Highly phenylated poly(aryl ether phthalazine)s

Two series of novel amorphous poly(aryl ether phthalazine)s have been prepared via an intramolecular ring closure reaction of poly(aryl ether ketone)s (PAEKs) with hydrazine monohydrate. Fluorinated PAEKs, which display solubility in solvents incorporating a ketone functionality such as acetone or ethyl acetate, were converted to poly(aryl ether phthalazine)s to observe if these polymers would display similar solubility characteristics. The poly(aryl ether phthalazine)s have glass transition temperatures in the range of 278–320°C and show 5% weight loss points greater than 500°C in air and nitrogen atmospheres. The fluorinated poly(aryl ether phthalazine)s were not soluble in ketonic solvents. A series of poly(aryl ether phthalazine)s incorporating pendant 2-naphthalenyl moieties has been prepared in an attempt to produce amorphous, thermally stable polymers with high glass transition temperatures. The polymers have glass transition temperatures in the range of 287–334°C and show 5% weight loss points greater than 500°C in air and nitrogen atmospheres. Poly(aryl ether phthalazine)s undergo an exothermic reaction above the glass transition temperature. The major product of this reaction is a rearrangement of the phthalazine moieties to quiazoline moieties, however some crosslinking of the polymers occurs. Cured samples of the poly(aryl ether phthalazine)s show a small increase in the polymer T_g and are insoluble in all solvents tested. © 1996 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 34:1897–1905, 1996     

Synthesis and physical properties of poly(aryl ether)s containing diphenylacetylene moieties

Poly(aryl ether)s containing diphenylacetylene moieties in the backbone have been synthesized. When the polymers are heated an exothermic reaction, resulting from reaction of the acetylene units, occurs in the range 380- 434°C and the polymers undergo a cross-linking reaction. Polymers cross-linked at 340°C exhibit Tg increases from 2°C to complete disappearance of the Tg depending on the concentration of the diphenylacetylene group which has been incorporated into the polymer. In most cases films of the cross-linked polymers are still flexible and exhibit Young's moduli in the range 1.2-2.1 GPa at 200°C. The solubility or the amount of swelling of these cross-linked polymers in solvents depends on the mol % of diphenylacetylene groups incorporated in the polymer backbone. Copolymers have also been synthesized.     

Synthesis and characterization of poly(aryl ether)s containing the pyrimidine moiety

A series of new poly(aryl ether)s containing the pyrimidine moiety were prepared by a nucleophilic aromatic substitution polymerization reaction in an aprotic solvent (DMAc) in the presence of excess potassium carbonate. These polymers are high molecular weight, amorphous, and soluble in common solvents at room temperature. The polymers are easily cast from solution into flexible, colorless, and transparent films. They showed high glass transition temperatures ranging from 198 to 304°C by DSC analysis. The 5% weight losses by thermogravimetric analysis ranged from 478 to 580°C, indicating that these polymers are very thermostable in nitrogen and air. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1107–1110, 1998     

Synthesis and characterization of new soluble poly（aryl ether nitrile）s containing phthalazinone moiety

A series of novel poly（aryl ether nitrile）s containing phthalazinone moiety were synthesized by the nucleophilic displacement reaction of bisphenol-like monomers （I） with 2,6-difluorobenzonitrile. The inherent viscosities ranged from 0.46 to 1.07 dL g^-1. The glass transition temperatures were in the range of 277-295℃, and the temperatures for 10% weight loss in nitrogen atmosphere were found between 495 and 527 ℃. The structures of these resultant polymers were confirmed by FT-IR and 1^H NMR. Moreover, the properties of poly（aryl ether nitrile）s including solubility and crystallinity were also studied.     

Novel poly(aryl ether phthalazinium) ionomers and their properties

The synthesis of N-phenyl phthalazinium salts by condensation of a 1,2-diaroylbenzene with phenylhydrazine is described. This reaction was utilized to prepare novel poly(aryl ether phthalazinium) ionomers by the direct condensation of poly(aryl ether ketone)s with phenylhydrazine. The preparation of poly(aryl ether phthalazinium) ionomers by methylation of poly(aryl ether phthalazine)s is also described. Most of the ionomers are amorphous, thermally stable, and soluble in organic solvents. They can be cast into flexible and strong films. The glass transition temperature of the ionomers ranges from 297 to 363°C, an increase of 12 to 100°C over the corresponding neutral polymers. © 1996 John Wiley & Sons, Inc.     

Novel fluorinated poly(aryl ether ketone)s

Two novel fluorinated monomers were prepared and polymerized with biphenols to produce amorphous, thermally stable poly(aryl ether ketone)s. The properties of the fluorinated polymers are compared to those of unfluorinated, amorphous poly(aryl ether ketone)s. The presence of fluorine in the polymers was found to cause a decrease in glass transition temperature and Young's moduli, however, no increase in thermal stability was observed. The fluorinated polymers are soluble in common organic solvents such as chloroform and methylene chloride at room temperature, and also show solubility in solvents containing a ketonic moiety, such as acetone. Evidence of polymer branching through fluorines considered to be unreactive under the polymerization conditions was found. Efforts were made to evaluate the reactivity of fluorine atoms under the polymerization conditions using both molecular modeling and ¹⁹F-NMR to ascertain if such branching could be avoided. © 1995 John Wiley & Sons, Inc.     

Synthesis and properties of fluorine‐containing poly(aryl ether oxadiazole)s

Fluorine‐containing poly(aryl ether 1,3,4‐ozadiazole)s were synthesized by the nucleophilic aromatic substitution reaction of 2,5‐bis(2,3,4,5,6‐pentafluorophenyl)‐1,3,4‐oxadiazole and various bisphenols in the presence of potassium carbonate. The polymerizations were carried out at 30 °C in 1‐methyl‐2‐pyrrolidinone to avoid the gelation caused by a crosslinking reaction at para and ortho carbons to the 1,3,4‐oxidiazole ring. The obtained polymers were all para‐connected linear structures. The obtained fluorine‐containing poly(aryl ether 1,3,4‐ozadiazole)s showed excellent solubility and afforded tough, transparent films by the solution‐casting method. They also exhibited a high glass transition temperature depending on the molecular structure, and the glass transition temperature could be controlled by the bisphenols in the range of 157–257 °C. They showed good thermal stability and excellent hydrophobicity due to the incorporation of the 2,3,5,6‐tetrafluoro‐1,4‐phenylene moiety. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2855–2866, 2007     

Synthesis of photoreactive poly(ether ether ketone)s containing alkyl groups

Poly(ether ether ketone)s containing alkyl groups were prepared by nucleophilic substitution reaction of alkyl-substituted difluoro diaryl ethers with hydroquinone or by electrophilic substitution reaction of alkyl-substituted diaryl ether with 4,4′-oxydibenzoic acid in PPMA. Polycondensations proceeded smoothly and produced polymers having inherent viscosities up to 0.5-–1.6 dL/g. The polymers were quite soluble in strong acid, dipolar aprotic solvents, and chloroform at room temperature. Thermogravimetry of the polymers showed excellent thermal stability, indicating that 10% weight loses of the polymers were observed in the range above 450°C in nitrogen atmosphere. The glass transition temperatures of the polymers ranged from 128 to 146°C. Furthermore, Polymer 3b functioned as a photosensitive resist of negative type for UV radiation. The resist had a sensitivity of 42 mJ/cm² and a contrast of 2.5, when it was postbaked at 100°C for 10 min, followed by development with THF/acetone at room temperature. © 1996 John Wiley & Sons, Inc.     

Resistive switching polymer materials based on poly(aryl ether)s containing triphenylamine and 1,2,4‐triazole moieties

A series of poly(aryl ether)s were successfully prepared via aromatic nucleophilic substitution reaction from various bisphenols and a novel bipolar aryl difluoride monomer containing electron‐donor triphenylamine and electron‐acceptor 1,2,4‐triazole moieties. The poly(aryl ether)s exhibited excellent solubility in organic solvents such as dimethylformamide, chloroform, and tetrahydrofuran at room temperature. The poly(aryl ether)s showed high thermal stability with T_d10 higher than 500 °C and glass transition temperatures (T_g) higher than 187 °C. The thin films of the poly(aryl ether)s indicated bistable resistive switching behavior with ON/OFF current ratios as high as 10³. The switching on and switching off bias voltages of the poly(aryl ether)s were affected by the bisphenol moiety. The good resistive switching behavior of the poly(aryl ether)s made them promising candidates for future nonvolatile memory applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6861–6871, 2008     

Synthesis and properties of novel poly(arylene ether)s and poly(arylene thioether)s based on a pyridazine biphenol or a phthalazine biphenol

Novel sulfur‐containing biphenol monomers were prepared in high yields by the reaction of 4‐mercaptophenol with chloropyridazine or chlorophthalazine compounds. High‐molecular‐weight poly(arylene ether)s were synthesized by a nucleophilic substitution reaction between these sulfur‐containing monomers and activated difluoro aromatic compounds. The inherent viscosities of these polymers ranged from 0.34 to 0.93 dL/g. The poly(pyridazine)s exhibited glass‐transition temperatures greater than 165 °C. The poly(phthalazine)s showed higher glass‐transition temperatures than the poly(pyridazine)s. A polymer synthesized from a bisphthalazinebiphenol and bis(4‐fluorophenyl)sulfone had the highest glass‐transition temperature (240 °C). The thermal stabilities of the poly(pyridazine)s and poly(phthalazine)s showed similar patterns of decomposition, with no significant weight loss below 390 °C. The poly(phthalazine)s were soluble in chlorinated solvents such as chloroform, and the poly(pyridazine)s were soluble in dipolar aprotic solvents such as N,N′‐dimethylacetamide. The soluble poly(pyridazine)s and poly(phthalazine)s could be cast into flexible films from solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 262–268, 2007     

Sulfonated poly(aryl ether ether ketone ketone)s containing fluorinated moieties as proton exchange membrane materials

A series of sulfonated poly(aryl ether ether ketone ketone)s statistical copolymers with high molecular weights were synthesized via an aromatic nucleophilic substitution polymerization. The sulfonation content (SC), defined as the number of sulfonic acid groups contained in an average repeat unit, could be controlled by the feed ratios of monomers. Flexible and strong membranes in sodium sulfonate form could be prepared by the solution casting method, and readily transformed to their proton forms by treating them in 2 N sulfuric acid. The polymers showed high T_gs, which increased with an increase in SC. Membranes prepared from the present sulfonated poly(ether ether ketone ketone) copolymers containing the hexafluoroisopropylidene moiety (SPEEKK‐6F) and copolymers containing the pendant 3,5‐ditrifluoromethylphenyl moiety (SPEEKK‐6FP) had lower water uptakes and lower swelling ratios in comparison with previously prepared copolymers containing 6F units. All of the polymers possessed proton conductivities higher than 1 × 10^?2 S/cm at room temperature, and proton conductivity values of several polymers were comparable to that of Nafion at high relative humidity. Their thermal stability, oxidative stability, and mechanical properties were also evaluated. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2299–2310, 2006     

Poly(arylene ether)s and poly(arylene thioether)s containing the 1,2-dihydro-4-phenyl(2H)- phthalazinone moiety

A series of new high molecular weight poly(arylene ether)s containing the 1,2-dihydro-4-phenyl(2H)phthalazinone moiety have been synthesized. The inherent viscosities of these polymers are in the range of 0.33–0.64 dL/g. They are amorphous and readily soluble in chloroform, DMF, and DMAc. The glass transition temperatures of the polymers range from 241 to 320°C and the 5% weight loss temperatures in nitrogen atmosphere range from 473 to 517°C. The hydroxy group in the monomer 1,2-dihydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one has been selectively transformed into the N,N′-dimethylthiocarbamate group, which was then rearranged to give the S-(N,N′-dimethylcarbamate) group via the Newman–Kwart rearrangement reaction. A series of poly(arylene thioether)s containing the 1,2-dihydro-4-phenyl(2H)phthalazinone moiety have also been synthesized via two types of reactions, a N C coupling reaction and a one-pot reaction between the S-(N,N′-dimethylcarbamate) and activated dihalo compounds, in diphenyl sulfone in the presence of a cesium carbonate and calcium carbonate mixture. These poly(arylene thioether)s also have high glass transition temperatures (ranging from 217–303°C) and high thermal stabilities. Compared with their poly(ether) analogs, the poly(arylene thioether)s have glass transition temperatures several degrees lower, which is attributed to the more flexible C S C bonds. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36 : 455–460, 1998     

Synthesis and characterization of fluorinated poly(aryl ether ketone)s containing 1,4-naphthalene moieties

The new monomer 2,2-bis[4-(4-{4-fluorobenzoyl}-1-naphthoxy)phenyl]hexafluoropropane ( 2 ) was synthesized in a two-step reaction sequence. 2,2-his[4-(1-naphthoxy)phenyl]-hexafluoropropane ( 1 ) was prepared using the Ullmann ether synthesis reaction of 4,4-(hex-afluoroisopropylidiene)diphenol with 1-bromonaphthalene. Friedel-Crafts acylation of 1 with 4-fluorobenzoyl chloride in methylene chloride containing dimethylsulfone selectively afforded 2 in 82% yield. The polycondensation of 2 with various bisphenols in DMAc in the presence of an excess of potassium carbonate as a condensation reagent was carried out at 165°C to quantitatively afford the corresponding fluorinated poly(aryl ether ketone)s containing 1,4-naphthalene moieties. Thermal analysis of the polymers showed them to have T_gs ranging from 194 to 230°C and to be thermally stable in air up with initial weight losses at about 500°C. In addition, these novel polymers exhibited excellent solubility in organic solvents including NMP, DMAc, and chloroform. © 1997 John Wiley & Sons, Inc.     

Co‐poly(aryl ether sulfone)s containing phthalimidine moiety in the main chain

Several new co‐poly(arylene ether sulfone)s have been prepared by the reaction of 4,4′‐fluorodiphenyl sulfone (FDS) with different bisphenols namely 4,4′‐isopropylidenediphenol (BPA), 4,4′‐hexafluoroisopropylidenediphenol (6F‐BPA), and N‐phenyl‐3,3‐bis(4‐hydroxyphenyl)phthalimidine(PA). The homo‐poly(arylene ether sulfone)s are named as 1a, 2a, and 3a. The copolymers namely 2b, 2c, 2d and 3b, 3c, 3d have been prepared, respectively, on reaction of FDS with BPA or 6F‐BPA using different molar ratios of PA such as 25, 50, and 75. The poly(aryl ether sulfone)s 1a containing PA unit in the main chain showed a very high glass transition temperature of 280°C and an outstanding thermal stability up to 510°C for 5% weight loss under synthetic air. Depending on the mole% of PA, the glass transition temperatures of the copolymers can be varied. The polymers were soluble in a wide range of organic solvents. Transparent thin films of these polymers exhibited tensile strengths upto 84 MPa and Young's modulus up to 3.16 GPa. The films of these polymers showed low water absorption of 0.24%. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and crosslinking of poly (aryl ether)s containing 1,1-diphenylethylene moieties

Poly (aryl ether)s containing the diphenylethylene moiety, synthesized from 1,1-bis(4-fluo-rophenyl)ethylene or 1,1-bis(4-hydroxyphenyl)ethylene, are thermally crosslinkable. Char-acterization and crosslinking studies of these polymers were carried out by GPC, DSC, TGA, and NMR. The solvent resistance and T_g's of the resulting crosslinked networks increase after crosslinking. Thermogravimetric analysis shows that no significant mass loss accompanies the crosslinking reaction. © 1995 John Wiley & Sons, Inc.     

Poly(aryl ether amide)s

A general method for the preparation of poly(aryl ether amide)s has been developed where the generation of an aryl ether linkage is the polymer-forming reaction. The amide linkage was found to be sufficiently electron-withdrawing to activate halo-substituents towards nucleophilic aromatic substitution analogous to conventional activating groups (i.e., sulfone, ketone, etc.). Model reactions demonstrated that the amide-activated displacement occurred with high selectivity in near quantitative yield and was judged suitable as a polymer-forming reaction. Appropriately fluoro-substituted amides were prepared and subjected to displacement polymerization with bisphenoxides in a N-methyl-2-pyrrolidone (NMP)/N-cyclohexyl-2-pyrrolidone (CHP) solvent mixture. High molecular weight polymers with glass transition temperatures in the 200–225°C range were obtained. © 1993 John Wiley & Sons, Inc.     

Synthesis and characterization of new poly(aryl ether)s with isolated fluorophores

Four novel poly(aryl ether)s ( P1 – P4 ) consisting of alternate isolated electron‐transporting (3,3″′‐bis‐trifluoromethyl‐p‐quaterphenyl for P1 , P3 or 3,3″′‐dicyano‐p‐quaterphenyl for P2 , P4 ) and hole‐transporting fluorophores [N‐(2‐ethylhexyl)‐3,6‐bis(styryl)carbazole for P1 , P2 or 9,9‐dihexyl‐2,7‐bis(styryl)fluorene for P3 , P4 ] were synthesized and characterized. These poly(aryl ether)s can be dissolved in organic solvents and exhibited good thermal stability with 5% weight‐loss temperature above 500 °C in nitrogen atmosphere. The photoluminescent (PL) spectra of the films of these polymers showed maximum peaks at around 442–452 nm. The PL spectral results revealed that the emission of polymers was dominated by the fluorophores with longer emissive wavelength via the energy transfer from p‐quaterphenyl to 3,6‐bis(styryl)carbazole or 2,7‐bis(styryl)fluorene segments. Therefore, the p‐quaterphenyl segments function only as the electron‐transporting/hole‐blocking units in these polymers, and the other segments are the emissive centers and hole‐transporting units. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital energy levels of these polymers were measured by cyclic voltammetry. The electron‐donating nitrogen atom on carbazole resulted in the higher HOMO energy levels of P1 and P2 than those of P3 and P4 . The single‐layer light‐emitting diodes (LED) of Al/poly(aryl ether)s ( P1 – P4 )/ITO glass were fabricated. P1 , P2 , and P4 revealed blue electroluminescence, but P3 emitted yellow light as a result of the excimer emission. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2215–2224, 2002     

Fluorescent poly(aryl ether)s containing benzo[g]phthalazine and benzo[g]isoquinoline moieties

2,3‐Bis(4‐fluorobenzoyl)naphthalene was synthesized, and poly(aryl ether)s were prepared through a reaction with various bisphenols in the solvent N,N‐dimethylacetamide in the presence of potassium carbonate. Through a reaction with hydrazine or benzylamine, the corresponding benzo[g]phthalazine or benz[g]isoquinoline was formed. The conversion into heterocyclic structures resulted in a significant straightening of the chains, and the glass‐transition temperatures, inherent viscosities, and apparent molecular weights from size exclusion chromatography were significantly increased, whereas the solubilities decreased. The diketone‐containing polymers were colorless, and the benzo[g]phthalazine‐ and benz[g]isoquinoline‐containing polymers were yellow. The diketone polymers showed strong UV absorption maxima up to 350 nm, with fluorescence emission maxima around 475 nm. The heterocyclic polymers had broad absorptions up to around 450 nm, with strong emission maxima around 550 nm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5745–5753, 2004     

Thianthrene as an activating group for the synthesis of poly(aryl ether thianthrene)s by nucleophilic aromatic substitution

A method for the preparation of poly(aryl ether thianthrene)s has been developed in which the aryl ether linkage is generated in the polymer‐forming reaction. The thianthrene heterocycle is sufficiently electron‐withdrawing to allow fluoro displacement with phenoxides by nucleophilic aromatic substitution. The monomer for this reaction, 2,7‐difluorothianthrene, can be synthesized in a moderate yield by a simple reaction sequence. Semiempirical calculations at the PM3 level suggest that 2,7‐difluorothianthrene is sufficiently activated, whereas NMR spectroscopy (¹H and ¹³C) indicates that the monomer is only slightly activated or (¹⁹F) not sufficiently activated for nucleophilic aromatic substitution. Model reactions with p‐cresol have demonstrated that the fluorine atoms on 2,7‐difluorothianthrene are readily displaced by phenoxides in high yields, and the process has been deemed suitable for polymer‐forming reactions. High‐molecular‐weight polymers have been produced from bisphenol A, bisphenol AF, and 4,4′‐biphenol. The polymers have been characterized with gel permeation chromatography, NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. The glass‐transition temperatures for the polymers of different compositions and molecular weights range from 138 to 181 °C, and all the polymers have shown high thermooxidative stability, with 5% weight loss values in an air environment approaching 500 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6353–6363, 2004     

Synthesis and properties of poly(arylene ether imide ketone)s

Poly(arylene ether ketone)s containing imide units were prepared by the aromatic nucleophilic displacement reaction of the potassium salts of bisphenols with bis(4-fluorobenzoyl)phthalimides in N-methyl-2-pyrrolidone at elevated temperature. The polymers having inherent viscosities of 0.34–0.77 dL/g were obtained in 2 h. The polymers exhibited glass transition temperatures ranging from 216 to 268°C and decomposition temperatures (5% weight loss under air atmosphere) ranging from 450–570°C mainly depending on the bisphenols used in the polymer synthesis. The isothermal TGA measurements (400°C under air or nitrogen atmosphere) revealed that the 4,4'-biphenol- and hydroquinone-based poly(arylene ether ketone imide)s belong to a superior class of heat resistant polymers. The mechanical properties of these polymers are also described. © 1994 John Wiley & Sons, Inc.