Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

Zr0.5Ti0.5O2的添加对超临界裂解RP-3催化剂性能的影响

采用共沉淀法制备了Zr_0.5Ti_0.5O₂载体材料,将其掺杂在CeO₂-Al₂O₃ (CA)基催化剂中, 并对其催化活性进行了超临界裂解测试, 采用全自动吸附仪、X射线衍射(XRD)、透射电镜(TEM)、程序升温脱附(TPD)等方法对催化剂进行了表征. 实验结果表明, 催化剂能够明显降低裂解反应的温度, 600 ℃ CA基催化剂产气率是热裂解的2.8倍, 掺杂Zr_0.5Ti_0.5O₂载体材料的CA基催化剂是热裂解的4.0倍, 650 ℃时, 掺杂Zr_0.5Ti_0.5O₂载体材料的CA基催化剂热沉提高了0.55 MJ·kg^-1. BET结果表明, 掺杂Zr_0.5Ti_0.5O₂载体后催化剂出现双孔结构, 部分小孔的出现使得乙烯的选择性提高; NH₃-TPD结果表明, 掺杂Zr_0.5Ti_0.5O₂载体材料后, 催化剂强酸位的酸量增加了4.0倍,催化剂表现出更强的表面酸性和更集中的强酸酸中心密度, 有利于裂解多产烯烃.     

具有双孔径分布的介孔C-Al2O3-TiO2纳米复合材料的合成及其红外发射率

以嵌段共聚物F127 (PEO₁₀₆PPO₇₀PEO₁₀₆, M_W=12600)为模板剂, 异丙醇铝和钛酸四丁酯为金属源, 低分子量的酚醛树脂为碳源, 通过溶胶-凝胶三元共组装法合成了具有双孔径分布的C-Al₂O₃-TiO₂纳米复合材料.用X射线衍射(XRD)、透射电子显微镜(TEM)、扫描电子显微镜(SEM)及N₂吸附-脱附对该复合材料进行结构表征. 结果显示, 当铝钛原子的摩尔比为1:10 时, 对应的纳米复合材料具有较好的有序介孔结构, 其双孔径分别为3.9和6.5 nm, 比表面积可达259 m²·g^-1, 孔容0.37 cm³·g^-1. 以三元乙丙橡胶(EPDM)为粘结剂, 与介孔纳米复合材料混合制备涂层. 通过调节复合材料中铝钛摩尔比和涂层厚度, 红外发射率在0.450-0.617之间可调.     

乙烯在纳米催化剂InVO4-TiO2上的可见光降解

The InVO₄-TiO₂ nano-crystalline photocatalyst was prepared by sol-gel method and characterized by DRS, FTIR, Raman and XRD. The photocatalytic activities of the prepared sample were investigated by photocatalytic degradation of ethylene in the gaseous phase under visible light irradiation (λ>450 nm). The results indicate that both of pure TiO₂ and InVO₄ or their simple mixture show no photocatalytic activities for degradation of ethylene under visible light irradiation. However, as-synthesized InVO₄-TiO₂ catalyzes the degradation of ethylene into CO₂ under visible light irradiation. In addition, the interaction between InVO₄ and TiO₂ results in some structural distortion to all the crystal forms of TiO₂ in as-synthesized catalyst InVO₄-TiO₂.     

SiO2-TiO2 membranes by the sol-gel process

The use of membranes for gas separation represents an important alternative from the viewpoint of energy conservation in industrial separation processes. Polymeric Si-Ti sols prepared from titanium isopropoxide (Ti(OPrⁱ)₄) and tetraethoxysilane (TEOS) were used to deposit membranes on α-Al₂O₃ supports. Acetylacetone (2,4 pentanedione, acacH) and isoeugenol (2-methoxy-4-propenylphenol, isoH) were employed separately to chelate the Ti precursor in order to slow down the chemical reactivity, avoiding precipitation. The radial distribution functions (RDF) of the gels aging at room temperature were obtained. The xerogels were studied by Thermal Gravimetric (TGA) and Differential Thermal (DTA) Analysis in air. The Microporosity of the solids calcined at 773 K was determined by N₂-adsorption at 77 K. The membrane thickness was determined from SEM photographs. Preliminary permeance results of the supported membranes on commercial alumina support were obtained for He, N₂ and CO₂ in a single gas equipment. At 773 K the separation factors α(He/CO₂) and α(N₂/CO₂) for both membranes exceeds the theoretical Knudsen limit.     

Pt/SrZr0.95Y0.05O3-TiO2-xNx复合催化剂的制备及模拟太阳光催化产氢活性研究

利用共沉淀法和固相法制备出SrZr_0.95Y_0.05O₃微粒,采用溶胶包覆法使其与含氮TiO₂溶胶复合,并原位光沉积Pt颗粒组装成异质结复合催化剂,采用XRD、TG-DTA、紫外可见漫反射光谱(UV-Vis DRS)和荧光光谱(FS)等技术对其进行了表征和分析,以草酸为牺牲剂,模拟太阳光下光催化产氢为探针,评价了催化剂的光催化活性。研究了不同氮源剂、烧结温度、载铂含量对催化剂光催化产氢活性的影响。结果表明,在模拟太阳光照射下,单独的SrZr_0.95Y_0.05O₃和TiO₂几乎不产生氢气;而将两者采用溶胶包覆法复合并掺氮后,所制备出的复合催化剂表现出一定程度的产氢活性,在氮源剂为三乙胺、400 ℃焙烧下具有最佳的产氢活性,催化活性的提高源于复合催化剂中形成的异质结抑制了光生载流子的快速复合以及氮掺杂引起对可见光的响应;进一步负载铂后,其产氢量得到大幅度的提高,其最佳负载量为1wt%,6 h内产氢量达到12.5 mmol,是未负载的样品的22倍多,这是由于铂负载进一步抑制了光生载流子的复合,从而大大地提高了光催化活性。     

Formation and Crystallization Behavior of Gels in the Na2O-SiO2-TiO2-ZrO2 System

SiO₂-TiO₂-ZrO₂ and 5Na₂O·95(SiO₂ + TiO₂ + ZrO₂) gels were synthesized and role of Na₂O in gel formation and crystallization behavior of gels were studied. From Si(OC₂H₅)₄, Ti(iso-OC₃H₇)₄, Zr(n-OC₃H₇)₄ and NaOCH₃ solutions in EtOH without H₂O, transparent and opaque gels were obtained. Opaque bulk gels, rich in TiO₂ or ZrO₂ composition in Na₂O containing SiO₂-TiO₂-ZrO₂ system, contain agglomerated spherical particles of diameter small <10 m, in contrast with opaque gels having large particles <30 m in alkali-free SiO₂-TiO₂-ZrO₂ system. Crystallization temperature (Tc) was measured by DTA on dried gels. Compared with the alkali-free SiO₂-TiO₂-ZrO₂ gels, 5 mol% Na₂O containing gels gave lower Tc in SiO₂ rich compositions and higher in TiO₂ rich or ZrO₂ rich compositions.     

Characterization of an all Sol-Gel Electrochromic Device WO3/Ormolyte/CeO2-TiO2

Electrochemical lithium intercalation in thin films of CeO₂-TiO₂ and WO₃, prepared by the sol-gel technique was investigated with cyclic voltammetry and spectroelectrochemical techniques in propylene carbonate solutions. A solid state system having the configuration WO₃/Ormolyte/CeO₂-TiO₂ has been assembled. The solid electrolyte, an organically modified electrolyte (ormolyte), was prepared with different [O]/[Li] ratios. The transmittance variation of this system during a potentiostatic step from –0.7 V to 0.8 V was about 35% at 550 nm.     

Proton Affinity at the Porous Surface of SiO2-TiO2 Binary Oxides

SiO₂-TiO₂ binary oxides are typically used as solid supports for different applications, from catalysts to optics. Tailoring the pore diameter, pore size distribution, and surface area is of great importance for any of those applications. Tailoring the chemical properties of the porous surface, e.g. in terms of polarity or acidity, is of capital importance as well. Thus, in catalytic applications or in sensing devices, where diffusion of a solute through the matrix is required, the affinity/compatibility of the solute with the matrix porous surface will determine the proper work of the device. Moreover, when the sensor is based on the adsorption of an active organic molecule or biomolecule on the porous surface matrix, the proton concentration at the surface may also modify the behavior of the active molecule. In this work, the proton affinity of the porous surface is tailored by the preparation of number of SiO₂-TiO₂ binary oxides with different SiO₂/TiO₂ weight ratios. Proton affinity is studied through the incorporation of a pH indicator as bromocresol green.     

磁靶向纳米Fe3O4-TiO2复合物的制备及其对肝癌细胞的光催化杀伤效应

采用三种低温溶胶-凝胶法制备了具有不同Fe₃O₄掺杂量的磁靶向纳米Fe₃O₄-TiO₂复合物, 通过X射线衍射(XRD)、透射电镜(TEM)、傅里叶变换红外(FTIR)光谱、紫外-可见(UV-Vis)光谱、荧光光谱(FS)及磁性能分析等表征方法筛选出包覆均匀、分散性好、磁性能优异及光催化活性较高的纳米Fe₃O₄-TiO₂复合物. 以四甲基偶氮唑蓝(MTT)法检测肝癌细胞(HepG2)的存活率, 考察纳米Fe₃O₄-TiO₂复合物在外磁场作用下对HepG2 细胞的光催化杀伤效应. 结果表明: 采用方法三制备的5%(质量分数)Fe₃O₄-TiO₂复合物具备核-壳结构, 在混悬液中分散性较好, 平均粒径约为50 nm, 具有较强的光催化活性和良好的磁响应性, 同时将纳米TiO₂的光响应范围拓宽至444 nm; 在外磁场作用下, 紫外光和可见光激发纳米Fe₃O₄-TiO₂复合物对HepG2细胞的杀伤效应差异不大, 且均强于纳米TiO₂; 其杀伤效应在0-1.0 T范围内随着外磁场强度的增大而增强.     

Thermally activated and non-activated charge transport processes in the oxides NaxMo2

The electrical properties of Na_xM_1+yO₂ (M=Mn,Co) were measured as a function of temperature under conditions of thermodynamic equilibrium for a quenched defect structure. The results of electrochemical studies of Na_xM_1+yO₂ are also presented. A correlation is demonstrated between the structures of the ionic and electronic defects in these materials and the potential changes of the cathode in Na/Na⁺/Na_xM_1+yO₂.The author is grateful to Prof. S. Mrowec and Dr. A. Stoklosa for helpful discussions.     

三维有序大孔Ag/ZrO2-TiO2：制备及紫外光催化降解染料和水杨酸性能

采用聚苯乙烯(PS)微球作为模板剂,经溶胶-凝胶及煅烧后处理的方法制备了三维有序大孔(3DOM)复合材料Ag/ZrO2-TiO2。通过FTIR、XRD、XPS、N2吸附-脱附和SEM-EDS等对其进行了表征。结果显示,经PS微球作用后的复合材料Ag/ZrO2-TiO2具有锐钛矿晶型结构,其Ag以单质形式存在。该复合材料的孔结构高度有序,属三维有序大孔,平均孔直径为120 nm,孔壁由紧密堆积的Ag/ZrO2-TiO2纳米晶粒组成,孔收缩率约为40%。该复合材料表现出较好的紫外光催化降解水杨酸和甲基橙等染料性能,其活性明显高于商用光催化剂(Degussa P-25)、Ag/ZrO2-TiO2和3DOM ZrO2-TiO2,在90 min内对甲基橙的降解率达80.1%。     

Effect of La2O3 on Catalytic Performance of Au/TiO2 for CO Oxidation

Pure TiO₂ and La-doped TiO₂ were prepared by the sol-gel method. Au was supported on TiO₂ by the deposition-precipitation (DP) method, and its catalytic activity for CO oxidation was tested. The results showed that doping La in Au/TiO₂ could improve its catalytic activity obviously for CO oxidation. The analyses of X-ray diffraction (XRD), temperature-programmed desorption (TPD), and Brunauer-Emmett-Teller (BET) surface area further showed that the presence of La in TiO₂ not only increased its surface area and restrained the growth of TiO₂ crystallites, but could also enhance the microstrain of TiO₂. In terms of O₂-TPD, a new adsorbed species O⁻ appeared on the surface of La-doped TiO₂. The results of in-situ Fourier transform-infrared (FT-IR) spectroscopy illustrated that the high activity of Au/La₂O₃-TiO₂ was attributed to the presence of La promoting the reactivity of CO adsorbed on the Au site and the formation of the second active site on the surface of TiO₂     

α-Fe2O3掺杂对In2O3电导和气敏性能的影响

用化学共沉淀法制备了α Fe2O3掺杂的In2O3纳米晶微粉,研究了α Fe2O3掺杂对In2O3电导和气敏性能的影响. 结果表明, α Fe2O3和In2O3间可形成有限固溶体In2－xFexO3(0≤x≤0.40); Fe3＋对In2O3晶格中In3＋格位的部分取代,大大增强了阴阳离子间的结合力,导致材料中氧空位VO×数骤降、 自由电子的浓度变稀和电导下降. n(Fe3＋):n(In3＋)=5 :5的共沉淀粉于800 ℃下灼烧4 h所得的α Fe2O3掺杂In2O3传感器元件,对45 μmol•L－1 C2H5OH的灵敏度达54.0,为相同浓度干扰气体汽油的8倍多.     

焙烧温度对Mn/Al2O3-TiO2催化剂结构及氧化NO性能的影响

采用溶胶凝胶法和浸渍法制备10% Mn/Al₂O₃-TiO₂催化剂,借助TPO、XRD、O₂-TPD、Raman、XPS等手段,考察焙烧温度(450~650 ℃)对催化剂结构以及氧化NO性能的影响。TPO结果表明催化剂活性随焙烧温度的升高先增后减,其中焙烧温度为550 ℃时催化剂活性最好。XPS结果显示随着焙烧温度的升高(450~550 ℃),催化剂表面Mn³⁺的含量逐渐升高,与催化剂活性的强弱成对应关系,并且催化剂晶格氧含量下降,而表面化学吸附氧从40.9%增加到64.8%。Raman分析显示550 ℃焙烧时,催化剂表面存在丰富的Mn₂O₃活性物种,并且O₂-TPD分析也表明随着焙烧温度的升高,晶格氧向表面化学吸附氧流动,提高了化学吸附态氧物种的含量。这些结果表明Mn₂O₃可能是NO氧化起主要作用的活性Mn物种,释放更多的表面化学吸附氧物种,将有助于促进NO的催化氧化。     

焙烧温度对Mn/Al2O3-TiO2催化剂结构及氧化NO性能的影响

采用溶胶凝胶法和浸渍法制备10%Mn/Al_2O_3-TiO_2催化剂,借助TPO、XRD、O_2-TPD、Raman、XPS等手段,考察焙烧温度(450~650℃)对催化剂结构以及氧化NO性能的影响。TPO结果表明催化剂活性随焙烧温度的升高先增后减,其中焙烧温度为550℃时催化剂活性最好。XPS结果显示随着焙烧温度的升高(450~550℃),催化剂表面Mn~(3+)的含量逐渐升高,与催化剂活性的强弱成对应关系,并且催化剂晶格氧含量下降,而表面化学吸附氧从40.9%增加到64.8%。Raman分析显示550℃焙烧时,催化剂表面存在丰富的Mn_2O_3活性物种,并且O_2-TPD分析也表明随着焙烧温度的升高,晶格氧向表面化学吸附氧流动,提高了化学吸附态氧物种的含量。这些结果表明Mn_2O_3可能是NO氧化起主要作用的活性Mn物种,释放更多的表面化学吸附氧物种,将有助于促进NO的催化氧化。     

Monolith Manganese-Based Catalyst Supported on ZrO2-TiO2 for NH3-SCR Reaction at Low Temperature

Monolith catalysts were prepared using TiO₂ and ZrO₂-TiO₂ as supports with MnO₂ as active component and Fe₂O₃ as promoter. The catalytic activities at low temperature and stability at high temperature for selective catalytic reduction of NO_x with NH₃ (NH₃-SCR) in the presence of excessive O₂ were studied after the catalysts calcined at different temperatures. The catalysts were characterized by X-ray diffraction (XRD), specific surface area measurements (BET), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results indicated that the catalyst supported on ZrO₂-TiO₂ had excellent stability at high temperature, and possessed high specific surface area and oxygen storage capacity, and had strong redox property. The results of the catalytic activities indicated that the monolith manganese-based catalyst using ZrO₂-TiO₂ as support had evidently improved the activity of NH₃-SCR reduction reaction at low temperature, and it showed great potential for practical application.     

Structural models for intergrowth structures in the phase system Al2O3-TiO2

The phase system Al₂O₃-TiO₂ was investigated in the compositional range from 48:52 to 62:38 mol% Al₂O₃:TiO₂. The samples were prepared by melting the binary oxides in an arc-imaging furnace and the obtained samples were examined by powder X-ray diffraction. The recorded powder patterns could be interpreted in terms of intergrowth structures consisting of two basic building blocks, which were deduced from the known crystal structures of β-Al₂TiO₅ and Al₆Ti₂O₁₃. The structure of a new ordered compound with the formula Al₁₆Ti₅O₃₄ is proposed. The thermal stability was estimated from DTA and tempering experiments and showed that all prepared samples decompose at temperatures around 800 °C into the binary oxides corundum and titania.     

Hybrid Inorganic-Organic Sol–Gel Coatings in the SiO2-TiO2 System

In the present work, the influence of substituted Si-alkoxides on the structural and optical properties of films obtained in the SiO₂-TiO₂ system was studied. Methyltriethoxysilane (MTEOS) and 3-(tri-methoxysilyl)propyl methacrylate (TSPM) were used as SiO₂ sources and Ti(OBu)₄ was used as TiO₂ source. Acetylacetone was added to the Ti(OBu)₄ as chelating agent and the synthesis was carried out in acid medium. The films were deposited on oxidized Si-wafers by spin-coating. The films were characterized by XRD, spectro-ellipsometry (SE), and atomic force microscopy (AFM). The results obtained have shown that in the case of hybrid films the desired thickness could be obtained in a single deposition step. The thickness of the films and the optical properties are controlled by the bulkiness of the organic substitute bounded to Si. Among other optical applications, the potential use of such films as optical waveguides is proposed.     

用于NO_x低温下吸附还原的CoO_x/CeO_2二元氧化物的制备

研究了以多孔二氧化硅微球和活性炭为载体制备NOx吸附/还原催化剂的方法,摸索了最佳Ce/Co物质的量的比例。采用低温氮吸附方法测定了样品的BET比表面和孔容,利用XRD方法表征了样品中所掺杂的金属元素的晶型。研究发现:当nCe/nCo=75/25时,材料获得最佳NOx吸附能力,当以多孔二氧化硅微球作载体时,材料对于NOx的吸附主要来自CoOx和CeO2的二元氧化物;当以活性炭作为载体时,活性炭参与了NOx的吸附,因此其吸附容量大大提高。对NOx的吸附机理进行了探讨,并研究了样品的NH3还原性质。