Synthesis and characterization of novel poly(ester‐carbonate)s by copolymerization of trans‐4‐hydroxy‐L‐proline with cyclic carbonate

The melt ring‐opening/condensation reaction of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L‐proline (N‐CBz‐Hpr) with cyclic carbonate [trimethylene carbonate (tri‐MC) or tetramethylene carbonate (tetra‐MC)] at a wide range of molar fractions in the feed produced new degradable poly(ester‐carbonate)s. The influence of reaction conditions such as polymerization time and temperature on the yield and inherent viscosity of the copolymers was investigated. The polymerizations were carried out in bulk at 140 °C with 1.5 wt % stannous octoate as a catalyst for 30 h. The poly(ester‐carbonate)s obtained were characterized by Fourier transform infrared spectroscopy, ¹H NMR, differential scanning calorimetry, gel permeation chromatography, and Ubbelohde viscometry. The copolymers synthesized exhibited moderate molecular weights with rather narrow molecular weight distributions. The values of the glass‐transition temperature (T_g) of the copolymers depend on the molar fractions of cyclic carbonate. For the poly(N‐CBz‐Hpr‐co‐tri‐MC) system, with a decreased tri‐MC content from 93 to 16 mol %, the T_g increased from ?10 to 60 °C. Similarly, for the poly(N‐CBz‐Hpr‐co‐tetra‐MC) system, when the tetra‐MC content decreased from 80 to 8 mol %, the T_g increased from ?18 to 52 °C. The relationship between the poly(N‐CBz‐Hpr‐co‐tri‐MC) T_g and the compositions was in approximation with the Fox equation. In vitro degradation of these poly(N‐CBz‐Hpr‐co‐tri‐MC)s was evaluated from weight‐loss measurements. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1435–1443, 2003     

Synthesis and in vitro degradation of poly(alkylene carbonate anhydride)

A novel degradable poly(alkylene carbonate anhydride) (PACA) was synthesized by the melt polycondensation reaction of the corresponding mixed anhydrides of the dicarboxylic acid derived from oligo(tetramethylene carbonate)diol (OTMCD) and oligo(hexamethylene carbonate)diol (OHMCD). The polymer's structure was confirmed by IR and ¹H NMR spectroscopy. DSC analysis showed PACA had a low T_g (< –30°C). In vitro degradation tests indicated that the degradation rate of poly(alkylene carbonate) was more controlled with the incorporation of anhydride groups.     

Synthesis and properties of poly(hydroxyurethane)s

Bis(cyclic Carbonate)s 1 were prepared by the reaction of bis(epoxide)s and atmospheric pressure of CO₂ in the presence of sodium iodide and triphenylphosphine as catalysts at 100°C in high yield. Polyaddition of 1 and hexamethylenediamine ( 2a ) or dodecamethylenediamine ( 2b ) in dimethylsulfoxide or N,N-dimethylacetamide (DMAc) at 70 or 100°C for 24 h afforded corresponding poly(hydroxyurethane)s with M?_n 20,000–30,000. When ethylenediamine ( 2c ) or 1,3-propanediamine ( 2d ) was used as a diamine, poly(hydroxyurethane)s with lower molecular weight were obtained. The presence of water, methanol, or ethyl acetate in the solvent had little effect on the M?_n of the polymer obtained, because of the high chemoselectivity of the reaction of the five-membered cyclic carbonate and amine. Polyaddition of bis(cyclic carbonate) bearing ester groups and 2a also afforded the corresponding poly(hydroxyurethane) without aminolysis of the ester groups. Poly(hydroxyurethane) 3 obtained from the bis(cyclic carbonate) derived from bisphenol A was less soluble in organic solvents than model polyurethane 8 having no hydroxy groups obtained from 4,4′-isopropylidenebis(2-hydroxyethoxybenzene) and hexamethylene diisocyanate, and was thermally stable as well as 8.3 easily undertook crosslinking at room temperature by the treatment with hexamethylene diisocyanate or aluminium triisopropoxide in DMAc or tetrahydrofuran. The gel crosslinked by aluminium triisopropoxide regenerated the original polymer at room temperature by treatment with 1.5 equiv of 1.2M HCl in N-methylpyrollidinone for 1 h. © 1993 John Wiley & Sons, Inc.     

Polymers of Carbonic Acid. 16. High Molecular Weight Poly(Neopentanediol Carbonate) by Ring-Opening Polymerization with nBuSnCl3 or SnOct2 as Initiators

Abstract

Neopentanediol carbonate, NPC, was polymerized in bulk at 120°C. Either nBuSnCl₃ or Sn(II)2-ethylhexanoate (SnOct₂) were used as initiators. The reaction time and the monomer/initiator (M/I) ratio were varied. Polymerizations initiated with nBuSnCl₃ were more rapid and yielded higher molecular weights (M _n up to 150,000 and M _w up to 270,000). Furthermore, the molecular weights were almost independent of the M/I ratio, provided the reaction time was optimized. In contrast, the molecular weights of the SnOct₂-initiated polymers paralled the M/I ratios more or less. This finding and the ¹H-NMR spectra suggest that stoichiometric reactions between monomer and SnOct₂ take place, yielding polymers with covalently bound octoate and OH endgroups. Finally, the polymerizability of NPC recrystallized from CCl₄ or from tetrahydrofuran was compared. No significant difference was found when nBuSnCl₃ was used as initiator, whereas in the case of SnOct₂ a difference was observed. NPC recrystallized from CCl₄ polymerized more rapidly and gave higher molecular weights than NPC recrystallized from THF.     

Novel,biodegradable, functional poly(ester‐carbonate)s by copolymerization of trans‐4‐hydroxy‐L‐proline with cyclic carbonate bearing a pendent carboxylic group

Water‐soluble poly(ester‐carbonate) having pendent amino and carboxylic groups on the main‐chain carbon is reported for the first time. This article describes the melt ring‐opening/condensation reaction of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline (N‐CBz‐Hpr) with 5‐methyl‐5‐benzyloxycarbonyl‐1,3‐dioxan‐2‐one (MBC) at a wide range of molar fractions. The influence of reaction conditions such as catalyst concentration, polymerization time, and temperature on the number average molecular weight (M_n) and molecular weight distribution (M_w/M_n) of the copolymers was investigated. The polymerizations were carried out in bulk at 110 °C with 3 wt % stannous octoate as a catalyst for 16 h. The poly(ester‐carbonate)s obtained were characterized by Fourier transform infrared spectroscopy, ¹H NMR, differential scanning calorimetry, and gel permeation chromatography. The copolymers synthesized exhibited moderate molecular weights (M_n = 6000–14,700 g mol^?1) with reasonable molecular weight distributions (M_w/M_n = 1.11–2.23). The values of the glass‐transition temperature (T_g) of the copolymers depended on the molar fractions of cyclic carbonate. When the MBC content decreased from 76 to 12 mol %, the T_g increased from 16 to 48 °C. The relationship between the poly(N‐CBz‐Hpr‐co‐MBC) T_g and the compositions was in approximation with the Fox equation. In vitro degradation of these poly(N‐CBz‐Hpr‐co‐MBC)s was evaluated from weight‐loss measurements and the change of M_n and M_w/M_n. Debenzylation of 3 by catalytic hydrogenation led to the corresponding linear poly(ester‐carbonate), 4 , with pendent amino and carboxylic groups. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2303–2312, 2004     

New polymer syntheses. CXI. Aliphatic polyesters by the ring‐opening polycondensation of glutaric anhydride with ethylene or trimethylene carbonate

Several polycondensations of ethylene carbonate with succinic anhydride or glutaric anhydride (GA) were conducted in bulk. Low molar mass polyesters were obtained with pyridine‐type catalysts and GA. Analogous polycondensations of trimethylene carbonate (TMC) and GA were successful when quinoline, 4‐(N,N‐dimethylamino)pyridine, or BF₃ · OEt₂ was used as a catalyst. Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectra revealed the formation of cyclic oligoesters and polyesters by backbiting degradation. Monomer mixtures containing an excess of TMC yielded copoly(ester carbonate)s with number‐average molecular weights up to 16,000 Da. Analogous copoly(ester carbonate)s were obtained from TMC and 3,3′‐tetramethylene glutaric anhydride. Furthermore, combined polycondensation/ring‐opening polymerization reactions of TMC and GA with L ‐lactide or ?‐caprolactone were studied. All copolymers were characterized by viscosity measurements and by IR, ¹H, and ¹³C NMR spectroscopy. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4357–4367, 2002     

Copolymerization of ε‐caprolactone and glycolide—A comparison of bismuth(III) hexanoate and tin(II) octanoate as initiators

ε‐Caprolactone and glycolide were copolymerized in bulk either with tin(II) 2‐ethylhexanoate (SnOct₂) or with bismuth(III) n‐hexanoate (BiHex₃) as initiators and with tetra(ethylene glycol) as a coinitiator. The temperature was varied from 100 to 160 °C. The sequences were characterized with ¹H and ¹³C NMR spectroscopy. Surprisingly, it was found that higher temperatures favored the formation of alternating sequences. Furthermore, the content of alternating dyads was significantly higher when BiHex₃ was used instead of SnOct₂. An increase in reaction time caused partial randomization of the sequences regardless of the initiator. Size exclusion chromatography measurements in chloroform yielded number‐average molecular weights in agreement with the feed ratios. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3268–3277, 2005     

聚芳亚胺的合成、结构与性能

以不同的二碘化合物和芳香二胺为单体,通过两种不同的方法经缩聚反应得到了系列高分子量、低分布的聚芳亚胺。其结构由FT-IR, 1H NMR1和元素分析表征。由DSC和TG测定结果可知,该系聚合物具有较高的玻璃化转变温度(Tg＞150℃)和良好的热稳定性(TD＞400℃)。另外,该系聚合物还表现出良好的溶解性能。     

Synthesis of star‐shaped poly(D,L‐lactic acid‐alt‐glycolic acid)‐b‐poly(L‐lactic acid) with the poly(D,L‐lactic acid‐alt‐glycolic acid) macroinitiator and stannous octoate catalyst

Two types of three‐arm and four‐arm, star‐shaped poly(D,L ‐lactic acid‐alt‐glycolic acid)‐b‐poly(L ‐lactic acid) (D,L ‐PLGA50‐b‐PLLA) were successfully synthesized via the sequential ring‐opening polymerization of D,L ‐3‐methylglycolide (MG) and L ‐lactide (L ‐LA) with a multifunctional initiator, such as trimethylolpropane and pentaerythritol, and stannous octoate (SnOct₂) as a catalyst. Star‐shaped, hydroxy‐terminated poly(D,L ‐lactic acid‐alt‐glycolic acid) (D,L ‐PLGA50) obtained from the polymerization of MG was used as a macroinitiator to initiate the block polymerization of L ‐LA with the SnOct₂ catalyst in bulk at 130 °C. For the polymerization of L ‐LA with the three‐arm, star‐shaped D,L ‐PLGA50 macroinitiator (number‐average molecular weight = 6800) and the SnOct₂ catalyst, the molecular weight of the resulting D,L ‐PLGA50‐b‐PLLA polymer linearly increased from 12,600 to 27,400 with the increasing molar ratio (1:1 to 3:1) of L ‐LA to MG, and the molecular weight distribution was rather narrow (weight‐average molecular weight/number‐average molecular weight = 1.09–1.15). The ¹H NMR spectrum of the D,L ‐PLGA50‐b‐PLLA block copolymer showed that the molecular weight and unit composition of the block copolymer were controlled by the molar ratio of L ‐LA to the macroinitiator. The ¹³C NMR spectrum of the block copolymer clearly showed its diblock structures, that is, D,L ‐PLGA50 as the first block and poly(L ‐lactic acid) as the second block. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 409–415, 2002     

Synthesis and characterization of novel aliphatic polycarbonates

A new six‐membered cyclic carbonate monomer, 5‐benzyloxy‐trimethylene carbonate, was synthesized from 2‐benzyloxy‐1,3‐propanediol, and the corresponding polycarbonate, poly(5‐benzyloxy‐trimethylene carbonate) (PBTMC), was further synthesized by ring‐opening polymerization in bulk at 150 °C using aluminum isobutoxide [Al(OⁱBu)₃], aluminum isopropoxide, or stannous octanoate as an initiator. The results showed that a higher molecular weight polycarbonate could be obtained in the case of Al(OⁱBu)_3. The protecting benzyl group was removed subsequently by catalytic hydrogenation to give a polycarbonate containing a pendant hydroxyl group (PHTMC). The polycarbonates obtained were characterized by Fourier transform infrared spectroscopy, ¹H NMR,¹³C NMR, gel permeation chromatography, and DSC. NMR results of PBTMC offered no evidence for decarboxylation occurring during the propagation. The pendant hydroxyl group in PHTMC resulted in an enhancement of the hydrophilicity of the polycarbonate. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 70–75, 2002     

Hydrogenation of poly(myrcene) and poly(farnesene) using diimide reduction at ambient pressure

Ambient pressure chemical hydrogenation using p-toluene sulfonyl hydrazide (TSH) via thermal diimide formation (N₂H₂) permitted reduction of double bonds of poly(myrcene) (poly[Myr]) and poly(farnesene) (poly[Far]). Both pendent and backbone double bonds in poly(Myr) (M_n = 56 kg/mol) and poly(Far) (M_n = 62 kg/mol) synthesized by conventional free radical polymerization were hydrogenated to almost completion. Furthermore, TSH semi-batch addition efficiently hydrogenated double bonds, while avoiding undesired autohydrogenation of diimides that occurred in batch mode. Thermal stability improved for hydrogenated poly(Myr) and poly(Far), where temperature at 10% weight loss (T_10%) increased from 188 to 404°C for poly(Myr) and from 310 to 379°C for poly(Far). T_gs of poly(Myr) and poly(Far) also increased by about 10–25°C, indicating increased stiffness after hydrogenation. Finally, viscosities of poly(Myr) and poly(Far) were also increased after hydrogenation, and a greater increase was observed for poly(Myr) (by two orders of magnitude from 10² to 10⁴ Pa s) due to its M_n being much higher than its entanglement molecular weight. Poly(Far) viscosity only increased by 1.5 times after hydrogenation (~10⁴ Pa s), comparable to the poly(Myr) after hydrogenation, suggesting unsaturated poly(Far) was more entangled than unsaturated poly(Myr) because of its longer side chains.     

Synthesis and characterization of poly(L‐lactide)s and poly(D‐lactide)s of controlled molecular weight

High molecular weight poly(L ‐lactide)s (PLLAs) and poly(D ‐lactide)s (PDLAs) were synthesized in toluene at 70 °C by ring‐opening polymerization of optically pure L ‐lactide and D ‐lactide, using tin(II) 2‐ethylhexanoate (SnOct₂) and 2‐(2‐methoxyethoxy)ethanol as initiator and coinitiator, respectively. Under these conditions, polarimetry as well as ¹³C NMR spectroscopy indicated that the synthesized poly(lactide)s (PLAs) are more than 99% isotactic. The molecular weight was successfully controlled by adjusting the monomer‐to‐initiator molar ratio. Gel permeation chromatography and MALDI‐TOF mass spectrometry analyses showed that the polydispersity index of the PLAs is below 1.1. Moreover, MALDI‐TOF spectra showed two different chain distributions, one characterized by an even number of lactic acid repeat units and the other by an odd number of lactic acid repeat units. The second distribution, indicative of the presence of intermolecular transesterification reactions, appears at the very beginning of the polymerization and its intensity increases with the polymerization time. Finally, a reversible reaction kinetic model was used to determine the monomer equilibrium concentration ([M]_eq = 1.4 ± 0.5%) and the propagation rate constant (k_p = 14.4 ± 0.5 L mol^?1 h^?1) of the polymerization. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1944–1955, 2007     

Synthesis and Photosensitive Properties of Poly(aryl imino) Containing Azobenzene Group (PAI-A)

Using 4,4′‐dibromobenzophenone and 4,4′‐diaminoazobenzene as monomers, poly(aryl imino) containing azobenzene unit (PAI‐A) was synthesized via palladium‐catalyzed amination, and structurally characterized by means of FT‐IR, ¹H NMR spectra and elemental analysis, the results of which show an agreement with the proposed structure. The UV absorption spectra were tested under different conditions. Additionally, differential scanning calorimetry (DSC) and thermogravimetric (TG) measurements show that PAI‐A possesses high glass transition temperature (T_g>176°C) and good thermal stability with high decomposition temperatures in nitrogen atmosphere (T_D>410°C).     

Synthesis of three‐armed poly(trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L‐proline)‐block‐poly(ε‐caprolactone) copolymers

A series of novel types of three‐armed poly(trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline)‐block‐poly(ε‐caprolactone) (PHpr‐b‐PCL) copolymers were successfully synthesized via melt block copolymerization of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline (N‐CBz‐Hpr) and ε‐caprolactone (ε‐CL) with a trifunctional initiator trimethylolpropane (TMP) and stannous octoate (SnOct₂) as a catalyst. For the homopolycondensation of N‐CBz‐Hpr with TMP initiator and SnOct₂ catalyst, the number‐average molecular weight (M_n) of prepolymer increases from 530 to 3540 g mol^?1 with the molar ratio of monomer to initiator (3–30), and the molecular weight distribution (M_w/M_n) is between 1.25 to 1.32. These three‐armed prepolymer PHpr were subsequently block copolymerized with ε‐caprolactone (ε‐CL) in the presence of SnOct₂ as a catalyst. The M_n of the copolymer increased from 2240 to 18,840 g mol^?1 with the molar ratio (0–60) of ε‐CL to PHpr. These products were characterized by differential scanning calorimetry (DSC), ¹H NMR, and gel permeation chromatography. According to DSC, the glass‐transition temperature (T_g) of the three‐armed polymers depended on the molar ratio of monomer/initiator that were added. In vitro degradation of these copolymers was evaluated from weight‐loss measurements and the change of M_n and M_w/M_n. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1708–1717, 2005     

Effect of the composition ratio of copolymerized poly(carbonate) glycol on the microphase‐separated structures and mechanical properties of polyurethane elastomers

Randomly copolymerized poly(carbonate) glycols were employed as starting materials for the synthesis of polyurethane elastomers (PUEs). The poly(carbonate) glycols had hexamethylene (C₆) and tetramethylene (C₄) units between carbonate groups in various composition ratios (C₄/C₆ = 0/100, 50/50, 70/30, and 90/10), and the number‐average molecular weights of these poly(carbonate) glycols were 1000 and 2000. The PUEs were synthesized with these poly(carbonate) glycols, 4,4′‐diphenylmethane diisocyanate, and 1,4‐butanediol by a prepolymer method. Differential scanning calorimetry measurements revealed that the difference between the glass‐transition temperature of the soft segment in the PUEs and the glass‐transition temperature of the original glycol polymer decreased and the melting point of the hard‐segment domain increased with an increasing C₄ composition ratio. The microphase separation of the poly(carbonate) glycol‐based PUEs likely became stronger with an increasing C₄ composition ratio. Young's modulus of these PUEs increased with an increasing C₄ composition ratio. This was due to increases in the degree of microphase separation and stiffness of the soft segment with an increase in the C₄ composition ratio. The molecular weight of poly(carbonate) glycol also influenced the microphase‐separated structure and mechanical properties of the PUEs. The addition of different methylene chain units to poly(carbonate) glycol was quite effective in controlling the microphase‐separated structure and mechanical properties of the PUEs. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4448–4458, 2004     

The effect of molecular weight on the crystallization kinetics and equilibrium melting temperature of poly(tetramethylene ether glycol)

Isothermal crystallization of poly(tetramethylene ether glycol) (PTMEG) with relatively low molecular weight (M_n = 991, 2004 and 2864, respectively) was investigated by differential scanning calorimetry, and the equilibrium melting temperature (T) determined using the Hoffman–Weeks analysis. The crystallization kinetics of PTMEG were characterized using an Avrami analysis. Mechanistic n values ranged from 2.2 to 2.9 for the primary crystallization process for three molecular weight grades, indicating heterogeneous nucleation of spherulites. Polarized light microscopy confirmed that PTMEG crystallized by the growth of spherulites from heterogeneous nuclei. The half–life for crystallization (t_1/2) and the composite rate constant were found to be dependent on the degree of supercooling (ΔT) and the molecular weight. Copyright © 2006 John Wiley & Sons, Ltd.     

Synthesis and characterization of aromatic poly(ether ketone)s containing cyclotriphosphazene units

Bis(4-oxybenzoic acid) tetrakis(phenoxy) cyclotriphosphazene (IUPAC name: 4-[4-(carboxyphenoxy)-2,4,6,6-tetraphenoxy-1,3,5,2λ⁵,4λ⁵,6λ⁵-triazatriphosphinin-2-yl]oxy-benzoic acid) was synthesized and direct polycondensed with diphenylether or 1,4-diphenoxybenzene in Eaton's reagent at the temperature range of 80–120°C for 3 hours to give aromatic poly(ether ketone)s. Polycondensations at 120°C gave polymer of high molecular weight. Incorporation of cyclotriphosphazene groups in the aromatic poly(ether ketone) backbone greatly enhanced the solubility of these polymers in common organic polar solvents. Thermal stabilities by TGA for two polymer samples of polymer series ranged from 390 to 354°C in nitrogen at 10% weight loss and glass transition temperatures (T_g) ranged from 81.4 to 89.6°C by DSC. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1227–1232, 1998     

Alternating copolymerization of cyclohexene oxide and carbon dioxide under cobalt porphyrin catalyst

Cobalt porphyrin complexes（TPPCo^ⅢX）（TPP = 5,10,15,20-tetraphenyl-porphyrin;X = halide） in combination with bis（triphenylphosphine） iminium chloride（PPNCl） were used for the copolymerization of cyclohexene oxide and CO₂. The highest turnover frequency of 67.2 h^-1 was achieved after 13 h at 20℃,and the obtained poly（1,2-cyclohexylene carbonate）（PCHC） showed number average molecular weight（M_n） of 10×10³.Though the obtained PCHC showed atactic structure,the m-centered tetrads content reached 58.1%at CO₂ pressure of 1.0 MPa,and decreased to 51.9%at CO₂ pressure of 6.0 MPa,indicating that it was inclined to form atactic polymer at high CO₂ pressure.     

Effect of prepolymer molecular weight on solid state polymerization of poly(bisphenol a carbonate) with nitrogen as a sweep fluid

The effect of prepolymer molecular weight on the solid‐state polymerization (SSP) of poly(bisphenol A carbonate) was investigated using nitrogen (N₂) as a sweep fluid. Prepolymers with different number–average molecular weights, 3800 and 2400 g/mol, were synthesized using melt transesterification. SSP of the two prepolymers then was carried out at reaction temperatures in the range 120–190 °C, with a prepolymer particle size in the range 20–45 μm and a N₂ flow rate of 1600 mL/min. The glass transition temperature (T_g), number–average molecular weight (M_n), and percent crystallinity were measured at various times during each SSP. The phenyl‐to‐phenolic end‐group ratio of the prepolymers and the solid‐state synthesized polymers was determined using 125.76 MHz ¹³C and 500.13 MHz ¹H nuclear magnetic resonance (NMR) spectroscopy. At each reaction temperature, SSP of the higher‐molecular‐weight prepolymer (M_n = 3800 g/mol) always resulted in higher‐molecular‐weight polymers, compared with the polymers synthesized using the lower molecular weight prepolymer (M_n = 2400 g/mol). Both the crystallinity and the lamellar thickness of the polymers synthesized from the lower‐molecular‐weight prepolymer were significantly higher than for those synthesized from the higher‐molecular‐weight prepolymer. Higher crystallinity and lamellar thickness may lower the reaction rate by reducing chain‐end mobility, effectively reducing the rate constant for the reaction of end groups. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4959–4969, 2008     

Thermal analysis of the double-melting behavior of poly(L-lactic acid)

The melting and crystallization behavior of poly(L -lactic acid) (PLLA; weight-average molecular weight = 3 × 10⁵) was studied with differential scanning calorimetry (DSC). DSC curves for PLLA samples were obtained at various cooling rates (CRs) from the melt (210 °C). The peak crystallization temperature and the exothermic heat of crystallization determined from the DSC curve decreased almost linearly with increasing log(CR). DSC melting curves for the melt-crystallized samples were obtained at various heating rates (HRs). The double-melting behavior was confirmed by the double endothermic peaks, a high-temperature peak (H) and a low-temperature peak (L), that appeared in the DSC curves at slow HRs for the samples prepared with a slow CR. Peak L increased with increasing HR, whereas peak H decreased. The peak melting temperatures of L and H [T_m(L) and T_m(H)] decreased linearly with log(HR). The appearance region of the double-melting peaks (L and H) was illustrated in a CR–HR map. Peak L decreased with increasing CR, whereas peak H increased. T_m(L) and T_m(H) decreased almost linearly with log(CR). The characteristics of the crystallization and double-melting behavior were explained by the slow rates of crystallization and recrystallization, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 25–32, 2004