Novel aromatic poly(amide-hydrazide)s based on the bipyridine. Part I: Synthesis, characterization and thermal stability

A series of new poly(amide-hydrazide)s were obtained by the direct polycondensation of 5-amino 5′-carbohydrazido-2,2′-bipyridine with commercially available diacids by means of triphenyl phosphite and pyridine in the N-methyl-2-pyrrolidone (NMP) solutions containing dissolved LiCl. The resulting hydrazide containing polymers exhibited inherent viscosities in the 0.42-0.64 dL/g range. All copolymers were soluble in polar solvents such as NMP and dimethyl sulfoxide (DMSO). Most of the amorphous hydrazide copolymers formed flexible and tough films by solvent casting. The poly(amide-hydrazide)s had glass-transition temperatures (T_g) between 178 and 206 °C. All hydrazide copolymers could be thermally converted into the corresponding poly(amide-oxadiazole) approximately in the region of 300-400 °C, as evidenced by the DSC thermograms. The oxadiazole polymers and copolymers showed a dramatically decreased solubility and higher T_g when compared to their respective hydrazide prepolymers. They exhibited T_gs of 197-248 °C and were stable up to 450 °C in air or nitrogen.     

Thermal and rheological behaviours of some random aromatic amino-ended polyethersulfone/polyetherethersulfone copolymers

The thermal and rheological characterizations of seven random, low molecular weight (M_n ≅ 9500 g mol⁻¹), H₂N-ended polyethersulfone/polyetherethersulfone (PES/PEES) copolymers, at various PES/PEES ratios, were performed. The glass transition temperatures (T_g) were determined by DSC. Degradations were carried out in a thermobalance, under flowing nitrogen, in dynamic heating conditions from 35 °C to 650 °C. The initial decomposition temperatures (T_i) and the half decomposition temperatures (T_1/2) were directly determined by TG curves, while the apparent activation energies of degradation (E_a) were obtained by the Kissinger method. In addition, the complex viscosities (η^∗) of the molten polymers were determined in experimental conditions of linear viscoelasticity. T_g, E_a and η^∗ values increased linearly with PES% content, while T_i and T_1/2 values showed opposite behaviour. In every case both PES and PEES homopolymers felt outside linearity. The results obtained are discussed and interpreted, and compared with those of corresponding Cl-ended copolymers previously studied.     

Mechanical and thermal properties of perfluoroalkyl ethyl methacrylate-methyl methacrylate statistical copolymers synthesized in supercritical carbon dioxide

Poly(methyl methacrylate-ran-perfluoroalkyl ethyl methacrylate) copolymers having varying perfluoroalkyl ethyl methacrylate ester (Zonyl-TM) contents were synthesized in supercritical CO₂. Complete amorphous structures of the copolymers were verified by XRD. Young's modulus (Y_mod) of the copolymers was decreased linearly from 1.57 to 1.08 GPa and T_g values from 102 to 77 °C with the increase of Zonyl-TM content. A linear relationship between the Y_mod and the T_g values of the copolymer was also found. The increase of the large branched pendant groups resulted in the increase of the free volume and a corresponding decrease in Y_mod and T_g of the copolymers. A good fit was found when the Schneider equation was used. Negative deviation from the Gordon-Taylor equation was observed when Zonyl-TM content was lower than 14% due to rapid increase in free volume and then a positive deviation was found due to the dipole-dipole interactions between the methyl ester and fluoroalkyl ester groups.     

Synthesis of hyperbranched-linear star block copolymers by atom transfer radical polymerization of styrene using hyperbranched poly(siloxysilane) (HBPS) macroinitiator

Hyperbranched-linear star block copolymers, hyperbranched poly(siloxysilane)-block-polystyrene (HBPS-b-PSt), were prepared by atom transfer radical polymerization (ATRP) of styrene in xylene, using bromoester-terminated HBPS (HBPS-Br (P3), M_n = 7500, M_w/M_n = 1.76) as a macroinitiator. The number-average molecular weights of the obtained polymers (M_n) were in the range of 21,800-60,000 and molecular weight distributions were unimodal throughout the reaction (M_w/M_n = 1.28-1.40). These polymers showed 5 wt.% decomposition temperature (T_d5) over 300 °C. The DSC thermograms of the resulting polymers indicated two glass transition temperatures (T_g). The T_g of HBPS segment shifted to higher value while the T_g of PSt segment shifted to lower value compared with those of the homopolymers. Preliminary physical characterization related to the solution viscosity of the resulting block copolymers is also reported.     

New fluorinated polymers bearing pendant phosphonic groups for fuel cell membranes: Part 1 synthesis and characterizations of the fluorinated polymeric backbone

Radical copolymerizations of chlorotrifluoroethylene (CTFE) with vinyl ethers such as 2-chloroethyl vinyl ether (CEVE) and ethyl vinyl ether (EVE) were performed at 75 °C in the presence of peroxide initiator. Three copolymers were obtained and characterized by means of both NMR and elemental analysis. Then, the chlorine atoms in the side chains were converted into iodine atoms by nucleophilic substitution, which was monitored by ¹H NMR spectroscopy. A series of five copolymers with different amounts of iodine atoms in the side chains were thus obtained. These copolymers exhibited molecular weight values of about 25,000 g mol⁻¹, and the thermal analysis of the copolymers showed a starting degradation from about 220 °C. The T_g values were in the range of 34-41 °C and showed a linear dependence versus the content of iodine atoms.     

Photoinduced optical anisotropy in azobenzene methacrylate block copolymers: Influence of molecular weight and irradiation conditions

The photoinduced anisotropy in a series of azomethacrylate block copolymers with different molecular weights and azo contents has been investigated under several irradiation conditions. Depending on molecular weight and composition, different microstructures (disordered, lamellar, spherical) appear, due to block microsegregation. Measurements of birefringence (Δn) induced with linearly polarised 488 nm light show that the highest (and stable) Δn_N values (birefringence normalised to the azo content) are achieved in copolymers with a lamellar structure. Lower Δn_N are obtained in the copolymers in which azobenzene units segregate to nano spheres and the lowest (and less stable) Δn_N values, appear in disordered systems not showing any defined microstructure. Besides, higher Δn_N is obtained in the copolymers with larger molecular weight of the poly (methyl methacrylate) and the azo polymer blocks, both in the microspheres segregated polymers as well as in those without a clear microstructure. This behaviour is consistent with that of the photoinduced order of azobenzene units obtained from dichroism measurements. Irradiation temperature (from 30 to 90 °C) and light power (from 100 to 500 mW/cm²) also influence the photoinduced response. Photoinduced Δn_N growth rate is faster when both temperature and irradiation power increase. Furthermore, birefringence is only induced at temperatures up to 90 °C, the maximum value being obtained at about 70 °C. No clear dependence of the final Δn_N value with light power has been found.     

Phase behavior of biodegradable amphiphilic poly(l,l-lactide)-b-poly(ethylene glycol)-b-poly(l,l-lactide)

This study describes the miscibility phase behavior in two series of biodegradable triblock copolymers, poly(l-lactide)-block-poly(ethylene glycol)-block-poly(l-lactide) (PLLA-PEG-PLLA), prepared from two di-hydroxy-terminated PEG prepolymers (M_n = 4000 or 600 g mol⁻¹) with different lengths of poly(l-lactide) segments (polymerization degree, DP = 1.2-145.6). The prepared block copolymers presented wide range of molecular weights (800-25,000 g mol⁻¹) and compositions (16-80 wt.% of PEG). The copolymer multiphases coexistance and interaction were evaluated by DSC and TGA. The copolymers presented a dual stage thermal degradation and decreased thermal stability compared to PEG homopolymers. In addition, DSC analyses allowed the observation of multiphase separation; the melting temperature, T_m, of PLLA and PEG phases depended on the relative segment lengths and the only observed glass transition temperature (T_g) in copolymers indicated miscibility in the amorphous phase.     

New unsaturated polyesters as injectable drug carriers

New unsaturated polyesters of poly(fumaric acid-glycol-sebacic acid) copolymers and poly(maleic anhydride-glycol-sebacic acid) copolymers were prepared by melt polycondensation of the corresponding mixed monomers: sebacic anhydride, fumaric acid or maleic anhydride and glycol. Methyl-methacrylate (MMA) was used as crosslinker and dimer acid was used as thinner.In vitro studies showed that those copolymers are degradable in phosphate buffer at 37 °C and poly(fumaric acid-glycol-sebacic acid) has proper drug release rate as drug carriers. The biocompatibility of poly(fumaric acid-glycol-sebacic acid) copolymers under mice skin was also evaluated; macroscopic observation and microscopic analysis demonstrated that the copolymer is biocompatible and well tolerated in vivo. The injected poly(fumaric acid-glycol-sebacic acid) [molar ratio M_{fumaric acid}:M_glycol:M_{sebacic acid} = 1.75:2.20:0.25] containing 5% adriamycin hydrochloride (ADM) in the mice bearing Sarcoma-180 tumor exhibited a good antitumor efficacy. The volume doubling time (VDT) (18 ± 2.5 days) of the tumor growth by this treatment was longer than that (7 ± 0.9 days) by the subcutaneous injection of ADM.     

Self-assembly and aggregation of ATRP prepared amphiphilic BAB tri-block copolymers contained nonionic ethylene glycol and fluorescent 9,10-di(1-naphthalenyl)-2-vinyl-anthracene/1-vinyl-pyrene segments

Two novel amphiphilic BAB-type block copolymers, ADN-PEG3400-ADN and Py-PEG3400-Py containing deep blue and bluish-green fluorescent moieties were prepared using atom transfer radical polymerization (ATRP) (where, ADN = poly(9,10-di(1-naphthalenyl)-2-vinylanthracene), Py = poly(1-vinyl pyrene) and PEG3400 = poly(ethylene glycol) with M_n = 3400 g/mol). The GPC number averaged molecular weights (MW) of the block copolymers were M_n = 9600 and 13,800 g/mol, respectively, based on polystyrene MW standards. The PEG3400 segment has a melting temperature (T_m peak) at 64–65 °C, whereas the glass transition temperatures (T_g midpoint) of the ADN and Py segments were found to be 230 °C and 193 °C, respectively, and are similar to their respective homopolymers indicating complete microphase segregration. The photoluminescence (PL) emission of the copolymers ADN-PEG3400-ADN exhibited two maxima at 423.5 nm and 441.5 nm while Py-PEG3400-Py has a maximum at 488.5 nm. Both copolymers form individual spherical micelles with diameter from 30 to 90 nm for Py-PEG3400-Py and 40–160 nm for ADN-PEG3400-ADN. The micelles, however, transform into cross-linked pearl-necklace-like aggregates at polymer concentrations above 1000 ppm, which may be attributed to the physical cross-linking between adjacent spherical micelles caused by the PEG3400 segments.     

Synthesis and properties of poly(aryl ether benzimidazole) copolymers for high-temperature fuel cell membranes

A series of poly(aryl ether benzimidazole) copolymers bearing different aryl ether linkage contents were synthesized by condensation polymerization in polyphosphoric acid (PPA) by varying the feed ratio of 4,4′-dicarboxydiphenyl ether (DCPE) to terephthalic acid (TA). As the ether unit content in the copolymer increased, the solubility of the copolymer in PPA and N,N′-dimethylacetamide/LiCl improved. For example 3–7 wt.% DMAc solution containing 2 wt.% of LiCl could be prepared from the copolymers. XRD studies revealed that the incorporation of flexible aryl ether linkages increased the chain d-spacings of the polymer backbones and decreased the crystallinity of the copolymers. Still, these copolymers having ether linkages showed reasonably good thermal/mechanical stability and high proton conductivity. For example, the copolymer with 30 mol% ether linkage had a tensile strength of 43 MPa (at 26 °C and 40% relative humidity) at an acid doping level of 7.5 mol H₃PO₄ and a proton conductivity of 0.098 S cm⁻¹ (at 180 °C and 0% relative humidity) at an acid doping level of 6.6 mol H₃PO₄.     

Synthesis and characterization of amorphous poly(ethylene terephthalate) copolymers containing bis[4-(2-hydroxyethoxy)phenyl]sulfone

Poly(ethylene terephthalate) copolymers (abbreviated as PETS) that contain bis[4-(2-hydroxyethoxy)phenyl]sulfone (BHEPS) were prepared from dimethyl terephthalate (DMT), ethylene glycol (EG) (5-95%) and BHEPS (5-95%). The compositions and microstructures of the copolyesters were determined by ¹H and ¹³C nuclear magnetic resonance (NMR) spectroscopy, respectively. The thermal behaviors were studied over the entire range of copolymer compositions, using X-ray analysis, differential scanning calorimeter (DSC) and thermogravimetric analysis (TGA). The molecular weights, optical characteristics and tensile properties of these polymers were also determined. Experimental results indicated that the copolymers had a random microstructure. The intrinsic viscosities of the copolymers ranged from 0.65 to 0.69 dL/g. The copolyesters with BHEPS of <10 mol% were crystallizable, whereas the copolyesters with BHEPS of ?10 mol% were amorphous. Incorporating BHEPS affected the glass-transition temperature (T_g) values of those polymers, from about 81 °C for PETS₅ to 126 °C for PETS₉₅. The optical transmissions exceeded 86% for λ = 400 nm for all of the amorphous polyesters. The tensile modulus and strength of the copolyesters increased with BHEPS. However, they also became brittle and their elongation at break decreased.     

Thermal and rheological behaviour of some random aromatic polyethersulfone/polyetherethersulfone copolymers

The thermal and rheological behaviour of seven random Cl-ended aromatic PES/PEES copolymers (M_n ≈ 9500 g mol⁻¹), at various PES/PEES repeating unit ratios, was studied. The glass transition temperatures (T_g), determined by DSC experiments, showed a dependence on copolymer composition significantly different from the ideal linear behaviour expected on the basis of Fox equation. Degradations were carried out in the scanning mode, under flowing nitrogen, in the temperature range 35-650 °C and a single degradation stage was observed for all copolymers. The initial decomposition temperatures (T_i) and the half decomposition temperatures (T_1/2) were directly determined by TG curves, while the apparent activation energies of degradation (E_a) were obtained by the Kissinger method. In addition, the complex viscosity (η^∗) of molten copolymers was determined in experimental conditions of linear viscoelasticity. T_i, T_1/2, E_a, and η^∗ values were depending on copolymer composition, showing a trend similar to that of T_g values. The results obtained were discussed and interpreted.     

Thermodynamics of dimethylene urethane and poly(dimethylene urethane) in the range from T → 0 to 490 K at standard pressure

By high-precision dynamic calorimetry the temperature dependences of heat capacity of dimethylene urethane (DMU) between 320 and 370 K and partially crystalline poly(dimethylene urethane) (PDMU) in the range 326-490 K at standard pressure have been determined within ±1.5%. The thermodynamic characteristics of fusion of the substances, namely the temperature interval of melting, temperature, enthalpy and entropy of fusion, as well as the characteristics of devitrification and glassy state for poly(dimethylene urethane) have been estimated. The first and the second cryoscopic constants have been calculated for dimethylene urethane. The experimental data obtained in the present work and literature findings on the heat capacity of the substances were used to calculate their thermodynamic functions: the heat capacity C°_p (T), enthalpy H°(T)−H°(0), entropy S°(T) and Gibbs function G°(T)−H°(0) over the range from T→0 to (370-480) K. Based on the data, the thermodynamic characteristics of polymerization process with five-membered ring opening Δ_polH°, Δ_polS° and Δ_polG° of dimethylene urethane with the formation of linear partially crystalline poly(dimethylene urethane) have been evaluated.     

Dielectric behaviour of copolymers based on 2,2,2-trifluoroethyl methacrylate and cyano co-monomers

In the frame of a research aiming at developing new dielectric polymers containing CCN and CF substituents with strong dipole moment, statistical copolymers based on cyano monomers such as acrylonitrile (AN), methacrylonitrile (MAN), methylvinylidene cyanide (MVCN) and 2,2,2-trifluoroethylmethacrylate (MATRIF), were synthesized and characterized. Elemental analysis has shown that the molar percentages of AN and MAN in the copolymers were 45 mol.%, while only 5 mol.% of MVCN was incorporated in the poly(MVCN-co-MATRIF) copolymer. These copolymers exhibit glass transition temperatures, T_g, in the range of 70-90 °C. The dynamic dielectric analyses and their complex permittivities of these copolymers were studied versus the temperature and the frequency. Evidence of an α-relaxation phenomenon in the glass transition region, which is confirmed by the Vogel-Fulcher-Tammann (VFT) temperature dependence of the relaxation times, was assigned to the cooperative reorientation motions of the cyano groups. The values of dielectric strength (Δε) for the copolymers based on MATRIF were determined by Havriliak-Negami (HN) fitting from the dispersion curves, and can be related to the polarity of the monomer unit and to the packing of the macromolecular chains. These relaxations are sometimes overlapped by conduction phenomena due to ionic impurities at low frequencies and high temperatures dipolar losses. In the glassy state, the permittivity values of AN and MAN copolymers show an increase of polarity which makes them candidates for some applications amongst advanced electrical materials such as dielectric layer for capacitors.     

One-pot, novel chemical modification of glycidyl methacrylate copolymers with very bulky organosilicon side chain substituents

Glycidyl methacrylate (GM) random copolymers with styrene and methylstyrene (in a 1:1 and 1:3 mole ratio) were synthesized by solution free radical polymerizations at 70 ± 1 °C using α,α′-azoisobutyronitrile as an initiator. The copolymer compositions were obtained using related ¹H NMR spectra and the polydispersity indices of the copolymers determined using gel permeation chromatography (GPC). Both types of polymer could be modified by incorporation of the highly sterically demanding tris(trimethylsilyl)methyl substituent (Me₃Si)₃C-(Tsi = trisyl) through the ring opening reaction of the epoxy groups in copolymers. Chemical modification was determined by ¹H NMR and infrared spectroscopies. The glass transition temperature T_g of all copolymers was determined by differential scanning calorimetry (DSC). The T_g value of the copolymers containing bulky trisyl groups was found to increase with incorporation of trisyl groups in polymer structures. The presence of trisyl groups in the polymer side chain created new macromolecules with novel modified properties and potential use as membranes for fluid separation.     

Synergistic effects of layered double hydroxide with hyperfine magnesium hydroxide in halogen-free flame retardant EVA/HFMH/LDH nanocomposites

The synergistic effects of layered double hydroxide (LDH) with hyperfine magnesium hydroxide (HFMH) in halogen-free flame retardant ethylene-vinyl acetate (EVA)/HFMH/LDH nanocomposites have been studied by X-ray diffraction (XRD), transmission electron spectroscopy (TEM), thermogravimetric analysis (TGA), limiting oxygen index (LOI), mechanical properties' tests, and dynamic mechanical thermal analysis (DMTA). The XRD results show that the exfoliated EVA/HFMH/LDH can be obtained by controlling the LDH loading. The TEM images give the evidence that the organic-modified LDH (OM-LDH) can act as a disperser and help HFMH particles to disperse homogeneously in the EVA matrix. The TGA data demonstrate that the addition of LDH can raise 5-18 °C thermal degradation temperatures of EVA/HFMH/LDH nanocomposite samples with 5-15 phr OM-LDH compared with that of the control EVA/HFMH sample when 50% weight loss is selected as a point of comparison. The LOI and mechanical tests show that the LDH can act as flame retardant synergist and compatilizer to apparently increase the LOI and elongation at break values of EVA/HFMH/LDH nanocomposites. The DMTA data verify that the T_g value (−10 °C) of the EVA/HFMH/LDH nanocomposite sample with 15 phr LDH is much lower than that (T_g = −2 °C) of the control EVA/HFMH sample without LDH and approximates to the T_g value (−12 °C) of pure EVA, which indicates that the nanocomposites with LDH have more flexibility than that of the EVA/HFMH composites.     

Poly(methylmethacrylate-dimethylsiloxane) triblock copolymers synthesized by transition metal mediated living radical polymerization: bulk and surface characterization

Well-defined poly(MMA-b-DMS-b-MMA) triblock copolymers were prepared by copper(I) mediated living radical polymerization. This was achieved by polymerization of methylmethacrylate (MMA) with different concentrations of 2-bromoisobutyrate terminated polydimethylsiloxane (PDMS). The polymerization occurred in controlled manner with the molecular weight found by ¹H NMR close to that predicted and a narrow molecular weight distribution (M_w/M_n∼1.2). Copolymers were obtained with M_n=2100, 4900, 10 100 and 29 500 g mol⁻¹ respectively with poly(MMA) (PMMA) terminal blocks and a central PDMS block of 5500 g mol⁻¹ in each case.DSC analysis showed most of the poly(MMA-b-DMS-b-MMA) triblock copolymers exhibits two T_g’s, one at low temperature corresponding to the T_g of PDMS microphase and a second at high temperature corresponding to the T_g of the PMMA microphase. TEM images show microphase segregation morphology in bulk for the triblock copolymers, with a higher degree of segregation for copolymers containing higher PDMS content. XPS measurements were performed to determine the chemical composition at the surface. For all the copolymers PDMS enrichment is observed at the surface. Copolymers containing higher percentage of PDMS exhibit higher phase separation and better enrichment of PDMS at the surface. The surface tension determined by contact angle measurements of the copolymer film containing 59 mol% of PDMS was 19.15 mN m⁻¹.     

Novel fluoroacrylated copolymers: synthesis, characterization and properties

The development of polymer waveguides leads to synthesis of fluorinated amorphous polymers with high transmission capacity, potential to tune their optical properties by tailoring the molecular structure, together with good processability, easy handling, good flexibility and low cost.In this work we have investigated new thermoplastic fluoroacrylated copolymers, synthesized by radical copolymerization of fluoroalkene(s) with five-membered cyclic carbonate and a third monomer or transfer agent, both containing OH group susceptible to be used for grafting of photocrosslinkable groups. The reaction of hydroxy functionalized copolymers with different acrylating agents results in fluoroacrylated resins with molecular weight in the range of 2000-3000 g mol⁻¹, yield >75% and good solubility in reactive diluents. In the presence of photoinitiator(s), they were crosslinked under UV-radiation in order to obtain optical waveguides.The copolymers synthesized were characterized by ¹H, ¹⁹F and ¹³C NMR as well as FT-IR spectroscopies and have good thermal stability (T_d > 200 °C). The refractive indeces of hydroxy functionalized fluorooligomers and acrylated resins were found to range from 1.44 to 1.45 at 23 °C and the T_gs (by DSC) varied from 40 to 110 °C depending on the content of the cyclic monomer. The optical characteristics of these thermoplastic fluoroacrylated copolymers are under progress.     

Synthesis and phase separation of amine-functional temperature responsive copolymers based on poly(N-isopropylacrylamide)

Free radical copolymerizations of N-isopropyl acrylamide (NIPAM) and cationic N-(3-aminopropyl) methacrylamide hydrochloride (APMH) were investigated to prepare amine-functional temperature responsive copolymers. The reactivity ratios for NIPAM and APMH were evaluated in media of different ionic strength (r_NIPAM = 0.7 and r_APMH = 0.7-1.2). Phase separation behavior of the random copolymers with only 5 mol% of the APMH was found to be suppressed in pure water at temperatures up to 45 °C due to electrostatic repulsion among the cationic amine groups randomly distributed along the copolymer chain. Alternate sequential addition of PNIPAM/APMH mixtures and pure NIPAM was used to provide increased control of the location of APMH units along the chain. Consequently (close to) homo-PNIPAM block(s) were formed as evidenced by its characteristic phase transition at 33 °C. The influences of the monomer feeding time and feeding interval time to the APMH distribution were investigated to prepare copolymers with thermo-induced phase separation under physiologically relevant temperature and to determine the extent of conjugation to poly(ethylene oxide).     

Synthesis of poly(4-vinylpyridine) and block copoly (4-vinylpyridine-b-styrene) by atom transfer radical polymerization using 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazamacrocyclotetradecane as ligand

Poly(4-vinylpyridine) (P4VP) and block copolymer, poly(4-vinylpyridine-b-styrene) (P4VP-b-PSt) were prepared by atom transfer radical polymerization (ATRP) using 1-phenylethyl chloride as initiator, CuCl and 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazamacrocyclotetradecane (Me₆[14]aneN₄) as catalyst and ligand. The polymerization of 4VP was carried out in 2-propanol at 40 °C. GPC and NMR studies show that the plot of ln([4VP]₀/[4VP]) against the reaction time is linear, and the molecular weight of the resulting P4VP increased linearly with the conversion. Within 3 h, the conversion can reach almost 90%. P4VP-b-PSt amphiphilic block copolymer with low polydispersity index (M_w/M_n ≈ 1.2) is also obtained by ATRP of St in DMF at 110 °C using P4VP-Cl as macroinitiator, CuCl/ Me₆[14]aneN₄ as catalyst.