Morphology and mechanical properties of extruded ribbons of LDPE/PA6 blends compatibilized with an ethylene-acrylic acid copolymer

Two grades of low density polyethylene (LDPE) were blended with polyamide-6 (PA) in the 75/25 and 25/75 wt/wt ratios and shaped into ribbons with a Brabender single screw extruder. An ethylene-acrylic acid copolymer (EAA) was used in the 2 phr concentration as a compatibilizer precursor (CP). The morphology of the ribbons and its evolution during high temperature annealing were investigated by scanning electron microscopy (SEM). The results confirmed that EAA does actually behave as a reactive compatibilizer for the LDPE/PA blends. In fact, in the presence of EAA, the interfacial adhesion is improved, the dispersion of the minor phase particles is enhanced and their tendency toward fibrillation is increased, especially for the blends with the higher molar mass LDPE grade. The mechanical properties of the latter blends were found to be considerably enhanced by the addition of EAA, whereas the improvement was relatively modest for the blends with the lower molar mass LDPE. The fracture properties of double end notched samples of the ribbons prepared with the blends containing the lower molar mass LDPE grade were also studied. It was shown that, despite of the increased interfacial adhesion caused by the presence of EAA, the latter plays a measurable positive effect on the fracture properties only for the blends with LDPE as the matrix.     

含二烯丙基双酚A醚相容剂对HDPE/PC共混体系的影响

用低密度聚乙烯接枝二烯丙基双酚Ａ醚（ＬＤＰＥ ｇ ＤＢＡＥ）作为高密度聚乙烯／聚碳酸酯（ＨＤＰＥ／ＰＣ）共混体系的增容剂,研究了其对ＨＤＰＥ／ＰＣ共混体系的影响．通过共混物形态观察、热力学性能测试和结晶性分析,发现ＬＤＰＥ ｇ ＤＢＡＥ对ＨＤＰＥ／ＰＣ共混体系有良好的增容效果．并发现了增容剂在共混物中的最佳用量为１０ｐｈｒ,提高增容剂的接枝率更有利于改善共混物的性能     

Preparation and characterization of polyamide 6/polyethylene blend-clay nanocomposites in the presence of compatibilisers and stabilizing system

Several compatibilising systems were added to high-density polyethylene (HDPE) and polyamide 6 (PA6) blends in the presence of an organically modified montmorillonite (OMM). All the blends were prepared by using a co-rotating twin-screw extruder and characterized by SEM, TEM and XRD analyses. In addition, the rheological behaviour and the mechanical properties - tensile and impact - were evaluated.The presence of OMM affects the dimensions of the polymeric phases in the blend but not their mutual adhesion, granted only by the compatibilisers.TEM, SEM and XRD analyses indicated that there is a strict correlation between the compatibilisation level and the final interlayer distance achieved by OMM.Even if some filled compatibilised blends showed a fairly good morphology - in terms of phase adhesion, dispersion and dimension - the mechanical performance was not so satisfactory. These results were interpreted considering the possible thermo-oxidative degradation of the organic modifier of OMM and the subsequent interaction between and the degradation products and the compatibilising systems. In order to prevent these phenomena, a stabilizing system was added to the nanocomposite blends. In this case, an improvement of mechanical properties was achieved.     

Solid-state relaxations in linear low-density (1-octene comonomer), low-density,and high-density polyethylene blends

Extensive thermal and relaxational behavior in the blends of linear low-density polyethylene (LLDPE) (1-octene comonomer) with low-density polyethylene (LDPE) and high-density polyethylene (HDPE) have been investigated to elucidate miscibility and molecular relaxations in the crystalline and amorphous phases by using a differential scanning calorimeter (DSC) and a dynamic mechanical thermal analyzer (DMTA). In the LLDPE/LDPE blends, two distinct endotherms during melting and crystallization by DSC were observed supporting the belief that LLDPE and LDPE exclude one another during crystallization. However, the dynamic mechanical β and γ relaxations of the blends indicate that the two constituents are miscible in the amorphous phase, while LLDPE dominates α relaxation. In the LLDPE/HDPE system, there was a single composition-dependent peak during melting and crystallization, and the heat of fusion varied linearly with composition supporting the incorporation of HDPE into the LLDPE crystals. The dynamic mechanical α, β, and γ relaxations of the blends display an intermediate behavior that indicates miscibility in both the crystalline and amorphous phases. In the LDPE/HDPE blend, the melting or crystallization peaks of LDPE were strongly influenced by HDPE. The behavior of the α relaxation was dominated by HDPE, while those of β and γ relaxations were intermediate of the constituents, which were similar to those of the LLDPE/HDPE blends. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1633–1642, 1997     

Metallocene polyolefins and their blends#

Commercial copolymers of 1‐octene and ethylene: metallocene catalyzed (mLLDPE) and Ziegler‐Natta catalyzed (znLLDPE), a low density polyethylene (LDPE), and high density polyethylene (HDPE), were characterized with respect to branching, crystallization behaviour and dynamic‐mechanical properties. It was found that the crystallinity of the polymers is more influenced by the homogeneity of the short‐chain branching than by its content. The study of blends of mLLDPE and znLLDPE with LDPE and HDPE showed that the interaction between mLLDPE and LDPE is stronger than between znLLDPE and LDPE. Blends containing mLLDPE showed a composition depending improvement of the storage modulus G' which was not observed in znLLDPE/LDPE blends. The HPDE blends followed a linear mixing rule. Co‐crystallization was found mLLDPE/LDPE and partially in znLLDPE/LDPE and znLLDPE/HDPE blends, respectively.     

Effect of compatibilizer on morphology and properties of HDPE/Nylon 6 blends

The compatibilization effect of linear low‐density polyethylene‐grafted maleic anhydride (LLDPEgMA) and high‐density polyethylene‐grafted maleic anhydride (HDPEgMA) on high‐density polyethylene (HDPE)/polyamide 6 (Nylon 6) blend system is investigated. The morphology of 45 wt %/55 wt % polyethylene/Nylon 6 blends with three compatibilizer compositions (5 wt %, 10 wt %, and 15 wt %) are characterized by atomic force microscopic (AFM) phase imaging. The blend with 5 wt % LLDPEgMA demonstrates a Nylon 6 continuous, HDPE dispersed morphology. Increased amount of LLDPEgMA leads to sharp transition in morphology to HDPE continuous, Nylon 6 dispersed morphology. Whereas, increasing HDPEgMA concentration in the same blends results in gradual morphology transition from Nylon 6 continuous to co‐continuous morphology. The mechanical properties, oxygen permeability, and water vapor permeability are measured on the blends which confirm the morphology and indicate that HDPEgMA is a better compatibilizer than LLDPEgMA for the HDPE/Nylon 6 blend system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 281–290     

Phase morphology, crystallisation behaviour and mechanical properties of isotactic polypropylene/high density polyethylene blends

The phase morphology, crystallisation behaviour and mechanical properties of isotactic polypropylene (iPP)/high density polyethylene (HDPE) blends were investigated. It was found that the properties are intimately related to each other. The morphology of the blends showed a two phase structure in which the minor phase was dispersed as domains in the major continuous matrix phase. The domain size of the dispersed phase increased with increasing concentration of that phase due to coalescence. It was also found that the domain size of the dispersed phase depends on the viscosity difference between the two phases. For a given HDPE/iPP blend, where HDPE is the matrix and iPP is the dispersed phase, the iPP domains were smaller than HDPE domains of the corresponding iPP/HDPE blend where iPP is the matrix and HDPE is the dispersed phase. A co-continuous morphology was observed at 50/50 PP/HDPE composition. Crystallinity studies revealed that blending has not much effect on the crystalline melting point of polypropylene and high density polyethylene. The crystallisation enthalpy and heat of fusion values of HDPE and PP in the blend were decreased as the amount of the other component increased. The variation in percent crystallinity of HDPE and PP in the blend was found to depend on the morphology of the blend. All the mechanical properties except Young's modulus and hardness showed negative deviation from the additivity line. This is due to the incompatibility of these blends.     

Nanomechanical and Chemical Mapping of the Structure and Interfacial Properties in Immiscible Ternary Polymer Systems

It is a challenge to identify each phase in a multi-component polymer system and uniquely determine the interfacial properties between the different phases. Using atomic force microscopy nanomechanical mapping(AFM-NM) and AFM-based infrared spectroscopy(AFMIR), we identify each phase, visualize structural developments, and determine the interfacial properties in a blend of three polymers: high-density polyethylene(HDPE), polyamide(PA6) and poly(styrene-b-ethylene-co-butylene-b-styrene)(SEBS). Each phase can be identified from the Young's modulus, along with the structural development within the phases before and after compatibilization. The interfacial widths between HDPE/PA6,HDPE/SEBS and SEBS/PA6 were determined independently in one measurement from a Young's modulus map. The structural, mechanical property development and identity of the phases were determined by AFM-NM, while AFM-IR, providing complementary chemical information,identified interfacial reactions, showed the chemical affinity of a compatibilizer with the component phases, and mapped the distribution of the compatibilizer in the ternary polymer blends. The chemical, structural and interfacial information obtained by these measurements provide information that is essential for producing mechanically robust materials from incompatible mixtures of polymers.     

CRYSTALLIZATION AND MECHANICAL PROPERTIES OF BLENDS OF METALLOCENE SHORT CHAIN BRANCHED POLYETHYLENE WITH CONVENTIONAL POLYOLEFINS

Metallocene-catalyzed short chain branched polyethylene (SCBPE) was blended with LDPE, HDPE, PS, EPDM and iPP in the weight proportions of 80 and 20. The crystallization and mechanical properties of these blends were studied by PLM, DSC and DMA. It has been observed in PLM that SCBPE/LDPE, SCBPE/HDPE and SCBPE/EPDM can form band spherulites whose band width and size are both smaller than that of the pure SCBPE. Tiny crystallites are observed in the completely immiscible SCBPE/PS blend. The crystallites in SCBPE/iPP are very small and only irregular spherulites are seen. The crystallization kinetics and mechanical properties of SCBPE are greatly affected by the second polyolefin, but in a different way, depending on the phase behavior and the modulus of the second components. SCBPE may be phase miscible in the melt with HDPE, LDPE and EPDM and co-crystallize together with HDPE or LDPE during cooling. A big change of crystal morphology and crystallization kinetics is seen in SCBPE/iPP blend compared with pure SCBPE and the lowest tanδ is also seen for this system. DMA results show that the tensile modulus of the blends has nothing to do with phase behavior, but only depends on the modulus of the second component.     

Phase morphology development in PP/PA6 blends induced by a maleated thermoplastic elastomer

The effects of maleated thermoplastic elastomer (TPEg) on morphological development of polypropylene (PP)/polyamide 6 (PA6) blends with a fixed PA6 content (30 wt %) were investigated. For purpose of comparison, nonmaleated thermoplastic elastomer (TPE) was also added to the above binary blends. A comparative study of FTIR spectroscopy in above both ternary blends confirmed the formation of in situ graft copolymer in the PP/PA6/TPEg blend. Dynamic mechanical analysis (DMA) indicated that un‐like TPE, the incorporation of TPEg remarkably affected both intensity and position of loss peaks of blend components. Scanning electron microscopy (SEM) demonstrated that PP/PA6/TPE blends still exhibited poor interfacial adhesion between the dispersed phase and matrix. However, the use of TPEg induced a finer dispersion and promoted interfacial adhesion. Transmission electron microscopy (TEM) for PP/PA6/TPEg blends showed that a core‐shell structure consisting of PA6 particles encapsulated by an interlayer was formed in PP matrix. With the concentration of TPEg increasing, the dispersed core‐shell particles morphology was found to transform from discrete acorn‐type particles to agglomerate with increasing degree of encapsulation. The modified Harkin's equation was applied to illustrate the evolution of morphology with TPEg concentration. “Droplet‐sandwiched experiments” further confirmed the encapsulation morphology in PP/PA6/TPEg blends. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1050–1061, 2006     

Friction and wear mechanisms of polyamide 66/high density polyethylene blends

Polyamide 66 (PA66)/high density polyethylene (HDPE) blends having miscible structure were produced by compatibilization of HDPE grafted with maleic anhydride (HDPE‐g‐MAH). Mechanical and tribological properties of blends in different compositions were tested. It was found that the polymer blends greatly improved the mechanical properties of PA66 and HDPE. Blending HDPE with PA66 significantly decreased the friction coefficient of PA66; the friction coefficients of blends with different compositions were almost the same and approximately equal to that of pure HDPE; the blends with 80 vol % PA66 exhibited the best wear resistance. The transfer films, counterpart surfaces, and wear debris formed during sliding were investigated by Scanning Electron Microscopy (SEM), and Differential Scanning Calorimetry (DSC) analysis was further carried out on wear debris. These investigations indicated that the thermal control of friction model is applicable to PA66/HDPE blend, that is the friction coefficient of blend is governed by the HDPE component, which possesses a lower softening point relative to the PA66 component in this system. The wear mechanism of PA66/HDPE blend transforms from PA66 to HDPE as the HDPE content increases. PA66, as the component with higher softening point, increases the hardness of blend, enhances the ability of blend to form a transfer film on the counterface, and inhibits the formation of larger belt‐like debris of HDPE, at the same time, the presence of self‐lubricating HDPE in the system decreases the friction coefficient and the frictional heat, all of these factors are favorable for the wear resistance of PA66/HDPE blend. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2514–2523, 2005     

Barrier,Mechanical, Morphological and Thermal Properties of Compatibilized High Density Polyethylene and Polyamide 6 Blends

Effectiveness of the content of maleic anhydride (MAH) and polyamide 6 (PA6) on mechanical, thermal, barrier (moisture and oxygen) properties of HDPE/PA6 blends was investigated. Blends of HDPE with PA6 were prepared by in situ method. Molau test and FTIR spectroscopy results confirmed the reactive compatibilization through grafting of MAH on HDPE and PA6 chains in PA6/HDPE blends. Low concentration of benzoyl peroxide (BPO) and MAH reduced the particle size, improved phase morphology and mechanical properties of PA6/HDPE blends. Decrease in mechanical properties of PA6/HDPE blends was observed at high concentration of BPO and MAH.     

Largely enhanced ductility of immiscible high density polyethylene/polyamide 6 blends via nano‐bridge effect of functionalized multiwalled carbon nanotubes

Immiscible polymer blends usually exhibit negative deviation in mechanical properties compared with the corresponding pure polymers due to the weak interfacial bonding between the two polymers. Due to the bridge effect of the oriented carbon nanotubes (CNTs) on the craze and crack development at the load of stress, CNTs have been proved to be efficient toughening agent for polymers. In this work, functionalized multiwalled carbon nanotubes (FMWCNTs) have been introduced into immiscible high density polyethylene/polyamide 6 (HDPE/PA6) blends through different sample preparation methods. The mechanical measurements demonstrate that, when the nanocomposite is prepared from the HDPE master batch, the sample exhibits excellent tensile strength and toughness simultaneously. For all the nanocomposites, FMWCNTs tend to migrate and/or maintain in PA6 particles, leading to the variation of the crystallization behavior in PA6 phase. Further results based on morphologies characterization indicate that the intensified interfacial adhesion between HDPE and PA6, which is realized by the nano‐bridge effect of FMWCNTs in the interfaces, is the main reason for the largely improved ductility. Copyright © 2010 John Wiley & Sons, Ltd.     

A study on melt grafting of maleic anhydride onto low‐density polyethylene and its blend with polyamide 6

Graft copolymerization of low‐density polyethylene (LDPE) with a maleic anhydride (MAH) was performed using intermeshing corotating twin‐screw extruder in the presence of benzoyl peroxide (BPO). The LDPE/polyamide 6 (PA6) and LDPE‐g‐MAH/PA6 blends were prepared in a corotating twin‐screw extruder. The melt viscosity of the grafted LDPE was measured by a capillary rheometer. The grafted copolymer was characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microcopy (SEM). The influence of the variation in temperature, BPO and MAH concentration, and temperature on the grafting degree and on the melt viscosity was studied. The grafting degree increased appreciably up to about 0.45 phr and then decreased continuously with an increasing BPO concentration. According to the FTIR analysis, it was found that the amount of grafted MAH on the LDPE chains was ～5.1%. Thermal analysis showed that melting temperature of the graft copolymers decreases with increasing grafting degree. In addition to this, loss modulus (E″) of the copolymers first increased little with increasing grafting and then obviously decreased with increasing grafting degree. Furthermore, the results revealed that the tensile strength of the blends increased linearly with increasing PA6 content. The results of SEM and mechanical test showed that the blends have good interfacial adhesion and good stability of the phase structure, which is reflected in the mechanical properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 267–275, 2010     

Reactive compatibilization of polyolefin/PET blends by melt grafting with glycidyl methacrylate

The melt free radical grafting of glycidyl methacrylate (GMA) onto high‐density polyethylene (HDPE) was carried out in Brabender internal mixer. The GMA content of the grafted HDPE (HDPE‐g‐GMA) was determined through FTIR by means of a calibration curve. The influence of reaction procedure, radical initiator concentration and addition of a co‐monomer (styrene) on the grafting efficiency was examined. Blends of poly(ethylene terephthalate) (PET) with HDPE and HDPE‐g‐GMA (75/25 w/w) were prepared by melt mixing in internal mixer. The morphology of the blends was then analysed by SEM microscopy. PET/HDPE‐g‐GMA blends displayed improved phase dispersion and interfacial adhesion as compared to unfanctionalized PET/HDPE blend.     

Thermomechanical study of low-density polyethylene, polyamide 6 and its blends

By using thermomechanical analysis (TMA) multiple relaxation transitions in the amorphous part of semi-crystalline polymers and their blends can be found. These result from differences in the interaction energies between segments of macromolecules, and as a result, in molecular mobility. TMA shows essential changes in the structure of low-density polyethylene (LDPE) resulting from the grafting of a maleic anhydride (LDPE-g-MAH) onto this semi-crystalline polymer. The grafting process did not suppress the ability of polyethylene to crystallize. Essential changes were found in molecular weight distribution and relaxation transitions of the ternary blends LDPE/PA6 (polyamide 6, PA6)/LDPE-g-MAH studied. For a concentration of PA6 up to 30 wt.%, a single relaxation transition is visible, which testifies that the components are miscible in the amorphous region. For blends with 40 and 50 wt.% of PA6, this structure was transformed and two relaxation transitions are visible. From the results obtained in this study it is concluded that the introduction 5 wt.% of grafted polyethylene is sufficient to produce a PA6/LDPE blend only for PA6 concentration up to 30 wt.% which is homogenous on “molecular” level. The transformation of the structure of the ternary polymer blend was explained by the interaction of the components during the melt mixing and changes in the structure of its amorphous regions.     

Effects of reprocessing on polymers—Part III: Photo-oxidation of polyethylene-polypropylene blends

It is shown that blends of low density polyethylene (LDPE) and polypropylene (PP) photo-oxidise more readily than LDPE alone and there was evidence of cross-linking between the two phases. An ethylene-propylene rubber (EPDM) which improved the mechanical performance of LDPE/PP blends caused an increase in the rate of photo-degradation as measured by carbonyl formation and by loss of toughness.     

TIME-DEPENDENT MORPHOLOGY OF POLYETHYLENE-POLYPROPYLENE BLENDS

The effect of time-temperature treatment on morphology of polyethylene-polypropylene (PE-PP) blends wasstudied to establish a relationship between thermal history, morphology and mechanical properties. Polypropylene (PP)homopolymers were used to blend with various polyethylenes (PE), including high density polyethylene (HDPE), lowdensity polyethylene (LDPE), linear low density polyethylene (LLDPE), and very and ultra low density polyethylene(VLDPE and ULDPE). The majority of the blends were prepared at a ratio of PE:PP = 80:20, while blends of PP and LLDPEwere prepared at various compositions. Thermal treatment was carried out at temperatures between the crystallizationtemperatures of PP and PEs to allow PP to crystallize first from the blends. On cooling further, PE crystallized too. A verydiffuse PP spherulite morphology in the PE matrix was formed in some partially miscible blends when PP was less than 20%by mass. Droplet-matrix structures were developed in other blends with either PP or PE as dispersed domains in a continuousmatrix, depending on the composition ratio. The scanning electron microscopy (SEM) images displayed a fibrillar structureof PP spherulite in the LLDPE-PP (80:20) and large droplets of PP in the HDPE-PP (80:20) blend, providing larger surfacearea and better bonding in the LLDPE-PP (80:20) blends. This explains why the blends with diffuse spherulite morphologyshowed greater improvement in tensile properties than droplet-matrix morphology blends after time-temperature treatment.     

PA6/HIPS/PP-g-(GMA-co-St)反应共混体系的研究

通过扫描电镜、热分析、熔体流动速率、熔融扭矩和力学性能等测试方法研究了甲基丙烯酸缩水甘油酯(GMA)和苯乙烯(St)多单体熔融接枝聚丙烯[PP-g-(GMA-co-St)]对PA6/HIPS共混物的熔融流变性能、结晶行为、相形态和力学性能的影响.结果表明,在熔融共混过程中,PP-g-(GMA-co-St)中的环氧基与PA6的端氨基原位生成的接枝共聚物有效地降低了共混物的界面张力,提高了共混物的界面粘着力,使共聚物的流动速率降低,熔融扭矩提高;PA6分子链的规整性降低,结晶完善性变差.在PP-g-(GMA-co-St)的质量分数为10%时,共混物分散相的尺寸明显减少,力学性能得到较大提高;其中冲击强度超过纯PA6,达到HIPS水平.通过反应共混,制备了力学性能均衡的PA6/HIPS/PP-g-(GMA-co-St)共混物合金.     

应力引发官能化EPDM/HDPE及其对PA66/EPDM/HDPE 共混物相形态和力学性能的影响

通过提高双螺杆挤出机螺杆转速的方法,研究了熔融挤出过程中高剪切应力对马来酸酐(MAH)官能化三元乙丙橡胶(EPDM)与高密度聚乙烯(HDPE)共混物的接枝率、熔体流动速率及凝胶含量的影响.随着双螺杆挤出机螺杆转速的增加,强烈的机械剪切应力引发EPDM/HDPE共混物大分子链的断链反应形成大分子自由基,从而引发接枝反应制...