亲电缩聚反应合成芳香环状低聚醚酮砜及其开环聚合

"假高稀"条件下,以邻苯二酰氯为酰基化试剂,Lewis碱NMP存在下,通过亲电缩聚反应高产率地合成了2种芳香环状聚醚酮砜低聚物,利用MALDI-TOF-MS,NMR,GPC,FTIR,DSC等手段对环状结构进行了精确的表征.在负离子引发剂联苯双酚钾存在下,环状低聚物3a进行熔融开环聚合,得到了高分子量的线型聚合物,Tg为221.8℃.利用流变仪监测了环状低聚物3a开环聚合过程中的流变行为,结果表明,开环聚合初期的引发阶段,熔融体的黏度低于10Pa.s,随着时间的延长,黏度快速增长,而且低黏度的引发阶段随着引发剂浓度的增加而变短.     

Synthesis and ring‐opening polymerization of macrocyclic aryl ketone oligomers

A series of macrocyclic aryl ketone oligomers were prepared by the reaction of phthaloyl dichloride or isophthaloyl dichloride with various bridge‐linking electron‐rich aromatic hydrocarbons 3a–d under pseudo‐high dilution conditions in the presence of Lewis base via Friedel–Crafts acylation reaction. Detailed structural characterization of these oligomers confirmed the cyclic nature by a combination of MALDI‐TOF‐MS, GPC, and ¹H NMR analyses. These cyclic ketone oligomers have high solubility in organic solvents and the cyclic oligomers derived from phthaloyl dichloride are amorphous. The cyclic ketone oligomers readily undergo anionic ring‐opening polymerization in the melt by using potassium 4,4′‐biphenoxide as the initiator, producing linear, high molecular weight poly(ether ketone)s. Moreover, the isothermal chemorheology of the ring‐opening polymerization of cyclic oligomers 4a and 4b was also investigated. The results show that the shear viscosity of the molten reactive mixture is lower than 10 Pa · S at a constant shear rate of 0.05 rad/sec and increases slowly in the initial stage of ring‐opening polymerization. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis,characterization, and ring-opening polymerization of novel high Tg macrocyclic oligomers based on 1,2-dihydro-4-(4-hydroxyphenyl)(2H)- phthalazin-1-one

Preparation of novel high T_g (220–280°C) macrocyclic oligomers in high yield by the reaction of 1,2-dihydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one with activated difluoro-monomers is described. The reaction, conducted under pseudo-high dilution conditions, produces cyclic oligomers in 90–97% isolated yield. Detailed structural characterization of these novel oligomers by the combination of NMR, MALDI–TOF–MS, GPC, and reverse-phase HPLC confirm the cyclic nature and reveal the composition of these cyclic oligomers. MALDI–TOF–MS which enables the detection of oligomers with mass up to 6000 Da, is shown to be a very powerful tool for determination of and the proof of the cyclic nature of the cyclic oligomers. The MALDI results provide answers to the possible combinations of monomer units in the cyclic oligomeric components for random co-cyclic oligomers. Rheological measurement of cyclic oligomers 3c shows that the cyclic oligomers are thermally stable in the melt and the molten cyclic oligomers essentially behave like Newtonian fluids. At 340°C and 100 s⁻¹ the steady-state shear viscosity of the molten cyclic oligomers 3c is only about 14 poise. Ring-opening polymerization of the co-cyclic oligomers 4 to a high molecular weight polymer with M_w = 87,000 is achieved by heating at 340°C for 45 min in the presence of a nucleophilic initiator. © 1996 John Wiley & Sons, Inc.     

Synthesis and ring-opening copolymerization of cyclic aryl ester dimers

Two kinds of cyclic aryl ester dimers have been synthesized by reaction of phthaloyl dichloride with bisphenols via interfacial polycondensation. The cyclic dimers readily undergo anionic ring-opening polymerization or copolymerization in the melt by using sodium benzoate as the initiator, producing linear, high molecular weight polyesters. The contents of cyclic dimers in the homopolymers P1, P2, and copolymer P12 are 13.7%, 10.2%, 2.9%, respectively, which indicates that ring-opening copolymerization of cyclic dimers may impel the conversion of cyclic dimers and decrease the content of cyclic dimers in the resulting copolymer. Moreover, the isothermal chemorheology of the ring-opening copolymerization of cyclic dimers indicates that the reactivemoltenmixture has low shear viscosity and the viscosity increases slowly in the initial stage of ring-opening polymerization.     

Isolation,spectra, structure,and ring-opening polymerization of strained macrocyclic aryl(ether ketone) dimer

Macrocyclic arylene ether ketone dimer was isolated from a mixture of cyclic oligomers obtained by the nucleophilic substitution reaction of bisphenol A and 4,4′-difluorobenzophenone and easily polymerized to high molecular weight linear poly-(ether ketone). The cyclic compound was characterized by FTIR, ¹H- and ¹³C-NMR, and single-crystal x-ray diffraction. Analysis of the spectral and crystal structure reveals extreme distortions of the phenyl rings attached to the isopropylidene center and of the turning points of the molecular polygons. The release of the ring strain on ring-opening combined with entropical difference between the linear polymer chain and the more rigid macrocycle at temperatures of polymerization may be the proposed motivating factors in the polymerization of this precursor to high molecular weight poly(ether ketone). © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1753–1761, 1997     

Cyclic(arylene ether) oligomers containing the phenylphosphine oxide moiety

A series of cyclic(arylene ether) oligomers containing the phenylphosphine oxide moiety has been synthesized by reaction of bis(4-fluorophenyl)phenylphosphineoxide with dihydroxy compounds 1a–d as well as 1,2-dihydro-4-(4-hydroxyphenyl) (2H)phthalazin-1-one in DMF in the presence of anhydrous K₂CO₃ under high dilution conditions. These cyclic oligomers are amorphous and have high solubility in organic solvents. The MALDI-TOF-MS technique has been used as a powerful tool to analyze these cyclic systems. The cyclic(arylene ether) oligomers readily undergo anionic ring-opening polymerization in the melt at 350°C by using potassium 4,4′-biphenoxide as the initiator, affording linear, high molecular weight poly(arylene ether)s containing the phenylphosphine oxide moiety. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 519–526, 1998     

SYNTHESIS, CHARACTERIZATION AND RING-OPENING POLYMERIZATION OF CYCLIC (ARYLENE PHOSPHONATE) OLIGOMERS

INTRODUCTIONThe use of cyclic oligomers as macrocyclic precursors for the preparation of high performance polymers byring-opening polymerization (ROP) has sparked much interest in recent years. It could produce a revolutionarychange in the preparation of advanced composite materials, and is of great importance in the polymerizationprocess yielding polymers such as the reinforced reactive injection model (RRIM) and the resin transfer model(RTM) etc. Within the last 10 years, the synthes…     

Poly(aryl ether phenylquinoxalines) via anionic ring opening polymerization of macrocycles

A cyclic poly(aryl ether phenylquinoxaline) was prepared via the self-polymerization of 1 in an N-methyl-2-pyrrolidone (NMP) solution containing base using a pseudo-high dilution polymerization condition. The macrocycle formation of 1 was carried out in the presence of potassium carbonate in a NMP/toluene solvent mixture at a solids content of 1%. The water generated by phenoxide formation was removed as an azeotrope with toluene 170 °C. A concentrated solution of the macrocycle was added to the reaction mixture over an 8 hour period. The reaction was allowed to proceed for an additional 24h to ensure quantitative reaction. A number of characterization techniques were used to study the cyclization of 1 including GPC, HPLC, H NMR and matrix-assisted laser desorption ionization (MALDI) mass spectroscopy. The MALDI-TOF mass spectrum of the cyclization of 1 clearly showed that a mixture of macrocycles is obtained, with the expected distribution of molecular weights. Facile ring opening polymerization of the cyclic poly(aryl ether phenylquinoxaline) oligomers was accomplished with a nucleophilic initiator. High polymer was obtained for each polymerization temperature (η = 0.4–0.5 dl/g in NMP), however, prolonged reaction time resulted in significant gel formation. The Tg's were high and commensurate with the high molecular weight linear analog (250 °C).     

DFT study of the role of substituents in tin(II) bis(amidoethyl)amine complexes used for ε-caprolactone polymerization

DFT simulations of ring-opening polymerization of ε-caprolactone in the presence of two stannylenes based on bis(2-amidoethyl)amine ligands demonstrated that rate limiting step of the whole process is the nucleophilic attack of a metal initiator with the formation of the tetrahedral carbon from sp² carbon atom of the carboxy group. The presence of electron-withdrawing groups at the terminal nitrogen atoms of the ligands leads to decrease in the activation energy of the rate limiting step.     

Living ring-opening polymerization of cyclic carbonate using cationic zirconocene complex as catalyst

Living ring-opening polymerization of the cyclic carbonate 1,3-dioxepan-2-one was achieved by using the cationic zirconocene complex [Cp₂ZrMe]⁺[B(C₆F₅)₄]⁻ as catalyst at room temperature. A linear relation between conversion and molecular weight of the obtained polymer was observed. Furthermore, block copolymerization of the cyclic carbonate and ε-caprolactone was successfully performed.     

Cationic polymerization behavior of seven-membered cyclic sulfite

Cationic ring-opening polymerization behavior of a seven-membered cyclic sulfite ( 1 ) was examined. 1 was prepared by the reaction of 1,4-butanediol with SOCl₂ in 58% yield. The cationic polymerization of 1 was carried out at 0, 25, 60, or 100°C with trifluoromethanesulfonic acid (TfOH), methyl trifluoromethanesulfonate (TfOMe), BF₃ · OEt₂, SnCl₄, methyl p-toluenesulfonate (TsOMe), or MeI as an initiator in bulk under a nitrogen atmosphere to afford the polymer with M̄_n 1000–10,400. The order of activities of the initiators for 1 was as follows, TfOH ≅ TfOMe > SnCl₄ > BF₃ · OEt₂ > TsOMe ≅ MeI. The polymerization of 1 with TfOMe afforded a poly(sulfite) below 25°C, but afforded a polymer containing an ether unit at 60°C, which was formed by a desulfoxylation. The higher the activity of the initiator was, the more easily the desulfoxylation occurred. We expected volume expansion on polymerization because cyclic sulfites have large dipole moment values, but it turned out that 1 showed 4.34% shrinkage on polymerization. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3673–3682, 1997     

Synthesis and characterization of four-armed poly(1,3-dioxepane) tetraol

A new four-armed poly(1,3-dioxepane) tetraol was prepared by cationic ring-opening polymerization of 1,3-dioxepane (DOP) in the presence of 6,6-bis(5-hydroxyl-2-oxapentyl)-4,8-dioxaundecanediol-1,11 (THA) with triflic acid(I) as initiator. The structure of the poly(DOP) tetraol obtained was characterized by ¹H and ¹³C NMR spectra. The molecular weights of the obtained tetraols were controlled by the mole ratio of DOP consumed to initial THA, and it was found that each macromolecule contains only one THA unit on the average. GPC studies showed that the cyclic oligomers in the products were negligible. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2347–2353, 1999     

Ring opening polymerization of tetrahydrofuran catalysed by maghnite-H+

The cationic ring-opening polymerization of tetrahydrofiiran using maghnite-H~+ is reported.Maghnite-H~+,is a non-toxic solid catalyst issued from proton exchanged montmorillonite clay.Polytetrahydrofuran,also called "poly(butandiol) ether",with acetate and hydroxyl end groups was successfully synthesized.Effects of reaction temperature, weight ratio of initiator/monomer and reaction time on the conversion of monomer and on the molecular weight are investigated.A cationic mechanism of the reaction was proposed.This chemistry can be considered as a suitable route for preparing poly(THF) as a soft segment for thermoplastic elastomers.     

Ring-opening polymerization of six- and seven-membered cyclic pseudoureas

The cationic ring-opening polymerization of six-membered cyclic pseudoureas, 2-(1-pyrrolidinyl)- ( 2a ) and 2-morpholino-5,6-dihydro-4H-1,3-oxazine ( 2b ), was examined, which proceeded in two different ways, depending on the nature of initiator. The polymerization of 2 with methyl p-toluenesulfonate or trifluoromethanesulfonate (MeOTf) produced poly[(N-carbamoylimino)trimethylene], while that with benzyl chloride or bromide or methyl iodide gave a polymer consisting of 1,3-diazin-2-one-1,3-diylalkylene unit (the main component) and (N-carbamoylimino)trimethylene unit. The cationic ring-opening polymerization of seven-membered cyclic pseudourea, 2-(1-pyrrolidinyl)-4,5,6,7-tetrahydro-4H-1,3-oxazepine ( 3 ) was also examined. The polymerization of 3 with MeOTf as initiator gave poly{[N-(1-pyrrolidinycarbonyl)imino]tetra-methylene}. With benzyl chloride, on the other hand, no polymerization of 3 proceeded but, instead, the quantitative isomerization of 3 to 1,1′-carbonyldipyrrolidine took place. The polymerization mechanism of 2 and 3 as well as the isomerization mechanism of 3 were discussed with comparing them to the polymerization mechanism of five-membered pseudoureas. © 1977 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 933–945, 1997     

Mechanism of dispersion polymerization of L-lactide initiated with 2,2-dibutyl-2-stanna-1,3-dioxepane

 Biodegradable polyester microspheres were synthesized directly by ring-opening polymerization of l-lactide initiated with 2,2-dibutyl-2-stanna-1,3-dioxepane. The polymerizations were carried out at 95 °C in a mixture of organic solvents (heptane/1,4–dioxane 4:1 v:v), in the presence of poly(dodecyl acrylate)-g-poly(ɛ-caprolactone) used as a surface-active agent. Under these conditions the poly(L-lactide) synthesized was shaped into microspheres. The absence of new particles in the polymerizations with multistep monomer addition indicated that after the formation of particle seeds the propagation proceeds exclusively inside the microspheres. The mean volume of these microspheres was proportional to the monomer conversion. It was found that regardless of the initiator concentration the average number of poly(L-lactide) macromolecules in one microsphere was 1.84 × 10⁸. Matrix-assisted laser desorption ionization time of flight spectroscopy of poly(L-lactide) in the microspheres indicated that the propagation in the particles was accompanied by intra- and intermolecular transesterification side reactions, resulting in reshuffling of the polymer segments and the formation of cyclic oligomers. Received: 20 December 2000 Accepted: 7 June 2001     

More about the polymerization of lactides in the presence of stannous octoate

The ring-opening polymerization of lactide cyclic monomers in the bulk in the presence of tin(II) 2-ethylhexanoate (stannous octoate or SnOct₂) was reexamined under conditions allowing for the end group characterization of growing chains by high-resolution ¹H-NMR. Data collected for low values of the monomer/initiator (M/I) ratio showed that the DL -lactide ring was opened to yield lactyl octoate-terminated short chains. A cationic-type mechanism involving co-initiation by octanoic acid was proposed to account for experimental findings. The formation of a side product, hydroxytin(II) lactate (HTL), was found which appeared able to initiate lactide polymerization and to yield a high molecular weight PLA50 polymer. However the polymerization with stannous octoate was faster than the HTL one. Anyhow, data suggested that both SnOct₂ and HTL are likely to act simultaneously as initiators during the polymerization of lactides in the presence of SnOct₂. A complete reaction scheme was proposed to account for the presence of the various compounds likely to be formed under these conditions. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3431–3440, 1997     

Gradient copolymers of ε-caprolactone and δ-valerolactone via solvent-free ring-opening copolymerization with a pyridyl-urea/MTBD system

The ring-opening copolymerization of ε-caprolactone and δ-valerolactone was carried out under solvent-free conditions with a pyridyl-urea ( 6C-PU )/7-methyl-1,5,7-triazabicyclo[4.4.0]dec-5-ene catalytic system by premixing two monomers, yielding gradient copolyesters with cyclic and linear structures in the absence or presence of an initiator, respectively. The random and block copolyesters of these two monomers were also prepared for comparison. The results of ¹H and ¹³C NMR spectra determined the linear and cyclic structure of copolymers. The kinetic experiment was used to determine the consuming rates of two monomers during the polymerization. The topologies and thermal properties of all the copolymers were characterized and compared by NMR and DSC.     

The preparation and characterization of novel cocylic(arylene disulfide) oligomers

A series of homo‐ and cocyclic(arylene disulfide) oligomers were synthesized under high dilution conditions by the catalytic oxidation of arylenedithiols with oxygen in the presence of a copper‐amine catalyst in DMAc. The aryl groups contained moieties such as sulfone, ether, and ketone. The free radical ring‐opening polymerization of these cyclic(arylene disulfide) oligomers led to the formation of linear poly(thio arylene)s. The homo‐ and cocyclic(arylene disulfide) oligomers were characterized by gradient high pressure liquid chromatography (HPLC), get permeation chromatography (GPC), ¹H‐NMR, and differential scanning calorimetry (DSC) methods. These cocyclic(arylene disulfide) oligomers except those containing sulfone moiety had lower melt flow temperature as low as 140 °C and therefore could readily undergo free radical ring‐opening polymerization under mild conditions. The glass transition temperatures of these cocyclics ranged from 72.3 to 190.0 °C, while the glass transition temperatures of the polydisulfides derived from these cocyclics ranged from 78.4 to 194.5 °C. In this article, a new method of preparing arylene dithiols 4,4′‐oxybis(benzenethiol) and diphenylmethane‐4,4′‐dithiol is reported. Copyright © 2003 John Wiley & Sons, Ltd.     

THE EFFECTS OF MONOMER STRUCTURE OF CYCLIC KETENE ACETALS ON THE BEHAVIOR OF CONTROLLED RADICAL RING-OPENING POLYMERIZATION

Polymerization of three cyclic ketene acetals: i.e., 5,6-benzo-2-methylene-1,3-dioxepane (BMDO), 2-methylene-4-phenyl-1,3-dioxolane (MPDO) and 4, 7-dimethyl-2-methylene-1, 3-dioxepane(DMMDO) were carried out in the presence ofethyl α-bromobutyrate/CuBr/2, 2'-bipyridine respectively. The structures of poly(BMDO), poly(MPDO) and poly(DMMDO)were characterized by ~1H and ~(13)C-NMR spectra. The effects of monomer structure on the behavior of atom transfer freeradical ring-opening polymerization were investigated and the mechanism of controlled free radical ring-openingpolymerization was discussed.     

Ring-Opening Metathesis Polymerization of Cyclooctyne Employing Well-Defined Tungsten Alkylidyne Complexes

Summary: The ring-opening metathesis polymerization of cyclooctyne was studied was studied in the presence of catalytic amounts of the tungsten alkylidyne complexes [RCW(NIm^tBu){OCMe(CF₃)₂}₂] ( 1a: R = CMe₃, 1b: R = Ph). The resulting polymers show relatively narrow polydispersities with the PDI ranging from 1.2 to 2.4. Treatment of 1b with cyclooctyne in dilute toluene or hexane solution afforded only low molecular weight oligomers. The mass spectra of these oligomers indicate the existence of macrocycles of the formula [C(CH₂)₆C]_n (n = 3–9). In contrast, reactions at high substrate concentration led to mixtures of cyclic oligomers and linear polymers, which is probably a result of ring-chain equilibria, established in agreement with the Jacobson-Stockmayer theory of macrocyclization. In contrast, treatment of neat cyclooctyne with a catalytic amount of the catalyst produced medium molecular weight polymers in good yields.