Poly (ethylene terephthalate) thermo-mechanical and thermo-oxidative degradation mechanisms

¹H NMR and MALDI-TOF MS measurements were used to study the thermo-mechanical and thermo-oxidative degradation mechanisms of bottle-grade PET (btg-PET). In the thermo-oxidative degradation, the concentration of low molar mass compounds increased with time and the main products were cyclic and linear di-acid oligomers. In the thermo-mechanical degradation, the main-chain scission reactions affect the stability of the cyclic oligomers. One of the most important bottle-grade PET co-monomers is diethylene glycol (DEG), which is a “reactive site” in the thermal degradation of btg-PET. The DEG co-monomer was shown to be the precursor to colour changes in btg-PET, owing to the attack by molecular oxygen on the methylenic protons adjacent to the ether oxygen atoms of DEG. This behaviour was observed in the thermo-oxidative degradation process in which the degradation of DEG causes the release of hydroxyl radicals in the polymeric matrix, thereby producing mono- and di-hydroxyl substituted species. This was also observed in the thermo-mechanical degradation process.     

Colour formation in poly(ethylene terephthalate) during melt processing

The discolouration, that occurs in virgin poly(ethylene terephthalate) - PET during melt processing, was studied using various bulk and surface analytical techniques. Proton nuclear magnetic resonance (¹H NMR) was used to study the bulk chemical changes occurring in the polymer during thermo-oxidative degradation. Chemical derivatisation with trifluoroacetic anhydride (TFAA) was used to label the hydroxyl groups introduced on the polymer surface by thermal oxidation.From the surface analysis studies using photoacoustic Fourier transform infrared spectroscopy (PA/FT-IR), diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) and X-ray photoelectron spectroscopy (XPS) it was evident that colour formation starts initially with the hydroxylation of the terephthalic ring. Further, the formation of additional carbonyl functionalities and conjugated chromophoric systems complete the colour formation process.     

Synthesis and hydrolytic degradation of poly(ethylene succinate) and poly(ethylene terephthalate) copolymers

The conditions of synthesis of statistical poly(ethylene succinate-co-terephthalate) copolymers (2GTS) and high molecular weight poly(ethylene succinate) (PES) with good hydrolytic and optical parameters, designed for the production of biodegradable products and resins, are presented in this article. Copolymers were prepared by melt polycondensation of bis-(β-hydroxyethylene terephthalate) (BHET) and succinic acid (SA) with excess of ethylene glycol (2G) in the presence of a novel titanium/silicate catalyst (C-94) and catalytic grade of germanium dioxide (GeO₂) as cocatalyst. The chemical structure and physical properties of those materials were characterized by ¹H NMR, FT-IR, dynamical-mechanical thermal analyses (DMTA), differential scanning calorimetry (DSC), solution viscosity and spectroscopic methods. The hydrolytic degradation was performed in a water solution with variable pH, also in garden soil and in compost. The highest hydrolytic degradation rate was observed for pH 4 and for compost. Better hydrolytic degradation values in compost medium were observed for copolyester prepared in the presence of GeO₂ as polycondensation cocatalyst. The copolyester with 40 mol% of aliphatic units was chosen for industrial syntheses which were performed in ELANA and subsequently the processing parameters and compatibility with potato starch of this polyester were checked by BIOP Biopolymer Technologies AG.     

The Degradation of Poly(ethylene terephthalate)

The penetration of new markets by polyester fibers has emphasized the need for increased stability of the polyester toward a variety of degradative reactions. Extensive studies of the nature of the thermal, hydrolytic, oxidative, and radiation-induced degradation reactions have been reported. The interpretation of kinetic investigations and the identification of the reaction products have been facilitated by using suitable esters as model compounds in place of the polymeric species.     

Organocatalytic depolymerization of poly(ethylene terephthalate)

We describe the organocatalytic depolymerization of poly(ethylene terephthalate) (PET), using a commercially available guanidine catalyst, 1,5,7‐triazabicyclo[4.4.0]dec‐5‐ene (TBD). Postconsumer PET beverage bottles were used and processed with 1.0 mol % (0.7 wt %) of TBD and excess amount of ethylene glycol (EG) at 190 °C for 3.5 hours under atmospheric pressure to give bis(2‐hydroxyethyl) terephthalate (BHET) in 78% isolated yield. The catalyst efficiency was comparable to other metal acetate/alkoxide catalysts that are commonly used for depolymerization of PET. The BHET content in the glycolysis product was subject to the reagent loading. This catalyst influenced the rate of the depolymerization as well as the effective process temperature. We also demonstrated the recycling of the catalyst and the excess EG for more than 5 cycles. Computational and experimental studies showed that both TBD and EG activate PET through hydrogen bond formation/activation to facilitate this reaction. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Thermal degradation investigation of poly(ethylene terephthalate)/fibrous silicate nanocomposites

Based on the fibrous silicates (palygorskite, PT) organically modified by water-soluble polyvinylpyrrolidone (PVP), poly(ethylene terephthalate) (PET) nanocomposite with good dispersion of the PT nano-particles was prepared via in situ polycondensation. The thermal degradation behavior of PET and PET/PT nanocomposite was investigated by thermogravimetric analysis (TGA) under non-isothermal conditions at various heating rates in air and nitrogen, respectively. The apparent activation energies of the samples were evaluated by Kissinger and Flynn-Wall-Ozawa method. It is suggested that, during thermal decomposition in nitrogen, the clay as a mass-transport protective barrier can slow down degradation of polymer, but the catalytic effect of metal derivatives in clays may accelerate the decomposition behavior of PET. The combination of these two effects determines the final thermal stability of nanocomposite. However, in air atmosphere, the oxidative thermal stability of PET/PT nanocomposite was obviously superior to that of pure PET.     

Thermal degradation and isothermal crystalline behavior of poly（trimethylene terephthalate）

Poly(trimethylene terephthalate)(PTT) is an excellent fiber material.Its thermal degradation and isothermal crystalline behaviors were in this study investigated using thermogravimetric analysis(TGA),thermogravimetric analysis-Fourier transform infrared spectroscopy(TGA-FTIR) analysis,differential scanning calorimetry(DSC) and X-ray diffraction(XRD).The thermal degradation mechanism of PTT follows Mclafferty rearrangement principle.The PTTwithintrinsicviscosity(Ⅳ) of 0.74 dL/g has a maximum crystallinity...     

IR laser ablative degradation of poly(ethylene terephthalate): Formation of insoluble films with differently bonded CO groups

IR laser-induced degradation of poly(ethylene terephthalate) (PET) was studied under different irradiation conditions and the ablated volatile and solid products were characterized by mass and infrared spectroscopy, gel-permeation chromatography, thermogravimetry and electron microscopy. The observed volatile products (carbon oxides, H₂, C_1-2 hydrocarbons, acetaldehyde, benzene and toluene) and less-volatile aromatic compounds are typical products of thermal degradation of PET. The ablatively deposited solid materials are a blend of soluble, structurally similar oligomers and of an insoluble polymer containing carbonyl groups bonded in a -C(O)OH arrangement. Thermal degradation of these deposited solids is controlled by decomposition of sublimed fractions and is easier than that of PET.     

Thermal and thermo-oxidative degradation of poly(hydroxy ether of bisphenol-A) studied by TGA/FTIR and TGA/MS

The nature and the extent of degradation of poly(hydroxy ether of bisphenol-A) phenoxy resin were analysed by thermogravimetry (TGA/DTGA) under nitrogen and air atmosphere. Decomposition kinetics were elucidated according to Flynn-Wall-Ozawa, Friedman and Kissinger methods. The evolved gases during degradation were inspected by a thermogravimetry analyser coupled with Fourier Transform Infrared Spectrometer (TGA/FTIR) and also with a TGA coupled to a Mass Spectrometer (TGA/MS). Mass spectra showed that chemical species evolved in phenoxy decomposition in air were very similar to those assigned from degradation in nitrogen (water, methane, CO, CO₂, phenol, acetone, etc.). However, these species appear in different amount and at different temperatures in both atmospheres. FTIR analysis of the evolved products showed that water and methane were the beginning decomposition products, indicating that decomposition is initiated by dehydration and cleavage of C-CH₃ bond in the bisphenol-A unit of phenoxy resin. After this initial stage, random chain scission is the main degradation pathway. Nevertheless, in air atmosphere, previously the complete decomposition of the phenoxy obtaining fundamentally CO₂, and water, the formation of an insulated surface layer of crosslinked structures has been proposed.     

The influence of vacuum-ultraviolet radiation on poly(ethylene terephthalate)

Poly(ethylene terephthalate) was exposed to radiation from different kinds of low-pressure plasmas in an oxygen atmosphere. The lower wavelength limit of the spectrum investigated, λ = 112 nm, is the cut-off of magnesium fluoride used for separating the specimen chamber from the plasma light source. The total surface oxygen concentration, and the formation of hydroxyl, carbonyl, and carboxyl groups were evaluated from XPS measurements in combination with chemical derivatizations, and their dependences on the radiation spectrum and the oxygen pressure in the sample chamber have been investigated. © 1996 John Wiley & Sons, Inc.     

The effect of annealing on the subsequent cold crystallization of amorphous poly(ethylene terephthalate)

Amorphous poly(ethylene terephthalate) was annealed at temperatures around the glass transition temperature and then heated up in differential scanning calorimeter at 20 °C min⁻¹. It was found that the annealing favored the subsequent cold crystallization and this effect became stronger with increasing annealing temperature. The experimental results were explained by considering the structural change during the annealing.     

High‐pressure DTA of poly(butylene terephthalate), poly(hexamethylene terephthalate), and poly(ethylene terephthalate)

Pressure effect on the melting behavior of poly(butylene terephthalate) (PBT) and poly(hexamethylene terephthalate) (PHT) was studied by high‐pressure DTA (HP‐DTA) up to 320 and 530 MPa, respectively. Cooling rate dependence on the DSC melting curves of the samples cooled from the melt was shown at atmospheric pressure. Stable and metastable samples were prepared by cooling from the melt at low and normal cooling rates, respectively. DTA melting curves for the stable samples showed a single peak, and the peak profile did not change up to high pressure. Phase diagrams for PBT and PHT were newly determined. Fitting curves of melting temperature (T_m) versus pressure expressed by quadratic equation were obtained. Pressure coefficients of T_m at atmospheric pressure, dT_m/dp, of PBT and PHT were 37 and 33 K/100 MPa, respectively. HP‐DTA curves of the metastable PBT showed double melting peaks up to about 70 MPa. In contrast, PHT showed them over the whole pressure region. HP‐DTA of stable poly(ethylene terephthalate) (PET) was also carried out up to 200 MPa, and the phase diagram for PET was determined. dT_m/dp for PET was 49 K/100 MPa. dT_m/dp increased linearly with reciprocal number of ethylene unit. The decrease of dT_m/dp for poly(alkylene terephthalate) with increasing a segmental fraction of an alkyl group in a whole molecule is explained by the increase of entropy of fusion. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 262–272, 2000     

The effect of annealing on the crystallization of poly(ethylene terephthalate)/polycarbonate blends

The effect of annealing on the morphology and subsequent crystallization kinetics of poly (ethylene terephthalate)/polycarbonate blends have been investigated using differential scanning calorimetry (DSC), polarized light microscopy, and scanning electron microscopy (SEM). During annealing transesterification and phase coarsening occurred, and the final properties were compromizes between these two competing effects. Initially, the effect of phase separation dominated and the rate of cold crystallization of PET increased. Transesterification, however, became increasingly important and the rate of crystallization decreased progressively until finally the blend completely lost the ability to crystallize. At this stage in the reaction a single glass transition was observed and uniform glassy material observed in the SEM. The maximum crystallinity of the blend achieved on heating showed the same trend in first increasing and then decreasing with annealing time. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2129–2136, 2004     

A novel method for preparing poly(ethylene terephthalate)/BaSO4 nanocomposites

We developed a novel method for preparing poly(ethylene terephthalate)/BaSO₄ nanocomposites, which were synthesized by in situ polymerization of terephthalic acid (TPA), ethylene glycol (EG) and BaSO₄ nanoparticles prepared by reacting H₂SO₄ with Ba(OH)₂ in ethylene glycol (EG). It was shown that the addition of BaSO₄ would not influence the synthesis of PET. The structure of the nanocomposites was characterized by transmission electron microscopy (TEM), and the nanoscale dispersion of BaSO₄ particles in the PET matrix was observed when the BaSO₄ content is below 4 wt%. Moreover, the thermal properties of the nanocomposites were investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The results suggest that the degree of dispersion of BaSO₄ particles in the PET matrix has important effect on the thermal properties of the nanocomposites. The existence of BaSO₄ nanoparticles enhances the crystallization rate of PET. Besides, it was found that the thermal stability of PET was improved by the addition of the BaSO₄ nanoparticles.     

Fast crystallization of poly(ethylene terephthalate)

The crystallization of poly(ethylene terephthalate) (PET) was studied in the presence of nucleating agents and promoters. The effect of both by themselves and in concert was investigated using differential scanning calorimetry. The aim of this work is to find conditions of fast crystallization of PET. Sodium benzoate(SB) and Surlyn® (S) substantially increase the crystallization rate of PET at higher temperature owing to a reduction in the energy barrier towards primary nucleation, but they accelerate crystallization even more at lower temperature with an additional improvement of the molecular mobility of PET chains. Chain scission of PET caused by the reaction with the nucleating agents was proven by determination of molecular weight. The addition of S alone led to a lower reduction in molecular weight. A series of N-alkyl-p-toluenesulfonamides (ATSAs) were shown to effectively promote molecular motion of the PET chains, leading to an increase in crsytallization rate at lower temperature. A remarkable acceleration of crystallization of PET was attained at lower temperature when S and ATSA were added together. When the content of ATSA is low, S has the dominant influence due to its dual effect of decreasing energy barrier towards nucleation and promoting molecular motion of PET chains. A further increase of crystallization rate of PET was found only after an addition of ATSA of above 5 wt.%.Dedicated to Professor Bernhard Wunderlich on the occasion of his 65th birthdayThis work was supported by State Science and Technology Commission, and partially by National Science Foundation.     

The dispersion of pigment slurries via incorporation with water-soluble sulfonate poly(ethylene terephthalate)

A water-soluble sulfonate poly(ethylene terephthalate) copolymer has been synthesized and identified as a high-temperature endurable surfactant. The glass-transition temperature and the storage modulus increase in correlation to the increase in sulfonate content. Various characterization studies were performed, including light scattering, zeta-potential measurement and a sedimentation test. The results suggest that at equal numbers of sulfonate units in a solution, a low concentration of a dispersant of high sulfonate content is more effective than a high concentration of a dispersant of low sulfonate content. Received: 6 April 2000 Accepted: 23 September 2000     

Conformation of the ground-state dimer in poly(ethylene terephthalate)

Absorbance, excitation, and emission measurements have been performed with methyl benzoate and five model compounds, C₆H₅COO (CH₂)_xOOCC₆H₅, x = 2–6. Under appropriate conditions, three of the model compounds (those with x = 3, 4, 5) show evidence for the formation of intramolecular ground-state dimers. The model compound with x = 5 can form two types of dimers which emit with different energies. The model compound with x = 3 forms one of these dimers, and the model compound with x = 4 prefers the other ground-state dimer. Molecular modeling of the dimers suggests that the two conformations of the ground-state dimers differ in the orientation of the two C?O bonds. In the one dimer these two bonds are nearly parallel, but in the other they make an angle of about 120°. © 1993 John Wiley & Sons, Inc.     

Heterogeneous nucleation on the crystallization poly(ethylene terephthalate)

The crystallization behavior of poly(ethylene terephthalate) (PET) with disodium terephthalate (DST) as nucleating agent was investigated. A detailed analysis of the crystallization course from the melt was made with the Avrami expression. The results demonstrated that DST additive can promote the PET crystallization rate in its entire crystallizable temperature range, and the acceleration degree of DST decreases with increasing temperature after a temperature higher than 180 °C. The values of the Avrami exponent indicated that the crystallization mode in Avrami theory is not suitable for the crystallization of these polymers, and the mechanism of the heterogeneous nucleation on PET crystallization is discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2135–2144, 2003     

Electron beam irradiation effects on poly(ethylene terephthalate)

Changes in poly(ethylene terephthalate) subjected to electron beam irradiation at doses up to 15 MGy and dose rate of 1.65 MGy/h, were investigated by differential scanning calorimetry, molecular weight measurement, X-ray photoelectron spectroscopy, and scanning electron microscopy. Irradiated samples showed a decrease of molecular weight with a minimum at 5 MGy, which is attributed to chain scission of the macromolecules and then an increase at further doses due to branching and some degradation effect. Irradiation in air is not an important factor because the high dose rate of irradiation inhibits oxygen diffusion in the samples.     

Elastic behavior of poly(ethylene terephthalate) chains

The Monte Carlo (MC) method based on the rotational-isomeric-state (RIS) model is adopted in studying the elastic behavior of poly(ethylene terephthalate) (PET) chains in this paper. The mean-square end-to-end distance 〈R²〉, the mean-square radius of gyration 〈S²〉, and the ratio of 〈R²〉/〈S²〉 all increase with elongation ratio λ. The interior conformations are also investigated through calculating the a priori probability of rotational state in the process of tensile elongation. The radius of gyration tensor S is introduced here in order to measure the shape of PET chains, and increases with elongation ratio λ, however, some different behaviors are obtained for . Here , and are the eigenvalues of the radius of gyration tensor . The average energy per repeat unit 〈U〉 and the average free energy per repeat unit 〈A〉 are also calculated, and we find that the average energy decreases with elongation ratio λ, however, the average free energy per repeat unit increases with elongation ratio λ. Elastic force f, energy contribution to force f_U, and entropy contribution to force f_S are also investigated. Both elastic force f and entropy contribution to force f_S increases with λ, however, energy contribution to force f_U and the ratio f_U/f decreases with λ. The ratio of f_U/f is less than zero and almost independent of chain length. The results of these microscopic calculations may explain some macroscopic phenomena of rubber elasticity.