Effect of pH on Poly(acrylic acid) Solution Polymerization

The free-radical redox-initiated aqueous solution polymerization of fully and partially neutralized acrylic acid was carried out at room temperature under full exposure to air. The effect of neutralization degree on the polymerization rate and product properties was studied. Increasing neutralization of the reaction mixture with sodium hydroxide resulted in greater conversion of acrylic acid to sodium acrylate. The rate of polymerization, determined from a gravimetric off-line water removal technique, was shown to decrease significantly with decreasing degree of neutralization. Molecular weight also decreased with decreasing degree of neutralization. The glass transition temperature and hydrophilicity of the polymer product decreased with increasing degree of neutralization. In-line infrared monitoring was also used to monitor the reaction progress and was shown to be an effective tool for this purpose.     

辉光放电电解等离子体引发合成聚丙烯酸钠/腐植酸复合高吸水性树脂

以丙烯酸和腐植酸为原料,N,N-亚甲基双丙烯酰胺为交联剂,在水溶液中采用辉光放电电解等离子体引发聚合反应制备聚丙烯酸钠/腐植酸复合高吸水性树脂。 考察了放电电压、交联剂、丙烯酸中和度、后聚合温度、腐植酸钠和丙烯酸的含量对树脂吸水率的影响,讨论了树脂在0.9%氯化钠溶液中的溶胀速率和不同pH值溶液中的溶胀行为。 用红外光谱和热重分析分别对产物进行了结构表征和稳定性测试,结果表明,最佳的合成条件为：放电电压470 V、交联剂质量分数为0.6%、腐植酸钠质量分数为4%、丙烯酸质量分数为10%、中和度60%、后聚合温度70 ℃。 所得复合树脂对蒸馏水的吸水率为1152 g/g,对0.9%NaCl溶液的吸水率为89 g/g,800 ℃后复合树脂残留率为44.3%。     

丙烯酸-丙烯酸钠共聚物在水溶液中的离解

聚丙烯酸和聚丙烯酸盐是一类重要的水溶性聚合物,也是典型的聚电解质的代表．聚电解质在溶液中可以离解为聚离子和对离子,这一行为是它的根本特性．聚电解质的离解行为与相应的小分子．弱酸和弱酸强碱所生成的盐的离解行为有很大的不同,从而引发了许多实验和理论的研究.早期的工作,大都是用电位滴定的方法研究酸性聚电解质的离解,     

Research on various factors influencing the moisture absorption property of sodium polyacrylate

Sodium polyacrylate was synthesized with acrylic acid as the monomer, and sodium bisulfate and ammonium persulfate as the initiator, by means of aqueous solution polymerization. The factors influencing the properties of moisture absorption, such as monomer concentration, dosage of initiator, and reaction temperature were systematically investigated. The experimental results indicate that the moisture-absorbing property of this polymer was better than other traditional material, such as silica gel, and molecular sieve. The best reaction condition and formula are based on the orthogonal experiment design. The optimum moisture absorbency of sodium polyacrylate reaches 1.01 g/g. The mathematical correlation of this polymer with various factors and moisture absorbency is obtained based on the multiple regression analysis. The moisture content intuitive analysis table shows that neutralization degree has the most significant influence on moisture absorbency, followed by monomer concentration and reaction temperature, while other factors have less influence. Supported by the 863 Project (Grant No. 2005AA001650)     

Surfactant-modified polypropylene as a catalyst for oxidation of mercaptans

Surface modification of polypropylene by soluble metallophthalocyanine was performed. The effect of pretreatment of polypropylene on the degree of surface anchoring of the macrocycle was shown. The catalytic activity of the hybrid materials produced in the oxidation reaction of sodium diethyldithiocarbamate was determined.     

聚苯乙烯磺酸钠与阳离子表面活性剂的相互作用和纳米聚集体的生成

在聚苯乙烯磺酸钠(PSS)的水溶液中,引入阳离子表面活性剂(CTAB或DDAB)使与PSS通过静电相互作用实现聚苯乙烯磺酸盐不同程度的中性化,并进而对PSS/表面活性剂复合物在水中的行为特征、特别是PSS因疏水化而产生的聚集行为以及临界聚集浓度等采用多种方法如溶液的透光率;荧光光谱;荧光探针以及扫描电镜观察等进行了研究,得到一些颇为有趣的结果.结果表明PSS-CTAB或DDAB加成物可自发的形成约70 nm的纳米粒子。而中性化程度则对加成物的构型以及体系的透光率等有较大影响。结果还表明所得具有亲水外壳和疏松的疏水内核的聚集体能容易的使疏水分子进入其中。     

苯乙烯-苯乙烯磺酸钠共聚物的制备及其流变性能

采用乳液聚合合成了一种可作为聚丙烯(PP)纤维可染改性添加剂的苯乙烯-苯乙烯磺酸钠共聚物P(St-co-NaSS)。通过傅里叶转换红外光谱仪(FT-IR)和核磁共振氢谱仪(~1 H-NMR)对共聚物的苯乙烯磺酸钠结构单元进行了表征,研究了反应条件对共聚物磺化度的影响;通过差示扫描量热仪(DSC)和热重分析仪(TG)研究了磺酸基团的引入对共聚物的玻璃化转变温度和起始分解温度的影响;通过旋转流变仪研究了磺化度对共聚物剪切黏度的影响;初步探讨了PP/P(St-co-NaSS)共混体系的染色性能。结果表明:当反应时间为2h,反应温度为70℃,引发剂质量分数为0.6%,苯乙烯磺酸钠的摩尔分数为0.01时,共聚物的磺化度f=6.68%(零切黏度η0=19 620Pa·s,属牛顿流体);在10~(-2)~10~(-1) s~(-1)的剪切速率范围内,P(St-co-NaSS)表现出假塑性流体的特征,具有较好的加工流动性。对于PP/P(St-co-NaSS)共混体系,使用阳离子染料染色时,染色深度(K/S值)为2.603 2,使用分散染料染色时,K/S值为10.168 8。P(St-co-NaSS)适合作为聚丙烯纤维的可染改性添加剂。     

Dehydration of glycerol with silica–phosphate-supported copper catalyst

Research on Chemical Intermediates - Silica–phosphate-supported copper catalyst was prepared by neutralization of sodium silicate with orthophosphoric acid followed by the addition of copper...     

Étude de la transition conformationnelle de l'acide polyacrylique syndiotactique en solution aqueuse par spectroscopie de vibration

The Raman and infrared spectra of syndiotactic polyacrylic acid have been investigated as a function of neutralization, in aqueous solution. The acid and its sodium salt have a planar zig-zag configuration. The progressive shift of the Raman line assigned to the vibration mode v(C-COOH) between 20 % and 50 % neutralization indicates a conformational transition from the degree of ionization α = 0.2. The absence of hydrogen bond of the unionized and partially ionized acid is corroborated.     

水性聚氨酯乳化过程中相转变的研究

本文合成了单官能团小分子物质封端的脂肪族水性聚氨酯预聚物 ,通过考察预聚物加水乳化过程中粘度及电导率的变化 ,研究了其相转变行为 .实验结果表明 ,随着软段分子量升高 ,体系的相转变点后延 ;聚酯体系的相转变比聚醚体系的相转变发生得早 ;[NCO]/ [OH]值越接近 1,体系的粘度就越高 ,相转变发生所需的水含量也越高 ;羧基含量及中和度也会对分散体系的相转变产生影响 .通过选择合适的条件 ,可以实现对乳化过程的优化     

The State of NaOH in NaOH/Poly(Sodium Acrylate) Composite

NaOH/poly(sodium acrylate) composites were prepared by in situ polymerization of acrylic acid with an overneutralization level by adding excess NaOH. The composites were studied by XRD, IR and ²³Na MAS NMR spectroscopy. The results showed that the high neutralization degree (>100%) may lead to a complete polymerization. Both XRD and ²³Na MAS NMR spectra did not show any peaks of phase-separated NaOH or Na₂CO₃ until the neutralization degree was up to 217.5%. It can be presumed that the aggregates of Na⁺ ions can contain approximately two Na⁺ units for every carboxyl group before the phase separation.     

ORGANOSILANE POLYMERS: SYNTHESIS AND CROSSLINKING OF FORMABLE POLYMERS CONTAINING PHENYLSILYLENE UNITS

Polysilane polymers which contain silicon hydride units in the chain were synthesized by sodium coupling of PhHSiCl_2 with R~1R~2SiCl_2 in toluene (R~1 and R~2 alkyl, aryl or aralkyl), followed by termination with a monochlorosilane and neutralization with sodium bicarbonate solution. These polymers are soluble in common solvents and can be formed into a variety of shapes by molding, casting, coating or potting. This class of polymers can be crosslinked by oxidation and irradiation, or by reaction with a multifunctional vinylsilane in th presence of platinum complexes.     

Synthesis,characterization and water absorbency properties of poly(acrylic acid)/sodium humate superabsorbent composite

A novel poly(acrylic acid)/sodium humate superabsorbent composite was synthesized by aqueous solution polymerization of acrylic acid using N, N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator in the presence of sodium humate. The effects on water absorbency such as initial monomer concentration, degree of neutralization of acrylic acid, amount of crosslinker, initiator and sodium humate, etc. were investigated. The water absorbency of the superabsorbent composite synthesized under optimal synthesis conditions with a sodium humate content of 20% exhibited an absorption of 1268 g H₂O/g sample and 93 g H₂O/g sample in distilled water and in 0.9 wt% NaCl solution, respectively. Swelling rate and water retention tests were also carried out. The results show that sodium humate, as a kind of functional filler, can enhance comprehensive properties of superabsorbent composite and reduce the product cost significantly. Copyright © 2005 John Wiley & Sons, Ltd.     

Emulsion polymerization of styrene using an alkali-soluble random copolymer as polymeric emulsifier

An alkali-soluble random copolymer (ASR), poly(styrene/α-methylstyrene/acrylic acid), was used as a polymeric emulsifier in the emulsion polymerization of styrene. The calorimetric technique was applied to study the kinetics of emulsion polymerization of styrene using ASR and a conventional ionic emulsifier, sodium dodecyl benzenesulfonate (SDBS). ASR could form aggregates like micelles, and the solubilization ability of the aggregates was dependent on the neutralization degree of ASR. The rate of polymerization in the ASR system was lower than that in the SDBS system. This result can be explained by the creation of a hairy ASR layer around the particle surface, which decreases the diffusion rate of free radicals through this region. Although a decrease in particle size was observed, the rate of polymerization decreased with increasing ASR concentration. The higher the concentration of ASR is, the thicker and denser ASR layer may be, and the more difficult it would therefore be for radicals to reach the particle through this layer of ASR. The rate of polymerization decreased with increasing the neutralization degree of ASR. The aggregates with high neutralization of ASR are less efficient in solubilizing the monomer and capturing initiator radicals than that of the lower neutralization degree, which leads to decrease in rate of polymerization. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2865–2872, 1998     

Thermogravimetry of deposited caustic soda used as a flame-retardant for cotton fabric

We have investigated the effect of caustic soda as a nondurable finish on the flammability of 100% cotton fabric (plain 180 g m^?2). On the contrary to the mercerization, during the impregnation process, no tension was applied. In order to attain the alkali cellulose onto the fabric, the subsequent neutralization was not followed. Each bunches of fabrics were dipped into individual aqueous solutions of sodium hydroxide, followed by means of squeeze rolls and drying at 110°C. After conditioning nightlong, by using our ‘vertical flame test’ the optimum add-on values to impart flame-retardancy into cotton fabric was determined as 1.3 g sodium hydroxide per 100 g fabric. Thermogravimetry and derivative thermogravimetry (TG/DTG) of pure cotton, treated cotton with sodium hydroxide at its optimum efficiency to impart flame-retardancy into the fabric was fulfilled and the obtained curves were compared and commented. The effectiveness of this hydroxide is attributed to the heat dissipation by the remaining material in the consumed ash. The results obtained are in favour of ‘dust or wall effect theory’ and also gas dilution theory.     

Diffusion of cyclodextrins in aqueous polymer solutions

Diffusion of α and β cyclodextrin (α-CD and β-CD, respectively) has been studied in aqueous solutions of poly(methacrylic acid), sodium poly(styrene sulfonate), having three different degrees of sulfonation (DS), and copoly(styrene-methacrylic acid) containing three different amounts of styrene. N-Acetylglucosamine and raffinose were included as reference diffusants. It was found that a decrease of the diffusion coefficients of the CD's in these polymer solutions is characteristically dependent on the polymer concentration, DS, Styrene content, and the degree of neutralization. The results were interpreted by assuming a 1:1 complex formation between CD and an appropriate residue in the polymer. The complex diffusion behavior of CD in the copolymer solutions suggested that the ability of the polymer residue to form complexes with the CD is lost when the polymer chain dimensions are reduced with decreasing neutralization.     

红外光谱鉴定聚丙烯中受阻胺光稳定剂

本文报道了用红外光谱方法鉴定的高分子和小分子受阻胺光稳定剂。此法包括溶解聚丙烯,接着用H_2SO_4沉淀并萃取,所得水溶液用NaOH中和并用二氯甲烷萃取,除去溶剂后残渣用IR鉴定。     

2-甲基-6-溴苯并碲唑及其衍生菁染料的合成

以对溴苯胺为原料,经汞化、酰化,再与四氯化碲发生亲电取代反应生成2-乙酰氨基-5-溴苯基三氯化碲(内盐);后者以硼氢化钠还原、浓盐酸关环,用碳酸氢钠中和后即得关键中间体2-甲基-6-溴苯并碲唑。苯并碲唑经碘甲烷或碘乙烷季铵化后,用原甲酸三乙酯缩合制得相应的对称染料2,2'-二甲基-5,5'-二溴碲碳菁碘盐和2,2'-二乙基-5,5'-二溴碲碳菁碘盐。测定了它们的可见吸收光谱。     

丙烯酸与海藻酸钠共聚制备耐盐性高吸水树脂

丙烯酸与海藻酸钠共聚制备耐盐性高吸水树脂     

反相悬浮聚合法合成超强吸水剂

探讨采用反相悬浮聚合法、合成聚丙烯酸盐超强吸水剂的工艺条件。结果表明：反应液中和废、单体浓度反应引发温度及交联剂种类及用量，对聚合反应的稳定进行有着很大的影响。采用本法制成的超强吸水剂，其吸去离子水能力达１２００－１４００ｇ／ｇ。制成的吸水剂凝胶粒子有一定的粒径分布。