Studies on thermotropic liquid crystalline polyurethanes. II. Synthesis and properties of liquid crystalline polyurethane elastomers

Three series of novel thermotropic liquid crystalline polyurethane elastomers (TLCPUEs) were studied. Hard segments were formed by using hexamethylene diisocyanate (HDI) reacted with a mesogenic unit, benzene-1,4-di(4-iminophenoxy-n-hexanol), which also acted as a chain extender. Three diols: 1,10-decanediol,poly(oxytetramethylene) glycol (PTMEG) M _n = 1000 and PTMEG M _n = 2000 were used as the soft segments. The effects of soft segments of polyurethanes on the liquid crystalline behavior were studied. Higher molecular weight TLCPUEs were obtained by adding 30?50 mol % of mesogenic segments to diisocyanates. In contrast to a conventional chain extender such as 1,2-ethylene glycol or 1,4-butyl glycol, the synthesized polyurethane elastomers exhibited a mesophase transition by using a mesogenic unit as the chain extender. Mesophase was found for all synthesized LC polyurethanes except of polymers H2-A-12 and H2-A-7. The structures and the thermal properties of all synthesized TLCPUEs were studied by using FTIR spectroscopy, wide-angle x-ray diffraction (WAXD) and DSC measurements, a polarizing microscope equipped with a heating stage, dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA). Mechanical properties were also examined by using a tensilemeter. © 1995 John Wiley & Sons, Inc.     

Structure analysis of polyether-based thermoplastic polyurethane elastomers by FTIR, 1H NMR and 13C NMR

One kind of unknown structure sequence and composition ratio of thermoplastic polyurethane elastomers were characterized by nuclear magnetic resonance spectroscopy, Fourier transformed infrared spectroscopy, and gel permeation chromatography (GPC). The results showed that the polyurethane (PU) was obtained from poly(tetramethylene glycol) (PTMG) as soft segment, 1,4-butanediol (BDO) as chain extender, and 4,4′-methylenediphenyl diisocyanate (MDI) as hard segment. Furthermore, the composition ratio of MDI:PTMG:BDO was 2.07:1.22:1.00. At last, the molecular weight of PU was determined by GPC, and the number average molecular weight (M_n) and weight average molecular weight (M_w) are 63,300 and 133,800?g?mol^?1, respectively.     

Coupling and Cyclization of Sydnone Compounds

Cyclization were occurred via the coupling reactions of some mercuric chloride derivatives of sydnone with LiPdCl₃-CuCl₂. A unique six-membered ring, 3,3′-ethylene-4,4′-bissydnone, was obtained by the cyclization reation of 1,2-di[3-(4-chloromercuric)sydnonyl]ethane. However, the seven-membered 3,3′-trimethylene-4,4′-bissydnone and 1,3-di[3-(4-chloro)sydnonyl]-propane were obtained from the corresponding mercuric chlroide of sydnone. Onyl substitution reaction took place when 4,4′-di[3-(4-chloromercuric)sydnonyl]biphenyl, 4,4′-di[3-(4-chloromercuric)sydnonyl]benzene, di(p-[3-(4-chloromercuric)sydnonyl]-phenyl}methane and, di(p-[3-(4-chloromercuric)sydnonyl]phenyl]ether were treated using the same process.     

Segmented polyurethanes with 4,4′-bis-(6-hydroxyhexoxy)biphenyl as chain extender. Part 2. Synthesis and properties of MDI-polyurethanes in comparison with 2,4-TDI-polyurethanes

Linear segmented polyurethanes based on poly(butylene adipate)s (PBA) of different molecular weight (M_n 2000, 1000, and 600), 4,4′-diphenylmethane diisocyanate (MDI) and the mesogenic diol 4,4′-bis-(6-hydroxyhexoxy)biphenyl (BHHBP) as well as the unsegmented polyurethane consisting of MDI/BHHBP units have been synthesized and characterized by elemental analysis, ¹³C-NMR and SEC. The thermal behavior and the morphology were studied by DSC, polarizing microscopy, and DMA. The properties of the MDI-polyurethanes were discussed in relation to the BHHBP chain extended 2,4-TDI-polyurethanes and common 1,4-butanediol chain-extended MDI products. MDI polyurethanes based on PBA (M_n 2000) exhibit a glass transition temperature T_g of about −40°C independent of the hard segment content up to ∼50% hard segments. At higher hard segment contents increasing T_gs were observed. Polyurethanes, based on the shorter polyester soft segments PBA (M_n 1000 or 600), reveal an increase in the glass transition temperatures with growing hard segment content. The thermal transitions caused by melting of the MDI/BHHBP hard segment domains are found at 50 K higher temperatures in comparison with the analogous TDI products with mesogenic BHHBP/TDI hard segments. Shortening of the PBA chain length causes a shift of the thermal transitions to lower temperatures. Polarizing microscopy experiments indicate that liquid crystalline behavior is influenced by both the content of mesogenic hard segments and the chain length of the polyester. © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of aromatic polythiazole-amides from new aromatic diamines containing phenyl-pendant thiazole units

New aromatic diamines containing phenyl-pendant thiazole units were synthesized in three steps starting from p-nitrobenzyl phenyl ketone. Novel aromatic polyamides containing phenyl-pendant thiazole units were prepared by the low-temperature solution polyconden-sation of 1,4- (or 1.3-) bis[5-(p-aminophenyl)-4-phenyl-2-thiazolyl] benzene with various aromatic dicarboxylic acid chlorides in N,N-dimethylacetamide. High molecular weight polyamides having inherent viscosities of 0.5–3.0 dL/g were obtained quantitatively. The polythiazole-amides with m-phenylene, 4,4′-oxydiphenylene, and 4,4′-sulfonyldiphenylene units were soluble in N-methyl-2-pyrrolidone, N,N-dimethylacetamide, and pyridine, and gave transparent flexible films by casting from the solutions. These organic solvent-soluble polyamides displayed prominent glass transition temperatures (T_g) between 257 and 325°C. On the other hand, the polythiazole-amides with p-phenylene and 4,4′-biphenylene units were insoluble in most organic solvents, and had no observed T_g. All the polythiazole-amides started to decompose at about 400°C with 10% weight loss being recorded at 450–525°C in air. © 1995 John Wiley & Sons, Inc.     

Synthesis of polyesters by the polyaddition of bis(oxetane)s with active di(ester)s

The polyaddition of bis(oxetane)s 1,4‐bis[(3‐ethyl‐3‐oxetanylmethoxymethyl)]benzene (BEOB), 4,4′‐bis[(3‐ethyl‐3‐oxetanyl)methoxy]benzene (4,4′‐BEOBP), 1,4‐bis[(3‐ethy‐3‐oxetanyl)methoxy] ‐benzene (1,4‐BEOMB), 1,2‐bis[(3‐ethyl‐3‐oxetanyl)methoxy]benzene (1,2‐BEOMB), 4,4‐bis[(3‐ethyl‐3‐oxetanyl)methoxy]biphenyl (4,4′‐BEOMB), 3,3′,5,5′‐tetramethyl‐[4,4′‐bis(3‐ethyl‐3‐oxetanyl)methoxy]biphenyl (TM‐BEOBP) with active diesters di‐s‐phenylthioterephthalate (PTTP), di‐s‐phenylthioisoterephthalate (PTIP), 4,4′‐di(p‐nitrophenyl)terephthalate (NPTP), 4,4′‐di(p‐nitrophenyl)isoterephthalate (NPIP) were carried out in the presence of tetraphenylphosphonium chloride (TPPC) as a catalyst in NMP for 24 h, affording corresponding polyesters with M_n's in the range 2200–18,200 in 41–98% yields. The obtained polymers would soluble in common organic solvents and had high thermal stabilities. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1528–1536, 2004     

Thermotropic polyesters with main chain isomeric naphthylene,trans-1,4-cyclohexylene,and 2,5-pyridinediyl units: The importance of the order of ester linkages in the mesogenic units

Two new series of thermotropic polyesters were prepared and their mesomorphic properties were investigated. The polymers consist of triad aromatic ester-type mesogenic units with decamethylene spacers. The mesogenic units of the first series are composed of isomeric dihydroxynaphthalene moieties as the central structure flanked by two p-oxybenzoyl groups. In the second series the mesogenic units were of reversed ester linkages: the central moieties, derived from 1,4-naphthalene dicarboxylic acid, trans-1,4-cyclohexanedicarboxylic acid, or 2,5-pyridinedicarboxylic acid, are connected on both sides to p-phenylene structures. Two low molecular weight model compounds with 1,4-naphthylene unit at the center of the mesogenic unit were synthesized and their mesomorphic properties were compared with those of corresponding polymers. It was observed both for the model compounds and the polymers containing 1,4-naphthylene units that the linking order of the ester group in the mesogenic unit exerted a decisive influence on the capability for the formation of a mesophase. Thermal and mesomorphic properties were investigated by DSC, on a polarizing microscope equipped with a hot-stage, and by visual observation of stir-opalescence of the melts.     

Synthesis of several series of liquid crystalline polyaroyl-bis-oxyarylates and their structure-property relationships

Abstract

Several series of liquid crystalline polyaroyl-bis-oxyarylates containing 1,4-phenylene, 4,4′-biphenylene and 2,6-naphthylene units have been synthesized with the use of aroyl-bis-oxyaroyl dichlorides. Melting and clearing temperatures of every polymer under investigation were compared with those of corresponding polyterephthaloyl-bis-4-oxybenzoates.     

Synthesis and properties of segmented main‐chain liquid‐crystalline polyurethanes with a high aspect ratio mesogenic diol as a chain extender

Main‐chain liquid‐crystalline polyurethanes were synthesized based on a high aspect ratio mesogenic diol (4‐{[4‐(6‐hydroxyhexyloxy)‐phenylimino]‐methyl}‐benzoic acid 4‐{[4‐(6‐hydroxyhexyloxy)‐phenylimino]‐methyl}‐phenyl ester) as a chain extender; polycaprolactone (PCL) diol soft segments of different number‐average molecular weights (530, 1250, or 2000); and different diisocyanates, including 1,4‐hexamethylene diisocyanate (HMDI), 4,4′‐methylene bis(cyclohexyl isocyanate) (H₁₂MDI), and 4,4′‐methylene bis(phenyl isocyanate) (MDI). The structure of the polymers was confirmed with Fourier transform infrared spectroscopy, and differential scanning calorimetry and polarizing microscopy measurements were carried out to examine the liquid‐crystalline and thermal properties of the polyurethanes, respectively. The mesogenic diol was partially replaced with 20–50 mol % PCL. A 20 mol % mesogen content was sufficient to impart a liquid crystalline property to all the polymers. The partial replacement of the mesogenic diol with PCL of various molecular weights, as well as the various diisocyanates, influenced the phase transitions and the occurrence of mesophase textures. Characteristic liquid‐crystalline textures were observed when a sufficient content of the mesogenic diol was present. Depending on the flexible spacer length and the mesogenic content, grained and threadlike textures were obtained for the HMDI and H₁₂MDI series polymers, whereas the polyurethanes prepared from MDI showed only grained textures for all the compositions. The polymers formed brittle films and could not be subjected to tensile tests. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1527–1538, 2002     

Hydrolysis of aromatic polyurethane in water under high pressure of CO2

We have demonstrated a hydrolysis reaction of polyurethane (PU) under high pressure of carbon dioxide (CO₂) in water. We employed the PU sample, poly(methylene bis‐(1,4‐phenylene)hexamethylene dicarbamate), denoted as M‐PU, which was synthesized from 4,4′‐diphenyl methane diisocyanate and 1,4‐butane diol (BD). The optimum hydrolysis reaction condition was 190 °C under CO₂ pressures over 4.1 MPa in water medium, and 93% hydrolysis of M‐PU was achieved. After the reaction, the water‐soluble parts were obtained, and isolated by column chromatography. The isolated products were 4,4′‐methylenedianiline (MDA) and 1,4‐butane diol (BD), which were components of repeating unit of M‐PU. In addition, the hydrolysis reaction gave no byproduct. This hydrolysis under high pressure of CO₂ with water is a reaction by which M‐PU is selectively hydrolyzed into MDA and BD by cleaving urethane linkage. Moreover, the resulting hydrolyzed products were easily obtained by evaporation of aqueous layer after the reaction, indicating an efficient chemical recycling of PU was achieved. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2004–2010     

Synthesis and comparative study on polyetherimides from isomeric 4,4′-isopropylidenediphenoxy bis(phthalic anhydride)s

Two isomers of commercial 4,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (4,4′-BPADA), that is, 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,4′-BPADA) and 3,3′-(4,4′-isopropylidenediphenoxy) bis(phthalic anhydride) (3,3′-BPADA), were synthesized through aromatic nucleophilic substitution from nitrophthalonitrile and bisphenol A. 3,4′-BPADA was first synthesized from two intermediates, that is, 3-(4-[4-hydroxyphenylisopropylidene] phenoxy) phthalonitrile (3-BPADN) and 3,4′-(4,4′-isopropylidenediphenoxy) bis(phthalonitrile) (3,4′-BPATN). The corresponding three series of polyetherimides (PEIs) were prepared with two representative aromatic diamines (4,4′-oxydianiline and m-phenylenediamine (m-PDA)) via two-step procedure and chemical imidization. Isomeric polyimides showed T_gs from 206 to 256°C in nitrogen and T_d5%s from 488 to 511°C in argon, good mechanical properties (tensile moduli of 2.3–3.3 GPa, tensile strengths of 70–96 MPa, and elongations at break of 3.2%–5.1%), and good solubility. With the introduction of 3-substituted phthalimide unit, PEIs displayed higher T_g values, lower strengths and elongations, better solubility and larger d-spacings. The rheological properties of thermoplastic polyimide resins based on the BPADA isomers were investigated, which showed that polyetherimide PEI-3b derived from 3,3′-BPADA and m-PDA had the lowest melt viscosity among the isomers, indicating that the melt processibility had been greatly improved.     

Properties of Polyurethanes Based on Mesogenic Diol and 4,4'-methylenebis(cyclohexyl Isocyanate)

New polyurethanes with mesogenic units in the main chain due to the use of a liquid crystalline chain extender were synthesized from 4,4'-methylenebis(cyclohexyl isocyanate) (HMDI)using diisocyanates of different trans, trans isomer content, a low molecular diol4,4'-bis(6-hydroxyhexoxy)biphenyl (BHHBP) and a high molecular poly(hexyleneadipate)diol (PHA). The growth of trans, trans isomer content in HMDI used to syntheses of PU induces monotonic growth of melting point, rectilinear growth of crystallization temperatures and the growth of crystallization enthalpy, both for hard segment polyurethanes and block polyurethanes. The increase of trans, trans isomer content in HMDI increases also glass transition temperatures and dynamic storage modulus of the polyurethanes. This revised version was published online in August 2006 with corrections to the Cover Date.     

Two Zn(II) coordination polymers constructed by a new tricarboxylate and different N-containing ligands: synthesis,crystal structures,and selective luminescence sensing for Fe3+ in aqueous solution

Two Zn(II) coordination polymers, {[Zn₃(L)₂(bipy)₂(H₂O)₄}_n (1) and {[Zn(HL)(4,4′-bibp)}_n (2), were obtained from Zn(II) nitrate, a tricarboxylate ligand (H₃L) and different N-containing ligands with hydrothermal conditions, where H₃L = 4-((6-carboxynaphthalen-2-yl)oxy)phthalic acid, bipy = 4,4′-bipyridine, and 4,4′-bibp = 4,4′-di(1H-imidazol-1-yl)-1,1′-biphenyl. Single-crystal X-ray analysis reveals that 1 has a 2-D layer framework formed by L^3? and bipy and 2 has an infinite 1-D structure with Zn₂ units built by 4,4′-bibp ligands. The phase purity, IR spectra, thermal stabilities, and fluorescence properties in the solid state of 1 and 2 were investigated. Moreover, 1 and 2 were chosen as fluorescent probes to sense different metal ions, showing selective response to Fe³⁺ ion through luminescence quenching. The possible sensing mechanism to Fe³⁺ ion is also discussed.     

Effect of Soft Segment Molecular Weight and 3-Methyl Side Group on Microstructural Separation in Polyurethane Elastomers

Abstract

The object of this study was to assess the effect of the chain length and of the pendant 3-methyl side group in the soft segment of polyurethane (PU) elastomers. In addition, the effect of annealing-quenching on the degree of microstructural segregation between the hard and soft segments was also investigated. The study employed electron spin resonance (ESR), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). Samples for ESR measurements were spin-labeled with the nitroxide probe, 4-hydroxy-2,2′,6,6′-piperidine-1-oxyl (TEMPOL), by reaction of an isocyanate group with the hydroxyl group of TEMPOL. The nitroxide label is therefore located at a chain end. The PU's were based on 4,4′-diphenylmethane diisocyanate (MDI), poly(oxytetramethylene) glycols (PTMO), and hydroxyl-terminated random copolymers of tetrahydrofuran and 3-methyl-tetrahydrofuran (THF/Me-THF). Purified 1,4-butanediol (BD) was used as a chain extender. The elastomers made from higher molecular weight (MW) soft segments have better phase segregation than their lower MW counterparts. The 3-methyl side groups on the PTMO backbone have some effect on the arrangements of the two domains. ESR analysis indicated that the increase in the MW of THF/Me-THF decreased the degree of mixing between the hard and soft segments. In PU elastomers made from high MW soft segments, the presence of crystallinity was observed from the DSC measurements. The crystallinity of the soft segments was disrupted by the existence of the 3-methyl side groups.     

Preparation and properties of polyesters from diphenylmethane-4,4′-di(methylthiopropionic acid) and aliphatic diols

The new linear polyesters containing sulfur in the main chain were obtained by melt polycondensation of diphenylmethane-4,4′-di(methylthiopropionic acid) with ethanediol, 1,3-propanediol, 1,4-butanediol, 1,5-pentanediol, 1,6-hexanediol, 1,2-propanediol, 1,3-butanediol, and 2,2′-oxydiethanol. Low-molecular weights, low-softening temperatures and, very good solubility in organic solvents are their characteristics. The structure of all polyesters was determined by elemental analysis, FT-IR and ¹H-NMR spectroscopy, and x-ray diffraction analysis. The thermal behavior of these polymers was examined by differential thermal analysis (DTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The kinetics of polyesters formation by uncatalyzed melt polycondensation was studied in a model system: diphenylmethane-4,4′-di(methylthiopropionic acid) and 1,4-butanediol or 2,2′-oxydiethanol at 150, 160, and 170°C. Reaction rate constants (k₃) and activation parameters (ΔG^≠, ΔH^≠, ΔS^≠) from carboxyl group loss were determined using classical kinetic methods. © 1997 John Wiley & Sons, Inc.     

Synthesis and characterization of segmented liquid crystal poly(azoxy polyester-co-polyoxypropylene)

In this study a series of a segmented copolyester, poly(4,4′-dioxy-2,2′-dimethyl-azoxybenzene dodecanedioyl) (PMABD)-co-polyoxypropylene 400 (POP), was prepared. The chain length of PMABD studied (n) was varied from 7.8-18.2, and that of POP was unchanged. The intrinsic viscosity of the segmented copolyesters was 1.04-1.30, and the number average molecular weight obtained was 2.53 × 10⁴?3.49 × 10⁴ g/mol. The mesophase texture and thermal properties of the segmented copolyesters were measured as functions of n. It was found that the insert of flexible POP between those liquid crystalline domains of PMABD did affect thermotropic properties of PMABD. As the n value was 9.0 and 7.8 (or 7.4 and 8.6% by weight POP) the texture appeared as cholesteric-like oily streaks. The effect could not be attained by simply copolymerizing a mesogenic moiety with a pair of spacers of different lengths. The fluidity and domain structure of the flexible dodecanedioyl-POP-dodcanedioyl segments are taken into account for the obtained results. © 1995 John Wiley & Sons, Inc.     

Thermotropic liquid‐crystalline polymers containing five‐membered heterocyclic groups. X. Relationships between structures of semirigid polyesters based on three disubstituted 2,5‐diphenyl‐1,3,4‐thiadiazoles and thermotropic liquid‐crystalline and optical properties

Thermotropic liquid‐crystalline (LC) semirigid polyesters based on three terphenyl analogues of 1,3,4‐thiadiazole (2,5‐diphenyl‐1,3,4‐thiadiazole)s (DPTD) linking undecamethyleneoxy chain at different substituted positions were synthesized from three disubstituted (4,4′‐, 3,4′‐, and 3,3′‐) dioxydiundecanols of DPTD and four diesters, and the relationships between polymer structures and LC and optical properties were investigated. DSC measurements, texture observations, and wide‐angle X‐ray analyses revealed that the polymers composed of DPTD moiety having a more linear molecular structure and 1,4‐phenylene unit or short aliphatic chain tend to exhibit LC smectic C and/or A phases. The following observations were made: (1) the emergence of smectic C and/or A phases in all the polymers on the basis of 4,4′‐disubstituted DPTD, (2) formation of enantiotropic smectic C and/or A phases in the polymers containing a 1,4‐phenylene unit in the main chain, (3) formation of a more stable smectic C phase in the polymers having a short aliphatic [(CH₂)₄] chain, and (4) a decrease of the mesomorphic property of the polyesters in the order of 4,4′‐DPTD > 3,4′‐DPTD > 3,3′‐DPTD. Solution and solid‐state ultraviolet–visible and photoluminescent spectra indicated that all the polyesters display maximum absorbances and blue emissions arising from the DPTD moiety, whose peak maxima were shifted to lower wavelengths in the order of 4,4′‐DPTD > 3,4′‐DPTD > 3,3′‐DPTD as well as the aforementioned LC property. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2676–2687, 2003     

Liquid crystalline polymers XII. Main chain thermotropic poly(arylidene-ether)s containing 4-tertiary-butyl-cyclohexanone moiety linked with polymethylene spacers

A new homologous series of thermally stable thermotropic liquid crystalline poly(arylidene-ether)s based on 4-tertiary-butyl-cyclohexanone moiety was synthesised by solution polycondensation of 4,4′-diformyl-α,ω-diphenoxyalkanes, I_a–f, or 4,4′-diformyl-2,2′-dimethoxy-α,ω-diphenoxyalkanes, II_a–f, with the 4-tertiary-butyl-cyclohexanone monomer. A model compound III was synthesised from the monomer with benzaldehyde and characterised by elemental and spectral analyses. The inherent viscosities of the resulting polymers were in the range of 0.18–0.92 dL/g. The mesomorphic properties of these polymers were studied as a function of the diphenoxyalkane space length. Their thermotropic liquid crystalline properties were examined by differential scanning calorimetry (DSC) and optical polarising microscopy and demonstrated that the resulting polymers form nematic mesophases over wide temperature ranges. The thermal properties of those polymers were evaluated by thermogravimetric analysis and DSC measurements and correlated to their structural units. X-ray analysis showed that polymers having some degree of crystallinity in the region 2θ = 5–60°. In addition, the morphological properties of selected examples were tested by scanning electron microscopy.     

Non-equilibrium thermal behaviour of a main chain thermotropic polymer

Abstract

The effect of thermal treatment on the thermodynamic properties and structure of a nematic thermotropic main chain polymer with mesogenic groups containing 3,3′-biphenylene units and octamethylene flexible spacers (BF8) has been studied by DSC and X-ray scattering. We have found that BF8 samples do not crystallize even on very slow cooling from the isotropic state, and possessed a glassy nematic structure at room temperature. The strong influence of the cooling rate on both the enthalpy of the nematic-isotropic transition and the rise of specific heat at the glass transition for BF8 samples was observed. It was attempted to explain this result in terms of the improvement of the nematic structure during cooling.     

Substrate-induced adjustment of “slipped” π–π stacking: en route to obtain 1D sandwich chain and higher order self-assembly supramolecular structures in solid state

‘Slipped’ π?π stacking between flexible macrocycle 1⁴⁺ (cyclo[2](2,6-di(1H-imidazol-1-yl)pyridine)[2](1,4-dimethylene benzene)) and neutral small molecules induce one-dimensional (1D) ‘sandwich’ chain self-assembly. Unlike most of the reported π?π stacking system, the 1D “sandwich” chain expands with the direction parallel to stacking π surfaces on 1⁴⁺ and that on molecule 2, 3, 4 or 5 (2 = p-xylene, 3 = benzene-1,4-diamine, 4 = 4,4′-bipyridine, 5 = [1,1′-biphenyl]-4,4′-diol). Moreover, the π?π stacking modes of 1D self-assembly are seriously small molecule adduct dependent. Combined with the other weak interactions (e.g. intermolecular hydrogen bonding), the new substrate design and control strategy can expand the 1D ‘sandwich’ chain (e.g. [1⁴⁺·4]_n) into higher order structure (e.g. two-dimensional (2D) network [1⁴⁺·4·6]_n, 6 = hydroquinone) even in large scale (~280 mg). This 2D network structure, which keeps stable under 423 K, shows highly selective gas absorption of CO₂ over N₂.