成膜条件对聚醚砜超滤膜性能和结构的影响

以聚醚砜(PES)为膜材,聚乙二醇600(PEG600)为添加剂,N,N-二甲基甲酰胺(DMF)为溶剂,纯水为凝固浴,用相转化法制备聚醚砜超滤膜.详细探讨了PES浓度、添加剂含量、凝固浴温度对膜性能和结构的影响规律,确定了制备高水通量、高截留率聚醚砜超滤膜的最佳工艺条件.     

小分子醇对PVDF／PFSA共混膜凝胶动力学、膜结构及膜性能的影响

以小分子醇为添加剂,研究了小分子醇对聚偏氟乙烯(PVDF)/全氟磺酸(PFSA)共混超滤膜凝胶动力学、结构与渗透性能的影响.结果表明:在PVDF/PFSA铸膜液中添加乙醇时,其凝胶速率随乙醇浓度的增加而加快,超滤膜通量随乙醇浓度的增加而增大;而当添加相同浓度的4种小分子醇时,初始凝胶速率差别不大,20 s后添加乙醇的铸膜液的凝胶速率最大;添加小分子醇后超滤膜的水通量大小顺序为:异丙醇<甲醇<乙醇<正丁醇.SEM照片显示在铸膜液中添加5%乙醇所制备的共混超滤膜具有较为圆整的内腔结构与均匀的孔结构.     

自支撑海藻酸钙水凝胶抗污染过滤膜的制备及截留性能

以聚乙二醇(PEG)为致孔剂制备了自支撑海藻酸钙(CA)水凝胶过滤膜.通过数码照片及扫描电镜观察膜的表面形貌,探讨了膜的力学性能的压缩率、通量与压力的关系.研究了海藻酸钠浓度、致孔剂浓度对纯水通量和溶菌酶(Lyz)截留性能的影响.结果表明,海藻酸钠浓度越低,PEG浓度越高,膜的通量越大,压缩率也越大.膜通量随着跨膜压力的增加呈现先上升后稳定的趋势.Lyz和牛血清蛋白(BSA)溶液的稳定通量分别为纯水通量的89.97%和94.6%,表明海藻酸钙水凝胶过滤膜具有良好的抗蛋白质污染性能.膜对乳化油的过滤通量为纯水通量的93.04%,且截留率高达99.85%.对于不同分子量PEG的截留结果表明,当PEG分子量大于致孔剂的分子量时,截留率达到90%以上.以低分子量PEG400为致孔剂制备的水凝胶过滤膜对染料亮蓝的截留率达到99.75%,表明该水凝胶膜具有作为纳滤膜的前景.     

PSF-SPES共混中空纤维超滤膜制备的研究

以聚砜(PSF)、磺化聚醚砜(SPES)和醋酸纤维素(CA)为膜材料,水为内凝胶剂,采用干湿法制备了PSF-SPES共混中空纤维超滤膜,探讨了PSF-SPES铸膜液中SPES离子交换容量(IEC)、SPES浓度、添加剂、外凝胶剂的选择和热处理对膜性能的影响。所得共混超滤膜性能如下:w=0.0 0 1的Na2SO4截留率19.9%,通量62 L/(h.m2.MPa);w=0.001的PEG4000截留率78.2%,通量85 L/(h.m2.MPa)。此外,以PSF-SPES中空纤维为支撑膜,采用醋酸纤维素作为涂层液,研究了CA/PSF-SPES复合超滤膜性能,讨论了CA/PSF-SPES共混中空纤维超滤膜结构。     

脱溶剂速度对聚砜/磺化聚砜合金膜结构和性能的影响

介绍了铸膜液温度、成膜过程中的蒸发时间、环境湿度、凝胶浴温度对聚砜/磺化聚砜合金膜的渗透、分离性能的影响.随环境相对湿度、凝胶浴温度增大,合金膜的水通量增大,截留率下降;蒸发时间延长,合金膜的水通量通过一个极大值,截留率呈现下降趋势.     

纤维编织管增强型中空纤维膜研究

采用二维编织技术将聚丙烯腈(PAN)长丝编织成中空纤维编织管作为增强体,分别以聚丙烯腈(PAN)和聚偏氟乙烯(PVDF)为成膜聚合物,N,N-二甲基乙酰胺(DMAc)为溶剂,聚乙烯吡咯烷酮(PVP)为添加剂,调制铸膜液,采用同心圆挤出-涂覆法制备了PAN纤维编织管同质增强型PAN中空纤维膜和异质增强型PVDF中空纤维膜.研究表明,所得PAN纤维编织管增强型中空纤维膜断裂强度最大可超过75 MPa,在伸长率10%范围内,表面分离层与增强体之间界面结合良好;表面分离层具有类似于非对称膜的结构,铸膜液可浸入纤维编织管纤维空隙中,铸膜液浸入部分固化后未影响膜的通透性能;随成膜聚合物浓度增加,膜纯水通量减小,牛血清白蛋白(BSA)截留率增大;随添加剂PVP浓度增加,膜的纯水通量先增大后减小,在8 wt%左右达最大值,BSA截留率随PVP浓度增加而单调增加;同质增强型中空纤维膜界面结合程度优于异质增强型.     

酚酞型聚醚砜(PES-C)超滤膜的制备及性能北大核心CSCD

以聚乙烯吡咯烷酮(PVP)和乙醇(EtOH)为添加剂,采用相转化法制得了酚酞型聚醚砜(PES-C)超滤膜。结果表明:当以乙醇为添加剂时,随着乙醇含量的增加,膜上表面变为致密结构,下表面呈多孔结构,水通量先上升后减小;当以PVP为添加剂时,随着PVP含量增加,PES-C膜的指状孔得到发展,膜通量和截留率都上升,当PVP的质量含量为10%时,PES-C膜的通量达到134.3L/(m2.h),对牛血清蛋白的截留率达85.1%。     

抗油污染α-纤维素中空纤维超滤膜油-水分离性能的研究

以α-纤维素为原料,一水合N-甲基吗琳-N-氧化物(NMMO.H2O)为溶剂,聚乙二醇(PEG400)为添加剂,去离子水为内外凝胶浴,采用浸入相转化法制备用于油水分离的中空纤维非对称超滤膜,并采用纯水通量表征了膜的性能.用纤维素中空纤维超滤膜进行油水分离实验,油水乳液的截留率可达到99%以上,渗透液含油量小于10 mg/L,达到国家环境保护排放要求.考察了物理清洗、物理清洗加0.1 mol/L HCL清洗、物理清洗加0.1 mol/L NaOH清洗3种清洗方法对油水污染后膜的清洗效果.其中,物理清洗加0.1 mol/LNaOH清洗的清洗方法的通量恢复率达到99%.与其它种类的膜相比,α-纤维素中空纤维膜的油水通量衰减率仅为9.5%,表现出优异的抗油污染性能.     

聚间苯二甲酰间苯二胺中空纤维膜研究

以聚间苯二甲酰间苯二胺(PMIA)为成膜聚合物,N,N-二甲基乙酰胺(DMAc)为溶剂,氯化钙(Ca Cl2)、氯化锂(Li Cl)和聚乙二醇(PEG)为添加剂,调制铸膜液,采用干—湿法纺丝技术制备了PMIA中空纤维膜.研究表明,PEG的加入可显著提高PMIA中空纤维膜的纯水通量,而随PEG添加量增加,膜的纯水通量呈现先增加后减小趋势;膜对牛血清蛋白(BSA)有较好的截留性能,截留率可达92%;膜具有良好的亲水性能,膜对纯水接触角可低至44°;膜的断裂强度达5.8 MPa,具有较好的力学性能,以及良好的耐热水和耐碱性能,可用于高温和碱性水处理等领域.     

聚氯乙烯-聚乙烯醇的相容性及其复合多孔膜的结构与性能

通过溶液成膜法制备了聚氯乙烯-聚乙烯醇(PVC-PVA)复合多孔膜,从聚合物混合焓及分子之间相互作用的角度探讨了PVC和PVA两者之间的相容性,采用扫描电子显微镜(SEM)、接触角测量仪及平板超滤膜测试仪等分析了复合多孔膜的孔形貌、亲水性、过滤性能及力学性能.研究结果表明,在PVC-PVA复合体系中,大分子之间可形成氢键及偶极相互作用,混合焓随PVA在聚合物中质量分数的增大而呈现先增大后减小的趋势, PVC-PVA总体上为部分相容.与纯PVC膜相比, PVC-PVA复合多孔膜断面的“指状孔”特征减弱,而“海绵孔”特征增强,且纯水通量增大、耐污染性能改善、力学韧性增强.当PVA在聚合物中的质量分数为9%时,复合多孔膜的纯水通量是纯PVC膜的4倍,对PEG100000的截留率为80%,强度为3.5 MPa,断裂伸长率为26%,在水处理领域具有良好的应用前景.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.