The effect of post-consumer PET particles on the performance of flexible polyurethane foams

In this work, the use of post-consumer PET (polyethylene terephthalate), PET_pc, as reinforcement filler in flexible polyurethane foams was studied, with the aim of finding alternatives for the recycling of polymer packaging. Density, number of cells per linear centimeter, tensile resistance, strain at break and tear resistance of standard foams were compared to those of foams with PET_pc in the formulation, using 1.5 parts per hundred of polyol of PET_pc (granulometric range 0–297 μm). The produced foams were sectioned into top, mid-top, mid-bottom and bottom layers. Tensile resistance, strain at break and tear resistance of the reinforced foam surpassed those of the standard foam for all layers. The number of cells was constant but density increased towards the base of the block. In addition, the filled foams yielded better wear, compression set and compression resistance than the standard foam, whereas no significant variation in morphology (cell shape) was found.     

Electrospun recycled PET-based mats: Tuning the properties by addition of cellulose and/or lignin

The aim of this study was to evaluate the influence of cellulose and/or lignin on the properties of mats prepared from dissolution (for 48 h or 72 h, solvent: trifluoroacetic acid) of recycled poly (ethylene terephthalate) (PET). Briefly, the presence of cellulose led to a tendency of higher average fiber diameter and average pore area as well as lower average porosity compared to the neat mat (PET_ref, 242 ± 59 nm, 9.6 ± 1.1 10⁴ nm² and 19.0 ± 1.1%, respectively). The T_g values for electrospun PET combined with cellulose and/or lignin were higher than that of PET_ref (92.5 ± 0.1 °C), and the tensile strength increased with the cellulose and/or lignin loading. In addition, the presence of lignin (72 h of dissolution) led to a mat with an elongation at break of 149 ± 9% compared to 14 ± 2% for PET_ref. The results indicated that the properties of mats based on PET can be tuned by adding cellulose and/or lignin to solutions posteriorly electrospun as well as by varying the dissolution time.     

Poly (ethylene terephthalate) thermo-mechanical and thermo-oxidative degradation mechanisms

¹H NMR and MALDI-TOF MS measurements were used to study the thermo-mechanical and thermo-oxidative degradation mechanisms of bottle-grade PET (btg-PET). In the thermo-oxidative degradation, the concentration of low molar mass compounds increased with time and the main products were cyclic and linear di-acid oligomers. In the thermo-mechanical degradation, the main-chain scission reactions affect the stability of the cyclic oligomers. One of the most important bottle-grade PET co-monomers is diethylene glycol (DEG), which is a “reactive site” in the thermal degradation of btg-PET. The DEG co-monomer was shown to be the precursor to colour changes in btg-PET, owing to the attack by molecular oxygen on the methylenic protons adjacent to the ether oxygen atoms of DEG. This behaviour was observed in the thermo-oxidative degradation process in which the degradation of DEG causes the release of hydroxyl radicals in the polymeric matrix, thereby producing mono- and di-hydroxyl substituted species. This was also observed in the thermo-mechanical degradation process.     

Enzymatic and microbial biodegradability of poly(ethylene terephthalate) copolymers containing nitrated units

Enzymatic and microbial degradability of poly(ethylene terephthalate) (PET) and PET copolyesters containing 30 mol% of either 5-nitroisophthalic units (PET₇₀NI₃₀) or nitroterephthalic units (PET₇₀NT₃₀) was investigated in laboratory cultures. Two commercial fungal lipases, two bacteria from environmental isolates, and two collection filamentous fungi were tested. The topography of the polymer surface exposed to degradation was characterized by interferometry-confocal microscopy techniques. Biodegradation was estimated by optical and electron microscopy observation, and gel permeation chromatography. Evidence of biodegradation including roughness enhancement, swelling and decrease of the weight-average molecular weight, was only obtained for the case of PET₇₀NT₃₀ cultured with Aspergillus niger. Differences in surface textures were found to be crucial to determine the positive response of this copolyester to biodegradation.     

Poly(ethylene terephthalate) copolymers containing 5‐tert‐butyl isophthalic units

Poly(ethylene terephthalate‐co‐5‐tert‐butyl isophthalate) copolymers, abbreviated as PET^tBI, with compositions ranging between 95/5 and 25/75, as well as the two parent homopolymers, PET and PE^tBI, were prepared from comonomer mixtures by a two‐step melt‐polycondensation. Polymer intrinsic viscosities varied from 0.4 to 0.7 dL g^?1 with weight‐average molecular weights ranging between 31,000 and 80,000. The copolymers were found to have a random microstructure with a composition according to that used in the corresponding feed. The melting temperature and crystallinity of PET^tBI decreased with the content in 5‐tert‐butyl isophthalic units, whereas the glass‐transition temperature increased from 82 °C for PET up to 99 °C for PE^tBI. Copolymerization slightly improved the thermal stability of PET. Preliminary X‐ray diffraction studies revealed that PET^tBI adopt the same crystal structure as PET with the alkylated isophthalic units probably excluded from the crystal lattice. The homopolymer PE^tBI appeared to be a highly crystalline polymer taking up a crystal structure clearly different from that of PET and PET^tBI copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 1994–2004, 2001     

N-functionalized cyclam based trinuclear copper(II) complexes: electrochemical,magnetic, catalytic and antimicrobial studies

A series of trinuclear Cu(II) complexes have been prepared by Schiff base condensation of 1,8-[bis(3-formyl-2-hydroxy-5-methyl)benzyl]-l,4,8,11-tetraazacyclotetradecane and 1,8-[bis(3-formyl-2-hydroxy-5-bromo)benzyl]-l,4,8,11-tetraazacyclotetradecane with aromatic and aliphatic diamines, Cu(II) perchlorate and triethylamine. The complexes were characterized by elemental and spectroscopic analysis. Electrochemical studies of the complexes in DMF solution show three irreversible one-electron reduction processes around E_pc ¹ = −0.73 to −0.98 V, E_pc ² = −0.91 to −1.20 V and E_pc ³ = −1.21 to −1.33 V. ESR spectra and magnetic moments of the trinuclear Cu(II) complexes show the presence of antiferromagnetic coupling. The rate constants for hydrolysis of 4-nitrophenylphosphate by the Cu(II) complexes are in the range of 3.33 × 10⁻² to 7.58 × 10⁻² min⁻¹. The rate constants for the catecholase activity of the complexes fall in the range of 2.67 × 10⁻² to 7.56 × 10⁻² min⁻¹. All the complexes were screened for antifungal and antibacterial activity.     

A new approach of characterizing the hydrolytic degradation of poly(ethylene terephthalate) by MALDI-MS

The hydrolytic degradation of technical poly(ethylene terephthalate) (PET) was investigated by means of different methods such as size-exclusion chromatography (SEC), viscometry, light-scattering, thin-layer chromatography, end-group titration, and matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS). The long-term degradation was simulated by exposing PET filament yarns to aqueous neutral conditions at 90°C for up to 18 weeks. By means of MALDI-MS and thin-layer chromatography, the formation of different oligomers was obtained during polymer degradation. As expected, an ester scission process was found generating acid terminated oligomers (H-[GT]_m-OH) and T-[GT]_m-OH and ethylene glycol terminated oligomers (H-[GT]_m-G), where G is an ethylene glycol unit and T is a terephthalic acid unit. Additionally, the scission of the ester bonds during the chemical treatment led to a strong decrease in the number of cyclic oligomers ([GT]_m). The occurrence of di-acid terminated species demonstrated a high degree of degradation. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2183–2192, 1997     

Validation of a fast screening method for the detection of cocaine in hair by MALDI-MS

The sensitivity and specificity of a novel method of screening for cocaine in hair, based on matrix-assisted laser desorption/ionisation (MALDI) mass spectrometry (MS), have been evaluated. The method entails a rapid extraction procedure consisting of shaking 2.5 mg pulverised hair at high frequency in the presence of an acidic solution (160 μL of water, 20 μL of acetonitrile and 20 μL of 1 M trifluoroacetic acid) and a stainless-steel bullet. Following centrifugation, the supernatant is dried under a nitrogen stream, and the residue is reconstituted in 10 μL of methanol/trifluoroacetic acid (7:3; v/v). One microlitre of the extract is deposed on a MALDI sample holder previously scrubbed with graphite; an α-cyano-4-hydroxycinnamic acid (matrix) solution is electrosprayed over the dried sample surface to achieve a uniform distribution of matrix crystals. The identification of cocaine is obtained by post-source decay experiments performed on its MH⁺ ion (m/z 304), with a limit of detection of 0.1 ng/mg of cocaine. A total of 304 hair samples were analysed in parallel by MALDI-MS and a reference gas chromatography-MS method. The obtained results demonstrate specificity and sensitivity of 100% for MALDI-MS. Evidence of cocaine presence was easily obtained even when hair samples exhibiting particularly low cocaine levels (<0.5 ng/mg) were analysed.     

Coordination complexes of rare earth metals with hydrazine and isomeric acetamidobenzoates as ligands– spectral,thermal and kinetic studies

The isomeric acetamido benzoic acids (abbreviated as acambH) on reaction with hydrazine hydrate and lanthanides, La³⁺, Ce³⁺, Pr³⁺, Nd³⁺, Sm³⁺ and Gd³⁺ form complexes of formulae, [Ln{x-C₆H₄(CH₃CONH)}₃(N₂H₄)] where x = 2 (or) 3 (or) 4, at pH 3–4.5 in (1:1) aqueous ethanolic medium, which are insoluble in water and organic solvents. They are characterized by using elemental analysis, IR, UV, ¹³C, ¹H NMR and mass spectroscopic, XRD, SEM-EDAX, thermal and conductance studies. The difference between IR bands of v_{C=O asym} (acid) and v_{C=O sym}(acid) range, 122–166 cm^?1 supports the bidental coordination of carboxylate ions to metal. v_N-N values of 955 to 980 cm^?1, substantiate bridging bidentate coordination of hydrazine to metal. v_C=O of amide group 1632 to1709 cm^?1 indicates its non-coordination with metal. The thermal studies reveal that complexes undergo dehydrazination between 52 and 180 °C and exothermic degradation into phthalate intermediate between 172 and 496 °C and further degradation to form microsized metal oxide around 600 °C. The magnetic susceptibility measurements indicated that the presence of metals in the same electronic state and electronic spectral assignments suggested that the coordination number is eight for the complexes. The conductance measurement results in DMSO medium indicated that the complexes are neutral. The ¹³C – NMR, ¹H- NMR and the LC-Mass techniques substantiated the composition of the complexes.     

PET Diagnostic Molecules Utilizing Multimeric Cyclic RGD Peptide Analogs for Imaging Integrin αvβ3 Receptors

Multimeric ligands consisting of multiple pharmacophores connected to a single backbone have been widely investigated for diagnostic and therapeutic applications. In this review, we summarize recent developments regarding multimeric radioligands targeting integrin α_vβ₃ receptors on cancer cells for molecular imaging and diagnostic applications using positron emission tomography (PET). Integrin α_vβ₃ receptors are glycoproteins expressed on the cell surface, which have a significant role in tumor angiogenesis. They act as receptors for several extracellular matrix proteins exposing the tripeptide sequence arginine-glycine-aspartic (RGD). Cyclic RDG peptidic ligands c(RGD) have been developed for integrin α_vβ₃ tumor-targeting positron emission tomography (PET) diagnosis. Several c(RGD) pharmacophores, connected with the linker and conjugated to a chelator or precursor for radiolabeling with different PET radionuclides (¹⁸F, ⁶⁴Cu, and ⁶⁸Ga), have resulted in multimeric ligands superior to c(RGD) monomers. The binding avidity, pharmacodynamic, and PET imaging properties of these multimeric c(RGD) radioligands, in relation to their structural characteristics are analyzed and discussed. Furthermore, specific examples from preclinical studies and clinical investigations are included.     

LC Method for Studies on the Stability of Sibutramine in Soft Gelatin Capsules

A sensitive and rapid liquid chromatographic method was successfully developed and validated for the determination of sibutramine hydrochloride in bulk and capsules. Sibutramine in the presence of its degradation products was analyzed using UV detection at 225 nm. Chromatography was performed on a reversed-phase C₈ (150 × 4.0 mm I.D., 5 μm) analytical column under isocratic conditions. The mobile phase was composed of acetonitrile:water (aqueous phase containing 0.3% triethylamine and pH adjusted to 7.0) (75:25, v/v) at a flow-rate of 1.1 mL min⁻¹. No chromatographic interference was found during the analysis. Light was the stress condition which most contributed to sibutramine degradation. The method showed a linear response (r > 0.999) from 30 to 90 μg mL⁻¹. The mean recovery for capsules was 101.2%. Inter-day assays showed relative standard deviations of 0.42 and 1.62% for bulk and capsules, respectively. The developed method is able to separate sibutramine from its major degradation products and it may be used in the quality control of this active pharmaceutical ingredient in both bulk and capsules.     

A new composite electrode of Ni-Ferrite/TiOx/Si(111): Preparations and photoelectrochemical studies

A composite electrode of Ni-ferrite/TiO_x/Si(111) was synthesized by grafting Ni²⁺Fe²⁺Fe³⁺–LDH–TiCl₃ (LDH: Layered Double Hydroxides) on n-Si(111) surface and calcined under 1100 °C. Photoelectric research results indicated that the electrode had good photovoltaic effects in an electrolyte solution containing 7.6 M HI and 0.05 M I₂, while platinum plate was used as counter-electrode. The observed photo-voltages (U_pv) and photocurrent densities (j_pc) of the electrode were at ?0.75 V and 5.35 mA/cm², respectively. Compared with electrodes of oxidized n-Si(111) crystal and n-Si(111) wafer covered by Ni-ferrites, j_pc of the electrode Ni-ferrite/TiO_x/Si(111) was increased greatly.     

Effect of selected residual Ziegler-Natta and metallocene catalysts on the UV-induced degradation of unstabilized ethylene homopolymer films

Catalyst creates new grades of polyethylenes while their degradation phenomena determine the resulting application profiles. The resins and the end-products eventually contain residual catalysts. Therefore, the effects of the following two residual catalysts—one Ziegler-Natta [PQ Silica/Bu₂Mg/^tBuCl/TiCl₄], and the other metallocene [PQ Silica/MAO/(ⁿBuCp)₂ZrCl₂]—on the UV-induced degradation of the resulting unstabilized ethylene homopolymer films were studied. The MetCat HomoPE film was found to be more susceptible to UV-induced degradation degradation than the Z-N HomoPE one despite the residual Zr level was 1/15th of the Ti content. Therefore, the zirconocene residual catalyst better (i) facilitated the UV-initiated reaction, and (ii) decreased the activation energy required for the decomposition of the resulting hydroperoxide. These findings were explained from the differences in (i) electronic configuration and atomic radius, and (ii) surface chemistry and solid-state electronic environment of these catalyst systems. In both films, T_pm and T_pc did not significantly vary with the exposure time. The change of % crystallinity showed to be irregular and disturbed. As a function of carbonyl index, T_pm and T_pc,varied in a similar fashion in the MetCat HomoPE film. However, they significantly differed for the Z-N HomoPE film. Here, T_pm did not appreciably change whereas T_pc initially increased very mildly; then it did not essentially differ.     

Chain structure and thermal behavior of reactive blends of PET/LCP with bis(2-oxazoline)

The sequence structure and thermal behavior of reactive blends of poly(ethylene terephthalate) (PET) with the liquid crystalline copolyester 60 PHB/PET containing 60 mol % of p-hydroxybenzoic acid (PHB) with addition of bis(2-oxazoline) (BOZ) were studied in detail. ¹H NMR results indicate that both the number average sequence length of PET and PHB segments (L _PET and L _PHB) decrease with increasing mixing time and temperature via transesterification between PET and LCP. The transesterification is promoted in the presence of BOZ. As a consequence, the sequence structure and in turn the crystallization both from the glassy and the melt state and the melting behavior are markedly affected.     

Evaluation of single-point equations to determine intrinsic viscosity of sodium alginate and chitosan with high deacetylation degree

A viscometric study of two polyelectrolytes, chitosan (CH, with 94% deacetylation degree, in a solute-mixture of acetic acid (0.1 mol L⁻¹) and sodium chloride (0.2 mol L⁻¹) and sodium alginate (SA, with 62% M-units, in sodium chloride (0.1 mol L⁻¹), was performed at 25 °C. Five different equations were applied to calculate intrinsic viscosity [η]: Huggins, Kraemer and Schulz-Blaschke (SB) by graphical extrapolation; Solomon-Ciuta, Deb-Chanterjee and again SB, by faster single-point determination. Viscometric constants were calculated employing graphical extrapolation equations. Average molar mass (‾M_v) values were determined by applying the Mark-Houwink-Sakurada equation. For the samples analyzed, Huggins equation was the most suitable to calculate [η] and‾M_v by graphical extrapolation for chitosan, while Schulz-Blaschke and Solomon-Ciuta were adequate for single-point determinations of sodium alginate. Viscometric constants indicated that the aqueous mixture of acetic acid and sodium chloride is a poor solvent for chitosan, while sodium alginate is well solvated by aqueous sodium chloride.     

Spatial and Temporal Bioactive Compound Contents and Chlorophyll Fluorescence of Kale (Brassica oleracea L.) Under UV-B Exposure Near Harvest Time in Controlled Environments

UV-B irradiation has been used to enhance the secondary metabolite content in plants, but its spatial effect on plants has not been considered. The objective of this study was to compare spatial photosynthetic traits and bioactive compound accumulation in kale (Brassica oleracea L. var Acephala) according to the distribution and length of UV-B exposure near harvest. Plants were exposed to UV-B of 0–3, 3–6 and 6–9 W m⁻² for 4 h per day at 5 days (Exp. 1) and 4.2 W m⁻² at 5, 4, 3, 2 or 1 days (Exp. 2) before harvest. In spatial distribution, the higher the UV-B intensity, the lower the mean F_v/F_m (maximal photochemical efficiency of PSII) and the higher the concentration of total flavonoid compound (TFC). With UV-B stress, F_v/F_m and fluorescence transient parameters decreased except for DI₀/CS (dissipated energy flux per cross section) and PI_abs (performance index of PSII). When exposed to UV-B radiation for 2 days before harvest, the total phenolic compounds and TFC per plant were highest, not always proportional to the local F_v/F_m but affected by dry weight. Short-term UV-B stress near harvest would be more efficient for the accumulation of bioactive compounds by minimizing the loss of plant weight.     

Solubilization of caffeic acid into the cationic micelles and biogenic synthesis of silver nanoparticles for the degradation of dye

Solubilization of caffeic acid into the aqueous solution of cationic cetyltrimethlyammonium bromide (CTAB) has been studied by using differential spectroscopic and conductivity methods. The solubility of caffeic acid increases with increasing the CTAB concentrations. The solubilization constant of caffeic acid into CTAB (K_X = 1.8 × 10⁵), standard free energy (ΔG⁰_P = ?30.0 kJ/mol), and relative solubility (S_t/S₀ = 53.5) were estimated at room temperature from UV–visible data. The critical micellar concentration (CMC) of CTAB decreases linearly with caffeic acid concentration due to the presence of hydrophobic benzene moiety. The interaction of caffeic acid with CTAB has also been discussed. The solubilized caffeic acid was used as a reducing agent for the preparation of silver nanoparticles (AgNPs). The as-prepared AgNPs were used as an activator of persulphate. The generated reactive oxygen species (OH^?) and reactive sulphur species SO₄^-?) were responsible for the degradation of xylenol orange dye in water.     

The pressure effect study on the burning rate of ammonium nitrate-HTPB-based propellant with the influence catalysts

The burning rate of AN–HTPB-based propellant catalysed with chromium salt has been studied using conventional strand burner under the various pressure range, i.e. from atmospheric pressure to 6.897 MPa and verified with Piobert law, i.e. r = aP ⁿ . At atmospheric pressure, the burning rate AN–HTPB propellant was being accelerated with the chromium-based catalysts used. In case of lead chromate-catalysed system, burning rate was observed 2.655 times higher than burning rate (r = 0.200 mm s⁻¹) of virgin AN–HTPB propellant sample. However, the Copper chromate-catalysed propellant burned with slower rate (r = 0.160 mm s⁻¹) than the virgin AN–HTPB propellant sample. The burning rate of all catalysed propellant samples are found to be the pressure sensitive and accelerated higher with rise of pressure. The highest burning rate (r = 2.422 mm s⁻¹) was recorded with ammonium dichromate and lowest (r = 1.40 mm s⁻¹) with lead chromate-catalysed propellant sample with the rise of pressure up to 6.897 MPa at different pressures. A linear relationship was observed between the burning rate and pressure rise which followed the Piobert law, i.e. r = aP ⁿ . The pressure index (n) values of AN–HTPB-based samples were calculated higher when catalysed with ammonium dichromate, Copper Chromate, Cr₂O₃, Potassium dichromate (n = 0.525, 0.555, 0.429, and 0.408 respectively) and lower (n = 0.226) with lead chromate compared to virgin sample (n = 0.405). Higher value indicates the positive effect on accelerating the burning rate with catalyst at higher pressure ranges.     

Complete Depolymerization of PET Wastes by an Evolved PET Hydrolase from Directed Evolution

PETase displays great potential in PET depolymerization. Directed evolution has been limited to engineer PETase due to the lack of high-throughput screening assay. In this study, a novel fluorescence-based high-throughput screening assay employing a newly designed substrate, bis (2-hydroxyethyl) 2-hydroxyterephthalate (termed BHET-OH), was developed for PET hydrolases. The best variant DepoPETase produced 1407-fold more products towards amorphous PET film at 50 °C and showed a 23.3 °C higher T_m value than the PETase WT. DepoPETase enabled complete depolymerization of seven untreated PET wastes and 19.1 g PET waste (0.4 % W_enzyme/W_PET) in liter-scale reactor, suggesting that it is a potential candidate for industrial PET depolymerization processes. The molecular dynamic simulations revealed that the distal substitutions stabilized the loops around the active sites and transmitted the stabilization effect to the active sites through enhancing inter-loop interactions network.