% under AM 1.5 sunlight at 100 mW/cm2 irradiation, which is higher than that of individual dye-sensitized solar cells. The incident monochromatic photon-to-current conversion efficiency (IPCE) of the co-sensitized solar cell shows typical absorption peaks at 530 and 650 nm corresponding to the two dyes and displays a broad spectral response over the entire visible spectrum with IPCE of >40% in the 400-700 nm wavelength domain.     

A swift dye uptake procedure for dye sensitized solar cells

Solar cells based on swift self-assembled sensitizer bis(tetrabutylammonium)-cis-di(thiocyanato)-N,N'-bis(4-carboxylato-4'-carboxylic acid-2,2'-bipyridine)ruthenium(II) (N719) on double layers of 12 + 4 microm thick nanocrystalline TiO2 films exhibit the incident monochromatic photon-to-current conversion efficiency (IPCE) 90% and show a short circuit current density of 17 mA cm(-2), 750 mV open circuit potential and 0.72 fill factor yielding power conversion efficiencies over 9.18% under AM 1.5 sun. For the first time highest power conversion efficiencies are obtained for dye sensitized solar cells using a swift self-assembled procedure.     

Near-IR light-sensitized voltaic conversion system using nanocrystalline TiO2 film by Zn chlorophyll derivative aggregate

A Zn chlorophyll-a derivative, Zn chlorin-e6 (ZnChl-e6), adsorbed onto a nanocrystalline TiO2 film (ZnChl-e6/TiO2) electrode was prepared, and the photovoltaic properties of the ZnChl-e6/TiO2 electrode were studied. The absorption peaks of ZnChl-e6/TiO2 observed at 420, 654, and 795 nm were attributed to the ZnChl-e6 molecules aggregating onto TiO2 film. The fluorescence attributed to the ZnChl-e6 monomer and aggregate was observed at 710 and 820 nm, respectively, and the fluorescence in both cases was quenched by TiO2 particles. The maximum of the incident photon-to-current conversion efficiency (IPCE) value in the photocurrent action spectrum was 800 nm, and the IPCE value was 7.0%. ZnChl-e6 molecules formed aggregates on a nanocrystalline TiO2 film electrode. From the photocurrent-photovoltage characteristics of the ZnChl-e6/TiO2 electrode irradiated with 100 mW cm(-2), the short-circuit photocurrent (I(SC)) was found to be 0.19 mA cm(-2) and the open-circuit photovoltage (V(OC)) was found to be 375 mV. The maximum power was estimated to be 28.7 microW cm(-2), and the fill factor (FF) was estimated to be 40.1%. A near-IR light induced photovoltaic conversion system using a ZnChl-e6 aggregate formed onto a nanocrystalline TiO2 film electrode was achieved.     

Mechanisms and applications of plasmon-induced charge separation at TiO2 films loaded with gold nanoparticles

Plasmon-induced photoelectrochemistry in the visible region was studied at gold nanoparticle-nanoporous TiO(2) composites (Au-TiO(2)) prepared by photocatalytic deposition of gold in a porous TiO(2) film. Photoaction spectra for both the open-circuit potential and short-circuit current were in good agreement with the absorption spectrum of the gold nanoparticles in the TiO(2) film. The gold nanoparticles are photoexcited due to plasmon resonance, and charge separation is accomplished by the transfer of photoexcited electrons from the gold particle to the TiO(2) conduction band and the simultaneous transfer of compensative electrons from a donor in the solution to the gold particle. Besides its low-cost and facile preparation, a photovoltaic cell with the optimized electron mediator (Fe(2+/3+)) exhibits an optimum incident photon to current conversion efficiency (IPCE) of 26%. The Au-TiO(2) can photocatalytically oxidize ethanol and methanol at the expense of oxygen reduction under visible light; it is potentially applicable to a new class of photocatalysts and photovoltaic fuel cells.     

Novel carboxylated oligothiophenes as sensitizers in photoelectric conversion systems

Novel carboxylated oligothiophenes with different thiophene units were designed and synthesized as photosensitizers in dye-sensitized solar cells (DSSCs) for efficient opto-electric materials. The introduction of -COOH into thiophene molecules can lead to a red shift of UV-visible absorption, increase light-harvesting efficiency, and enhance photoinduced charge transport by forming efficient covalent bonds to the substrate surface. A red shift of the absorption spectrum of oligothiophene is also achieved by the increase in the number of thiophene units. The DSSCs based on the oligomers have excellent photovoltaic performances. Under 100 mW cm(-2) irradiation a short-circuit current of 10.57 mA cm(-2) and an overall energy conversion efficiency of 3.36 % is achieved when pentathiophene dicarboxylated acid was used as a sensitizer. The incident photo-to-current conversion efficiency (IPCE) has a maximum as high as 80 %. In addition, photovoltage and photocurrent transients show that slow charge recombination in DSSCs is important for efficient charge separation and excellent photoelectric conversion properties of the oligomers. These initial and promising results suggest that carboxylated oligothiophenes are efficient photosensitizers.     

Self-assembly and photoelectric properties of cerium complexes with 3,4,9,10-perylenetetracarboxylic acid on nanocrystalline TiO_2 films

Self-assembled (SA) films (PMP, M = Ce3+ or Ce4+) of 3,4,9,10-perylenetetracarboxylic acid (PTA) on nanocrystalline TiO2 films with Ce3+ or Ce4+ as a bridge were fabricated and characterized with UV-Vis, IR, and XPS synchrotron radiation photoelectron spectroscopy (SRPES) which gave the HOMO energy levels for the SA films. It was shown that thin-layer sandwich-type solar cells based on these SA films possess good properties for photoelectric conversion. While PTA-loaded TiO2 electrode (P) generated 26.9% of incident monochromatic photon-to-electron conversion efficiency (IPCE), PMP-sensitized Ti02 electrodes yielded 55.8% and 39.1% for Ce4+ and Ce3+ respectively. PMP films can be considered as a kind of complexes whose HOMO energy levels were proved to be higher than that of film P, which is one of the major reasons for the increase in IPCE from film P to film PMP.     

Benzothiadiazole Containing D‐π‐A Conjugated Compounds for Dye‐Sensitized Solar Cells: Synthesis,Properties, and Photovoltaic Performances

Two D ‐π‐A conjugated molecules, BzTCA and BzTMCA , were developed through facile synthetic approaches for dye‐sensitized solar cells. The investigation of the photophysical properties of BzTCA and BzTMCA both in dilute solutions and in thin films indicates that their absorption exhibits a wide coverage of the solar spectrum. The absorption features for BzTCA and BzTMCA commence at about 710 nm in solution, and at about 800 nm in the solid state. The absorption maxima (λ_max) for both BzTCA and BzTMCA on TiO₂ film are almost the same as those in dilute solution. Their HOMOs and LUMOs were found to partly overlap at the center of these dyes, which guarantees appreciable interactions between the donors and acceptors. The investigation of the performance of dye‐sensitized solar cells fabricated from BzTCA and BzTMCA indicated that the power‐conversion efficiencies are 6.04 % and 4.68 %, respectively, which could be comparable with the normal sensitizer N3. BzTMCA showed lower incident photon‐to‐electron conversion efficiency (IPCE) and J_sc values relative to BzTCA , which is probably because of the weaker driving force of dye regeneration and electron injection process of BzTMCA . The IPCE responsive area reached nearly 800 nm, which provides great potential for further improvement of the photocurrent density and power‐conversion efficiency. Our investigations demonstrate that both dyes BzTCA and BzTMCA could be promising candidates for dye‐sensitized solar cells.     

Extending the photoresponse of TiO2 to the visible light region: photoelectrochemical behavior of TiO2 thin films prepared by the radio frequency magnetron sputtering deposition method

TiO(2) thin films prepared by a radio frequency magnetron sputtering (RF-MS) deposition method were found to show an enhanced photoelectrochemical response in the visible light region. By controlling the temperature and the gaseous medium during the deposition step, it was possible to control the properties of these films. The photoelectrochemical behavior of the sputtered TiO(2) thin films was compared with that of a commercial TiO(2) sample, and the sputtered films showed higher incident photon to the charge carrier generation efficiency (IPCE of 12.6% at 350 nm) as well as power conversion efficiency (0.33% at 1.84 mW/cm(2)) than the commercial TiO(2) sample. Femtosecond transient absorption spectroscopy experiments have revealed that a major fraction of photogenerated electrons and holes recombine within a few picoseconds, thus limiting photocurrent generation efficiency. The mechanistic insights obtained in the present study should aid in designing semiconductor nanostructures that will maximize the charge separation efficiency and extend the response of the large band gap semiconductor TiO(2) into visible light regions.     

Facile and efficient approach to speed up layer-by-layer assembly: dipping in agitated solutions

A facile and efficient approach has been developed to speed up the fabrication of LBL films through sequential dipping in vigorously agitated solutions. By this agitated-dipping (AD) LBL technique, the multilayer films of PAH and PSS were fabricated. The resulting films were explored by UV-vis spectroscopy, X-ray reflectivity, and AFM. Meanwhile, the comparison of the AD and conventional LBL films was made, which demonstrated that AD LBL can decrease dipping time by more than 15 times without reducing film quality remarkably. In addition, to verify the generality of AD LBL, we studied the AD LBL films of PDDA/PSS and PAH/PAA preliminarily as well. AD LBL promotes the efficiency of conventional LBL greatly while preserving its most advantages, such as simplicity, cheapness, precise control, universality in substrates, recycling use of sample solutions, and so on. It would be a promising alternative to build up LBL films rapidly.     

A simple recipe for an efficient TiO2 nanofiber-based dye-sensitized solar cell

Development of highly efficient dye-sensitized solar cells (DSSCs) with good photovoltaic parameters is an active research area of current global interest. In this article, we provide a simple recipe for the fabrication of electrospun TiO(2) nanorod-based efficient dye-sensitized solar cell using a Pechini-type sol. The Pechini-type sol of TiO(2) nanofibers produces a highly porous and compact layer of TiO(2) upon doctor-blading and sintering without the need for an adhesion and scattering layers or TiCl(4) treatment. The best nanofiber DSSCs with an area of ~0.28 cm(2) shows an efficiency of ~4.2% under standard test conditions (100 mW/cm(2), 25°C and AM1.5 G) and an incident photon-to-electron conversion efficiency (IPCE) of ~50%. Impedance measurements show lower charge transfer resistance that improved the fill factor. We believe that simple approaches such as the present one to develop nanofiber DSSCs would open up enormous possibilities in effective harvesting of solar energy for commercial applications, considering the fact that electrospinning is a cost-effective method for the mass scale production of nanofibers and nanorods.     

Self-assembly and photoelectric properties of cerium complexes with 3, 4, 9, 10-perylenetetracarboxylic acid on nanocrystalline TiO2 films

Self-assembled (SA) films (PMP, M = Ce³⁺ or Ce⁴⁺) of 3,4,9,10-perylenetetracarboxylic acid (PTA) on nanocrystalline TiO₂ films with Ce³⁺ or Ce⁴⁺ as a bridge were fabricated and characterized with UV-Vis, IR, and XPS synchrotron radiation photoelectron spectroscopy (SRPES) which gave the HOMO energy levels for the SA films. It was shown that thin-layer sandwich-type solar cells based on these SA films possess good properties for photoelectric conversion. While PTA-loaded TiO₂ electrode (P) generated 26.9% of incident monochromatic photon-to-electron conversion efficiency (IPCE), PMP-sensitized TiO₂ electrodes yielded 55.8% and 39.1% for Ce⁴⁺ and Ce³⁺ respectively. PMP films can be considered as a kind of complexes whose HOMO energy levels were proved to be higher than that of film P, which is one of the major reasons for the increase in IPCE from film P to film PMP.     

New Bithiazole‐Based Sensitizers for Efficient and Stable Dye‐Sensitized Solar Cells

A series of new push–pull organic dyes ( BT‐I – VI ), incorporating electron‐withdrawing bithiazole with a thiophene, furan, benzene, or cyano moiety, as π spacer have been synthesized, characterized, and used as the sensitizers for dye‐sensitized solar cells (DSSCs). In comparison with the model compound T1 , these dyes containing a thiophene moiety between triphenylamine and bithiazole display enhanced spectral responses in the red portion of the solar spectrum. Electrochemical measurement data indicate that the HOMO and LUMO energy levels can be tuned by introducing different π spacers between the bithiazole moiety and cyanoacrylic acid acceptor. The incorporation of bithiazole substituted with two hexyl groups is highly beneficial to prevent close π–π aggregation, thus favorably suppressing charge recombination and intermolecular interaction. The overall conversion efficiencies of DSSCs based on bithiazole dyes are in the range of 3.58 to 7.51 %, in which BT‐I ‐based DSSCs showed the best photovoltaic performance: a maximum monochromatic incident photon‐to‐current conversion efficiency (IPCE) of 81.1 %, a short‐circuit photocurrent density (J_sc) of 15.69 mA cm^?2, an open‐circuit photovoltage (V_oc) of 778 mV, and a fill factor (ff) of 0.61, which correspond to an overall conversion efficiency of 7.51 % under standard global AM 1.5 solar light conditions. Most importantly, long‐term stability of the BT‐I – III ‐based DSSCs with ionic‐liquid electrolytes under 1000 h of light soaking was demonstrated and BT‐II with a furan moiety exhibited better photovoltaic performance of up to 5.75 % power conversion efficiency.     

Influence of a TiCl4 post-treatment on nanocrystalline TiO2 films in dye-sensitized solar cells

In this study, the influence of the TiCl(4) post-treatment on nanocrystalline TiO(2) films as electrodes in dye-sensitized solar cells is investigated and compared to nontreated films. As a result of this post-treatment cell efficiencies are improved, due to higher photocurrents. On a microscopic scale TiO(2) particle growth on the order of 1 nm is observed. Despite a corresponding decrease of BET surface area, more dye is adsorbed onto the oxide surface. Although it seems trivial to match this finding with the improved photocurrent, this performance improvement cannot be attributed to higher dye adsorption only. This follows from comparison between incident photon to current conversion efficiency (IPCE) and light absorption characteristics. Since the charge transport properties of the TiO(2) films are already more than sufficient without treatment, the increase in short circuit current density J(SC) cannot be related to improvements in charge transport either. Transient photocurrent measurements indicate a shift in the conduction band edge of the TiO(2) upon TiCl(4) treatment. It is concluded that the main contribution to enhanced current originates from this shift in conduction band edge, resulting in improved charge injection into the TiO(2).     

聚3-甲基噻吩修饰硫化物量子点连接纳米结构TiO2膜的光电化学研究

采用原位化学法在纳米结构TiO₂膜上制备了量子点CdS, PbS (Q-CdS, Q-PbS), 并用电化学方法在TiO₂/Q-CdS, TiO₂/Q-PbS表面聚合3-甲基噻吩[poly(3-Methylthiophene, PMeT)]. 用光电化学方法研究了PMeT修饰Q-CdS, Q-PbS连接TiO₂纳米结构膜, 实验结果表明, PMeT和Q-CdS, Q-PbS单独修饰纳米结构TiO₂电极和PMeT修饰Q-CdS, Q-PbS连接纳米结构TiO₂电极的光电流产生的起始波长都向长波方向移动; 一定条件下在可见光区光电转换效率均较纳米结构TiO₂的光电转换效率有明显的提高; 聚3-甲基噻吩(PMeT)与Q-CdS, Q-PbS连接的纳米结构TiO₂之间存在p-n异质结. 在一定条件下p-n异质结的存在有利于光生电子/空穴的分离, 在本文实验条件下PMeT修饰Q-CdS, Q-PbS连接纳米结构TiO₂电极最高的单色光的光电转换效率分别为11%和7%.     

Effects of spin-coating speed on the morphology and photovoltaic performance of the diketopyrrolopyrrole-based terpolymer

Polymer solar cells（PSCs） were fabricated by combining a diketopyrrolopyrrole-based terpolymer（PTBT-HTID-DPP） as the electron donor, and [6,6]-phenyl C₆₁ butyric acid methyl ester(PC₆₁BM) as the electron acceptor, and the power conversion efficiency（PCE） of 4.31% has been achieved under AM 1.5 G(100 m W cm^-2) illumination condition via optimizing the polymer/PC₆₁BM ratio, the variety of solvent and the spin-coating speed. The impact of the spin-coating speed on the photovoltaic performance of the PSCs has been investigated by revealing the effects of the spin-coating speed on the morphology and the absorption spectra of the polymer/PC₆₁BM blend films. When the thickness of the blend films are adjusted by spin-coating a fixed concentration with different spin-coating speeds, the blend film prepared at a lower spin-coating speed shows a stronger absorption per unit thickness, and the correspond device shows higher IPCE value in the longer-wavelength region. Under the conditions of similar thickness, the blend film prepared at a lower spin-coating speed forms a more uniform microphase separation and smaller domain size which leads to a higher absorption intensity per unit thickness of the blend film in long wavenumber band, a larger short-circuit current density(J_sc) and a higher power conversion efficiency（PCE） of the PSC device. Noteworthily, it was found that spin-coating speed is not only a way to control the thickness of active layer but also an influencing factor on morphology and photovoltaic performance for the diketopyrrolopyrrole-based terpolymer.     

方酸染料在远红光区／近红外区对纳米晶二氧化钛电极的高效敏化作用

Four para-dialkylaminophenyl （PDAAP1-PDAAP4） bearing carboxyl groups were studied for application to the dye-sensitized solar cells （DSC）. It was found the short spacer CH2 between carboxyl and dialkylaminophenyl chromophore in PDAAP3 and PDAAP4 led to highly efficient monochromatic incident photon-to-current conversion efficiencies （IPCE）, however the long alkyl group C4H9 attached on aniline moieties in PDAAP2 and PDAAP4 favored improvement of open-circuit photovoltage. Thus, the solar cell sensitized by PDAAP4, having both short carboxyl groups CH2COOH and long alkyl groups C4H9, exhibited the IPCE maximum of 73% at 670 nm and overall energy conversion efficiency η of 3.06%, representing the highest IPCE and η values so far in dialkylaminophenyl-based organic dye-sensitized semiconductor solar cells. Taking advantage of the highly efficient sensitizing ability of PDAAP4 in far-red region, the data of IPCE above 630 nm of the solar cells were improved greatly by cosensitization with both N3 and PDAAP4. The influences of the TiO2 film thickness and the concentration of 4-tert-butylpyridine （TBP） in electrolyte were also investigated.