Structural,morphological and mechanical properties of laser-irradiated copper using continuous wave diode laser

Laser irradiation effects on morphological, structural and mechanical properties of copper are explored. The targets are exposed by employing low-cost continuous wave (CW) laser (wavelength of 532?nm) in air. The surface morphology, structural and mechanical modification of irradiated targets was investigated by scanning electron microscopy (SEM) (Fei, Quanta 250), an X-ray diffractrometer (XRD) (DMAX III ARigaku, Japan) and a Vickers hardness tester, respectively. The SEM analysis revealed the exfoliation sputtering, electronic sputtering, thermal stresses and cracks. The grain size, dislocation line density, relative intensity and d-spacing of irradiated metals were studied by XRD. Micro hardness is found to increase with the increase in time of laser irradiation, in accordance with the Vickers hardness tester. This work provides a cost-effective, user-friendly and easy-to-handle study of several properties of irradiated targets with good results.     

Structural and optical properties of laser irradiated nano structured cadmium oxide thin film synthesized by sol-gel spin coating method

Cadmium oxide CdO nanostructured thin films are synthesized using sol-gel spin coating method. The prepared samples of CdO thin films are irradiated with 10 mJ laser from pulsed Q-Switched Nd:YAG laser at 1064 and 532 nm wavelength. The samples were exposed to 45 pulses of 7 ns pulse duration. Morphology and structural analysis were carried out with scanning electron microscope (SEM) micrographs and X-ray diffraction (XRD) patterns. Optical investigations were obtained with spectrometer and fluorospectrometer from Shimadzu. SEM micrographs confirm the nanostructure of the CdO film and indicate agglomeration of nanoparticles with laser irradiation. XRD patterns show decrease in the intensity of orientation peaks after laser irradiation. Variation in band gap energy, absorption peaks, and photoluminescence spectra with laser irradiation are observed.     

磁场辅助激光熔覆制备Ni60CuMoW复合涂层

采用磁场辅助激光熔覆技术,在Q235钢表面制备了Ni60CuMoW复合涂层,借助SEM,EDS 和XRD 等表征手段对涂层进行了微观组织和物相分析,利用维氏硬度计测试了复合涂层截面的显微硬度分布,通过摩擦磨损实验和电化学测试系统研究了复合涂层的磨损性能和耐腐蚀性能。研究结果表明:涂层主要由-Ni,Cu）固溶体、硅化物和硼化物组成,Cr3Si晶粒细化且均匀致密;磁场辅助作用下,激光熔覆涂层平均显微硬度达到913HV0.5,为无磁场辅助涂层的1.5 倍,磨损失重仅为无磁场涂层的36%,自腐蚀电位上升了100 mV,腐蚀电流密度降低了70%,耐磨耐蚀性能得到了显著改善。     

Effect of fluence and ambient environment on the surface and structural modification of femtosecond laser irradiated Ti

Under certain conditions, ultrafast pulsed laser interaction with matter leads to the formation of self-organized conical as well as periodic surface structures(commonly reffered to as, laser induced periodic surface structures, LIPSS). The purpose of the present investigations is to explore the effect of fsec laser fluence and ambient environments(Vacuum O_2) on the formation of LIPSS and conical structures on the Ti surface. The surface morphology was investigated by scanning electron microscope(SEM). The ablation threshold with single and multiple(N = 100) shots and the existence of an incubation effect was demonstrated by SEM investigations for both the vacuum and the O_2 environment. The phase analysis and chemical composition of the exposed targets were performed by x-ray diffraction(XRD) and energy dispersive x-ray spectroscopy(EDS), respectively. SEM investigations reveal the formation of LIPSS(nano micro). FFT d-spacing calculations illustrate the dependence of periodicity on the fluence and ambient environment. The periodicity of nano-scale LIPSS is higher in the case of irradiation under vacuum conditions as compared to O_2. Furthermore, the O2 environment reduces the ablation threshold. XRD data reveal that for the O_2 environment, new phases(oxides of Ti) are formed. EDS analysis exhibits that after irradiation under vacuum conditions, the percentage of impurity element(Al) is reduced. The irradiation in the O_2 environment results in 15% atomic diffusion of oxygen.     

高压和热处理对铝青铜微观组织的影响

 借助金相、扫描电子显微镜（SEM）/能谱仪（EDS）及X射线衍射（XRD）等方法,研究了高压和热处理对铝青铜微观组织的影响。结果表明：铝青铜经750 ℃温度、6 GPa压力处理后所获得的α相的晶粒尺寸较经750 ℃温度、常压处理后所获得的α相晶粒尺寸小;当铝青铜经高压处理后再经750 ℃保温2 min常压处理时,组织中出现细条状的α相,且热处理后的冷却速度越大,细条状α相的数量越多,颗粒状α相的数量越少。     

Morphological and structural characterizations of different oxides formed on the stainless steel by Nd:YAG pulsed laser irradiation

The effects of laser surface irradiation on microstructure of AISI 304 stainless steel were investigated. The stainless steel surface was characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). XRD patterns indicated that different oxides, such as chromium oxides and manganese oxides were fabricated successfully on the surface of the stainless steel by Nd:YAG pulsed laser irradiation. The effects of the growth conditions such as the laser power density on the morphologies of the different oxides have been investigated. From the FESEM, EDS (energy-dispersive spectrum) and TEM observations, the oxides with triangle-like, quadrangular and hexagonal morphologies have been fabricated successfully. The XPS was used to verify the formed oxides which had been detected by the XRD patterns. It was considered that laser power density had a critical role in the formation of different oxides.     

Dispersion of laser droplets using H+ ions and annealing effect on pulsed laser deposited nickel ferrite thin films

Nickel ferrite thin films were deposited by a pulsed laser deposition (PLD) technique on silicon substrate at room temperature in a vacuum of 5×10⁻⁵ mbar. The films were subjected to different annealing temperatures from 300–900°C and were also exposed to single shot energetic hydrogen ions using a Dense Plasma Focus (DPF) device. The changes induced in the films exposed at different distances from the top of the anode were investigated. The structural, morphological and magnetic properties of the annealed and exposed samples were investigated. X-ray diffraction (XRD) studies reveal the presence of a single phase of nickel ferrite after annealing. SEM micrographs indicate an increase in the grain size, both on annealing as well as on exposure to hydrogen ions. Annealing and hydrogen ion irradiation induced an enhancement in the magnetic moments. Laser droplets which are inherent in films deposited by laser ablation were found to be dispersed as a result of single shot hydrogen ion irradiation from the DPF.     

Influence of 120 MeV Si9+ ion irradiation on ZnTe semiconductor thin films

ABSTRACT

ZnTe (Zinc Telluride) is a potential semiconducting material for many optoelectronic devices like solar cells and back contact material for CdTe-based solar cells. In the present study, ZnTe thin films were prepared by thermal evaporation technique and then irradiated with 120?MeV Si⁹⁺ ions at different fluences. These films are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV–Visible spectroscopy techniques. XRD study confirms increased crystallinity and grain growth for post-irradiated ZnTe thin films for fluences, up to 1?×?10¹¹ ions cm^?2. However, the grain size and crystallinity decreased for higher fluence-exposed samples. SEM images confirm the observed structural properties. Modification of the surface morphology of the film due to the ion irradiation with different fluences is studied. Optical band gap of film is decreased from 2.31?eV (pristine) to 2.17?eV after irradiation of Si⁹⁺ ions.     

Effect of complex inter-site couplings on the excitation energy transfer in the FMO complex

The laser irradiation effects on surface, structural and mechanical properties of zirconium (Zr) have been investigated. For this purpose, Zr samples were irradiated with Excimer (KrF) laser (λ ≈ 248 nm, τ ≈ 18 ns, repetition rate ≈ 30 Hz). The irradiation was performed under the ambient environment of oxygen gas at filling pressure of 20 torr by varying laser fluences ranging from 3.8 to 5.1 cm^-2. The surface and structural modification of irradiated targets was investigated by scanning electron microscope (SEM) and X-ray diffractometer (XRD). In order to explore the mechanical properties of irradiated Zr, the tensile testing and Vickers micro hardness testing techniques were employed. SEM analysis reveals the grain growth on the irradiated Zr surfaces for all fluences. However, the largest sized grains are grown for the lowest fluence of 3.8 J cm^?2. With increasing fluence from 4.3 to 5.1 J cm^?2, the compactness and density of grains increase whereas their size decreases. XRD analysis reveals the appearance of new phases of ZrO₂ and Zr₃O. The variation in the peak intensity is observed to be anomalous whereas decreasing trend in the crystallite size and residual stresses has been observed with increasing fluence. Micro hardness analysis reveals the increasing trend in surface hardness with increasing fluence. The tensile testing exhibits the increasing trend of yield stress (YS), decreasing trend of percentage elongation and anomalous behaviour of ultimate tensile strength with increasing fluence.     

化学沉淀法制备硒化铅薄膜

采用化学沉淀的方法沉淀PbSe薄膜,分别加入缓冲剂联氨(方法A)和碘化钾(方法B)。对反应原理进行了分析,对制备过程进行了优化,分别制备出了高质量的PbSe薄膜。采用XRD、SEM、EDS以及红外光谱测试对所制备样品进行了分析。结果表明,两种方法制备均为PbSe多晶薄膜,方法A制备薄膜结晶质量更好,择优生长方向明显;薄膜颗粒度、表面粗糙度都小于方法B;两种薄膜的Pb元素与Se元素比例接近化学计量比,方法B含有少量I元素;两种方法制备样品的吸收边相对带边跃迁都发生蓝移。     

The generation,detection and measurement of laser-induced carbon plasma ions and their implantation effects on brass substrate

The generation, detection and measurement of laser-induced carbon plasma ions and their implantation effects on brass substrate have been investigated. Thomson parabola technique was employed to measure the energy and flux of carbon ions. The magnetic field of strength 80?mT was applied on the graphite plasma plume to provide an appropriate trajectory to the generated ions. The energy of carbon ions is 678?KeV for laser fluence of 5.1?J/cm² which was kept constant for all exposures. The flux of ions varies from 32?×?10¹¹ to 72?×?10¹⁴?ions/cm² for varying numbers of laser pulses from 3000 to 12,000. In order to explore the ion irradiation effects on brass, four brass substrates were irradiated by carbon ions of different flux. Scanning electron microscope (SEM) and X-ray diffractometer (XRD) are used to analyze the surface morphology and crystallographic structure of ion-implanted brass, respectively. SEM analysis reveals the formation and growth of nano-/micro-sized cavities, pores and pits for the various ion flux for varying numbers of laser pulses from 3000 to 12,000. By increasing ion flux by increasing the number of pulses up to 9000 shots, the dendritic structures initiate to grow along with cavities and pores. At the maximum ion flux for 12,000 shots, the unequiaxed dendritic structures become distinct and the distance between the dendrites is decreased, whereas cavities, pores and pits are completely finished. The XRD analysis reveals that a new phase of ZnC (0012) is formed in the brass substrate after ion implantation. Universal tensile testing machine and Vickers microhardness tester are used to explore the yield stress, ultimate tensile strength and microhardness of ion-implanted brass substrate. The mechanical properties monotonically increase by increasing the ion flux. Variations in mechanical properties are correlated with surface and structural modifications of brass.     

X-ray evidence for the absence of 90°-domains in polycrystalline PbTiO3 thin films with grains below a critical size

3 thin films is systematically studied by using X-ray diffraction (XRD). The PbTiO₃ thin films with different average grain sizes were prepared on various substrates by a sol-gel process. The films on NaCl and fused glass are randomly grain-oriented, while those on (111)Pt/Ti/SiO₂/Si are highly {100} cubic index grain-oriented . It is found from the XRD patterns of the films on NaCl that with decreasing average grain size from 230 to 80 nm, the intensities of high h index (h>l) peaks (hkl), such as (100), (110), (200), (201), (210), (211), etc., decrease rapidly and ultimately disappear, whereas another set of peaks (lkh), including (001), (002), (102), (112), etc., are still intense. This interesting result suggests that at grain size below a certain critical size an increasing number of grains no longer show 90°-domains, which is confirmed by TEM observations. Meanwhile, X-ray evidence of such a grain-size-related absence of 90°-domains is also found for PbTiO₃ films on Pt(111) and fused-glass substrates. The volume fractions of single-domain grains (without 90°-domains) in the films are estimated from their XRD patterns. By combining SEM and TEM investigations, the critical grain size for the formation of 90°-domains is further determined to be near 200 nm. Received: 19 December 1996/Accepted: 24 March 1997     

Thickness effect on the evolution of morphology and optical properties of ZnO films

N-Al co-doped ZnO films with various thicknesses were deposited on glass substrates by ultrasonic spray pyrolysis (USP). The crystalline microstructure, morphology, distribution of elements and photoluminescence properties of ZnO films were characterized by X-ray diffraction (XRD), field emission scanning microscopy (FESEM), energy dispersive X-ray spectroscopy (EDS) and photoluminescence (PL) spectroscopy. The XRD and FESEM results show that with the increase of film thickness the grain size increases and the grain shape changes from regular hexagonal sheet-like to wedge-shaped, even pyramidal. The PL spectra illustrate that there is an obvious red-shift for the emission center from ultraviolet to blue region, and the intensities of defects emissions increase with the increase of thickness. In addition, the electrical properties are proved to be strongly affected by film thickness.     

Proof‐of‐Concept Studies Directed toward the Formation of Metallic Ag Nanostructures from Ag3PO4 Induced by Electron Beam and Femtosecond Laser

In this work, for the first time, the instantaneous nucleation and growth processes of Ag nanoparticles on Ag₃PO₄ mediated by femtosecond laser pulses are reported and analyzed. The investigated samples are pure Ag₃PO₄ sample, electron‐irradiated Ag₃PO₄ sample, and laser‐irradiated sample. Complete characterization of the samples is performed using X‐ray diffraction (XRD), Rietveld refinements, field emission scanning electron microscopy, and energy dispersive spectroscopy (EDS). XRD confirms that the irradiated surface layer remains crystalline, and according to EDS analysis, the surface particles are composed primarily of Ag nanoparticles. This method not only offers a one‐step route to synthesize Ag nanoparticles using laser‐assisted irradiation with particle size control, but also reports a complex process involving the formation and subsequent growth of Ag nanoparticles through an unexpected additive‐free in situ fabrication process.     

Laser radiation effects on optical and structural properties of nanostructure CdSe thin film

Cadmium selenide (CdSe) thin films were deposited on a glass substrate using the thermal evaporation method at room temperature. The changes in the optical properties (optical band gap and absorption coefficient) after irradiation by TEA N₂ laser at different energies were measured in the wavelength range 190–800 nm using a spectrophotometer. It was found that the optical band gap is decreased after irradiating the thin films. The samples were characterized using X-ray diffraction (XRD), and the grain size of the CdSe thin film was calculated from XRD data, which was found to be 41.47 nm as-deposited. It was also found that grain size increases with laser exposure. The samples were characterized using a scanning electron microscope and it was found that big clusters were formed after irradiation by TEA N₂ laser.     

Laser irradiation effects on gold

Investigations on the laser irradiation effects on gold are explored in terms of plasma-plume dynamics and morphological and crystallographic changes. Annealed 4N gold samples were irradiated with a Q-switched Nd:YAG laser (53 mJ, 21 MW, 532 nm, and pulse width 6–8 ns) for plume dynamics using 10-ns gated fast photography. A Q-switched pulsed Nd:YAG laser (10 mJ, 1.1 MW, 1064 nm, and pulse width 9 ns) was used to irradiate the surface of the samples for morphological and crystallographic studies of laser-irradiated gold in a vacuum ～10^?3 Torr. The annealed samples were exposed to 50 shots of a Nd:YAG laser (10 mJ, 1.1 MW, 1064 nm, and pulse width 9 ns). The investigation on the plume was done by using an intensified charged-couple device ICCD-5760/IR-UV camera. The morphological investigation of the irradiated surface was carried out by analyzing micrographs obtained using an Hitachi S 3000 H scanning-electron microscope (SEM). The crystallographic studies of the irradiated samples were performed by analyzing the XRD patterns obtained using an X’ Pert Pro Pan Analytical X-ray diffractometer. The investigation on gated ICCD images of the plume reveal that, at very earlier times, the plasma-plume expansion has a linear trend, whereas, at later times, the plasma-plume expansion is nonuniform. SEM micrographs exhibit the primary mechanisms of pulsed-laser ablation (PLA), such as hydrodynamic sputtering, thermal sputtering, exfoliation sputtering, and splashing. The surface morphology was explained in terms of crater formation, swelling, burning, nucleation, grain growth, and nonsymmetric heat conduction. The nonuniform thermal expansion of gold due to thermal-energy transfer is also studied by SEM micrographs, which was supported by XRD analysis. The structural analysis on the basis of XRD shows that the composition of the irradiated samples is not disturbed even after laser irradiation. The grain sizes also changed due to laser irradiation.     

Effects of Nd:YAG laser irradiation on structural, morphological, cation distribution and magnetic properties of nanocrystalline CoFe2O4

The cobalt ferrite nanoparticles of 20 nm size were synthesized by sol-gel auto-combustion technique. The samples were irradiated with Nd:YAG laser to understand the effects of irradiation on structural, cation distribution and magnetic properties. The virgin and irradiated samples were characterized by X-ray diffraction technique. The X-ray diffraction studies at room temperature shows that defects were created in the lattice after irradiation which causes effects on structural, cation distribution and magnetic properties. The energy dispersive analysis of X-rays (EDAX) showed the chemical composition is as per the expected stichiometry. The lattice constant observed from XRD data for virgin and irradiated samples shows increasing trend after irradiation. Cation distribution was investigated by using X-ray diffraction method. We observe decrease in magnetization of the samples after irradiation. The observed reduction in the saturation magnetization after irradiation can be understood on the basis of the partial formation of paramagnetic centers and rearrangement of cations in the lattice.     

Laser irradiation effects on the surface,structural and mechanical properties of Al–Cu alloy 2024

Laser irradiation effects on surface, structural and mechanical properties of Al–Cu–Mg alloy (Al–Cu alloy 2024) have been investigated. The specimens were irradiated for various fluences ranging from 3.8 to 5.5 J/cm² using an Excimer (KrF) laser (248 nm, 18 ns, 30 Hz) under vacuum environment. The surface and structural modifications of the irradiated targets have been investigated by scanning electron microscope (SEM) and X-ray diffractometer (XRD), respectively. SEM analysis reveals the formation of micro-sized craters along the growth of periodic surface structures (ripples) at their peripheries. The size of the craters initially increases and then decreases by increasing the laser fluence. XRD analysis shows an anomalous trend in the peak intensity and crystallite size of the specimen irradiated for various fluences. A universal tensile testing machine and Vickers microhardness tester were employed in order to investigate the mechanical properties of the irradiated targets. The changes in yield strength, ultimate tensile strength and microhardness were found to be anomalous with increasing laser fluences. The changes in the surface and structural properties of Al–Cu alloy 2024 after laser irradiation have been associated with the changes in mechanical properties.     

A study on CoFe/p-Si interfacial structures before and after swift heavy ion irradiation

Interfacial structures of CoFe/p-Si have been studied before and after the swift heavy ion (～100?MeV, Ni⁷⁺) irradiation to investigate its electronic and magnetic behavior. X-ray diffraction (XRD), atomic force microscopy, magnetic force microscopy and magnetization characteristics (M–H) from vibrating sample magnetometer (VSM) techniques have been used for the above. XRD data have confirmed the formation of the CoFe alloy phase along with the silicide phases of Fe and Co. It is observed that there is an irradiation-induced growth in crystallite but surface remains smooth with a surface roughness of ～34?nm. A very significant increase has been observed in the magnetization and that too with irradiation dose as compared with unirradiated ones, maintaining their superparamagnetic behavior. The results could be understood due to the role played by various magnetic phases in the structure. The magnetic field sensitivity on electronic transport across the structures has also increased in a significant manner after the irradiation as compared with unirradiated ones. The magnetic field sensitivity has resulted in an MR of 20%. The results could be understood due to the irradiation induced interfacial intermixing to result in increased magnetic phases of silicide for the observed significant magnetic behavior on the irradiation.     

Combining TEM and APFIM techniques to study the microstructure of steels and hardmetals

This paper describes the benefits of combining transmission electron microscopy (TEM) and atom probe field ion microscopy (APFIM) techniques to study the microstructure of steels and hardmetals. In addition to energy dispersive X-ray spectrometry (EDS), recent experience of electron energy loss spectroscopy (EELS) and energy filtered TEM (EFTEM) is treated. Topics covered are: phase composition (APFIM, TEM/EDS and TEM/EELS); precipitate size distribution (EFTEM); precipitate volume fraction (APFIM); and compositional gradients (APFIM, EFTEM and SEM). Examples given include precipitate composition and size distribution in creep resistant 9–12% chromium steels, phase distribution and composition in nitrogen containing hardmetals (cermets) after sintering and heat treatment, and boron grain boundary segregation in austenitic stainless steels.