The separation of platinum, palladium and gold from silicate rocks by the anion exchange separation of chloro complexes after a sodium peroxide fusion: an investigation of low recoveries

A series of experiments was undertaken to measure the recovery efficiency of platinum, palladium and gold from silicate rocks using a sodium peroxide fusion followed by anion exchange separation of the analytes as chloro complexes. Results obtained by graphite furnace atomic absorption spectrometric analysis of standard solutions prepared in dilute HCl or HCl-acidified sodium peroxide solution showed that recoveries were near quantitative. However, when standard solutions were added to an alkaline sodium peroxide solution, which was then acidified, low results were obtained for platinum and gold (46% and 76% respectively). Low and variable results were also obtained when standard solutions were added to a peridotite sample that had been dissolved by the state procedure, and in the analysis of the South African Bureau of Standards certified reference material, SARM 7. Various experiments were undertaken to investigate these low recoveries, but the reason proposed here is the formation of hydroxychloro compounds in alkaline solution which are not, on acidification with HCl, converted quantitatively to the chloro complex necessary for quantitative anion exchange separation. It is concluded that a sodium peroxide fusion followed by an anion-exchange separation does not appear to form the basis of a successful technique for the determination of platinum, palladium and gold in silicate rocks.     

Isomerization and Cleavage of Allyl Ethers of Carbohydrates by Trans- [Pd(NH3)2Cl2

Allyl ethers are widely used for the “temporary” protection of hydroxy groups in carbohydrates. The allyl group is conveniently removed by isomerization and subsequent cleavage of the labile prop-1-enyl group.² The rearrangement of allyl ethers to prop-1-enyl ethers is readily achieved by treatment with potassium t-butoxide in dimethyl sulfoxide, using tris(tripheny1phosphine)rhodium chloride, palladium on activated charcoal and by an ene reaction with diethylazodicarboxylate. acidic conditions, ozonolysis followed by alkaline hydrolysis, reaction with alkaline permanganate solution, or treatment with mercuric chloride in the presence of mercuric oxide. The isomerization of allyl ethers to prop-1-enyl ethers can also be carried out in the presence of palladium on carbon or complex bis(benzonitrile)palladium(11) chloride. Bruce and Roshan-Ali' showed that derivatives of allyl phenyl ether are smoothly cleaved by this complex. This has made it possible to remove the protecting group in a one-pot operation. We have now investigated the effect of palladium catalysts on the isomerization and cleavage of the allyl group in carbohydrate derivatives.     

Separation of metal ions on a modified aluminium oxide

The possibility of application of a sulpho-derivative of an aromatic organic complexing agent for separation of cations on aluminium oxide has been investigated. Alumina modified with Nitroso-R salt is used for recovery of cobalt from a tap water and for selective separation of palladium from rhodium.     

Alkyl ketoximes as analytical reagents. XI

Summary The 4-heptanone oxime extraction procedure may be used for the quantitative separation of trace amounts of palladium from a noble-metals-bearing sulfide concentrate. An average palladium value of 0.335 oz/ton was obtained on a standard sample compared to the recommended value of 0.37 oz/ton.

---

Zusammenfassung Für die quantitative Abtrennung von Palladiumspuren aus einem edelmetallhaltigen Sulfidkonzentrat eignet sich die Extraktion mit 4-Heptanonoxim. In einer Standardprobe, deren Palladiumgehalt mit 0,37 Unzen/Tonne angegeben war, wurden durchschnittlich 0,335 Unzen/Tonne gefunden.

     

Extraction of palladium and platinum with trioctylphosphine oxide (TOPO) in various solvents from hydrochloric and hydrobromic acid media

The extraction of palladium and platinum with trioctylphosphine oxide (TOPO) in cyclohexane, chloroform, methyl isobutyl ketone (MIBK) and 2,2′-dichlorodiethyl ether (DCDE) from hydrochloric and hydrobromic acids in dependence on the concentration of the acids and the extractant has been investigated. The obtained relation have been discussed and the possibilities of the separation of palladium, platinum, gold and their simultaneous extraction have been pointed out.     

Task-specific ionic liquid for solubilizing metal oxides

Protonated betaine bis(trifluoromethylsulfonyl)imide is an ionic liquid with the ability to dissolve large quantities of metal oxides. This metal-solubilizing power is selective. Soluble are oxides of the trivalent rare earths, uranium(VI) oxide, zinc(II) oxide, cadmium(II) oxide, mercury(II) oxide, nickel(II) oxide, copper(II) oxide, palladium(II) oxide, lead(II) oxide, manganese(II) oxide, and silver(I) oxide. Insoluble or very poorly soluble are iron(III), manganese(IV), and cobalt oxides, as well as aluminum oxide and silicon dioxide. The metals can be stripped from the ionic liquid by treatment of the ionic liquid with an acidic aqueous solution. After transfer of the metal ions to the aqueous phase, the ionic liquid can be recycled for reuse. Betainium bis(trifluoromethylsulfonyl)imide forms one phase with water at high temperatures, whereas phase separation occurs below 55.5 degrees C (temperature switch behavior). The mixtures of the ionic liquid with water also show a pH-dependent phase behavior: two phases occur at low pH, whereas one phase is present under neutral or alkaline conditions. The structures, the energetics, and the charge distribution of the betaine cation and the bis(trifluoromethylsulfonyl)imide anion, as well as the cation-anion pairs, were studied by density functional theory calculations.     

Application of Imidazolylazo Resin : Separation of Palladium(II), Silver(I) from Synthetic Mixtures,Medicinal and Geological Samples

ABSTRACT

A resin (I) containing imidazolylazo functional group has been used for the separation and preconcentration of palladium(II) and silver(I) from other metal ions in synthetic mixture, ores, alloys and medicinal samples. No interference could be observed from alkali and alkaline earth metal. Palladium(II) is quantitatively separated from ores and platinum wire without interferences.     

Improved separation of palladium species in biological matrices by using a combination of gel permeation chromatography and isotachophoresis

The binding of palladium to high-molecular-mass compounds in palladium-treated lettuce is investigated as an example for a biological matrix. The total palladium concentration in lettuce leaves is 10.3 ng/g wet weight. After homogenization, high-molecular-mass compounds (> 10 kDa) are isolated by ultrafiltration. For separation of these palladium species a combination of preparative gel permeation chromatography (GPC) and preparative isotachophoresis (ITP) is used. Palladium is determined in separated fractions by using a highly sensitive total reflection X-ray fluorescence (TXRF) method after preconcentration. After GPC separation, four main fractions of palladium species are collected, each containing palladium in ng quantities (3-10 ng). Two of these fractions are further separated by ITP, yielding at least three main peaks per GPC fraction, each containing palladium in the range of 0.3-3 ng. These palladium containing peaks are characterized by high-performance size exclusion chromatography (HPSEC) and capillary isotachophoresis (cITP) in parallel. HPSEC enables the estimation of the molecular mass of six main palladium peaks, covering a molecular mass range of 69-200 kDa. It is also shown that the estimation of molecular mass after separation is more reliable than the respective estimation directly in the first GPC run. However, cITP reveals that each of the separated peaks is still a mixture of at least five different compounds.     

The effect of thermal pretreatment on the electrochemical response for palladium in aqueous media

Previous work on the electrochemistry of palladium in aqueous acid solution demonstrated the existence of two multilayer hydrous oxide reduction peaks, one at ca. 0.24 V and another at ca. 0.55 V vs. RHE, plus the presence of a reversible active surface state transition at ca. 0.24 V. In the present work with thermally activated palladium it was observed that, in agreement with the hydrous oxide reduction behaviour of the system, there is a second active state transition at E≥ca. 0.45 V. In most of its reactions in aqueous acid solution, apart from its unusual capacity to absorb hydrogen, palladium exhibits properties very similar to those of platinum; however, palladium seems to be more prone to dissolution and subsurface oxygen formation. Also the premonolayer oxidation responses of these two metals are often different as the more active state of the palladium surface is not as readily generated as that of platinum. The electrocatalytic properties of palladium, as reported earlier, correlate quite well with the hydrous oxide and premonolayer oxidation behaviour of this electrode system. Electronic Publication     

Calorimetric study of methane interaction with supported Pd catalysts

As supported palladium oxide catalysts present the best performances in methane combustion in lean conditions, microcalorimetric studies of the interaction between methane and palladium oxide or metallic palladium supported on Al₂O₃, ZrO₂ and BN have been performed at 673 K. At this temperature methane reduced the palladium oxide, and the heat of reduction of palladium oxide was shown to depend on the dispersion and on the support. The lowest heats of reduction corresponded to the highest rates of methane combustion. Moreover methane reforming occurred on metallic palladium, producing hydrogen, and again methane decomposition was shown to depend on the support. This revised version was published online in July 2006 with corrections to the Cover Date.     

Solvent extraction separation of hafnium with 4-methyl-3-pentene-2-one

A new method for the extractive separation of hafnium from zirconium is presented. Zirconium is extracted with pure mesityl oxide from 4M nitric acid/4M sodium nitrate medium, followed by extraction of hafnium with mesityl oxide from 0.4M hydrochloric acid/2M ammonium thiocyanate medium. It is possible to accomplish clean separations of Hf from Zr in ratios from 1:20 to 1:200. The separation of hafnium from commonly associated elements such as scandium, yttrium, uranium, thorium, alkali and alkaline earth metals in 500:1 weight ratio to hafnium is also possible.     

Mesoporous palladium-the surface electrochemistry of palladium in aqueous sodium hydroxide and the cathodic reduction of nitrite

The voltammetry of nanostructured palladium layers electrodeposited from a hexagonal liquid crystal phase onto platinum microdiscs show well defined peaks for the adsorption/desorption of hydrogen and surface oxidation/reduction in 2 M NaOH. These peaks are more clearly resolved than at smooth palladium and reveal the complications associated with hydrogen adsorption/desorption on palladium in aqueous alkaline solutions. The reduction of nitrite at the nanostructured palladium is also reported and it is shown that it occurs via a mechanism involving a chemical reaction between adsorbed hydrogen and adsorbed nitrite ion.     

Substoichiometric determination of traces of palladium by neutron-activation analysis

A highly selective, rapid one-step radiochemical separation procedure for palladium has been developed. It is based on the solvent extraction of palladium diethyldithiocarbamate from a 5M hydrochloric acid solution with a substoichiometric amount of copper diethyldithiocarbamate in chloroform. The separation has been applied to the determination of traces of palladium by neutron-activation analysis, in platinum, the rocks W-1 and PCC-1 and a biological material (kale). Amounts of palladium down to 10(-8) g have been determined.     

Palladium catalysts on porous nickel substrates for alcohol fuel cells

Parameters characterizing the active surface of catalytic palladium layers formed from mixed glycinate-chloride and ammonia complexes of palladium(II) were determined. Cyclic voltammetry on a rotating disc electrode was used to study the catalytic activity of nickel substrates and palladium layers in the reaction of methanol and ethanol oxidation in an alkaline medium. It was shown that electrodes with palladium deposited from mixed glycinate-chloride solutions have a higher catalytic activity that those formed from ammonia palladium(II) complexes.     

Metallic film formation using direct micropatterning with photoreactive metal complexes

Palladium, cobalt, and nickel in complex with photoacid-generating ligands, 4-(2-nitrobenzyloxycarbonyl)catechol and 4-(6-nitroveratryloxycarbonyl)catechol, were prepared in solution. Films formed from the metal complex solutions perform as positive-tone, directly photopatternable palladium, cobalt, nickel oxide, or composite film precursors. After exposure, acid-bearing selectively soluble complexes could be removed to give patterned films upon developing in aqueous base, which were transformable to the corresponding pattern-preserving metal/metal oxide film. The photodynamics of photoinduced solubility and direct micropatterning of palladium, cobalt, nickel, and palladium/nickel oxide composite films were investigated. Employing palladium as the initiator for autocatalytic chemical plating, selective direct copper plating on palladium film on polyethylene naphthalate and palladium/nickel oxide composite film on glass was accomplished.     

Effect of Dissolving Temperature on the Amount of Palladium Dissolved in Borosilicate Glass

To clarify the dissolving behavior of palladium, the effect of temperature on the amount of palladium dissolved in borosilicate glass was investigated. Glass and palladium oxide, selected as a starter material, were mixed and heated at prescribed temperature. The amount of dissolved palladium became higher with temperature increasing up to 850 °C, and lower above 850 °C. Above 850 °C, the reduction of palladium oxide was accelerated. For palladium dissolution in borosilicate glass, not only the viscosity and basicity of the glass but also the decomposition temperature of the initial palladium species seemed to affect the amount of palladium dissolved in glass.     

On the reactivity of innercomplex-bonded palladium : A new specific test for cyanides in alkaline solutions

It has been found that the innercomplex salts of palladium with dimethylglyoxime, (benzildioxime and furildioxime), salicylaldoxime and 8-hydroxyquinolinc do not enter into redox reaction with carbon monoxide, cither in solid or in molecular dispersed form.Solutions of palladium-dimethylglyoxime and palladium-salicylaldoxime in alkali hydroxide or ammonia are masked with respect to many reactions of the palladium as well as of the organic components. In alkaline solutions, when adding alkali cyanide, demasking occurs, with the deliberation of the innercomplex forming organic components. For the processes of dissolution and demasking appropriated equations are suggested.The demasking of dimethylglyoximc in alkaline solutions of palladium dimethylglyoxime permits a new sensitive test for cyanide ion. This cyanide test seems to be appropriate for the detection of illuminating gas.Palladium hydroxyquinorate is insoluble in solutions of alkali cyanides, though it is not precipitable from cyanide containing palladium solutions. An explanation for this “false equilibrium” is suggested.     

In situ generation of palladium oxide nano-crystals

Synthesis of metal–organic framework (MOF) based on tetra-pyridyl porphyrin and palladium (II) salt resulted in the formation of palladium oxide nano-crystals. The palladium oxide nano-crystals were characterized by PXRD, TEM, HRTEM, ED, UV–Vis spectroscopy, DLS, SEM and AFM. A plausible mechanism for the in situ generation of nano-crystals has been proposed.     

Interaction of CO with palladium supported on oxidized tungsten

A model catalyst system, palladium on tungsten oxide, has been examined by temperature-programmed desorption and photoemission spectroscopy. The samples were prepared by evaporation of palladium onto an oxidized tungsten foil under ultrahigh vacuum conditions. Mostly three-dimensional (3-D) palladium (Pd) clusters were found to be present on oxidized tungsten (WOx) surfaces at room temperature. Upon annealing to 670 K, the palladium clusters are redispersed and decorated by the WOx surface layer. The nature of the WOx phase on top of the palladium clusters is dependent on the mode of oxidation of the tungsten foil prior to palladium deposition. Mainly W(2+) species decorate palladium deposits on tungsten oxidized at room temperature, while mainly W(4+) species are on top of palladium deposits on the surface oxidized at 1300 K. The appearance of a Pd(n+)-O-W(4+) mixed oxide phase with n < 2 was observed on the oxidized tungsten surface. The substantial reduction (relative to nonannealed samples) of molecular CO coverage induced by annealing is discussed in terms of the changes in chemical composition and morphology of the outermost surface.     

Biogenous iron oxide-immobilized palladium catalyst for the solvent-free Suzuki–Miyaura coupling reaction

Iron oxide produced by iron-oxidizing bacteria, Leptothrix ochracea, (biogenous iron oxide: BIO) was used as a support for immobilized palladium catalysts with organic cross-linkers. Palladium immobilized on BIO bearing imidazolium chloride delivered the desired biaryl products in sufficient yields in the Suzuki–Miyaura coupling reactions under solvent-free conditions and could be reused several times without significant loss of catalytic activity. It is shown that BIO can be exploited as a useful support for immobilization of palladium and the BIO-immobilized palladium catalyst effectively promotes the solvent-free Suzuki–Miyaura coupling reactions.