Determination of Trace Butyltin Compounds in Sea Water by Gas Chromatography-Atomic Absorption Spectrometry

A gas chromatography-atomic absorption spectrometric (GC-AAS) method has been developed for the determination of trace butyltin compounds in sea water. Aqueous butyltin compounds were reduced to the volatile hydride forms by NaBH₄ and were extracted with dichloromethane simultaneously. The dichloromethane extract was concentrated under reduced pressure, followed by direct injection into the GC-AAS system for analysis. The butyltin species were separated with a 2-m glass column packed with 2% OV-101 on Chromosorb G HP (100-120 mesh). Following GC separation, each species was transferred into an electrothermally heated (800 °C) quartz furnace for atomization. The tin atoms produced from individual butyltin compound were detected at 224.6 nm by an atomic absorption spectrometer. With a sea water sample (1 L), the detection limits (3σ) for monobutyltin, dibutyltin and tributyltin were approximately 20, 20 and 70 ng Sn L^?1, respectively. The method has been applied to the analysis of trace butyltin compounds in the sea water of Keelung Harbor.     

Direct Grignard pentylation of organotin-contaminated lard samples followed by capillary gas chromatography with flame photometric detection

During a recent investigation of the organotin-contaminated lard samples, a simple method was developed by direct Grignard pentylation of lard samples and capillary gas chromatography with flame photometric detection using quartz surface-induced tin emission. Using HP-1 capillary column with temperature programming and FPD detector, pentylated tri-, di-, monometyltin, dioctyltin and Sn(IV) can be base-line separated and detected within 20 min. The analysis of pentylated tin compounds by GC-MS confirmed the existence of methyltins and inorganic tin in lard samples, which was agreeable with the results obtained by GC-FPD. The content of organotin compounds was calculated by internal standard method in which methyltripropyltin (MeSnPr3) acted as internal standard. The results showed that these samples were heavily contaminated with mg/g levels of dimethyltin, microg/g levels of tri- and monomethyltin. Among them, one sample contained mg/g level of dioctyltin and one contained a little of inorganic form of Sn(IV). The recoveries of tri-, di- and monomethyltin were 95.7%, 105.5% and 105.7%, respectively.     

Analysis of organotin compounds by gas chromatography-reactive-flow detection.

The gas chromatographic (GC) reactive-flow detector (RFD) responds strongly to organotin compounds. The system yields over four orders of linearity with a minimum detectable amount of 8 x 10(-16) g Sn/s (at S/N = 2). The RFD's selectivity towards tin over carbon is approximately 2.5 x 10(5) g C/g Sn. The spectral emission includes a surface luminescence centered at 390 nm and a gas-phase luminescence centered at 470 nm. These findings suggest that the GC-RFD could serve as a sensitive and selective tool for the analysis of organotin compounds.     

Determination of Butyltins in Sea Water by Gas Chromatography with Flame Photometric Detection

Use of a gas chromatograph with a flame-photometric detector (GC-FPD) is described to determine butyltin compounds in sea water. The butyltins in an acidified water sample (pH 3.0) are first complexed with tropolone, followed by solid-phase extraction (SPE) with a tropolone-treated C₁₈ cartridge. HCI at a small concentration is then added to the concentrated SPE eluate before GC analysis. This procedure is simple and off-column derivatization of analytes is not required. The organotins, viz. mono-, di- and tributyltin, are separated as their respective chlorides on a capillary column (HP-1) and are detected with a flame-photometric detector and an interference filter at 610 nm. Recoveries of the three butyltin species are quantitative (> 90%). Based on a sea water sample 200-mL, the detection limits for mono-, di- and tributyltin are 6,4 and 3 ng tin L^?1, respectively. This method is applied to analysis of trace butyltins in various samples of sea water.     

Speciation analysis of triethyl-lead and tributyl-tin compounds in human urine by liquid-liquid extraction and gas chromatography microwave-induced plasma atomic emission detection

This work describes the development of a fast method for speciation analysis of triethyl-lead and tributyl-tin species in urine samples after in situ derivatization by tetraethyl- or tetrapropyl-borate reagents. The alkylation reaction is done in the aqueous and urine medium and the less-polar derivatives are extracted in hexane by liquid-liquid extraction. The species were extracted and the extract was efficiently collected from the aqueous phase after centrifugation. Finally, the organometallic species are separated by gas chromatography and determined from the emission signals of elemental lead and tin. Atomic lead and tin are formed from the organolead and organotin compounds during atomization of the column eluate in a microwave-induced helium plasma source. The simultaneous measurement of lead (Pb) at 405.780 nm and tin (Sn) at 303.419 nm was achieved by an atomic emission detector. Finally, the analytes were determined with satisfactory precision (<5%) and detection limits of 0.05 μg Pb/L and 0.48 μg Sn/L, respectively, when 10 mL of urine is extracted with 1 mL of hexane and 1 μL of extract is injected.     

Dioctyltin and tributyltin detection at trace levels in water and beverages by capillary gas chromatography with flame photometric detection

A simple chromatographic procedure has been developed for the sensitive determination of dioctyltin and tributyltin compounds in water and beverages. Dioctyltin and tributyltin react with NaBH₄ at pH 5 to produce volatile hydrides which can be quantitatively extracted into CH₂Cl₂. The corresponding dioctyltin hydride derivative is identified by HPLC-ES-MS and measured by flame photometric detection using the quartz surface-induced tin emission. Detection limits of less than 0.7 pg of tributyltin and 10 pg of dioctyltin were achieved. Results showed that up to 9.5 ng/mL levels of dioctyltin were present in beverages. Received: 20 July 1998 / Revised: 26 August 1998 / Accepted: 28 August1998     

Characterization of organotin species using microbore and capillary liquid chromatographic techniques with an epifluorescence microscope as a novel imaging detector

The novel application of a UV epifluorescence microscope as an imaging detector for microbore and capillary high-performance liquid chromatography (HPLC) is reported. The microscope is focused on an in-line quartz flow cell incorporated down stream of a microbore HPLC column or directly on an optically clear portion of fused-silica capillary columns for analyte detection. The effect of different fluorescent ligand to analyte ratios on detection limits is also reported, as well as the effect of different image volume sizes produced by changes in microscope objective lens magnification power. Determination of relative sensitivities an detection limits for methyl- and butyltin compounds, complexed with fluorescent dyes, reveals that the organotins show decreasing sensitivity as the number of alkyl substituents on the tin atom increases, with minimum detectable amounts of 6-160 pg of analyte-ligand complex.     

Dioctyltin and tributyltin detection at trace levels in water and beverages by capillary gas chromatography with flame photometric detection

A simple chromatographic procedure has been developed for the sensitive determination of dioctyltin and tributyltin compounds in water and beverages. Dioctyltin and tributyltin react with NaBH₄ at pH 5 to produce volatile hydrides which can be quantitatively extracted into CH₂Cl₂. The corresponding dioctyltin hydride derivative is identified by HPLC-ES-MS and measured by flame photometric detection using the quartz surface-induced tin emission. Detection limits of less than 0.7 pg of tributyltin and 10 pg of dioctyltin were achieved. Results showed that up to 9.5 ng/mL levels of dioctyltin were present in beverages. Received: 20 July 1998 / Revised: 26 August 1998 / Accepted: 28 August1998     

A simplified procedure for the determination of butyltin species in water

A method is described for the analysis of solutions containing inorganic tin and butyltin compounds. It can be used to determine total tin at a concentration of 20 ng dm^?3 using a 5 dm³ sample. The method is based on solvent extraction with dichloromethane containing tropolone and determination of the tin as inorganic tin by atomic absorption spectroscopy using electrothermal atomization. The extracted butyltin compounds can be separated by paper chromatography and the tin content of the individual spot determined as above. Observations on the stability of butyltin compounds in water at the ～2 mg dm^?3 (Sn) are included.     

Determination of butyltin compounds in environmental samples by isotope-dilution GC–ICP–MS

Isotope-dilution analysis in combination with GC-ICP-MS detection has been applied to the determination of butyltin species in environmental samples. Different spikes containing the isotopically labeled butyltin species have been synthesized in the laboratory after optimization of the reaction conditions. The isotopic compositions of the tin species in the different spike solutions were determined by GC-ICP-MS after derivatization by aqueous ethylation with sodium tetraethylborate. Reverse isotope-dilution analysis was used for quantitation of the spike solutions by means of natural MBT, DBT, and TBT standards. The mixed spikes were used for simultaneous analysis of MBT, DBT and TBT in the certified reference materials, PACS-2, CRM 462, and CRM 646, with satisfactory results. The excellent agreement of the different speciation results obtained by use of the different spikes is a good indicator of the precision, accuracy, and reliability which can be achieved by using isotope-dilution analysis for trace metal speciation.Application of a double spike containing (119)Sn-enriched MBT (79.7 At%), (118)Sn-enriched DBT (86.7 At%), and (119)Sn-enriched TBT (83.1 At%) also enabled evaluation of the conditions resulting in quantitative extraction of the species from the solid matrix, in combination with possible alterations depending on the different extraction procedures used (mechanical shaking, ultrasounds, and microwaves). Mathematical equations used for this purpose computed the correct species concentrations directly and, additionally, the decomposition factors (from TBT to DBT and from DBT to MBT) after precise measurement of the (119)Sn/(120)Sn and (118)Sn/(120)Sn ratios for all butyltin species by GC-ICP-MS.     

Interference from elemental sulphur in the determination of organotins by gas chromatography with flame photometric detection

Elemental sulphur, a common constituent of marine sediments, has been shown to give dialkyl sulphides with the Grignard reagents commonly used to derivatize alkyltin species before their determination by gas chromatography with flame photometric detection (GC–FPD). Further, it has been demonstrated that even with the red filter for 610 nm (normally used for organotin compounds) fitted to the detector, sulphur compounds do give rise to an emission signal, which may be mistaken for tin emission from a pentylated or propylated alkyltin compound, as the respective retention times are in some cases quite close. © 1997 by John Wiley & Sons, Ltd.     

Purge and trap flame photometric gas chromatography technique for the speciation of trace organotin and organosulfur compounds in a human urine standard reference material (SRM)

Ultratrace levels of organotin species and an organosulfur compound were detected in a National Bureau of Standards (NBS) human urine Standard Reference Material, SRM 2670, and a previously certified urine SRM 2672, using a purge and trap system coupled to a gas chromatograph equipped with a flame photometric detector. samples of the SRM were treated with sodium borohydride to form volatile tin hydrides. Species detected included dimethyltin (1.04 ng/ml), butyltin (0.03 ng/ml), and dimethyl-disulfide (2.73 ng/ml) in the new stock of freeze dried human urine SRM 2670 being prepared for issue by NBS and methyltin (1.0 ng/ml), butyltin (1.5 ng/ml), and inorganic tin (28.1 ng/ml) in the old stock of SRM 2672. This analytical technique should have useful applications in studies that are needed to develop a toxicological data base and monitoring programs for human organotin exposure.     

Isotope dilution GC-MS routine method for the determination of butyltin compounds in water

A standard GC-MS instrument with electron impact ionisation has been used to develop a fast, simple and reliable method for the simultaneous determination of monobutyltin (MBT), dibutyltin (DBT) and tributyltin (TBT) in water samples. Isotope dilution analysis (IDA) is used for the determination of species, taking advantage of a commercially available spike solution containing a mixture of MBT, DBT and TBT enriched in ¹¹⁹Sn. Method detection limits for 100-mL samples were between 0.18 and 0.25 ng L⁻¹ for the three butyltin compounds with typical RSD between 2 and 4% at levels between 100 and 10 ng L⁻¹, respectively. Recovery of tin species in spiked samples (natural water, wastewater and seawater) was quantitative. The stability of butyltin compounds in collected seawater samples was also studied. The addition of a 1% (v/v) glacial acetic acid preserved tin species in the samples for at least 5 days at room temperature. The IDA method was finally implemented in a routine testing laboratory and it was subsequently accredited by the Spanish National Accreditation Body according to the requirements of UNE-EN ISO/IEC 17025.     

Development of a continuous flow hydride generation laser-induced breakdown spectroscopic system: Determination of tin in aqueous environments

The design, construction and optimization studies of a continuous flow hydride generation laser-induced breakdown spectroscopic system, HG-LIBS, for the determination of tin in aqueous environments is presented. Optimization of the Laser Induced Breakdown Spectroscopy (LIBS) signal with respect to carrier gas flow rate, analyte, acid (HCl) and reductant (NaBH₄) concentrations and flow rates was performed by using spectral emission intensity from the neutral Sn(I) line at 284.0 nm under atmospheric pressures. With flow rates of 5.0 mL/min for NaBH₄ and 2.5 mL/min for HCl, optimum NaBH₄ and HCl concentrations were determined as 2.0% (w/v) and 1.0% (v/v), respectively. The hydride generation efficiency of the system was tested for tin hydride, stannane (SnH₄), by inductively coupled plasma mass spectrometer (ICP-MS). It was found that higher than 99% of the analyte was released into the gaseous phase. Upon optimization, the minimum detectable Sn concentration was found as 0.3 mg/L in water samples. That corresponds to more than two orders of increase in sensitivity compared to methods that employ common sample introduction techniques in liquids analysis by LIBS. Over 90% recoveries were obtained from spiking experiments with river, tap and drinking water samples. Results illustrate potential use of the continuous flow HG-LIBS system for monitoring of Sn concentrations in aqueous environments.     

水相中丁基锡化合物同时衍生／萃取气相色谱／火焰光度检测方法研究

本文建立了水相中丁基锡化合物的衍生／萃取一步进行气相色谱／火焰光度检测的方法，探讨了溶剂，氮气流速，温度及火焰条件对分离及测定的影响，获得了理想的分离及检测条件。检出限分别为一丁基锡（ＭＢＴ）及二丁基锡（ＤＢＴ）０．２５ｎｇ，三丁基锡（ＴＢＴ）及四丁基锡（Ｂｕ４Ｓｎ）０．５ｎｇ；线性范围０－８ｎｇ，相对标准偏差小于４％。     

Butyltin compounds in vinegar collected in Beijing: Species distribution and source investigation

Forty-eight vinegar samples including white vinegar,rice vinegar and mature vinegar were collected from several markets in Beijing.Butyltin compounds were determined by headspace solid-phase microextraction coupled with gas chromatography and flame photometric detector after in situ ethylation with sodium tetraethylborate.Butyltin species were detected in sixteen vinegar samples and ranged from 0.012 to 14.10 μg Sn L 1.The detection rate of white vinegar is higher than that of rice vinegar and mature vinegar.Vinegar samples with relatively high butyltin concentration(>1.5 μg Sn L 1) were those stored in plastic bags,indicating that the plastic bag was one of the possible sources of butyltin contamination.This was further confirmed by the leaching experiments of three selected plastic bags,and monobutyltin was detected in the leaching solvents.According to the estimation,the average daily intake of total butyltin compounds through vinegar consumption is about 0.04 ng Sn/kg b.w.,much lower than the Tolerable Daily Intake(TDI) of 100 ng Sn/kg b.w.set by the European Food Safety Authority(EFSA).     

Evaluation of different derivatization methods for the multi-element detection of Hg, Pb and Sn compounds by gas chromatography-microwave induced plasma-atomic emission spectrometry in environmental samples

A multi-element, element-specific detector for gas chromatography (GC) based on atomic emission spectroscopy (AES) with a microwave induced plasma (MIP) source was tested on some environmental samples. As derivatization procedure, direct aqueous phase ethylation and chelation/extraction followed by Grignard reaction were tested on the following ions: methylmercury, ethylmercury, phenylmercury, mercury(II), trimethyllead, dimethyllead, lead(II), trimethyltin, dimethyltin, triethyltin, tripropyltin, tributyltin, dibutyltin, butyltin, and tin(IV). For mercury species a direct aqueous phase phenylation was successfully tested. The different methods of derivatization are compared, and the performance (sensitivity, linearity) of the GC-MIP-AES system is discussed. Some examples of application to environmental samples (biological tissues) are given.     

Determination of butyltin species in natural waters using aqueous phase ethylation and off-line room temperature trapping

Monobutyltin (MBT), dibutyltin (DBT) and tributyltin (TBT) were determined in natural water samples by aqueous phase ethylation with sodium tetraethylborate (STEB), room temperature trapping of the resulting volatile derivatives on Tenax TA^®, followed by gas chromatography-quartz furnace atomic absorption spectrometry (GC-QFAAS). Recoveries of butyltin spikes from natural water samples were 90-109% at concentrations of ∼100 ng Sn/l. The method precision at ∼100 ng Sn/l was ≤6% RSD for butyltins spiked into natural waters. The detection limits for 1 l water samples were <1 ng Sn/l for all butyltin species. Sample throughput of the method is high (greater than three samples per hour) due to the two-stage nature of the procedure, which allows derivatisation/trapping and GC-QFAAS quantitation to be performed separately. Off-line trapping is also advantageous as it extends the life of the GC column and quartz furnace to at least 12 months due to minimisation of carry-over of co-purged material.     

"Virtual injector" flow tube method for measuring relative rates kinetics of gas-phase and aerosol species

A new method for measuring gas-phase and aerosol reaction kinetics is described in which the gas flow, itself, acts as a "virtual injector" continuously increasing the contact time in analogy to conventional movable-injector kinetics techniques. In this method a laser is directed down the length of a flow tube, instantly initiating reaction by photodissociation of a precursor species at every point throughout the flow tube. Key tropospheric reactants such as OH, Cl, NO(3), and O(3) can be generated with nearly uniform concentrations along the length of the flow tube in this manner using 355 nm radiation from the third harmonic of a Nd:YAG laser. As the flow travels down the flow tube, both the gas-phase and particle-phase species react with the photogenerated radicals or O(3) for increasingly longer time before exiting and being detected. The advantages of this method are that (1) any wall loss of gas-phase and particle species is automatically accounted for, (2) the reactions are conducted under nearly pseudo-first-order conditions, (3) the progress of the reaction is followed as a continuous function of reaction time instead of reactant concentration, (4) data collection is quick with an entire decay trace being collected in as little as 1 min, (5) relative rates of several species can be measured simultaneously, and (6) bimolecular rate constants at least as small as k = 10(-17) (cm(3)/molecule)/s, or aerosol uptake coefficients at least as small as γ = 10(-4), can be measured. Using the virtual injector technique with an aerosol chemical ionization mass spectrometer (CIMS) as a detector, examples of gas-phase relative rates and uptake by oleic acid particles are given for OH, Cl, NO(3), and O(3) reactions with most agreeing to within 20% of published values, where available.     

Interpretation of butyltin mass spectra using isotope pattern reconstruction for the accurate measurement of isotope ratios from molecular clusters

The fragmentation patterns of butyltin compounds (mono-, di-, and tributyltin) in an electron impact ion source were studied using an isotope pattern reconstruction algorithm with emphasis on isotope ratio measurements from molecular clusters. For this purpose, standards of natural tin isotope abundance and a (119)Sn-enriched mixture of the three compounds were both ethylated and propylated using sodium tetraalkylborates. The corresponding mass spectra of the various tetraalkyltin compounds prepared were obtained by GC/MS after their extraction with hexane.The results showed that pure interference-free molecular clusters were obtained only for certain R(3)Sn(+) ions where no isobaric overlap with R(2)SnH(+) ions occurred (e.g. BuEt(2)Sn(+) overlaps with Bu(2)SnH(+)). These ions are ideal candidates for accurate Sn isotope ratio measurements, while isotope pattern perturbing interferences are observed for other molecular fragments down to Sn(.)(+). Isotope pattern reconstruction algorithm thus can be used as an analytical tool to ensure the absence of molecular interferences--a requirement for accurate isotope ratio measurements from molecular clusters. The relevance of these studies for the determination of butyltin compounds in environmental samples by isotope dilution GC/MS is also discussed.