Synthesis and characterization of biodegradable polyesteramides constructed mainly by alternating diesterdiamide units from N,N′-bis(2-hydroxyethyl)-adipamide and diacids

Two kinds of aliphatic alternating polyesteramide prepolymers were prepared through melt polycondensation from N,N’-bis(2-hydroxyethyl)-adipamide and adipic acid or sebacic acid. Chain extension of them was conducted with 2,2′-(1,4-phenylene)-bis(2-oxazoline) and adipoyl biscaprolactamate as combined chain extenders. The chain extended polyesteramides (ExtPEAs) were characterized by IR, 1 H-NMR, differential scanning calorimetry, thermogravimetric analysis, wide angle X-ray scattering, tensile test and enzymatic degradation. The results showed that the ExtPEA(4,m)s were mainly constituted with the diester adipamide alternating units. ExtPEA(4,4) and ExtPEA(4,8) had Tm of 83.8℃ and 85.8℃ and initial decomposition temperature above 310.0℃. They crystallized similarly as Nylon-66 did and were flexible thermoplastic materials with tensile strength up to 25.64 MPa and strain at break up to 737%.     

含ε—己内酯链节的可生物降解聚酯酰胺的合成与表征

以ε－己内酯与乙二胺，己二胺开环加成反应生成的酰胺二元醇和己二酸为原料，合成了ε－己内酯链节的聚酰胺胺，并用ＩＲ，＾１Ｈ ＮＭＲ，＾１３Ｃ ＮＭＲ和ＤＳＣ进行了表征，该类聚酯酰胺是半晶性聚合物且能够发生生物降解。     

Aliphatic Segmented Poly(ether ester amide)s Synthesized from Hexanediamine,Sebacic Acid and Poly(ethylene glycol)s

High molecular weight aliphatic segmented poly(ether ester amide)s(PEEAs) were synthesized via melt polycondensation and chain extension. An oligomeric polyamide(PA) terminated mainly with -COOH groups(HOOC-PA-COOH) was prepared from the reaction of nylon 610 salt with sebacic acid. Melt polycondensation of HOOC-PA-COOH with polyethylene glycol(PEG), such as PEG400, PEG600, PEG1000 and PEG1500, was conducted at 200℃, and several segmented PEEA prepolymers(PrePEEAs) were prepared. Chain extension of PrePEEAs was carried out at 190℃ using 2,2'-(1,4-phenylene)-bis(2-oxazoline) and adipoyl biscaprolactamate as combination chain extenders. Chain extended PEEAs(ExtPEEAs) were characterized by gel permeation chromatography(GPC), Fourier transform infrared spectrophotometer(FTIR), proton nuclear magnetic resonance(¹H NMR), differential scanning calorimetry(DSC), wide angle X-ray scattering(WAXS), thermogravimetry analysis(TGA), and tensile test. The ExtPEEAs exhibited M_n up to 98700, T_m from 164.2℃ to 176.1℃, initial decomposition temperature above 320.6℃, tensile strength up to 34.80 MPa, and strain at break from 111.92% to 353.12%. Aliphatic segmented PEEAs with good thermal and mechanical properties were prepared.     

乙醇酸和DL─乳酸交替共聚物的合成和表征

乙醇酸和ＤＬ－乳酸交替共聚物具有不同于其无规共聚物的理化性能和生物降解性。以ＤＬ－３－甲基－１，４－二烷－２，５－二酮为单体，通过在辛酸亚锡引发下的本体开环聚合，合成了该交替共聚物，并进行了结构表征。     

扩链法合成聚乳酸类生物降解材料

详细地综述了聚乳酸类生物降解材料的扩链法合成，特别是使用二异氰酸酯类、二恶唑淋类扩链剂的合成进展。参考文献37篇。     

可生物降解聚酯酰胺的合成及其对药物缓释作用的研究

通过酰胺二元醇、1，4－丁二醇、己二酸的无规共聚得到了富含酯链段的可生物降解聚酯酰胺。以对硝基苯胺为模型药物，初步研究了不同载药量时的释药行为及分子量对药物释放的影响。     

Characterization of the Charge Transfer Complex from Furan and Maleic Anhydride and the Alternating Copolymer

A previously unreported copolymer between furan and maleic anhydride was readily obtained by free radical initiation of benzene solutions of the comonomers. The product copolymers exhibit remarkably uniform composition regardless of monomer feed ratios. A donor-acceptor complex was suspected to account for the 1:1 alternating sequence of the monomers in the product. The complex was easily detected and partially characterized, although its exact role in the mechanism is uncertain.     

交流示波极谱滴定法测定吡哌酸

本文介绍用交流示波极谱滴定法测定吡哌酸的含量。在ＨＣｌ－ＮａＡｃ缓冲溶液中，加入过量的Ｎａ－ＴＰＢ与吡哌酸作用生成沉淀，过滤后用亚铊标准溶液定滤液中过量的ＴＰＢ，由交流示波极谱图上ＴＰＢ的切口消失指示终点。本法操作简便，终点直观，应用于原料药样品的测定，并与药典法相对照，结果基本吻合。     

Synthesis and Characterization of Photocrosslinkable Biodegradable Polymers Derived from 4‐Hydroxycinnamic Acid

A novel series of photocrosslinkable biodegradable polymers was prepared by a high‐temperature solution polycondensation from a dichloride of 4,4′‐(adipoyldioxy)dicinnamic acid (CAC) and alkane diols of various methylene lengths (HO(CH₂)_nOH; n = 6–10) or poly(ethylene glycol)s (PEG) of various molecular weights . The CAC was synthesized by the condensation of adipoyl chloride and 4‐hydroxycinnamic acid. The chemical structures and properties of these polymers were characterized by elemental analysis, ultraviolet‐visible spectroscopy (UV‐VIS), Fourier transform infrared spectroscopy (FT‐IR), ¹H NMR spectroscopy, differential scanning calorimertry (DSC), and thermogravimetry (TG). All polymers had a high molecular weight and good solubility in organic solvents. DSC showed that T_m values of CACn (134–180 °C) were much higher than those of CACEm (25–56 °C). The CACE200 degraded very rapidly in the buffer solutions (pH 7.2) of Ps. Cepacia or Rh. delemar lipase at 37 °C, while CACn resisted the hydrolysis by these lipases during the test period. The ultraviolet light irradiation (λ ≥ 280 nm) caused the photocrosslinking reaction by an intermolecular dimerization at ambient temperature without a photosensitizer, as examined by UV‐VIS, FT‐IR spectroscopy, and gel formation. The gels prepared from CACEm (m ≈ 1 000) were swollen in water and showed characteristic properties of a hydrogel. The irradiation time and the molecular weight of PEGs controlled the degree of swelling of these hydrogels. The CACE8 300 gel irradiated for 20 min showed the largest degree of swelling of 10.5.

Weight loss of a CACE200 film as a function of time in a phosphate buffer solution containing no lipase (□), Ps. cepacia lipase (?), or Rh. delemar lipase (○) at 37 °C.     

氨基酸衍生可生物降解聚酯酰胺的合成与表征

以L-酪氨酸、乙二醇与4种不同的二酸酰氯为起始材料合成了4种具有酚羟基侧链的聚酯酰胺.用FT-IR、NMR表征了聚酯酰胺的化学结构;DSC、TG分析了聚合物的热性质;乌氏黏度计法测算了合成聚合物的特性黏度值,研究了聚酯酰胺的亲水性与主链结构的关系.结果表明:合成了预期结构的聚合物,该聚合物的玻璃化温度较低,而热分解温度较高,具有较好的热处理性能.同时,随着主链中柔性链段增加,玻璃化温度与热分解温度随之降低,热稳定性变差,在相同时间的吸水率明显提高.     

由脂肪族二酰胺二醇合成聚酯酰胺及表征

利用脂肪族二元酸酯与乙醇胺反应容易获得的对称二酰胺二醇,经缩聚合成聚酯酰胺预聚体,并针对端羧基和端羟基同时扩链来提高分子量,获得可生物降解的聚酯酰胺.首先将N,N′-二(2-羟乙基)草酰胺(HEOA)或N,N′-二(2-羟乙基)己二酰胺(HEHA)与己二酸和丁二醇缩聚,制备同时带有端羧基及端羟基的脂肪族聚酯酰胺预聚体,通过1,4-双(2-噁唑啉)苯及己二酰双己内酰胺混合扩链剂扩链,获得高分子量脂肪族聚酯酰胺,并通过红外、1H-NMR、DSC及TGA对其结构和热性能进行了表征.结果表明,预聚体在制备过程发生了一定的酯-酰胺交换反应;扩链后聚合物的熔点、熔融焓和热稳定性有所下降;但热稳定性仍接近或略高于聚己二酸丁二酯.     

生物可降解封堵器材料的合成及表征

以L型丙交酯(LLA)、乙交酯(GA)和三亚甲基碳酸酯(TMC)为原料,辛酸亚锡为催化剂,通过开环聚合制备了丙交酯-三亚甲基碳酸酯二元共聚物(PLT)和丙交酯-三亚甲基碳酸酯-乙交脂(PLTG)三元共聚物。采用核磁共振氢谱、傅里叶红外光谱、体积排阻色谱、差热扫描、力学性能测试、血液相容性实验表征了产物的结构与性能,研究了共聚物组成对其结晶能力、热性能和力学性能的的影响。结果表明:所得聚合物的数均分子量均在8×10~4以上,多分散系数在2.0以下。共聚物中的TMC和GA链段使其结晶能力、玻璃化转变温度和拉伸强度与L型聚丙交酯相比均有所下降。三元共聚物PLTG的拉伸强度可达到22.3 MPa,断裂伸长率达到168.7%。另外,共聚物的血液相容性优良。     

2种癸二酸咪唑啉季铵盐的合成及缓蚀性能评价

合成了2种癸二酸咪唑啉季铵盐癸二酸-水杨酸咪唑啉季铵盐(SSAI)和癸二酸咪唑啉季铵盐(SAI),并采用失重法和电化学方法研究了这2种咪唑啉季铵盐对N80钢在1 mol/L HCl溶液中的缓蚀性能和吸附行为。 结果表明,在1 mol/L HCl溶液中这2种化合物对N80钢均有较好的缓蚀作用,缓蚀效率大小顺序为SSAI＞SAI。 SSAI和SAI均为混合偏阳极型缓蚀剂。 2种化合物在N80钢表面的吸附服从Langmuir吸附等温式,属于化学吸附。     

可降解聚氨酯丙烯酸酯生物材料的制备及其表征

以端羟基聚丙交酯(PLLA)为软段,六亚甲基二异氰酸酯(HDI)和甲基丙烯酸羟乙酯(HEMA)为硬段聚合得到端基为双键的低聚物,再在UV照射下固化得到可生物降解的聚氨酯丙烯酸酯(PUA)生物组织工程材料.PLLA由1,4-丁二醇引发L-丙交酯(L-LA)开环得到.PLLA和低聚物的组成结构用NMR和GPC进行了表征.对固化聚合物PUA的热性能(DSC和TGA)、力学性能(DMA和拉伸)和亲水性(接触角和溶胀)的研究表明增加PLLA软段会增加材料的Tg,但降低材料的亲水性和交联度.PLLA500-HDI的拉伸强度为6.7 MPa,可以满足生物材料的力学性能要求.通过体外降解实验,发现增加PUA材料的软段,降解速率下降.降解16周后,PLLA500-HDI降解最快,失重15.8%,而PLLA2000-HDI的降解速率最慢,失重5.5%,可能与其微相分离的结构有关.红外(ATR)分析表明降解的PUA膜中N—H的伸缩吸收峰(3364 cm-1)变宽和C O吸收峰变尖锐,说明主链中酯键和氨基甲酸酯键都发生了水解.热失重(TGA)曲线上PLLA500-HDI和PLLA1000-HDI降解后的PUA材料热稳定性下降,而PLLA2000-HDI变化不大.此外,在SEM图中发现降解的PLLA500-HDI膜表面出现裂纹和孔洞,PLLA2000-HDI材料表面也形成相分离结构.细胞实验说明材料支持细胞的黏附,有较好的生物相容性,具有应用于组织工程的潜力.     

pH敏感超支化聚合物的合成与表征

均苯四甲酸酐、乳酸和L-谷氨酸在SnCl2.2H2O催化下一步合成了pH敏感的超支化聚(乳酸-谷氨酸)共聚物(PGLA)。核磁共振谱分析结果显示:PGLA分子链由聚乳酸和支化的聚谷氨酸单元组成,未出现戊二酰亚胺环状结构片段,所得共聚物具有良好的pH敏感性,可溶于pH≥7.4的碱性水溶液,pH=9时,在水中所形成的胶粒体积最大。     

阻抗滴定法测定巯基乙酸及其混合自组装膜表面酸度

采用循环伏安和交流阻抗法对巯基乙酸及其混合自组装膜的表面酸性基团的离解特性进行了研究,并利用阻抗滴定曲线得出了巯基乙酸及其混合自组装膜的表面酸度。研究了混合组装电极中其他组分含量的变化、支持电解质的离子强度等因素对表面酸度移动的影响,用氢键作用、疏水相互作用及分子间相互作用对实验结果进行了解释。     

A Transformable and Bulky Methacrylate Monomer That Enables the Synthesis of an MMA-nBA Alternating Copolymer: Sequence-Dependent Self-Healing Properties

In this study, we designed a methacrylate molecule with an alkyl-substituted trichloro salicylic acid pendant as a transformable bulky monomer to enable the synthesis of an alternating copolymer of methyl methacrylate (MMA) and n-butyl acrylate (nBA). The adamantyl-substituted methacrylate monomer ( 1-Ad ) showed very low homopolymerization propensity in radical polymerizations, but afforded the alternating copolymer with nBA via copolymerization. The 1-Ad units in the resultant copolymer were quantitatively and selectively transformed into MMA via transesterification with methanol to yield the alternating copolymer of MMA and nBA. Its alternating sequence was clearly demonstrated by a structural analysis via ¹³C NMR spectroscopy as well as the low reactivity ratios for the 1-Ad and nBA pair. Finally, we verified the superior self-healing ability of the alternating copolymer compared to that of the corresponding 1 : 1 statistical copolymer.     

Synthesis and Characterization of Chitosan-Albumin Conjugates as pH-Sensitive Biodegradable Hydrogels

A new kind of biodegradable pH-sensitive drug delivery system was developed via chitosan-albumin conjugate hydrogel. Through changing the feeding modes of reactants, two types of hydrogels(comb-type and reticular-type) were synthesized by amidation reactions between 6-O-succinoylated N-phthaloyl chitosan and albumin. The structures and morphologies of the hydrogels were characterized by SEM. And their water swelling capacity, drug loading and releasing properties at different pH values were also investigate...     

Synthesis, characterization and properties of high molecular weight poly(butylenes succinate) reinforced by mesogenic units

To increase the molecular weights of the synthesized liquid crystalline aromatic/aliphatic copolyesters and to avoid crosslinking, a solution polymerization of the prepolymer and chain extender hexamethylene diisocyanate was adopted. The effects of chain extension on polyester molecular weights, thermal and mechanical properties, and biodegradable behaviors were investigated respectively. The catalysis mechanism and the copolyesters morphological textures were also investigated. The synthesized copolyesters were characterized by means of Fourier transform infrared spectra (FTIR), gel permeation chromatography (GPC), viscosity measurements, differential scanning calorimetry (DSC), X-ray diffraction (XRD), polarizing light microscopy (PLM), scanning electron microscopy (SEM) and mechanical property measurements. It was found that inherent viscosities and the molecular weights of the copolyesters were remarkably increased under the action of catalyst, leading to a increase in the tensile strength. The degree of relative crystallinity, the melting temperature, and the rate of degradation decreased after chain extension.     

Synthesis and Characterization of Triphenyltin(IV) Carboxylates with Isophthalic Acid and Benzoic Acid Derivatives: X‐ray Crystal Structures of 1D Supramolecular Chains

The reaction of triphenyltin(IV) hydroxide with the isophthalic acid and benzoic acid derivatives, 5‐(1,3‐dioxo‐1,3‐dihydro‐isoindol‐2‐yl)‐isophthalic acid (H₂L¹) and 4‐(1,3‐dioxo‐1,3‐dihydro‐isoindol‐2‐yl)‐benzoic acid (HL²) yielded the complexes [(SnPh₃)₂L¹] ( 1 ) and [(SnPh₃)L²] ( 2 ). All complexes were characterized by elemental analysis and FT‐IR and NMR (¹H, ¹³C, ¹¹⁹Sn) spectroscopy. Interestingly, the supramolecular structures of 1 and 2 are found to consist of 1D molecular chains built up by intermolecular C–H ··· O hydrogen bonds. Their thermal stabilities were also investigated.