Molecular dynamics of amorphous/crystalline polymer blends studied by broadband dielectric spectroscopy

The molecular dynamics of poly(vinyl acetate), PVAc, and poly(hydroxy butyrate), PHB, as an amorphous/crystalline polymer blend has been investigated using broadband dielectric spectroscopy over wide ranges of frequency (10⁻² to 10⁵ Hz), temperature, and blend composition. Two dielectric relaxation processes were detected for pure PHB at high and low frequency ranges at a given constant temperature above the T_g. These two relaxation peaks are related to the α and α′ of the amorphous and rigid amorphous regions in the sample, respectively. The α′-relaxation process was found to be temperature and composition dependent and related to the constrained amorphous region located between adjacent lamellae inside the lamellar stacks. In addition, the α′-relaxation process behaves as a typical glass relaxation process, i.e., originated from the micro-Brownian cooperative reorientation of highly constraints polymeric segments. The α-relaxation process is related to the amorphous regions located between the lamellar crystals stacks. In the PHB/PVAc blends, only one α-relaxation process has been observed for all measured blends located in the temperature ranges between the T_g’s of the pure components. This last finding suggested that the relaxation processes of the two components are coupled together due to the small difference in the T_g’s (ΔT_g = 35 °C) and the favorable thermodynamics interaction between the two polymer components and consequently less dynamic heterogeneity in the blends. The T_g’s of the blends measured by DSC were followed a linear behavior with composition indicating that the two components are miscible over the entire range of composition. The α′-relaxation process was also observed in the blends of rich PHB content up to 30 wt% PHB. The molecular dynamics of α and α′-relaxation processes were found to be greatly influenced by blending, i.e., the dielectric strength, the peak broadness, and the dielectric loss peak maximum were found to be composition dependent. The dielectric measurements also confirmed the slowing down of the crystallization process of PHB in the blends.     

Relationship between morphology and glass transition temperature in solvent-crystallized poly(aryl ether ketones)

The relationship between semicrystalline morphology and glass transition temperature has been investigated for solvent-crystallized poly(ether ether ketone) (PEEK) and poly(ether ketone ketone) (PEKK). Solvent-crystallized specimens of both PEEK and PEKK displayed a sizeable positive offset in T_g compared to quenched amorphous specimens as well as thermally crystallized specimens of comparable bulk crystallinity; the offset in T_g for the crystallized samples reflected the degree of constraint imposed on the amorphous segments by the crystallites. Small-angle X-ray scattering studies revealed markedly smaller crystal long periods (d) for the solvent-crystallized specimens compared to samples prepared by direct cold crystallization. The strong inverse correlation observed between T_g and interlamellar amorphous thickness (l_A) based on a simple two-phase model was in excellent agreement with data reported previously for PEEK, and indicated the existence of a unique relationship between glass transition temperature and morphology in these poly(aryl ether ketones) over a wider range of sample preparation history and lamellar structure than was previously reported. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 65–73, 1998     

Vitrification/devitrification phenomena during isothermal and nonisothermal crystallization of poly(aryl–ether–ether–ketone) (PEEK) and PEEK/poly(ether–imide) blends

We have established time–temperature transformation and continuous-heating transformation diagrams for poly(ether–ether–ketone) (PEEK) and PEEK/poly(ether–imide) (PEI) blends, in order to analyze the effects of relaxation control on crystallization. Similar diagrams are widely used in the field of thermosetting resins. Upon crystallization, the glass transition temperature (T_g) of PEEK and PEEK/PEI blends is found to increase significantly. In the case of PEEK, the shift of the α-relaxation is due to the progressive constraining of amorphous regions by nearby crystals. This phenomenon results in the isothermal vitrification of PEEK during its latest crystallization stages for crystallization temperatures near the initial T_g of PEEK. However, vitrification/devitrification effects are found to be of minor importance for anisothermal crystallization, above 0.1°C/min heating rate. In the case of PEEK/PEI blends, amorphous regions are progressively enriched in PEI upon PEEK crystallization. This promotes a shift of the α-relaxation of these regions to higher temperatures, with a consequent vitrification of the material when crystallized below the T_g of PEI. The data obtained for the blends in anisothermal regimes allow one to detect a region in the (temperature/heating rate) plane where crystallization proceeds in the continuously close proximity of the glass transition (dynamic vitrification). These experimental findings are in agreement with simple simulations based on a modified Avrami model coupled with the Fox equation. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 919–930, 1998     

Reorganization of the structures,morphologies, and conformations of bulk polymers via coalescence from polymer–cyclodextrin inclusion compounds

Bulk poly(ethylene terephthalate) (PET) and bisphenol A polycarbonate (PC) samples have been produced by the coalescence of their segregated, extended chains from the narrow channels of the crystalline inclusion compounds (ICs) formed between the γ‐cyclodextrin (CD) host and PET and PC guests, which are reported for the first time. Differential scanning calorimetry, Fourier transform infrared, and X‐ray observations of PET and PC samples coalesced from their crystalline γ‐CD‐ICs suggest structures and morphologies that are different from those of samples obtained by ordinary solution and melt processing techniques. For example, as‐received PC is generally amorphous with a glass‐transition temperature (T_g) of about 150 °C; when cast from tetrahydrofuran solutions, PC is semicrystalline with a melting temperature (T_m) of about 230 °C; and after PC/γ‐CD‐IC is washed with hot water for the removal of the host γ‐CD and for the coalescence of the guest PC chains, it is semicrystalline but has an elevated T_m value of about 245 °C. PC crystals formed upon the coalescence of highly extended and segregated PC chains from the narrow channels in the γ‐CD host lattice are possibly more chain‐extended and certainly more stable than chain‐folded PC crystals grown from solution. Melting the PC crystals formed by coalescence from PC/γ‐CD‐IC produces a normal amorphous PC melt that, upon cooling, results in typical glassy PC. PET coalesced from its γ‐CD‐IC crystals, although also semicrystalline, displays a T_m value only marginally elevated from that of typical bulk or solution‐crystallized PET samples. However, after the melting of γ‐CD‐IC‐coalesced PET crystals, it is difficult to quench the resultant PET melt into the usual amorphous PET glass, characterized by a T_g value of about 80 °C. Instead, the coalesced PET melt rapidly recrystallizes during the attempted quench, and so upon reheating, it displays neither a T_g nor a crystallization exotherm but simply remelts at the as‐coalesced T_m. This behavior is unaffected by the coalesced PET sample being held above T_m for 2 h, indicating that the extended, unentangled nature of the chains in the noncrystalline regions of the coalesced PET are not easily converted into the completely disordered, randomly coiled, entangled melt. Apparently, the highly extended, unentangled characters of the PC and PET chains in their γ‐CD‐ICs are at least partially retained after they are coalesced. Initial differential scanning calorimetry, thermogravimetric analysis, Fourier transform infrared, and X‐ray observations are described here. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 992–1012, 2002     

On the predictability of the high-frequency elastic modulus of semicrystalline polymers as function of crystallinity

The relation of the high-frequency elastic moduli of semicrystalline polymers to volume fraction crystallinity is correctly described by the Hashin-Shtrikman theory, without any disposable constants, as a function of the ratio of the modulus of the amorphous to that of the crystalline phase. Hence the (high-frequency) reduced modulus of semicrystalline polymers is largely a function of the temperature T/T_g. The importance of T/T_m for the modulus of the crystalline phase precludes the existence of a single universal reduced modulus versus temperature curve.     

New insights into the multiple melting behaviors of the semicrystalline ethylene‐hexene copolymer: Origins of quintuple melting peaks

A semicrystalline ethylene‐hexene copolymer (PEH) was subjected to a simple thermal treatment procedure as follows: the sample was isothermally crystallized at a certain isothermal crystallization temperature from melt, and then was quenched in liquid nitrogen. Quintuple melting peaks could be observed in heating scan of the sample by using differential scanning calorimeter (DSC). Particularly, an intriguing endothermic peak (termed as Peak 0) was found to locate at about 45 °C. The multiple melting behaviors for this semicrystalline ethylene‐hexene copolymer were investigated in details by using DSC. Wide‐angle X‐ray diffraction (WAXD) technique was applied to examine the crystal forms to provide complementary information for interpreting the multiple melting behaviors. Convincing results indicated that Peak 0 was due to the melting of crystals formed at room temperature from the much highly branched ethylene sequences. Direct heating scans from isothermal crystallization temperature (T_c, 104–118 °C) were examined for comparison, which indicated that the multiple melting behaviors depended on isothermal crystallization temperature and time. A triple melting behavior could be observed after a relatively short isothermal crystallization time at a low T_c (104–112 °C), which could be attributed to a combination of melting of two coexistent lamellar stack populations with different lamellar thicknesses and the melting‐recrystallization‐remelting (mrr) event. A dual melting behavior could be observed for isothermal crystallization with both a long enough time at a low T_c and a short or long time at an intermediate T_c (114 °C), which was ascribed to two different crystal populations. At a high T_c (116–118 °C), crystallizable ethylene sequences were so few that only one single broad melting peak could be observed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2100–2115, 2008     

Elevation of the glass transition temperature in flexible‐chain semicrystalline polymers

In the idealized two‐phase model of a semicrystalline polymer, the amorphous intercrystalline layers are considered to have the same properties as the fully‐amorphous polymer. In reality, these thin intercrystalline layers can be substantially influenced by the presence of the crystals, as individual polymer molecules traverse both crystalline and amorphous phases. In polymers with rigid backbone units, such as poly(etheretherketone), PEEK, previous work has shown this coupling to be particularly severe; the glass transition temperature (T_g) can be elevated by tens of degrees celsius, with the magnitude of the elevation correlating directly with the thinness of the amorphous layer. However, this connection has not been explored for flexible‐chain polymers, such as those formed from vinyl‐type monomers. Here, we examine T_g in both isotactic polystyrene (iPS) and syndiotactic polystyrene (sPS), crystallized under conditions that produce a range of amorphous layer thicknesses. T_g is indeed shown to be elevated relative to fully‐amorphous iPS and sPS, by an amount that correlates with the thinness of the amorphous layer; the magnitude of the effect is severalfold less than that in PEEK, consistent with the minimum lengths of polymer chain required to make a fold in the different cases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1198–1204, 2007     

A study of the blending of ethylene–styrene copolymers differing in the copolymer styrene content: Miscibility considerations

Blends of two or more ethylene–styrene (ES) copolymers that differed primarily in the comonomer composition of the copolymers were studied. Available thermodynamic models for copolymer–copolymer blends were utilized to determine the criteria for miscibility between two ES copolymers differing in styrene content and also between ES copolymers and the respective homopolymers, polystyrene and linear polyethylene. Model estimations were compared with experimental observations based primarily on melt‐blended ES/ES systems, particularly via the analysis of the glass‐transition (T_g ) behavior from differential scanning calorimetry (DSC) and solid‐state dynamic mechanical spectroscopy. The critical comonomer difference in the styrene content at which phase separation occurred was estimated to be about 10 wt % for ES copolymers with a molecular weight of about 10⁵ and was in general agreement with the experimental observations. The range of ES copolymers that could be produced by the variation of the comonomer content allowed the study of blends with amorphous and semicrystalline components. Crystallinity differences for the blends, as determined by DSC, appeared to be related to the overlapping of the T_g of the amorphous component with the melting range of the semicrystalline component and/or the reduction in the mobility of the amorphous phase due to the presence of the higher T_g of the amorphous blend component. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2976–2987, 2000     

Solid-state coextrusion of poly(ethylene terephthalate). II. Drawing of semicrystalline PET

The drawing of semicrystalline (33 and 50%) poly(ethylene terephthalate) (PET) films has been studied by solid-state coextrusion. Because of its brittleness and opacity, isotropic and semicrystalline PET film is of little practical use. Early attempts to cold-draw crystalline films led to fracture in contrast to deformation of amorphous PET. However, we have succeeded in systematically preparing films with extrusion draw ratios ≤4.4 from semicrystalline PET. In many cases, the properties of the drawn extrudates, as a function of extrusion temperature T_ext and extrusion draw ratio EDR, were similar to those prepared from amorphous PET. However, some remarkable differences have also been found. In the case of coextrudates prepared from isotropic 50% crystalline PET, we found that the larger the deformation, the lower the apparent resulting crystallinity. In the extreme, a 34% reduction in crystallinity after deformation was observed. For the coextrudates drawn from initially 33% crystalline PET, slightly different behavior occurred. For T_ext ≤ 90°C, all extrudates showed crystallinities lower than the original isotropic film, with a minimum at EDR = 3; for T_ext ≥ 110°C, crystallinities were slightly greater than in the original film and increased with EDR. Qualitative measurements of heats of fusion were in agreement with density gradient results for PET crystallinity. In contrast is our previous finding that extrudates from initially amorphous PET always increase in crystallinity with EDR, because of stress-induced crystallization. The results now suggest that in the T_ext range investigated, the initial spherulitic structure is at least in part destroyed on drawing. In addition, the percent crystallinity is revealed to be dependent on T_ext, with lower values at lower temperatures. Mechanical tests show that the extrudates are similar or sometimes higher in tensile modulus when compared to amorphous PET drawn under the same conditions.     

Effect of morphology on the dynamic mechanical properties of a semicrystalline polysiloxane

The dynamic mechanical properties of semicrystalline poly(tetramethyl-p-silphenylene siloxane) in three morphological preparations were measured over the wide frequency range of about 0.002 Hz to 500 Hz and the temperature range of about ? 190°C to 100°C. The three samples were all isothermally crystallized at 125°C. Two samples had a spherulite size of 25 μ diameter but differed in the time allowed for secondary crystallization. The other sample had a smaller spherulite size. By assuming compliance additivity, the viscoelastic behavior could be separated into five relaxation processes with an indication that a sixth existed at low temperature. Two processes called γ₁ and γ₂ could be resolved at low temperatures. The γ₁ process was associated with the amorphous region since the peak strength was affected by the rate of cooling through the glass transition region; the γ₂ peak, unaffected by cooling rate, is attributed to the crystalline part. In the high-temperature region, the β peak is associated with the glass transition and has a shape and location that is essentially independent of the morphology. The highest temperature α₂ process, whose maximum was not observed in the experimental range covered, is attributed to the crystalline region and is sensitive to changes in crystallization history. The strength of the α₁ process unlike that of the other processes was found to be a function of temperature; it was associated with the noncrystalline region.     

The “Relaxed” state in a semicrystalline polymer: Experimental characterization and modeling

This work addresses the general issue of the mechanical behavior of the confined amorphous phase in rubbery semicrystalline polymers. Even far above the glassy transition temperature, the amorphous phase in semicrystalline polymers is known to remain constrained by crystals and is less mobile than a purely amorphous polymer close to its equilibrium rubbery state. The aim of this paper, based on Polyamide 11, is to investigate the existence and significance of a relaxed state in the amorphous phase of a semicrystalline polymer far above T _g. A strain-rate independent tensile curve (called the “asymptotic curve”) is evidenced below a critical strainrate, consistently with a fully relaxed state of the rubbery amorphous phase. Nevertheless, a contradictory mechanical phenomenology was observed at the same time (hysteretic unloading, relaxation, and creep involving the same strain-rates as the “asymptotic” loading regime), suggesting joint amorphous and crystalline processes. Modeling of this paradoxical behavior is attempted, based on the experimental results. The first one-dimensional simulations are presented. Published in Russian in Vysokomolekulyarnye Soedineniya, Ser. A, 2008, Vol. 50, No. 5, pp. 797–808. This article was submitted by the authors in English.     

Evidence of dynamic heterogeneity as obtained from dielectric and brillouin light-scattering studies of poly(n-hexylmethacrylate)

We report dielectric relaxation and Rayleigh-Brillouin spectroscopic measurements on the side chain polymer poly(n-hexylmethacrylate), PHMA (T_g = 268 K), exhibiting a broad glass transition region. The dielectric loss curves can be represented by single Havriliak-Negami functions in the temperature range of 260–450 K. The width of the distribution relaxation function is a decreasing function of temperature up to T = 333 K ≊ 1.24 × T_g and remains virtually constant above that temperature. This is interpreted as marking the merging of the α-process with a slow β-relaxation in agreement with the value of the cooperativity length associated with the α-mode. Hence above that temperature, the relaxation times confirm well to an Arrhenius temperature dependence. The hypersonic dispersion deduced from the Brillouin spectra (210–550 K) surprisingly peaks at temperatures near T_g which bears no relation to the main α-relaxation. This structural relaxation is rather associated with the side hexyl group motion showing striking resemblance with the hypersonic dispersion in molecular liquids. It is conceivable that the observed damping in PHMA is dynamically related to the internal plasticization effect of the hexyl group. © 1996 John Wiley & Sons, Inc.     

Dielectric relaxation of poly(phenylene sulfide) containing a fraction of rigid amorphous phase

The dielectric relaxation behavior of poly(phenylene sulfide), PPS, has been investigated from room temperature to 180°C. This study was undertaken to examine the mobility of the amorphous phase through the glass transition region, to determine the contribution that rigid amorphous phase material makes to the relaxation process. Semicrystalline samples contain a fraction of the rigid amorphous phase, which was determined from the heat capacity increment at the glass transition, using degree of crystallinity determined from x-ray scattering. In the dielectric experiment, we measured the temperature and frequency dependence of the real and imaginary parts of the dielectric function. ε″ vs. ε′ was used to determine the dielectric relaxation intensity, δε = ε_s–ε∞, at temperatures above the glass transition. For amorphous PPS, δε decreases as temperature increases, while for all semicrystalline PPS, δε increases with temperature. The ratio of semicrystalline intensity to amorphous intensity determines the total fraction of dipoles which are already relaxed at a given temperature. Results indicate that more and more rigid amorphous phase material relaxes as the temperature is increased. This provides the first evidence that rigid amorphous phase material in PPS contains chains that possess different levels of molecular mobility. Finally, to the temperature of the loss peak maximum, at a given frequency, we assign the value of the dielectric T_g. For both melt and cold crystallization, the dielectric T_g systematically decreases as the crystallization temperature increases, and as the fraction of rigid amorphous phase decreases.     

Poly(propylene isophthalate), poly(propylene succinate), and their random copolymers: Synthesis and thermal properties

Poly(propylene isophthalate) (PPI), poly(propylene succinate) (PPS), and poly(propylene isophthalate/succinate) (PPI‐PPS) random copolymers were synthesized and characterized in terms of chemical structure and molecular weight. The thermal behavior was examined by TGA and DSC. All the polymers showed a good thermal stability. At room temperature, they appeared as semicrystalline materials, except 20PPI‐PPS and 30PPI‐PPS: the main effect of copolymerization was a lowering in the amount of crystallinity and a decrease of T_m with respect to homopolymers. A crystalline phase of PPI and PPS was evidenced at high content of PI or PS units, respectively. Amorphous samples were obtained after melt quenching and an increment of T_g, with the increment of PI units, was observed. This behavior was explained as due to the presence of stiff phenylene groups. The Wood equation described well T_g‐composition data. Lastly, the presence of a rigid‐amorphous phase was evidenced in copolymers, differently from the two homopolymers. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 310–321, 2007.     

Influence of aging and crystallinity on the molecular motions in bisphenol-A polycarbonate

Thermally Stimulated Depolarization Current technique, Differential Scanning Calorimetry, and Dynamic Mechanical Analysis have been applied to amorphous and semicrystalline bisphenol-A polycarbonate with crystallinity degrees up to 21.8%, in a temperature interval covering the α and β relaxations. The secondary β transition is found to be the sum of three components whose variations in aged and annealed specimens have shown the cooperative character of the β₁ and β₂ modes, contrary to the localized nature of the β₃ component. A T_g decrease was observed by both TSDC and DSC as a function of X_c and has been related to the possible confinement of the mobile amorphous phase in regions whose sizes are smaller than the correlation lengths of the cooperative movements that characterize the motions occurring at T_g. The α relaxation intensity variations with crystallinity show the existence of an abundant rigid amorphous phase in the semicrystalline material. The relaxation parameters deduced from the Direct Signal Analysis of the α relaxation for the mobile amorphous phase do not show significant deviations from those found for the amorphous material. The existence of the rigid amorphous phase has been associated to the ductile-to-brittle transition experienced by the material at low crystallinity levels. © 1996 John Wiley & Sons, Inc.     

Morphology and modulus–temperature behavior of semicrystalline poly(ethylene terephthalate) (PET)

The influence of the thermal history on the morphology and mechanical behavior of PET was studied. The degree of crystallinity (density measurements) and the morphological structure (electron microscopy and small-angle x-ray diffraction) depend on the crystallization temperature. The viscoelastic parameters obtained from the modulus–temperature curves are mainly determined by the morphology of the samples. The glass-transition temperature, T_i, is a function of the crystallinity and the crystallization temperature. It is maximum for a crystallinity between 0.34 and 0.39 for a sample crystallized isothermally between 120 and 150°C. This dependence on crystallization conditions is ascribed to the conformation of the amorphous chain segments between the crystalline lamellae as well as the concentration and the molecular weight of the polymer material rejected during isothermal crystallization. Both factors are supposed to be temperature-dependent. The value of the rubbery modulus is a function of both the volume concentration of the crystalline lamellae and the structure of the interlamellar amorphous regions (chain folds, tie molecules, chain ends, and segregated low molecular weight material). Annealing above the crystallization temperature of isothermally crystallized samples has a marked influence on their morphology and mechanical behavior. The morphological structure and the viscoelastic properties of annealed PET samples are completely different from those obtained with samples isothermally crystallized at the same temperature.     

Miscible blends prepared from two crystalline polymers

Differential scanning calorimetry was used to determine the miscibility behavior of several polyester/Saran blends, the two polymers forming these blends being semicrystalline. It was found that Saran is miscible with polycaprolactone (PCL), polyvalerolactone, poly(butylene adipate), and poly(hexamethylene sebacate) since a single glass transition temperature T_g was observed at each composition. However, immiscibility was found between Saran and poly(ethylene adipate), poly-(ethylene succinate), poly(β-propiolactone), and poly(α-methyl-α-n-propyl-β-propiolactone) since two T_g's were recorded at several compositions. Blends were then obtained containing, over a wide range of composition, a miscible amorphous phase and two different types of crystals. From melting-point depression data on PCL and Saran crystals, thermodynamic interaction parameters χ were calculated and found to be different for PCL-rich blends and for Saran-rich blends. This result suggests a variation of χ with composition. Saran is a polymer which does not contain α-hydrogens and its miscibility with polyesters may result from a β-hydrogen bonding interaction or a C?O/C? Cl dipole-dipole interaction.     

Dielectric relaxation spectroscopy of amorphous and liquid-crystalline side-chain polycarbonates

The molecular dynamics of amorphous and liquid-crystalline (LC) side-chain polycarbonates was studied by dielectric spectroscopy at frequencies from 10⁻² to 10⁶ Hz and at temperatures from −160 to 180°C. ‘Model’ compounds containing no mesogenic side-groups showed two relaxations, which originate from the carbonate group (α, β_m-relaxation). By contrast, in LC-polycarbonates bearing a mesogenic nitrostilbene side group around and above the glass transition temperature T_g up to three relaxation modes were distinguished (α-, λ₁-, λ₂-process); below T_g four secondary relaxations (γ-, β_m-, β_s-, β_sc-relaxation) were observed. The γ-relaxation was found only in compounds possessing an aliphatic spacer linked to the backbone by an ether bond. Apart from β_m-, two additional β-processes were identified as relaxations associated with the mesogenic unit in the glassy (β_s) or in the crystalline state (β_sc).     

Unique morphological and thermal behaviors of reorganized poly(ethylene terephthalates)

Bulk poly(ethylene terephthalate) PET has been reorganized both morphologically and conformationally by processing from its inclusion complex (IC) formed with γ‐cyclodextrin (CD). In the narrow channels of its γ‐CD‐IC crystals the included guest PET chains are isolated from neighboring PET chains and the ethylene glycol (EG) units adopt the highly extended g±tg? kink conformations, whose cross‐sectional diameters are ～80% of the diameter of the fully extended, all‐trans crystalline PET conformer, though they are nearly (～95%) as extended. When the highly extended, unentangled guest PET chains are coalesced from their γ‐CD‐IC crystals by exposure to hot water, host γ‐CDs are removed and the PET chains are presumably consolidated into a bulk sample with a morphology and constituent chain conformations not normally found in PET samples solidified from their randomly coiling, possibly entangled, disordered melts and solutions. Observations by polarized light and atomic force microscopies provide visual evidence for widely different semicrystalline morphologies developed in coalesced and as‐received PETs when crystallized from their melts, with possibly chain extended, small crystals and spherulitic, chain‐folded, large crystals, respectively. DSC observations reveal that coalesced PET is rapidly crystallizable from the melt, while as‐received PET is slow to crystallize and is easily quenched into a totally amorphous sample. Analyses of ¹³C‐NMR data strongly indicate that the PET chains in the noncrystalline regions of the coalesced sample remain predominantly in the highly extended kink conformations, with g±tg? EG units, which are required by their inclusion into PET‐γ‐CD‐IC crystals, while the predominantly amorphous PET chains in the as‐received sample have high concentrations of gauche± ? CH₂? CH₂? and trans ? O? CH₂? ,? CH₂? O? EG bond conformations. ¹³C‐NMR T₁(¹³C) and T_1ρ(¹H) relaxation studies show no evidence of a glass transition for coalesced PET, while the as‐received sample shows abrupt changes in both the MHz [T₁(¹³C)] and kHz [T_1ρ(¹H)] motions at T ～ T_g. Preliminary observations of differences in their macroscopic properties are attributed to the very different morphologies and conformations of the constituent chains in these PET samples. Apparently the kink conformers in the noncrystalline regions of coalesced PET are at least partially retained for extended periods even in the melt and are rapidly crystallized upon cooling. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 386–394, 2004     

Local chain motions of poly(β-hydroxyoctanoate) in the bulk. 13C NMR relaxation study

Variable-temperature ¹³C NMR spin-lattice relaxation times (T₁) and Nuclear Overhauser Enhancements (NOE) at two magnetic fields have been used to study the dynamics of the amorphous part of a semicrystalline sample (33% of crystallinity) of poly(β-hydroxyoctanoate) (PHO). The interpretation of the relaxation data of the backbone carbons was made by employing a number of motional models. Among these, the DLM model offered the best interpretation of the relaxation data in terms of conformational transitions and librational motions of the backbone C? H vectors, and proved to be superior to unimodal distribution functions. The interpretation of temperature- and frequency-dependent T₁ and NOE data of the carbon nuclei in the n-pentyl side chain was made by employing a newly developed composite spectral density function for multiple internal C? C bond rotations of restricted amplitude and chain segmental motion. The temperature dependence of the linewidths of the various protonated carbon resonances of PHO has been discussed in terms of the semicrystalline character of this polymer. © 1995 John Wiley & Sons, Inc.