Anaerobic biodegradation tests of poly(lactic acid) and polycaprolactone using new evaluation system for methane fermentation in anaerobic sludge

The anaerobic biodegradation tests of polycaprolactone (PCL) and poly(lactic acid) (PLA) powders were done at thermophilic temperature (55 °C) under aquatic conditions (total solid concentrations of the used sludge were 1.73% (undiluted sludge) and 0.86% (diluted sludge)) using a newly developed evaluation system. With this system, the evolved biogas is collected in a gas sampling bag at atmospheric pressure. This method is more convenient than using a pressure transducer or inverted graduated cylinder submerged in water. The biodegradation of PCL powder (10 g, 125–250 μm) in the diluted sludge stopped in about 47 days when the biodegradability reached 92%. The biodegradability of PLA powder (10 g, 125–250 μm) in undiluted sludge was 91% at about 75 days. The biodegradability of PLA powder (10 g, 125–250 μm) in diluted sludge was 79% at about 100 days. The biodegradability of PLA powder (5 g, 125–250 μm) in diluted sludge was 80% at about 85 days. It was found that the PCL and PLA powders were quite degraded using the new evaluation method. In addition, the smaller particle size PCL powder was biodegraded faster.     

Biodegradation of poly(lactic acid) powders proposed as the reference test materials for the international standard of biodegradation evaluation methods

The methods for producing reference test materials for biodegradation evaluation tests have been studied. Mechanical crushing at low temperature of polymer pellets using dry ice was selected for the method of producing polymer powder of poly(lactic acid) (PLA). The powders were fractionated using 60 mesh (250 μm) and 120 mesh (125 μm) sieves. The size distributions were then measured. The average diameter of the PLA particles obtained by this method was 214.2 μm. The biodegradation speeds of these PLA polymer powders were evaluated by two methods based on the international standard and one in vitro method based on the enzymatic degradation. First, the degree of biodegradation for this PLA powder was 91% for 35 days in a controlled compost determined by a method based on ISO 14855-1 (JIS K6953) at 58 °C managed by the Mitsui Chemical Analysis and Consulting Service, Inc. (Japan). Second, these polymer powders were measured for biodegradation by the Microbial Oxidative Degradation Analyzer (MODA) in a controlled compost at 58 °C and 70 °C based on ISO/DIS 14855-2 under many conditions. The degree of biodegradation for this PLA powder was approximately 80% for 50 days. In addition, the polymer powders were biodegraded by Proteinase K which is a PLA degradation enzyme. This polymer powder was suitable as a reference material for the evaluation methods of biodegradation.     

Influence of biodegradation on crystallization of poly (butylene adipate‐co‐terephthalate)

The biodegradation of aromatic‐aliphatic biodegradable polyester poly (butylene adipate‐co‐terephthalate) (PBAT) was studied under mesophilic (37°C) and thermophilic (55°C) anaerobic conditions. Anaerobic sludge from municipal wastewater treatment plant was utilized as an inoculum. Non‐isothermal crystallization kinetics of PBAT before and after biodegradation was explored by differential scanning calorimetry. Under mesophilic anaerobic conditions (37°C), the biodegradation after 126 days was only 2.2%, molecular weight changed from 93 000 to 25 500 g/mol, and the crystallization behavior was changed only slightly. However, biodegradation under thermophilic anaerobic conditions (55°C) caused much bigger changes: biodegradation according to biogas production reached after 126 days 8.3%, molecular weight changed from 93 000 to 9430 g/mol, and the crystallization behavior was changed significantly. While T_m increased only slightly, T_c on the other hand increased significantly for the sample after biodegradation at 55°C. Also, the crystallization rate was slower (particularly at lower cooling rates), but crystallinity was slightly higher. The diffraction pattern was observed by X‐ray diffraction.     

Self-accelerated biodegradation of electrospun poly(ethylene glycol)-poly(l-lactide) membranes by loading proteinase K

Proteinase K was successfully loaded inside ultrafine fibers of poly(ethylene glycol)-poly(l-lactide) (PELA) by emulsion electrospinning. A core/shell fiber structure was formed and verified by a transmission electron microscope. In vitro biodegradation of electrospun PELA membranes containing proteinase K (PELA-P) was examined in Tris-HCl buffer solution at pH 8.6 and 37 °C in comparison with electrospun PELA membranes without proteinase K. During biodegradation, mass loss, water absorption, pH value of the incubated buffer, fibrous morphology and thermal properties were monitored. Results suggested that PELA-P membranes degraded significantly faster than PELA membranes. A significant drop in pH value of the buffer after incubation of PELA-P membranes for 1 d was observed, and after 7 d, PELA-P membranes lost their fibrous appearance and masses almost completely. In contrast, electrospun PELA membranes did not show any obvious changes. The obtained electrospun PELA-P membranes exhibited self-accelerated biodegradability and could benefit drug controlled release and tissue regeneration.     

Influence of various starch types on PCL/starch blends anaerobic biodegradation

Research concentrated on the biodegradable capability of PCL blends with various types of starch in an anaerobic aqueous environment of mesophilic sludge from a municipal wastewater treatment plant. For blend preparation, use was made of a native starch Meritena from maize, another from Waxy – a genetically modified type of maize, as well as Gel Instant, a gelatinized starch, and an amaranth starch. Additional PCL/starch blends were prepared from the same starch types, but these were initially plasticized with glycerol. The biodegradability tests were supplemented with thermo gravimetric analysis (TGA), and differential scanning calorimetry (DSC); morphology was identified using scanning electron microscopy (SEM), plus mechanical properties were also tested. While mixtures of PCL with starches plasticized with glycerol exhibited improved mechanical properties and a higher degree of biodegradation in the anaerobic environment, mixtures of PCL with pure forms of starch were ascertained as rather resistant to the anaerobic aqueous environment. TGA and DSC analysis confirmed the removal of starch and glycerol from the PCL matrix. SEM then proved these results through the absence of starch grains in the samples following anaerobic biodegradation.     

Properties of crosslinked polylactides (PLLA & PDLA) by radiation and its biodegradability

Crosslinked materials derived from poly(lactide) (PLA) have been produced by radiation modification in the presence of a suitable crosslinker (triallyl isocyanurate) (TAIC). The crosslinking structure introduced in PLA films has not only much improved the heat stability but also their mechanical properties. The properties of crosslinked samples are governed by crosslinking density and these improvement seemed to increase with radiation dose. This implied that the three dimensional networks have been introduced in material by radiation and the crosslinking density depended on the structure and length of PLA chains. Biodegradability of PLA was also determined by an enzymatic degradation test and burying in compost at 55 °C. Differing with PLLA, PDLA was insignificantly degraded by proteinase K. The degradation rate of PLA in compost was postponed with the introduction of crosslinks.     

The influence of biotic and abiotic factors on the rate of degradation of poly(lactic) acid (PLA) coupons buried in compost and soil

Poly(lactic) acid (PLA) is a compostable biopolymer and has been commercialised for the for the manufacture of short-shelf life products. As a result, increasing amounts of PLA are entering waste management systems and the environment; however, the degradation mechanism is unclear. While hydrolysis of the polymer occurs abiotically at elevated temperature in the presence of water, potential catalytic role for microbes in this process is yet to be established. In this study, we examined the degradation of PLA coupons from commercial packaging at a range of temperatures (25°, 37°, 45°, 50° and 55 °C) in soil and compost and compared with the degradation rates in sterile aqueous conditions by measuring loss of tensile strength and molecular weight (Mw). In addition, in order to assess the possible influence of abiotic soluble factors in compost and soil on degradation of PLA, degradation rates in microorganism-rich compost and soil were compared with sterile compost and soil extract at 50 °C. Temperature was determined to be the key parameter in PLA degradation and degradation rates in microorganism-rich compost and soil were faster than in sterile water at temperatures 45° and 50 °C determined by tensile strength and Mw loss. Furthermore, all tensile strength was lost faster after 30 and 36 days in microorganism-rich compost and soil, respectively, than in sterile compost and soil extract, 57 and 54 days, respectively at 50 °C. Significantly more Mw, 68% and 64%, was lost in compost and soil, respectively than in compost extract, Mw, 53%; and in soil extract, 57%. Therefore, degradation rates were faster in microorganism-rich compost and soil than in sterile compost and soil extract, which contained the abiotic soluble factors of compost and soil at 50 °C. These comparative studies support a direct role for microorganisms in PLA degradation at elevated temperatures in humid environments. No change in tensile strength or Mw was observed either 25° or 37 °C after 1 year suggesting that accumulation of PLA in the environment may cause future pollution issues.     

Synthesis and biodegradation studies of 1,3-propanediol based aliphatic poly(ester carbonate)s

A series of poly(ester carbonate)s were obtained from adipic acid, 1,3-propanediol and diethyl carbonate in the presence of catalyst Ti(OBu)₄ by polycondensation and transestrification process. The amount of monomeric composition was varied in order to get the polymer of different composition. The structure, average molecular weight and physical properties of poly(ester carbonate) were characterized by FT-IR, ¹H NMR, solubility, solution viscosity, gel permeation chromatography, differential scanning calorimetry and XRD analysis. Biodegradability of poly(ester carbonate)s was investigated by hydrolytic (pH 7.2 and 11.5), enzymatic using Rhizopus delemar lipase at 37 °C and soil burial test. The biodegradation rate observed was more for poly(ester carbonate) containing 40% and 10% of diethyl carbonate due to their low crystallinity.     

Pressurised hot water extraction followed by simultaneous derivatization and headspace solid-phase microextraction and gas chromatography-tandem mass spectrometry for the determination of aliphatic primary amines in sewage sludge

In this paper we describe an environmentally friendly and sensitive method for the determination of ten primary amines in sewage sludge. The method is based on pressurised hot water extraction (PHWE) followed by simultaneous derivatization with pentafluorobenzaldehyde (PFBAY) and headspace solid-phase microextraction (HS-SPME) and subsequent gas-chromatography ion-trap tandem mass spectrometry (GC-IT-MS-MS) analysis. The influence of the main factors on the PHWE of sludge was optimized by a central composite design. For all species the optimal conditions were water at pH 4 as the extracting solvent, an extraction temperature of 100 °C and an extraction time of 15 min. The separation and detection of the ten amines by GC-IT-MS-MS took just 10 min and the entire process took approximately 1 h. Repeatability and reproducibility between days, expressed as RSD (%) (n = 5), were less than 19 and 24%, respectively. The average limit of detection (LOD) was of 65 μg kg⁻¹ s (range found 9-135) and the average limit of quantification (LOQ) was of 230 μg kg⁻¹ (range found 50-450) of dry weight (d.w.). Under optimized conditions we used this method to determine the compounds in industrial and municipal sewage sludge samples and in sludge from a potable water treatment plant. Methylamine and isobutylamine showed the highest levels in one of the industrial sewage sludge samples (404 and 543 mg kg⁻¹ (d.w.), respectively). To our knowledge, this paper presents for the first time the determination of ten primary amines in sewage sludge samples using PHWE.     

Oxidation and biodegradation of polyethylene films containing pro-oxidant additives: Synergistic effects of sunlight exposure, thermal aging and fungal biodegradation

Synergistic effects of sunlight exposure, thermal aging and fungal biodegradation on the oxidation and biodegradation of linear low density poly(ethylene) PE-LLD films containing pro-oxidant were examined. To achieve oxidation and degradation, films were first exposed to the sunlight for 93 days during the summer months followed by their incubation with fungal strains previously isolated from the soil based on the ability to grow on the oxidized PE-LLD as a sole carbon source. Some films were also thermally aged at temperatures ranging between 45°C and 65 °C, either before or after fungal degradation. Films with pro-oxidant additives exhibited a higher level of oxidation as revealed by increase in their carbonyl index (COi). In addition to increase in the COi, films showed a slight increase in crystallinity and melting temperature (T_m), considerably lower onset degradation temperatures, and a concomitant increase in the % weight of the residues. The level of oxidation observed in thermally aged films was directly proportional to the aging temperature. The PE-LLD films with pro-oxidant exposed to sunlight followed by thermal aging showed even higher rate and extent of oxidation when subsequently subjected to fungal biodegradation. The higher oxidation rate also correlated well with the CO₂ production in the fungal biodegradation tests. Similar films oxidized and aged but not exposed to fungal biodegradation showed much less degradation. Microscopic examination showed a profuse growth and colonization of fungal mycelia on the oxidized films by one strain, while another spore-producing strain grew around the film edges. Data presented here suggest that abiotic oxidation of polymer's carbon backbone produced metabolites which supported metabolic activities in fungal cells leading to further biotically-mediated polymer degradation. Thus, a combined impact of abiotic and biotic factors promoted the oxidation/biodegradation of PE-LLD films containing pro-oxidants.     

A Tucker model based approach for analysis of complex oil biodegradation data

A novel method based on gas chromatography–mass spectrometry in selected ion monitoring mode (GC–MS/SIM) and Tucker models is developed to evaluate the effects of oil type, microbial treatments and incubation time on the biodegradation of petroleum hydrocarbons. The data set consists of sections of the m/z 180, 192 and 198 GC–MS/SIM chromatograms of oil extracts from a biodegradation experiment where four oil types were exposed to four microbial treatments over a period of one year. The chosen sections, which are specific to methylfluorenes, phenanthrenes and dibenzothiophenes, were combined in a 4-way array (incubation time × oil type × treatment × combined chromatographic retention times) that was analyzed using both principal component analysis and the Tucker model. Several conclusions could be reached: the light fuel oil was the least degradable of those tested, 2- and 3-methyl isomers were more easily degraded compared to the 4-methyl isomers, the mixture of surfactant producers and PAC degraders provided the most effective degradation and the largest part of the degradation occurred between 54 and 132 days.     

H2O + Fe(NO3)3 + Ni(NO3)2 ternary system isotherms at 0 °C and 30 °C

H₂O + Ni(NO₃)₂ binary system were investigated in the temperature range from −25 °C to 55 °C. The solid-liquid equilibria of the ternary system H₂O + Fe(NO₃)₃ + Ni(NO₃)₂ were studied using a synthetic method based on conductivity measurements. Tow isotherms were established at 0 °C and 30 °C, and the appearing stable solid phases are iron nitrate nonahydrate (Fe(NO₃)₃·9H₂O), iron nitrate hexahydrate (Fe(NO₃)₃·6H₂O), nickel nitrate hexahydrate (Ni(NO₃)₂·6H₂O) and nickel nitrate tetrahydrate (Ni(NO₃)₂·4H₂O).     

Preparation, characterization, swelling and in vitro drug release behaviour of poly[N-acryloylglycine-chitosan] interpolymeric pH and thermally-responsive hydrogels

Novel biodegradable pH- and thermal-responsive interpenetrating polymer network (IPN) hydrogels were prepared for controlled drug delivery studies. The IPN hydrogels were obtained in mild aqueous acid media by irradiation of solutions of N-acryloylglycine (NAGly) mixed with chitosan, in the presence of glutaraldehyde as a crosslinking agent and using 2,2-dimethoxy-2-phenyl acetophenone as photoinitiator. These hydrogels were subjected to equilibrium swelling studies at different temperatures (25 °C, 37 °C and 45 °C) in buffer solutions of pH 2.1 and 7.4 (similar to that of gastric and intestinal fluids respectively). 5-Fluorouracil (5-FU) was entrapped in the hydrogels, and drug release studies carried out at 37 °C in buffer solutions at pH 2.1 and 7.4.     

Novel evaluation method of biodegradabilities for oil-based polycaprolactone by naturally occurring radiocarbon-14 concentration using accelerator mass spectrometry based on ISO 14855-2 in controlled compost

The biodegradabilities of poly(?-caprolactone) (PCL) powders (av. size = 180.7 μm) in controlled compost at 58 °C have been studied using the microbial oxidative degradation analyzer (MODA) based on ISO 14855-2 entitled “Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions - Method by analysis of evolved carbon dioxide - Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test”. The biodegradability of the PCL powders was 101.4% in a 56-day test period by the ISO method. The biodegradabilities of PCL powders have been studied using percent modern carbon (pMC) measured by accelerated mass spectrometry (AMS). Trapped CO₂ was analyzed by AMS to determine the pMC (sample) using ¹⁴C radiocarbon concentration. By using the theory that the pMC (sample) was the sum of pMC (compost) (104.88%) and pMC (PCL) (0%) as the respective ratios in the determined period, CO₂ (respiration) was calculated only from one reaction vessel. The biodegradability of PCL powders was 79.9% in a 56-day test period by the AMS method. It was found that respiration activities in the sample vessel including PCL, compost and sea sand were the same as that in the blank vessel including compost and sea sand without PCL during the active biodegradation period (0-33 day) at 58 °C. It was confirmed that respiration activities in the sample vessel were slightly higher than that in the blank vessel after active biodegradation due to the propagation of microorganisms using energy and metabolites by PCL biodegradation during those periods.     

Hydrolytic aging of crystallizable shape memory poly(ester urethane): Effects on the thermo-mechanical properties and visco-elastic modeling

The shape memory functionality of a segmented poly(ester urethane) and its hydrolytically aged specimens has been studied by cyclic thermo-mechanical measurements with an imposed strain of 100%. The shape memory effect was triggered by a melting transition in the soft segment phase. Aging was enforced by immersion in hot de-ionized water. In the course of the immersion the tensile properties (secant moduli, stress and strain at yield and break) were impaired by hydrolysis. Advanced specimen embrittlement finally led to rupture during the first thermo-mechanical cycle. This happened after 68 days of aging at 55 °C and correspondingly after 8 days at 80 °C. The residual strain after the first cycle, which was about 25%, increased significantly with aging time. Therefore, the total strain recoverability became ever smaller: aged specimens needed conditioning by at least two cycles for a full development of shape recoverability. Likewise the recovery force decreased continuously. Despite these degradation effects, it was observed that the shape fixity and the cycle-related shape recovery of appropriately conditioned specimens (number of cycles N > 2) remained on a constant high level (at round 100% and between 90% and 100%, respectively) throughout the whole aging period. These observations are discussed within the framework of a simplified model of the behavior of crystallizable shape memory polymers. The amorphous state of the polymer is described by the equation of the linear visco-elastic solid. As for the semi-crystalline state the material is assumed to react elastically with respect to deviations from the configuration, which was frozen up under constraint conditions. The curves of the dependence of the material behavior on aging time at 55 °C match perfectly those at 80 °C when the time axis is adjusted by a factor of 8.5, from which the apparent activation energy for hydrolytic aging in the amorphous state of 82 kJ mol⁻¹ could be deduced.     

Acetylene-grafted resins derived from phenolics via azo coupling reaction

Novel phenolic resins with high ethynyl contents were realized via azo coupling reaction between phenol units and diazonium of 3-ethynylaniline. If Novolac and high-ortho Novolac resins were used as the starting materials directly, the ratio of ethynyl groups to phenolic rings was ca 70%; while the ratio was 100% for the resin from Friedel-Craft polycondensation of 4-(3-ethynylphenyl)salicyl alcohol. All the resins were readily soluble in acetone and ethanol, and meltable at temperatures below 100 °C. The resins underwent thermal addition-type cure with a broad exotherm of around 140-280 °C, and the starting curing temperature showed a downward drift with increase in the ethynyl content. The thermal properties of the cured resins, determined from thermogravimetric analysis (TGA), were considerably superior to those of Novolac- and Resole-type phenolic resins. The initial decomposition temperatures were at ca 400 °C, and the anaerobic carbon yields were ca 80% for all the resins.     

Alkaline extraction in combination with microwave-assisted extraction followed by solid-phase extraction treatment for polycyclic aromatic hydrocarbons in a sediment sample

Microwave-assisted extraction using 1 M KOH/methanol (alkaline-MAE) in combination with solid-phase extraction treatment was developed and applied to polycyclic aromatic hydrocarbons (PAHs) in a sediment sample. Although various conditions were examined (100 or 150 °C for 10 or 30 min), comparable concentrations of PAHs to those obtained by conventional extraction with 1 M KOH/methanol at 70 °C for 4 h were obtained, even at 100 °C for 10 min. The concentrations obtained by using MeOH at 150 °C for 30 min without KOH were lower (by 1.3-37%) than those obtained by alkaline-MAE at 150 °C for 30 min. Since the developed technique can introduce higher concentration of benzo[ghi]perylene relative to those using pressurized liquid extraction (toluene, 150 °C, 15 MPa, 10 min, two cycles), the developed alkaline-MAE is a effective technique.     

Thermal decomposition of the vivianite arsenates—implications for soil remediation

The presence of arsenate compounds in soils and mineral dump leachates is common. One potential method for the removal of the arsenates from soils is through thermal treatment. High-resolution thermogravimetric analysis has been used to follow this thermal decomposition of selected vivianite arsenates. This decomposition occurs as a series of steps. The first two steps involve dehydration with 6 mol of water lost in the first step and two in the second. The third major weight loss step occurs in the 750-800 °C temperature range with de-arsenation. The application of infrared emission spectroscopy confirms the loss of water by around 250 °C and the loss of arsenic as arsenic pentoxide is observed by the loss of AsO stretching bands at around 826 cm⁻¹. Thermal activation of arsenic contaminated soils may provide a method of decontamination.     

The preparation of HCF2CdX and HCF2ZnX via direct insertion into the carbon halogen bond of CF2HY (Y = Br, I)

The difluoromethylcadmium and zinc reagents have been prepared in DMF via direct insertion of Cd⁰ into the carbon halogen bond of CF₂HY (Y = Br, I). These reagents are stable at 65-75 °C and exhibit prolonged stability and activity at room temperature. Metathesis of the difluoromethylcadmium reagents with Cu(I)X (X = Br, Cl) at −55 °C rapidly produces difluoromethylcopper. The copper reagent is significantly less stable than the cadmium or zinc reagent and rapidly decomposes at room temperature. The difluoromethylcadmium and copper reagents exhibit good reactivity with allylic halides, propargylic derivatives and 1-iodoalkynes to provide good yields of the corresponding difluoromethylalkenes, difluoromethylallenes and difluoromethyl-2-alkynes. Alkylation is successful only with reactive alkyl halides. Generally, the difluoromethylcopper reagent is more reactive than the difluoromethylcadmium reagent and generally exhibits higher regioselectivity in reactions that can occur by either α- or γ-attack.