Simulation of orientation of uniaxially stretched poly(vinyl phenol) by molecular dynamics

Molecular dynamics were performed for the simulation of the uniaxial deformation of poly(vinyl phenol) under periodic boundary conditions with the Parrinello–Rahman scheme followed by relaxation under NVT conditions (constant number of atoms, volume, and temperature). Changes in the orientation of the main chain, benzene segments, and hydrogen bonds were analyzed with the second‐order Legendre polynomial, 〈P₂(cos θ)〉. Conformational changes were also followed. During deformation, backbone and phenyl rings both initially orient parallel to the draw direction. After relaxation, the chain is oriented parallel to the deformation direction, and side groups orient approximately perpendicular to this direction, in agreement with experimental data reported in the literature. Orientation values are higher than experimental values, as expected from the limited relaxation time range attainable in the simulations. Deformation proceeds by changes from gauche conformers to nontrans, nongauche, and trans conformers, whereas relaxation mainly allows high‐energy nontrans, nongauche conformers to convert into lower energy trans conformers. Values of the α angle for ring and bonded O? H segments agree with those in the literature. Differences observed for free hydroxyl moieties are discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1601–1625, 2002     

Effect of inorganic phase on polymeric relaxation dynamics in PMMA/silica hybrids studied by dielectric analysis

Dielectric relaxation spectroscopy was used to investigate the effect of the inorganic phase on the polymeric relaxation dynamics in PMMA/silica hybrids synthesized in situ via sol-gel processes. It was found that the large-scale molecular motions of PMMA were influenced by the addition of silica, inducing longer mean relaxation times, more heterogeneous relaxing environments and the higher activation energy. Explanations based on hydrogen-bond interactions between two phases and a fraction of entrapped chain segments in silica networks were proposed to understand the influence of the silica.     

Morphological evolution and orientation development of stretched iPP films: Influence of draw ratio

Varying the processing conditions of semicrystalline polymers can produce different morphologies of crystallization, which leads to different properties. There have been extensive studies of flow‐induced crystallization on isotactic polypropylene (iPP) using predominantly shear flow. A stretching method, deduced from extrusion, was introduced to study the morphological evolution of elongation‐induced shish‐kebab crystallization. Different morphologies of the resultant samples with different draw ratios (DRs) were carefully investigated and characterized via differential scanning calorimetry, polarizing light microscopy, scanning electron microscopy, atomic force microscopy, and 2D small‐angle X‐ray scattering. In addition, the degree of orientation of the samples with different DRs was also investigated using the 2D wide‐angle X‐ray scattering technique. The results indicate that the elongation‐induced morphology is strongly dependent on the effective stretching flow expressed in terms of the DR, which is defined as the ratio of rates between take‐up and the extrusion. The spherulite is dominant at low DRs, but it starts to deform along the stretching direction with increasing DR. The shish‐kebab structure in the stretched film, composed of stretched chains (shish) and layered crystalline lamellae (kebabs), increases gradually with an increase in the DR, whereas the spherulites gradually decreased. Furthermore, the overall orientation of α‐phase crystals, expressed by the Hermans orientation parameter, is also found to increase dramatically with the DR, and the rate of increase strongly depends on the DR. The different crystal morphologies are attributed to crystallization induced by different elongations of the stretched iPP films. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1223–1234, 2010     

The discovery of isotactic polypropylene and its impact on pure and applied science

This article recalls some aspects of the fascinating history of the discovery by Giulio Natta and his research group of the stereoselective polymerization of propylene and the understanding of the relationships between structure and properties of semicrystalline polymers. The impact of the discovery of isotactic polypropylene and stereoregular polymers on pure and applied science is briefly outlined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 391–395, 2004     

Dielectric and dynamic mechanical relaxation studies on poly(aryl ether ketone)s

The relaxation behavior of four amorphous poly(aryl ether ketone)s was investigated using dielectric relaxation spectroscopy and dynamic mechanical analysis. The temperature dependence of the relaxation times of the glass transition process and the cooperative nature of this process were unaffected by changes in polymer structure. The temperature location of the loss peaks for all polymers progressed smoothly between the low frequency of the mechanical measurements and the higher frequencies of the dielectric probe. Differences were observed in mechanical activation energy and dielectric relaxation strength for one polymer which contained a significant concentration of meta linkages, compared with the para-linked polymers, while relaxation broadness was generally greater in the dynamic mechanical mode. Changes in chemical structure had little effect on the shape, intensity, and location of the β-relaxation peak, the main observation being that the Arrhenius activation energy measured by dynamic mechanical analysis was significantly higher than that calculated from the dielectric data. The dielectric β-relaxation was sensitive to absorbed moisture. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 851–859, 1998     

Anionic lanthanide phenoxide complexes as novel single‐component initiators for the polymerization of ε‐caprolactone and trimethylene carbonate

The anionic lanthanide‐sodium‐2,6‐di‐tert‐butyl‐phenoxide complexes [Ln(OAr)₄][Na(DME)₃]·DME (Ln = Nd 1 (neodymium), Sm 2 (samarium), or Gd 3 (gadolium); DME = dimethoxyethane) were synthesized by the reaction of anhydrous LnCl₃ with 4 equiv of sodium‐2,6‐di‐tert‐butyl‐phenoxide NaOAr in high yields and structurally characterized. These complexes showed high catalytic activity in the ring‐opening polymerizations of ?‐caprolactone (?‐CL) and trimethylene carbonate (TMC). The catalytic activity profoundly depended on the lanthanide metals. The active order of Gd < Sm < Nd for the polymerization of ?‐CL and TMC was observed. The polymers obtained with these initiators all showed a unimodal molecular weight distribution, indicating that the [Ln(OAr)₄][Na(DME)₃]·DME anionic complexes could be used as single‐component initiators. The anionic complex was more efficient than the corresponding neutral complex, Ln(OAr)₃(THF)₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1210–1218, 2007     

Study of hydrogen‐bonding strength in poly(ϵ‐caprolactone) blends by DSC and FTIR

The hydrogen‐bonding strength of poly(?‐caprolactone) (PCL) blends with three different well‐known hydrogen‐bonding donor polymers [i.e., phenolic, poly(vinyl‐phenol) (PVPh), and phenoxy] was investigated with differential scanning calorimetry and Fourier transform infrared spectroscopy. All blends exhibited a single glass‐transition temperature with differential scanning calorimetry, which is characteristic of a miscible system. The strength of interassociation depended on the hydrogen‐bonding donor group in the order phenolic/PCL > PVPh/PCL > phenoxy/PCL, which corresponds to the q value of the Kwei equation. In addition, the interaction energy density parameter calculated from the melting depression of PCL with the Nishi–Wang equation resulted in a similar trend in terms of the hydrogen‐bonding strength. Quantitative analyses on the fraction of hydrogen‐bonded carbonyl groups in the molten state were made with Fourier transform infrared spectroscopy for all systems, and good correlations between thermal behaviors and infrared results were observed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1348–1359, 2001     

Synthesis of degradable crosslinked polymers based on 1,5-dioxepan-2-one and crosslinker of bis-ϵ-caprolactone type

Poly(lactones) may be crosslinked by ring-opening polymerization of the corresponding cyclic esters in the presence of tetrafunctional bis(ϵ-caprolactone). The homopolymer of 1.5-dioxepan-2-one (DXO) has poor mechanical properties but also some very good properties, such as biocompatibility and degradability. Crosslinking of degradable polymer based on the poly(ether-ester) DXO was performed with crosslinkers having the same reactivity as the monomer. 2,2-Bis(ϵ-caprolactone-4-yl)propane (BCP) and bis(ϵ-caprolactone-4-yl) (BCY) with tetrafunctionalities were synthesized from the corresponding diols and then used as comonomers during the polymerization of DXO. The comonomers showed the same reactivity to the initiator, stanneous 2-ethylhexanoic acid, as DXO and perfectly random crosslinked films were obtained. The crosslinked films showed a high degree of swelling already at 2–3 mol % BCP or BCY. The BCP crosslinker was somewhat less soluble in DXO at lower temperatures, but all BCP was soluble at 180°C. These polymeric films were elastic with no crystallinity and the T_g values increased from −39°C for pure DXO to −35°C for BCP crosslinked films and −21°C for BCY crosslinked ones. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1635–1649, 1997     

Poly(vinyl chloride)‐based miscible blends: Changes induced in the structural characteristics and in dielectric α relaxation of pure poly(vinyl chloride)

In this work we investigate by means of dielectric relaxation spectroscopy how segmental motions occurring in poly(vinyl chloride) (PVC) are modified by blending of PVC with small amounts of two different homopolymers: crystalline poly(ϵ‐caprolactone) (PCL) and glassy syndiotactic poly(methylmethacrylate) (sPMMA). The dynamics of the α relaxation of PVC is severely changed by blending it with PCL or sPMMA becoming faster or slower, respectively. Simultaneously, the shape of the relaxation function is being importantly altered. It shows a stronger non‐Debye character being broader and strongly temperature‐dependent. This fact leads us to calculate distributions of relaxation times for the blends that are wider in comparison to the one obtained for pure PVC. Complementary X‐ray diffraction measurements have been performed in order to assure the absence of crystallinity in the blends, and some small variations can be deduced at the level of interchain structural correlations of PVC. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 234–247, 2000     

Effect of temperature and solvent on polymer tacticity in the free‐radical polymerization of styrene and methyl methacrylate

The effect of temperature and solvent on polymer tacticity in free‐radical polymerization of styrene and methyl methacrylate was studied by ¹³C and ¹H NMR, respectively. Polystyrene shows a mild syndiotactic tendency (P_m = 0.36 ± 0.02) that is independent of temperature over a wide range (?10 to 120 °C), while poly(methyl methacrylate) shows a stronger syndiotactic tendency (P_m = 0.17 ± 0.01 at 30 °C) that decreases as temperature is increased (P_m = 0.22 ± 0.02 at 80 °C). None of the polymerization solvents studied (bulk, THF, DMF, DMSO, acetonitrile, and acetone) had a significant effect on polymer tacticity in either system. The triad fractions of both polymers showed deviations from the Bernoulli model, implying that the antepenultimate unit affects the propagation reaction. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3351–3358     

Block–Stereoblock Copolymers of Poly(ϵ‐Caprolactone) and Poly(Lactic Acid)

A magnesium complex of the type {ONNN}Mg‐HMDS wherein {ONNN} is a sequential tetradentate monoanionic ligand is introduced. In the presence of an alcohol initiator this complex catalyzes the living and immortal homopolymerization of the lactide enantiomers and ?‐caprolactone at room‐temperature with exceptionally high activities, as well as the precise block copolymerization of these monomers in a one‐pot synthesis by sequential monomer addition. Copolymers of unprecedented microstructures such as the PCL‐b‐PLLA‐b‐PDLA and PDLA‐b‐PLLA‐b‐PCL‐b‐PLLA‐b‐PDLA block–stereoblock microstructures that feature unique thermal properties are readily accessed.     

Enthalpy relaxation in polymethyl(α-n-alkyl)acrylates: Effect of length of alkyl chain

In this work, we have investigated by DSC the structural relaxation of amorphous polymethyl(α-n-alkyl)acrylates in which it is possible to change the length of the alkyl chain. We have evaluated the Narayanaswamy parameter, x, which controls the relative contribution of temperature and of structure to the relaxation time, the apparent activation energy, Δh*, and the nonexponentiality parameter, β, of the stretched exponential response function. The results suggest that x increases while Δh* decreases and β remains constant as the length of the side chain increases. This allows us to comment on the effect of chemical modification on the relaxation kinetics. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 583–593, 1998     

Synthesis and characterization of poly(ϵ-caprolactone)-poly(ethylene glycol) block copolymer

Poly(ϵ-caprolactone)–poly(ethylene glycol)–poly(ϵ-caprolactone) triblock copolymers (PECL) covering a wide range of poly(ethylene glycol) (PEG) lengths were synthesized with alkali metal alkoxide derivatives of poly(ethylene glycol). The effects of various factors, such as amount of the initiator, reaction time and temperature, polarity of solvent, length of PEG segment, and counterion on the polymerization were investigated. The copolymers were characterized by ¹H-NMR, IR, GPC, and DSC. It was found that THF system is superior to toluene system. The conversion of the monomer increased with increase of the initiator concentration. High molecular weight of the copolymer and high conversion of the monomer was obtained at below 30°C within 5 min. The polymerization process was studied by GPC and the coexistence of propagation and transesterification reaction was found, which leaded to relatively broad molecular weight distribution of the copolymers. © 1997 John Wiley & Sons, Inc.     

A rheological,optical, and x-ray study of the relaxation of orientation of nematic PBZT

The ultimate properties of liquid crystalline polymers depend upon the achievement of high orientation, usually by means of flow fields. The properties are limited by disorientation which can occur before the product is solidified. Such cooperative orientation and disorientation phenomena also underlie the complex fluid rheology and product microstructure of these materials. The orientation and subsequent disorientation can be followed dynamically by optical and x-ray techniques. Normally, monitoring of orientation is possible only by “fast” techniqes, such as birefringence, these are not applicable to opaque and strongly scattering liquid-crystalline systems. To enable examination of the full dynamic response of concentrated nematic solutions of poly(1,4-phenylene-2,6 benzobisthiazole) (PBZT) the Daresbury Synchrotron Radiation Source was used. PBZT is among the most rigid macromolecules and serves as a good model for other materials of its class. The orientation process determined optically and from x-rays is correlated with fluid rheology and availabel theoretical approaches. During relaxation from near perfect mesogen alignment three principal stages of the disorientation process were identified corresponding to solvent disorientation (first stage of stress relaxation), banding (slow stress relaxation and mesogen disorientation), and finally a very slow banding to polydomain transition. © 1993 John Wiley & Sons, Inc.     

Temperature dependence of molecular conformation in uniaxially deformed isotactic polypropylene investigated by combination of polarized FTIR spectroscopy and 2D correlation analysis

Evolution of molecular conformation in uniaxially deformed isotactic polypropylene (iPP) as a function of temperature is investigated by time‐resolved polarized Fourier‐transform infrared spectroscopy. It is observed that oriented crystals (microfibrils) induced by deformation possess better thermal stability compared with isotropic spherulites. 2D correlation analysis reveals that the relaxation process of ordered helices in deformed iPP could be divided into two regions referring to the melting of different crystalline structures. No obvious sequential change of ordering conformations observed in low temperature region is attributed to melting of defective or destructed crystals. However, notable sequential changes of helices occur in the high temperature region; interestingly, long helices are more thermally stable than short helices. The central region of microfibrils is suggested to consist of a large amount of long helical bundles, and the short ordering segments are primarily located in the outer lateral surfaces. A physical picture of the conformational distribution in deformation‐induced microfibrils is thus gained. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 673–684     

Synthesis and characterization of a novel biodegradable,thermoplastic polyurethane elastomer

A series of biodegradable, thermoplastic polyurethane elastomers poly(?‐caprolactone‐co‐lactide(polyurethane [PCLA–PU] were synthesized from a random copolymer of L ‐lactide (LA) and ?‐caprolactone (CL), hexamethylene diisocyanate, and 1,4‐butanediol. The effects of the LA/CL monomer ratio and hard‐segment content on the thermal and mechanical properties of PCLA–PUs were investigated. Gel permeation chromatography, IR, ¹³C NMR, and X‐ray diffraction were used to confirm the formation and structure of PCLA–PUs. Through differential scanning calorimetry, tensile testing, and tensile‐recovery testing, their thermal and mechanical properties were characterized. Their glass‐transition temperatures were below ?8 °C, and their soft domains became amorphous as the LA content increased. They displayed excellent mechanical properties, such as a tensile strength as high as 38 MPa, a tensile modulus as low as 10 MPa, and an elongation at break of 1300%. Therefore, they could find applications in biomedical fields, such as soft‐tissue engineering and artificial skin. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5505–5512, 2006     

Hydrolyzable poly(ester-urethane) networks from L-lysine diisocyanate and D,L-lactide/ϵ-caprolactone homo- and copolyester triols

Bioabsorbable poly(ester-urethane) networks were synthesized from ethyl 2,6-diisocyanatohexanoate (L -lysine diisocyanate) (LDI) and a series of polyester triols. LDI was synthesized by refluxing L-lysine monohydrochloride with ethanol to form the ester, which was subsequently refluxed with 1,1,1,3,3,3-hexamethyldisilazane to yield a silazane-protected intermediate. This product was then phosgenated using triphosgene. Polyester triols were synthesized from D,L-lactide, ?-caprolactone, or comonomer mixtures thereof, using glycerol as initiator and stannous octoate as catalyst. Polyurethane networks were cured using [NCO]/[OH] = 1.05 and stannous octoate (0.05 wt %) for 24 h at room temperature and pressure and 24 h at 50°C and 0.1 mm Hg. LDI-based polyurethane networks were totally amorphous and possessed very low sol contents. Networks based on poly (D,L-lactide) triols were rigid (T_g ∽ 60°C) with ultimate tensile strengths of ～ 40–70 MPa, tensile moduli of ～ 1.2–2.0 GPa, and ultimate elongations of ～ 4–10%. Networks based on ?-caprolactone triols were low-modulus elastomers with tensile strengths and moduli of ～ 1–4 MPa and ～ 3–6 GPa, respectively, and ultimate elongations of ～ 50–300%. Networks based on copolymers displayed physical properties consistent with monomer composition and were tougher than the networks based on the homopolymers. Tensile strengths for the copolymers were ～ 3–25 MPa with ultimate elongations up to 600%. Hydrolytic degradation under simulated physiological conditions showed that D ,L -lactide homopolymer networks were the most resistant to degradation, undergoing virtually no change in mass or physical properties for 60 days. ?-Caprolactone-based networks were resistant to degradation for 40 days, and high-lactide copolymer-based networks suffered substantial losses in physical properties after only 3 days. © 1994 John Wiley & Sons, Inc.     

Intramolecular interactions in poly(styrene-co-acrylonitrile)/poly(ε-caprolactone) blends

Specific interactions in blends of poly(ε-caprolactone) (PCL) and poly(styrene-co-acry-lonitrile) (SAN) were studied as a function of copolymer composition and blend ratio by using Fourier-transform infrared spectroscopy (FTIR). It was shown that miscibility occurred within a certain range of copolymer compositions because the presence of PCL reduced the thermodynamically unfavorable repulsion between styrene and acrylonitrile segments in the random copolymer. This effect was observed in terms of a shift to higher frequencies in the 700 cm^-1 γ-CH out-of-plane deformation vibration absorption of styrene and in the approximately 2236 cm^?1 C?N stretching frequency band in acrylonitrile segments. Specific intermolecular interactions between SAN and PCL were not observed in this study. © 1993 John Wiley & Sons, Inc.     

Synthesis and characterization of biodegradable block copolymers of ϵ-caprolactone and D,L-lactide initiated by potassium poly(ethylene glycol)ate

Poly(D ,L -lactide)–poly(ϵ-caprolactone)–poly(ethylene glycol)–poly(ϵ-caprolactone)–poly(D ,L -lactide) block copolymer (PLA–PCL–PEG–PCL–PLA) was prepared by copolymerization of ϵ-caprolactone (ϵ-CL) and D ,L -lactide (D ,L -LA) initiated by potassium poly(ethylene glycol)ate in THF at 25°C. The copolymers with different composition were synthesized by adjusting the mole ratio of reaction mixture. The resulted copolymers were characterized by ¹H-NMR, ¹³C-NMR, IR, DSC, and GPC. Efforts to prepare copolymers with the corresponding structure of PCL–PLA–PEG–PLA–PCL and D ,L -lactide/ϵ-caprolactone random copolymers were not successful. © 1997 John Wiley & Sons, Inc.