A novel optical burst switching architecture for high speed networks

A novel optical burst switching （OBS） high speed network architecture has been proposed. To verify its feasibility and evaluate its performance, just-enough-time （JET） signaling has been considered as a high performance protocol. In the proposed architecture, to avoid burst losses, firstly, a short-prior- confirmation-packet （SPCP） is sent over the control channel that simulates the events that the actual packet will experience. Once SPCP detects a drop at any of the intermediate nodes, the actual packet is not sent but the process repeats. In order to increase network utilization, cost effectiveness and to overcome some limitations of conventional OBS, inherent codes （e.g., orthogonal optical codes （OOC））, which are codified only in intensity, has been used. Through simulations, it shows that a decrease in burst loss probability, cost effectiveness and a gain in processing time are obtained when optical label processing is used as compared with electronic processing.     

一种新型结构光交叉连接节点及其联网性能分析

通过对常见光交叉连接器(OXC)的改进,提出了一种具有有限波长转换能力的内部光交叉连接节点(L-WIXC),既具备冲突消解能力又降低成本.采用算法编程方法,分析比较了L-WIXC和其他两种现有OXC结构,以及基于不同信令协议的L-WIXC的拥塞性能,结果表明L-WIXC具有较低的拥塞概率,并且基于JET协议的L-WIX...     

Analysis of burst/packet assembly techniques in high-speed optical switching network

In the Optical Burst Switching (OBS) Network, the burst assembly technique is one of the challenging issues in the implementation of the system. It has the influence on the burst characteristic, which gives an impact on the network performance. Burst assembly is the process of assembling incoming data from the higher layer into bursts at the ingress edge node of the OBS network. The burst assembly mechanism must then place these packets into bursts based on some assembly policy. In this paper, the OBS system performance has been observed in simulated 12-node network based on Just-Enough-Time (JET) reservation protocol with various burst assembly techniques under the standard drop policy (DP) and the segmentation policy for contention resolution. The simulation results show that the performance of the proposed Adaptive-Threshold with Fixed Maximum Time Limitation (ATH-FMTL) burst assembly scheme is better than conventional burst assembly schemes in terms of loss probability and average assembly delay. Also, the proposed scheme avoids a sudden increase in the burst size and makes the burst sent out smoother as compared to conventional schemes.     

用于WDM光突发交换网的改进JIT信令协议

提出了一种用WDM光突发交换网的良好时间通信协议(MJIT-SP)该协议结合了光线路交换和光分组交换的优点与用于光突发交换的其他信令协议相似,MJIT-SP的特点也是采用带外控制信号处理来排除核心节点处对光缓存器的需求然而,与其它协议如JIT-SP相比,它能最小化数据源端的建立时间和最大化交叉连接的带宽利用率而且,MJIT-SP还能支持光网络中无连接和面向连接的数据包传递并介绍了MJIT-SP的基本结构并从三个方面分析了它的基本性能,即建立时间、端到端延时和信道占用时间然后,对本协议与JIT-SP的性能进行了比较,结果显示:MJIT-SP不仅优于JIT-SP,而且还克服了JIT-SP的一个缺点,即过长的信道占用时间此外,还给出了MJIT-SP的信令信息,尤其是非常关键的信号与脉座电平差(SETUP)消息MJIT-SP中的SETUP与JIT-SP中的SETUP不同,它需要给出数据包路由和交换所需的信息,包括数据包长度、比特率、SETUP与数据包之间的偏置时间以及数据业务的质量控制系统(QoS)要求等最后讨论了MJIT-SP两种可能的变化并且分析了它们的优缺点.     

JET: Preparing the future in fusion

JET (Joint European Torus) is the largest tokamak in the world and the only fusion facility able to operate with Tritium, the fusion fuel, and Beryllium, the ITER first wall material. JET also features the most complete remote handling equipment for invessel maintenance. As a multinational research center, JET provides logistic experience in preparing for operation of the global facility, tokamak ITER.Experiments on JET are focused on ITER-relevant studies, in particular on detailing the operational scenarios (EL My H-modes and advanced regimes), on enhancing the heating systems, on developing diagnostics for burning plasmas etc. Pioneering real-time control techniques have been implemented that maximize performance and minimize internal disturbances of JET plasmas. In helium plasmas, ion cyclotron heating (ICRH) created fast α-particles, mimicking their populations in future burning plasmas. The recent successful Trace Tritium campaign provided important new data on fuel transport. Current enhancements on JET include a new ITER-like ELM-resilient high power ICRH antenna (7 MW) and over twenty new diagnostics that will further extend the JET scientific capabilities and push the facility even closer to the ITER parameters.A special mention is given to the involvement of the fusion experts from Association EURATOM-IPP.CR, who have been actively participating in the collective use of JET facility for more than three years.     

Hybrid OCS/OBS interconnect in intra-data-center network

We report on a data center network(DCN) architecture based on hybrid optical circuit switching(OCS) and optical burst switching(OBS) interconnect for dynamic DCN connectivity provisioning. With the combination of the centralized and distributed control of the software-defined optical networks, the proposed interconnect can achieve unprecedented flexibility in dealing with both mice and elephant flow in the DCN. Numerical simulation is employed to investigate the performance of the proposed architecture. The results show that the OBS module has preferable performance in dealing with a larger burst packet, and the throughput is constrained by the capacity of the server random access memory module.     

一种新的光突发交换网络信令协议与分析

提出了一种新的光突发交换网络信令协议,即DSH区分服务混合信令.根据实时（电路仿真）业务和非实时（数据）业务对QoS的不同要求分别采用TAW和JET信令控制协议,尤其是对TAW信令做了相应改进,使之更适合于OBS网络承载电路仿真业务.利用电路仿真业务发出的呼叫请求,在端到端的波长通道中建立虚通路,并在整个呼叫持续过程中保持虚通路的连接,这样可以保证电路仿真业务的端到端时延最小并避免信息丢失.通过理论分析和系统仿真,研究了DSH混合信令的性能及其对波长利用率和实时业务呼损率的影响.     

Novel Quantum Virtual Private Network Scheme for PON via Quantum Secure Direct Communication

Two quantum secure direct communication (QSDC) protocols with quantum identification (QI) based on passive optical network (PON) architecture are proposed. One QSDC protocol can be implemented between two different optical network units just with simple configurations of PON by optical line terminal when they are in the same virtual private network after optical line terminal performing QI to the optical network units in the given PON architecture. The other QSDC protocol is also implemented between any two legitimated users in the virtual private network but with considerable reduction of workload of the optical line terminal. The security analysis shows that the proposed QSDC schemes with quantum identification are unconditionally secure and allow the legitimate users to exchange their secret information efficiently and to realize a quantum virtual private network in the PON networks ultimately.     

Performance analysis of modified optical burst switching (OBS) ring network using dummy node

In the present paper an analytical model of an optical burst switching ring network which is capable to handle the variable incoming traffic intelligently is presented. An efficient node architecture and network operating protocol enhances the data throughput in a congested network. Here we propose a node architecture to ease the traffic congestion in a ring network involving a dummy server connected to backbone of the ring topology to ease the traffic flow into the ring by diverting the packets under the congestion situation. An appropriate mathematical model for the proposed node architecture has been developed employing packet queuing control to estimate the amount of carried traffic for different node parameters and the analysis has been further extended to investigate the network performance under different signaling techniques.     

Modeling and performance analysis of optical WDM node architecture using SRR protocol

In order to enhance the data transport capability and overall throughput of an optical wavelength division multiplexing (WDM) system, a proper node architecture design is necessary. In the present paper a simple node architecture model based on media access control protocols for bursty data traffic of variable time slot duration and data rate has been proposed to decrease the packet loss probability and to increase the efficiency of an optical WDM system using synchronous round robin (SRR) protocol. An appropriate mathematical model has been derived to evaluate performance of the proposed node architecture. It has been observed that the network performance is well controlled through implemented model and the corresponding network design parameters.     

Analysis of Wavelength-Routed Optical Burst-Switched Network Performance

This paper studies a novel scalable network architecture combining optical burst switching (OBS) with dynamic wavelength allocation to guarantee quality of service (QoS), forming a wavelength-routed optical burst-switched network. All processing and buffering functions are concentrated at the network edge and bursts are assigned to fast tuneable lasers and routed over a bufferless optical transport core using dynamic wavelength assignment. Different burst aggregation mechanisms are evaluated for a range of traffic statistics in terms of delay and packet loss rate. New network performance parameters in an analytical model quantify the advantages of dynamic wavelength allocation. The results define the operational gain achievable with dynamic wavelength assignment compared to quasi-static wavelength routed optical networks.     

Comparison analysis of optical burst switched network architectures

Optical burst switching (OBS) is a promising paradigm for the next-generation Internet infrastructure. In this paper, a novel efficient network architecture for OBS has been presented and compared with conventional OBS architectures. To enhance OBS system performance, the architecture employs a novel proposed burst assembly algorithm, fiber delay lines (FDLs) and dynamic route selection technique. A queuing model is used to predict the system behavior for both classless and prioritized traffic. Simple closed-form expressions are obtained for the burst-loss probability of both classless and prioritized traffic. Numerical results show that the proposed architecture provides an accurate fit for the performance of the highest traffic class and lower bounds for the other traffic classes that are tighter than earlier known results.     

Analysis of Wavelength-Routed Optical Burst-Switched Network Performance

This paper studies a novel scalable network architecture combining optical burst switching (OBS) with dynamic wavelength allocation to guarantee quality of service (QoS), forming a wavelength-routed optical burst-switched network. All processing and buffering functions are concentrated at the network edge and bursts are assigned to fast tuneable lasers and routed over a bufferless optical transport core using dynamic wavelength assignment. Different burst aggregation mechanisms are evaluated for a range of traffic statistics in terms of delay and packet loss rate. New network performance parameters in an analytical model quantify the advantages of dynamic wavelength allocation. The results define the operational gain achievable with dynamic wavelength assignment compared to quasi-static wavelength routed optical networks.     

Contention reduction and service differentiation in OBS networks

Optical burst switching (OBS) has been proposed to be a competitive switching technology for wavelength division networks (WDM) networks. In this switching technique, single burst loss due to contention influences loss of multiple data. Thus, burst loss ratio (BLR) is the main deciding factor for determining the performance of an OBS network. Also, inefficient data channel scheduling algorithm causes burst loss in OBS. In addition to this, the same service to all model of the current Internet is inadequate for the diverse quality of service expectations of Internet applications and users. In this paper, an efficient technique is proposed in which data burst is assembled from several Internet protocol (IP) packets in such a manner that the number of IP packets is changed according to the traffic load. In the proposed scheme, the burst is segmented because the segment located at the end of the contended burst has a greater chance of surviving contention (as the dropped segments are those at the beginning of the contending burst). Thus, the most important (or higher priority) information is enveloped in the last segmented. Further to prevent resource wastage due to over admitting of bursts, the proposed scheme is extended by admission control test for an output link without a fiber delay line (FDL) buffer. Also, modified latest available unscheduled channel with void filling (LAUC-VF) scheduling algorithm utilizing MPLS has been used to provide a scalable and manageable architecture for service differentiation (DiffServ) in IP networks. Simulation results demonstrate that the proposed technique has reduced burst loss rate and better quality of service (QoS) performance in comparison to existing techniques.     

Design and performance evaluation of a metro WDM storage area network with IP datagram support

Storage area networks (SANs) are becoming an important part of optical MANs (metropolitan area networks). Growing storage and business-continuity needs; high-bandwidth, low latency requirements for SANs; storage infrastructure consolidation; and post-9/11 regulatory issues are among the several driving factors to push this trend. We, in this paper, consider a metro wavelength division multiplexing (WDM) SAN that allows the transmission of variable packet size such as Internet protocol (IP) datagram and evaluate its performance by means of discrete-event simulation. The network is based on one fixed transmitter and multiple fixed receivers. Beginning with an introduction and the context of this work, we describe the network and node architectures; and introduce the medium access control (MAC) protocols. Subsequently, using the Poisson and self-similar traffic, we present and discuss performance of the proposed network architecture in terms of throughput and queuing delay under symmetric and asymmetric traffic scenarios. The simulation results suggested that the proposed architecture is suitable for SAN applications which demand low queuing delay and high throughput.     

An efficient packet parser architecture for software-defined 5G networks

Software-defined networks (SDN) has emerged with the capability to program in order to enhance flexibility, management, and testing of new ideas in the next generation of networks by removing current network limitations. Network virtualization and functionalization are critical elements supporting the delivery of future network services, especially in 5G networks. With the integration of virtualization and functionalization, network resources can be provisioned on-demand, and network service functions can be composed and chained dynamically to cater to various requirements. 5G networks are expected to rely heavily on SDN, which has been widely applied in core network design. To have a software-defined 5G network, not only is new spectrum and interface needed from SDN, but also a programmable and efficient hardware infrastructure is required. Admittedly, hardware components and infrastructure play an important role in supporting 5G networks. In other words, the software-defined 5G network data plane must have the required flexibility and programmability to support upcoming needs and technologies. Technological solutions need to respond to actual requests in infrastructure. Packet parsers in the data plane of software-defined 5G networks are one of the most important components because of the variation in the type of network headers and protocols. Each SDN switch needs to identify headers for processing input packets in the data plane, where the packet parser operates. Multiple implementations of packet parsers have been done on different substrates that occupy large hardware resources and areas on chip. However, they are not suitable for software-defined 5G networks. Certain architectures have been presented for packet parsing, aimed at accelerating the process of header parsing, however no attention has been paid toward reducing the area and the volume of the needed hardware resources and programmability in the data plane. This paper presents a new and efficient architecture for packet parsers on Field Programmable Gate Arrays (FPGA), called Efficient FPGA Packet Parser (EFPP) in a designed software-defined 5G network. This architecture emphasizes the removal of Ternary Content Addressable Memory (TCAM) to decrease hardware resources and efficiency in the data plane. Moreover, this architecture uses the chip’s processing speed and reconfiguration capabilities to support new protocols and network headers while maintaining flexibilities on software-defined 5G networks. EFPP is applied to chips on FPGA Xilinx ZedBoard Zynq, and the resources consumed around 7.5% LookUp Table, 1.9% Flip-Flops, and 5.8% of the memory. EFPP was also more area efficient. According to our results, EFPP would reduce the area and volume of hardware compared to other peer works.     

4 MeV直线感应加速器控制系统设计与实现

 设计了以淬发方式产生强流电子的4 MeV 直线感应加速器的基于局域网的分布式控制系统。介绍了应用FP2000分布式I/O系统和可编程序电源的硬件体系结构,阐述了在Labwindows/CVI平台上基于DataSocket服务器作为数据传输媒介的分布式系统实现方法。对系统开发中出现的DataSocket服务器数据丢失,因数据项数量庞大而带来应用程序的结构和逻辑关系难于把握两点不足,提出了对数据项进行抽象和综合,应用数据字典描述数据项,充分考虑可靠性和快速响应之间的关系,合理使用数据项的属性等有效的实现办法。     

An optimal burst assembly approach employing traffic shaping (OBATS) for OBS

Optical burst switching (OBS) aims at combining the strengths of packet and circuit switching and is considered as a promising technology for implementing the next generation optical Internet, required to cope with the rapid growth of Internet traffic and the increased deployment of new services. In this paper, an optimal burst assembly approach employing traffic shaping (OBATS) for OBS networks has been proposed in order to improve network performance in terms of reduced blocking probability, congestion control and better utilization of bandwidth. Particularly, the proposed scheme aims at reducing the average delay experienced by the packets during the burstification process in optical burst switched (OBS) networks, for a given average size of the bursts produced. Reducing the packet burstification delay, for a given average burst size, is essential for real-time applications; correspondingly, increasing the average burst size for a given packet burstification delay is important for reducing the number of bursts injected into the network and the associated overhead imposed on the core nodes. Simulation results show that the proposed burst assembly approach gives better network performance in terms of burst drop, resource contention and delay as compared to conventional burst assembly approaches.     

Integrated Contention Resolution and Control Algorithm for Optical Burst Switched Networks

Abstract

This article compares the conventional and proposed integrated contention resolution and control algorithm in optical burst switching with respect to burst loss probability and network throughput. Results have shown that the proposed approach behaves well in practice and responds quickly to any change in network status, while improving the overall network performance. It is shown that the proposed algorithm (ICRCA) not only provides significantly better burst loss performance than the conventional algorithms, but is also void of any packet re-orderings.     

Performance enhancement of optical burst switched networks

Optical burst switching (OBS) is an optical switching paradigm which offers a good tradeoff between the traditional optical circuit switching (OCS) and optical packet switching (OPS) since it has the relatively easy implementation of the first and the efficient bandwidth utilization of the second. Hence, OBS is a promising technology for the next generation optical Internet. A buffer-less OBS network can be implemented using ordinary optical communication equipment without the need for either wavelength converters or optical memories. In an OBS network, burst-loss performance is a critical concern. In OBS, the data-burst transmission is delayed by an offset time (relative to its burst control packet (BCP), or header) and the burst follows its header without waiting for an acknowledgment for resource reservation. Thus, a burst may be lost at an intermediate node due to contention, which is generally resolved according to the local routing and bandwidth information. The routing table maintained in each OBS node is generally pre-computed and fixed to forward the data bursts. Such a static forwarding feature might have limited efficiency to resolve contentions. Moreover, a burst may be lost and the network may be congested when a network element (e.g., fiber link) fails. In this paper, an efficient integrated scheme based on dynamic routing and burst segmentation has been proposed to improve reliability of data transport and network load balancing in optical burst switched networks. Simulation results demonstrate that the proposed approach reduces effectively blocking probability and hence contention. Further, it provides end-to-end throughput performance also. Hence, it establishes an appropriate tradeoff between loss rate and end-to-end throughput.