TiO2纳米粒子包覆聚苯乙烯球的结晶性能与表面光电压特性

TiO2具有很高的光催化活性，同时TiO2纳米粒子具有耐酸碱和耐光化学腐蚀、低成本、无毒等性质，在许多领域引起广泛关注．据报道，TiO2的锐钛矿晶型比金红石晶型具有更好的光催化活性．由于金红石是TiO2的热力学稳定相，而锐钛矿是亚稳相，通常锐钛矿相在550-800℃温度范围内形成金红石相，从而降低其催化活性，限制了其应用．     

可见光激发下PtⅣClx /TiO2的光诱导电子转移研究

1998年, Kisch等[1]发现PtⅣ卤化物修饰的TiO2催化剂(PtⅣClx/TiO2)具有可见光活性, 他们认为PtⅣ卤化物作为光敏化物种, 能够将电子转移到TiO2导带, 催化剂的表面吸附氧捕获电子后生成氧自由基, 继而氧化降解成对氯苯酚. 但是, 由于PtⅣ卤化物及其激发态能级的不确定, 对其反应机理研究尚未见报道.     

Photoelectrochemical Character of TiO2 Nanocrystalline Electrodes Sensitized by Aluminum Phthalocyanines Modified with Sulfonate Groups

IntroductionIn recent years, dye-sensitized solar cells(DSSCs) have attracted more and more attention be-cause of their low cost and simple fabrication[1—3].They are made of four parts: a photo-electrode, a dyesensitizer, an electrolyte and a counter-ele…     

TiO2纳米粒子膜的表面态性质及其光催化活性的研究

TiO₂纳米粒子膜催化剂光催化降解水中污染物,与粉末相比具有可重复使用、易回收等优点,近年来,在光化学领域受到人们的高度重视^[1～3].膜催化剂的表面性质与其光催化活性直接相关,研究这些性质能够为研制、开发高效催化剂提供理论依据.本文采用TiCl₄水解法,制备了酸性、碱性条件下TiO₂纳米粒子膜.利用原子力显微镜(AFM)、X-射线衍射谱(XRD)、红外光谱(IR)和场诱导表面光电压谱(EFISPS)测定其表面微结构.考察了它们对苯酚降解的光催化活性,讨论了膜催化剂的表面性质对光催化活性的影响.     

卟啉/TiO2界面的相互作用研究

采用吸收光谱、荧光光谱和瞬态光伏技术研究了卟啉/TiO2体系的吸收光特性、荧光特性和光伏特性, 并研究了卟啉和TiO2之间的界面相互作用. 研究结果表明, 卟啉环在与钬原子结合前后与TiO2之间的作用不同, TiO2的粒径也影响界面的相互作用. 卟啉与粒径为10 nm的TiO2作用后, 能级发生了简并, 同时带隙发生了红移. 卟啉与粒径为56 nm的TiO2相互作用后只有特征吸收峰发生红移, 带隙和峰的数量几乎未发生变化. 这说明在粒径为10 nm的TiO2与卟啉的大π键之间出现了离域的相互作用, 这也被荧光光谱和瞬态光伏曲线所证实.     

Multivalency iodine doped TiO2: preparation, characterization, theoretical studies, and visible-light photocatalysis

Multivalency iodine (I(7)+/I(-)) doped TiO(2) were prepared via a combination of deposition-precipitation process and hydrothermal treatment. The as-prepared samples were characterized by X-ray diffraction, transmission electron microscopy, Brunauer-Emmett-Teller surface area, UV-vis diffuse reflectance spectra, X-ray photoelectron spectroscopy, surface photovoltage spectroscopy, and electric-field-induced surface photovoltage spectroscopy. The electronic structure calculations based on the density functional theory revealed that upon doping, new states that originated from the I atom of the IO(4) group are observed near the conduction-band bottom region of TiO(2), and the excitation from the valence band of TiO(2) to the surface IO(4-) is responsible for the visible-light response of the I-doped TiO(2). The as-prepared I-doped TiO(2) showed high efficiency for the photocatalytic decomposition of gaseous acetone under visible light irradiation (lambda > 420 nm). A possible mechanism for the photocatalysis on this multivalency iodine (I(7)+/I(-)) doped TiO(2) under visible light was also proposed.     

The nitrogen-boron paramagnetic center in visible light sensitized N-B co-doped TiO(2). Experimental and theoretical characterization

Nitrogen boron co-doped TiO(2) prepared via sol-gel synthesis and active under visible light, contains two types of paramagnetic extrinsic defects, both exhibiting a well resolved EPR spectrum. The first center is the well characterized [N(i)O]˙ species (i = interstitial) also present in N-doped TiO(2), while the second one involves both N and B. This latter center (labeled [NOB]˙) exhibits well resolved EPR spectra obtained using either (14)N or (15)N which show a high spin density in a N 2p orbital. The structure of the [NOB]˙ species is different from that previously proposed in the literature and is actually based on the presence of interstitial N and B atoms both bound to the same lattice oxygen ion. The interstitial B is also linked to two other lattice oxygen ions reproducing the trigonal planar structure typical of boron compounds. The energy level of the [NOB]˙ center lies near the edge of the valence band of TiO(2) and, as such, does not contribute to the visible light absorption. However, [NOB]˙ can easily trap one electron generating the [NOB](-) diamagnetic center which introduces a gap state at about 0.4 eV above the top of the valence band. This latter species can contribute to the visible light activity.     

掺钛熔石英TiO2—SiO2缺陷的ESCA研究

高纯熔石英中掺杂TiO_2可使其具有低热膨胀或无膨胀性及特殊的紫外吸收,以实现能量转换,提高红外发射率,因而对其结构研究已受到关注,我们曾用Raman光谱研究了其结构与光谱特性,本文用光电子能谱(ESCA)探讨不同TiO_2含量的熔石英中网络缺陷与钛的配位结构变化。     

金红石/锐钛矿混晶结构的TiO2薄膜光催化活性

采用磁控溅射法制备出一组金红石/锐钛矿混晶结构的纳米TiO2薄膜催化剂,并通过光催化降解苯酚实验考察该薄膜的催化性能. 光催化实验证明, 随着催化剂中金红石含量减少, 催化剂的光催化活性逐渐提高. X射线衍射(XRD)、X射线光电子能谱(XPS)、表面光电压谱(SPS)和原子力显微镜(AFM)结果表明, 催化剂为金红石和锐钛矿混晶结构, 并随着金红石含量减少, 催化剂的表面羟基(OH)和桥氧(—O—)的含量逐渐增加, 而且费米能级逐渐提高. 表面羟基和桥氧是有利于光催化的“活性物种”; 费米能级的提高使TiO2/H2O 面处TiO2的表面带弯增大, 导致了价带光生空穴参加光催化反应的几率增大, 有效地促进了光生载流子的分离; 这些因素是催化剂光催化活性逐渐提高的主要原因.     

TiO2纳米粒子膜的制备、表面态性质和光催化活性

在酸性和碱性条件下,用TiCl4水解法制备了TiO2纳米粒子膜催化剂.采用原子力显微镜(AFM),X射线衍射(XRD),表面光电压谱(SPS)和场诱导表面光电压谱(EFISPS)测定了催化剂表面的微结构及能级结构.对催化剂进行了光催化降解苯酚实验,测定了其光催化活性.结果表明,酸性条件下制备的TiO2膜催化剂的光催化活性较高,其结果接近于P25.用能带理论解释了TiO2纳米粒子膜催化剂光催化活性的差异,分析了膜厚对光催化活性的影响.     

TiO2表面氧空位对Rup2P/TiO2/ITO薄膜电极光致电荷转移的影响

采用改性的TiCl4水解法制备出三种不同表面性质的TiO2-X(X=5,10,20,X表示加入NaOH的浓度,单位为mo·lL-1)样品.利用(1,10-邻菲咯啉)2-2-(2-吡啶基)苯咪唑钌混配配合物(Rup2P)作为敏化剂,制备出Rup2P/TiO2-5/ITO(铟锡金属氧化物)、Rup2P/TiO2-10/ITO和Rup2P/TiO2-20/ITO表面敏化薄膜电极.测试结果表明三种薄膜电极的光电转换效率Rup2P/TiO2-10/ITO最高,Rup2P/TiO2-20/ITO次之,Rup2P/TiO2-5/ITO最低.利用吸收光谱、表面光电压(SP)谱、荧光光谱和表面光电流作用谱等分析了Rup2P和三种TiO2的能带结构和表面性质;利用光致循环伏安和表面光电流作用谱研究了三种Rup2P/TiO2-X/ITO薄膜电极的光致界面电荷转移过程.结果表明,在光致界面电荷转移过程中,TiO2层表面氧空位对Rup2P/TiO2-X/ITO薄膜电极光致电荷转移产生重要影响.并进一步讨论了Rup2P/TiO2-X/ITO薄膜电极的光电流产生机理.     

Rup_2P表面敏化TiO_2基复合薄膜光致界面电荷转移

采用离子束溅射技术制备出TiO2/ITO、Zn2+掺杂的TiO2(TiO2-Zn)/ITO和TiO2/ZnO/ITO薄膜,采用表面敏化技术和旋转涂膜法,制备出(1,10-邻菲咯啉)2-2-(2-吡啶基)苯咪唑钌混配配合物(Rup2P)表面敏化的TiO2基复合薄膜Rup2P/TiO2/ITO、Rup2P/TiO2-Zn/ITO和Rup2P/TiO2/ZnO/ITO.表面光电压谱(SPS)结果发现:敏化后的TiO2基薄膜在可见区(400-600nm)产生SPS响应;TiO2基薄膜的能带结构不同,其在400-600nm和350nm处的SPS响应的峰高比不同.利用电场诱导表面光电压谱(EFISPS),测定TiO2基薄膜和表面敏化TiO2基复合薄膜各种物理参数,并确定其能带结构.分析可知,表面敏化TiO2基复合薄膜在400-600nm的SPS响应峰主要源于Rup2P分子的中心离子Ru4d能级到配体1,10-邻菲咯啉π*1和2-(2-吡啶基)苯咪唑π*2能级的跃迁;TiO2中Zn2+掺杂能级有利于Ru4d能级到配体π*1和π*2跃迁的光生电子向TiO2-Zn导带的注入;TiO2/ZnO异质结构有利于光生电子向ITO表面的转移,从而导致可见光(400-600nm)SPS响应增强以及光电转换效率的提高.     

Rutile TiO2 nanowires on anatase TiO2 nanofibers: a branched heterostructured photocatalysts via interface-assisted fabrication approach

A water-dichloromethane interface-assisted hydrothermal method was employed to grow rutile TiO(2) nanowires (NWs) on electrospun anatase TiO(2) nanofibers (NFs), using highly reactive TiCl(4) as precursor. The water-dichloromethane interface inhibited the formation of rutile NWs in water phase, but promoted the selective radial growth of densely packed rutile NWs on anatase NFs to form a branched heterojunction. The density and length of rutile NWs could be readily controlled by varying reaction parameters. A formation mechanism for the branched heterojunction was proposed which involved (1) the entrapment of rutile precursor nanoparticles at water-dichloromethane interface, (2) the growth of rutile NWs on anatase NFs via Ostwald ripening through the scavengering of interface-entrapped rutile nanoparticles. The heterojunction formed at anatase NF and rutile NW enhanced the charge separation of both under ultraviolet excitation, as evidenced by photoluminescence and surface photovoltage spectra. The branched TiO(2) heterostructures showed higher photocatalytic activity in degradation of rodamine B dye solution than anatase NFs, and the mixture of anatase NFs, and P25 powders, which was discussed in terms of the synergistic effect of enhanced charge separation by anatase-rutile heterojunction, high activity of rutile NWs, and increased specific area of branched heterostructures.     

Effect of additives on the photovoltaic performance of coumarin-dye-sensitized nanocrystalline TiO2 solar cells

The effects of deoxycholic acid (DCA) and 4-tert-butylpyridine (TBP) as additives on the photovoltaic performance of coumarin-dye-sensitized nanocrystalline TiO2 solar cells were investigated. DCA coadsorption improved both the photocurrent and photovoltage of the solar cells, even though it decreased the amount of dye adsorbed on the TiO2 electrode. The improved photocurrent may arise from suppression of the deactivation of the excited state via quenching processes between dye molecules or a more negative LUMO level of the dye in the presence of DCA, resulting in a high electron-injection yield from the dye into TiO2. The increased photovoltage is probably due to suppression of recombination between the injected electrons and I3- ions on the TiO2 surface (dark current). The addition of TBP to the electrolyte also markedly improved the photovoltage and fill factor of the solar cell, and consequently, the total conversion efficiency increased from 3.6% to 7.5%. FT-IR spectroscopy indicated that a large amount of TBP was adsorbed on the dye-coated TiO2 films in the presence of Li cations. This result suggests that TBP, like DCA, suppressed the dark current on the TiO2 surface, which resulted in the improved photovoltage.     

Spectroscopic study for photocatalytic decomposition of organic compounds on titanium dioxide containing sulfur under visible light irradiation

Yellowish S-containing TiO2 (S-TiO2) powders were prepared by calcination of a mixture of titanium(III) chloride and ammonium thiocyanate solutions. Three kinds of S-TiO2 were prepared by varying the concentration of ammonium thiocyanate (0.5, 1 or 13 M). X-ray photoelectron spectroscopy spectra of the S-TiO2 showed that sulfur atoms existed on the surface of TiO2 powders. But the peaks assigned to S disappeared after Ar+ etching, which means that these atoms were not doped in the bulk of the TiO2 powders. While UV-visible absorption spectra of S-TiO2 showed that the absorption edges of these photocatalysts were seen to shift to a longer wavelength (lower band gap energy) than those of undoped rutile TiO2 prepared and commercial anatase type TiO2 (ST-01). The S-TiO2 (1 M) exhibited higher photocatalytic activity than ST-01 for degradation of methylene blue in aqueous solution under visible light irradiation (lambda > 400 nm). It was also confirmed by IR spectroscopy that acetaldehyde in oxygen under visible light irradiation (lambda > 400 nm) was decomposed to acetic acid by the S-TiO2 and ST-01 at the first decomposition step.     

氮掺杂TiO2纳米管阵列的制备及其可见光光电催化活性研究

联用电化学阳极氧化和湿化学法制备氮掺杂的TiO2纳米管阵列膜.应用SEM、XPS、DRS分析、表征,并研究该膜层的形貌、组成和光学性质以及在卤钨灯照射下降解甲基橙水溶液的光电催化活性.结果表明:氮以取代掺杂的形式进入TiO2晶格,掺氮的TiO2纳米管阵列在可见光区有较强的吸收,其光电催化性能优于纯的TiO2纳米管阵列膜.     

Dye-sensitized solar cells based on TiO2-B nanobelt/TiO2 nanoparticle sandwich-type photoelectrodes with controllable nanobelt length

The TiO(2)-B nanobelt (NB)/TiO(2) nanoparticle (NP) sandwich-type structure photoelectrode, with controllable nanobelt length, has been used to fabricate high-efficiency dye-sensitized solar cells (DSSCs), which combine the advantages of the rapid electron transport in TiO(2)-B NBs and the high surface area of TiO(2) NPs. The results indicate that the sandwich-type photoelectrode achieves higher photoelectrical conversion efficiency when compared with the TiO(2) nanoparticulate electrode. Increasing the length of TiO(2)-B NBs has been demonstrated to improve the photoelectric conversion efficiency (η). DSSCs with the longest (10 μm) TiO(2)-B NBs yield the highest η of 7.94%. The interfacial electron transport of DSSCs with different lengths of TiO(2)-B NBs has been quantitatively investigated using the photovoltage transient and the electrochemical impedance spectra, which demonstrates that the DSSCs with longest TiO(2)-B NBs display the highest electron collection efficiency and the fastest interfacial electron transfer.     

TiO2纳米带表面光伏特性的研究

近年来, 一维结构的纳米带由于其不同于管、线材料的新颖结构以及独特的光电性能而受到广泛关注. 人们通过各种方法合成了氧化锌、硫化镉和氧化锡等纳米带材料[1,2]. 纳米TiO2以其优异的光电性能和高的化学稳定性而被广泛应用于太阳能电池、光催化降解等诸多领域[3], 从而成为研究热点, 最近其纳米带的制备也有报道[4].     

A simple route for the preparation of Eu, N-codoped TiO2 nanoparticles with enhanced visible light-induced photocatalytic activity

A simple route has been developed for the synthesis of europium, nitrogen-codoped titania photocatalysts under mild conditions (i.e., low temperature, < or = 348 K, and ambient pressure). The as-prepared photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and diffuse reflectance spectra (DRS) analyses. The results showed that the codoped photocatalyst with a spheroidal shape exhibited a smaller size than the undoped titania. The transformation from anatase to rutile was suppressed by doping with Eu and N atoms. Furthermore, the absorbance spectra of Eu, N-codoped TiO(2) exhibited a significant red shift to the visible region. The photocatalytic activity of Eu, N-codoped TiO(2) was evaluated by photodegradation of the dye reactive brilliant red X-3B under visible light. This codoped sample exhibited enhanced photocatalytic activity compared to N-doped TiO(2), pure TiO(2), and P25.     

Synthesis of LaVO4/TiO2 heterojunction nanotubes by sol-gel coupled with hydrothermal method for photocatalytic air purification

With the aim of improving the effective utilization of visible light, the LaVO(4)/TiO(2) heterojunction nanotubes were fabricated by sol-gel coupled with hydrothermal method. The photocatalytic ability was demonstrated through catalytic removal of gaseous toluene species. The nanotube samples were characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), surface photovoltage (SPV), Raman spectra and N(2) adsorption-desorption measurements. The characterization results showed that the samples with high specific surface areas were of typical nanotubular morphology, which would lead to the high separation and transfer efficiency of photo induced electron-hole pairs. The as-prepared nanotubes exhibited high photocatalytic activity in decomposing toluene species under visible light irradiation with fine photochemical stability. The enhanced photocatalytic performance of LaVO(4)/TiO(2) nanotubes might be attributed to the matching band potentials, the interconnected heterojunction of LaVO(4) versus TiO(2), and the large specific surface areas of nanotubes.