Synthesis and characterization of copoly(arylene sulfide)s

Copolymerizations of p-dichlorobenzene (DCB)/4-bromophenyl ether (BPE), DCB/4,4′-dibromobiphenyl (DBB), and DBB/BPE pairs with sodium sulfide under high temperature (270–290°C) utilizing N-methyl-2-pyrrolidinone (NMP) as solvent were carried out to give C(DCB/BPE), C(DCB/DBB), and C(DBB/BPE) copolymers, respectively. The reactivity of dihaloaromatic monomers toward thiolate anion in the polycondensation reaction followed the order DBB > DCB > BPE. The reactivity gap between DBB and DCB toward thiolate anion seemed to be smaller than that between BPE and DCB, resulting in both high yield and high molecular weight in the C(DCB/DBB) copolymers compared to C(DCB/BPE) copolymers. The copolymerization of DBB/BPE pair with sodium sulfide, which has larger reactivity gap than the DCB/DBB or DCB/BPE pair, gave mixtures of PBS and PPSE homopolymers especially in the range of 50–80 mol % BPE in the feed. The C(DCB/DBB) and C(DCB/BPE) copolymers, however, exhibited random copolymer character in all comonomer ratios in the feed as evidenced by copolymer composition and DSC data. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2311–2317, 1999     

Synthesis and characterization of ran-copoly (p-phenylene sulfide sulfone/ketone)s

Random copoly(p-phenylene sulfide sulfone/ketone)s (PPSS/K) are prepared in high yield by the polycondensation of sodium hydrosulfide (NaSH) with bis(4-chlorophenyl) sulfone (BCPS) and 4,4′-dichlorobenzophenone (DCBP). The polymerization is conducted between 200–220°C, depending on the composition of the copolymer, and in the presence of water without any detrimental effects to the molecular weight. The copolymers with sulfone/ketone mole ratios (S : K) > 25 : 75 are amorphous, while the copolymers with S : K ratios ≤ 25 : 75 are crystalline. These materials form tough, creaseable films and exhibit a linear increase in the glass transition temperature with increasing sulfone content. Sulfuric acid solutions of the copolymers are dark orange to red and display an increasing λ_max in the uv-visible spectra as the S:K ratio of the copolymers decreases. © 1994 John Wiley & Sons, Inc.     

Synthesis,characterization, and comparison of properties of new fluorinated poly(arylene ether)s containing phthalimidine moiety in the main chain

Four new poly(arylene ether)s have been prepared by the reaction of N‐phenyl‐3,3‐bis(4‐hydroxyphenyl)phthalimidine (PA) with four different perfluoroalkylated monomers namely 1,3‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) benzene, 4,4′‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) biphenyl, 2,6‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) pyridine, and 2,5‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) thiophene. The poly(arylene ether)s were characterized by different spectroscopic, thermal, mechanical, and electrical techniques. The poly(arylene ether) containing quadriphenyl unit in the main chain showed very high glass transition temperature of 291°C and outstanding thermal stability upto 556°C for 10% weight loss under a 4:1 nitrogen:oxygen mixture. The polymers were soluble in a wide range of organic solvents. Transparent thin films of these polymers exhibited tensile strengths upto 75 MPa and elongation at break upto 32%. The films of these polymers showed low water absorption of 0.26%. Copyright © 2009 John Wiley & Sons, Ltd.     

Crystallization and melting of cold-crystallized poly(phenylene sulfide)

In this study, we report the melting behavior of poly(phenylene sulfide), PPS, which has been cold-crystallized from the rubbery amorphous state. We find that the crystallization kinetics are faster for cold-crystallized PPS than for melt-crystallized material, due to formation during quenching of a short-range ordered, but noncrystalline, structure. We observe that the endothermic response of cold-crystallized PPS at a large undercooling consists of a low temperature endotherm, followed by an exothermic region, and by the main higher melting endotherm. The lower melting peak temperature of cold-crystallized PPS increases as the crystallization temperature increases, but the main upper melting peak temperature remains almost the same. The size of the exothermic region is strongly related to the degree of undercooling, and must be taken into account in order properly to determine the degree of crystallinity of the material prior to the scan. When the crystallization time is varied, we see a systematic decrease in the size of the main endotherm, and an increase in size of the lower melting endotherm. This suggests that a portion of the main endothermic response is due to reorganization during the scan. Annealing will not only increase the degree of crystallinity but also improve the crystal perfection; therefore the ability of an annealed sample to reorganize decreases as the annealing time increases. However, an additional third melting peak is seen when a cold-crystallized sample is annealed at high temperature for a sufficiently long residence time. The existence of the third melting peak suggests that more than one kind of distribution of crystal perfection may occur when PPS has been cold-crystallized and subsequently annealed.     

Poly(arylene sulfide)s via nucleophilic aromatic substitution reactions of halogenated pyromellitic diimides

Nucleophilic aromatic substitution (SNAr) reactions are exploited to prepare poly(arylene sulfide)s (PAS's) via the reaction of bis-thiolates and dibrominated pyromellitic diimide (PMDI) derivatives. Small-molecule model studies reveal the reaction is well-defined and proceeds in quantitative yield in practical times at room temperature. Variation in comonomer feed ratios allowed some control over target polymer molecular weights in the step polymerization, but control was likely limited by the relatively poor polymer solubility in the dipolar aprotic solvents typically employed to promote SNAr reactions. One substitution pattern produces a steric “pocket” around the PMDI units, inducing a peculiar solubility trend in halogenated solvents; that is, greatly reduced solubility in CHCl₃ relative to CH₂Cl₂ and C₂H₂Cl₄. One example small-molecule readily dissolves in CHCl₃ at room temperature, then rapidly grows poorly soluble crystals revealed by single-crystal XRD to contain CHCl₃ molecules in the steric pockets. Finally, the recently demonstrated depolymerization of phthalonitrile-based PAS's via ipso substitution with monothiolates as chain scission agents yields quantitative molecular weight reduction to monomeric species from the polymers reported here.     

Synthesis and characterization of new poly(arylene ether)s containing heterocyclic units. II.

A series of new poly(arylene ether)s, containing naphthalene, pyridine, and quinoline units have been prepared by solution condensation polymerization. The synthesis involves nucleophilic displacement of aromatic dihalides with aromatic potassium bisphenates in an anhydrous dipolar aprotic solvent at elevated temperatures. The polymers, having inherent viscosity from 0.24 to 1.32 dL/g, were obtained in quantitative yield, have excellent thermal stability as shown by 10% weight loss temperatures in nitrogen and air (above 450 and 430°C, respectively) and high glass transition temperatures (in the range of 150–220°C). The introduction of quinoline moieties in the polymer backbone positively influences the thermal properties, such as high T_g/T_m ratios. © 1995 John Wiley & Sons, Inc.     

含二茂铁齐聚苯乙炔分子导线的合成

通过二碘代二茂铁与不同炔化物进行Sonogashira偶联反应,合成了3种新颖的含有二茂铁单元的苯乙炔齐聚物,用1H NMR、13C NMR和MS测试技术分别对其结构进行了表征。 并借助量子化学计算对3种分子的电子结构进行了预测,结果显示,该类型分子导线具有不同于其它类型苯乙炔齐聚物的LUMO能级持续衰减特征,因此极有可能具备极为优良的电子传输性能。     

Co‐poly(aryl ether sulfone)s containing phthalimidine moiety in the main chain

Several new co‐poly(arylene ether sulfone)s have been prepared by the reaction of 4,4′‐fluorodiphenyl sulfone (FDS) with different bisphenols namely 4,4′‐isopropylidenediphenol (BPA), 4,4′‐hexafluoroisopropylidenediphenol (6F‐BPA), and N‐phenyl‐3,3‐bis(4‐hydroxyphenyl)phthalimidine(PA). The homo‐poly(arylene ether sulfone)s are named as 1a, 2a, and 3a. The copolymers namely 2b, 2c, 2d and 3b, 3c, 3d have been prepared, respectively, on reaction of FDS with BPA or 6F‐BPA using different molar ratios of PA such as 25, 50, and 75. The poly(aryl ether sulfone)s 1a containing PA unit in the main chain showed a very high glass transition temperature of 280°C and an outstanding thermal stability up to 510°C for 5% weight loss under synthetic air. Depending on the mole% of PA, the glass transition temperatures of the copolymers can be varied. The polymers were soluble in a wide range of organic solvents. Transparent thin films of these polymers exhibited tensile strengths upto 84 MPa and Young's modulus up to 3.16 GPa. The films of these polymers showed low water absorption of 0.24%. Copyright © 2009 John Wiley & Sons, Ltd.     

Thermal analysis study of the effect of molecular weight on constrained amorphous phase in poly(phenylene sulfide)

We report a thermal analysis study of the effect of molecular weight on the amorphous phase structure of poly(phenylene sulfide), PPS, crystallized at temperatures just above the glass transition temperature. Thermal properties of Fortron PPS, having viscosity average molecular weights of 30000 to 91000, were characterized using temperature modulated differential scanning calorimetry (MDSC). We find that while crystallinity varies little with molecular weight, the heat capacity increment at the glass transition decreases as molecular weight decreases. This leads to a smaller liquid-like amorphous phase, and a larger rigid amorphous fraction, in the lower molecular weight PPS. For all molecular weights, constrained fraction decreases as the scan rate decreases.This research is supported by the U. S. Army Research Office through contract DAAH04-96-1-0009. The authors thank Hoechst Celanese for providing different molecular weight Fortron samples and Dr. George Collins for providing sample information. The authors acknowledge the assistance of Elizabeth Oyebode and Leonardo Grimaldi with sample preparation and MDSC work.     

New Semiconducting Poly(arylene sulfide)s: Synthesis,Characterization, and Optical Properties

New semiconducting soluble poly(arylene sulfide)s were synthesized by Wittig polycondensation. The arylene moieties consist of distyrylbiphenyl (P1) and distyrylbithiophene (P2) π-conjugated systems. The polymers are fully amorphous and show good thermal stability. The absorption and photoluminescence properties of the polymers were investigated. P1 film has an optical gap of 2.95 eV and exhibits green-blue fluorescence. P2 shows a longer effective conjugation length with a gap of 2.42 eV and emits in the orange region. The HOMO/LUMO energy levels were estimated by cyclic voltammetry measurements. Single-layer diodes were fabricated and show relatively low turn-on voltages.     

亚砜还原法合成聚苯醚硫醚的结构与性能研究

以氟苯和氯化亚砜反应合成了4,4’-二氟二苯亚砜,并将其与4,4’二羟基二苯硫醚在N-甲基吡咯烷酮溶剂中进行亲核取代反应合成了聚苯醚硫醚醚亚砜,用乙二酰氯/四丁基碘化铵还原该亚砜聚合物制备了聚苯醚硫醚。用红外光谱和核磁共振谱对合成单体的结构进行了确认,同时对聚合物进行了红外光谱、核磁共振、元素分析、X射线光电子能谱、X射线衍射、DSC分析、TG/DTG以及溶解性测试。结果表明聚苯醚硫醚样品具有氧醚和硫醚交替的线性结构,特性粘度为0.55 dL/g的PPSE熔点达236℃,在氮气条件下,样品起始分解温度和最大分解速率处温度分别为359℃和514℃,在700℃时的重量保留率为43.3%,且在加热条件下能溶解于N-甲基吡咯烷酮(NMP)、二甲基乙酰胺(DMAc)、二甲基甲酰胺(DMF)等极性有机溶剂中。     

Application of zone-drawing and zone-annealing method to poly(p-phenylene sulfide) fibers

A zone-drawing and zone-annealing treatment was applied to poly(p-phenylene sulfide) fibers in order to improve their mechanical properties. The zone-drawing (ZD) was carried out at a drawing temperature of 90°C under an applied tension of 5.5 MPa, and the zone-annealing (ZA) was carried out at an annealing temperature of 220°C under 138.0 MPa. The differential scanning calorimetry (DSC) thermogram of the ZD fiber had a broad exothermic transition (T_c = 110°C) attributed to cold-crystallization and a melting endotherm peaking at 286°C. The T_c of the ZD fiber was lower than that (T_c = 128°C) of the undrawn fiber. In the temperature dependence of storage modulus (E′) for the ZD fiber, the E′ values decreased with increasing temperature, but increased slightly in the temperature range of 90–100°C, and decreased again. The slight increase in E′ was attributable to the additional increase in the crosslink density of the network, which was caused by strain-induced crystallization during measurement. The resulting ZA fiber had a draw ratio of 6.0, a degree of crystallinity of 38%, a tensile modulus of 8 GPa, and a tensile strength of 0.7 GPa. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1731–1738, 1998     

Effect of amorphous precipitated silica on the properties and structure of poly(p-phenylene sulfide)

Using a precipitation technique, silicas were obtained from sodium metasilicate solution employing an acidic agent. Alcohol solutions were used in the process of production of highly dispersed silicas, which resulted in partial blocking of the silica surface silanol groups. Moreover, studies on morphology and microstructure using transmission electron microscopy and scanning electron microscopy were performed. The size distributions of primary particles and aggregate and agglomerate structures were determined using a ZetaPlus instrument using the dynamic light scattering method. The structure and molecular dynamics of the nanocomposite, consisting of poly (p-phenylene sulfide) (PPS) and of the precipitated silica, were studied using atomic force microscopy and nuclear magnetic resonance. It was proved that during annealing the fragmentation of PPS agglomerates takes place. This phenomena probably resulted from repulsion forces existing between agglomerates and aggregates. Fragmentation in the polymer network probably resulted from repulsion forces between agglomerates and smaller aggregates. Received: 7 November 2000 Accepted: 5 April 2001     

Dielectric relaxation of poly(phenylene sulfide) containing a fraction of rigid amorphous phase

The dielectric relaxation behavior of poly(phenylene sulfide), PPS, has been investigated from room temperature to 180°C. This study was undertaken to examine the mobility of the amorphous phase through the glass transition region, to determine the contribution that rigid amorphous phase material makes to the relaxation process. Semicrystalline samples contain a fraction of the rigid amorphous phase, which was determined from the heat capacity increment at the glass transition, using degree of crystallinity determined from x-ray scattering. In the dielectric experiment, we measured the temperature and frequency dependence of the real and imaginary parts of the dielectric function. ε″ vs. ε′ was used to determine the dielectric relaxation intensity, δε = ε_s–ε∞, at temperatures above the glass transition. For amorphous PPS, δε decreases as temperature increases, while for all semicrystalline PPS, δε increases with temperature. The ratio of semicrystalline intensity to amorphous intensity determines the total fraction of dipoles which are already relaxed at a given temperature. Results indicate that more and more rigid amorphous phase material relaxes as the temperature is increased. This provides the first evidence that rigid amorphous phase material in PPS contains chains that possess different levels of molecular mobility. Finally, to the temperature of the loss peak maximum, at a given frequency, we assign the value of the dielectric T_g. For both melt and cold crystallization, the dielectric T_g systematically decreases as the crystallization temperature increases, and as the fraction of rigid amorphous phase decreases.     

Synthesis and properties of multiblock copoly(arylene ether)s containing superacid groups for fuel cell membranes

A series of block copoly(arylene ether)s containing pendant superacid groups were synthesized, and their properties were investigated for fuel cell applications. Two series of telechelic oligomers, iodo‐substituted oligo(arylene ether ketone)s and oligo(arylene ether sulfone)s, were synthesized. The degree of oligomerization and the end groups were controlled by changing the feed ratio of the monomers. The nucleophilic substitution polymerization of the two oligomers provided iodo‐substituted precursor block copolymers. The iodo groups were converted to perfluorosulfonic acid groups via the Ullmann coupling reaction. The high degree of perfluorosulfonation (up to 83%) was achieved by optimizing the reaction conditions. Tough and bendable membranes were prepared by solution casting. The ionomer membranes exhibited characteristic hydrophilic/hydrophobic phase separation with large hydrophilic clusters (ca. 10 nm), which were different from that of our previous random copolymers with similar molecular structure. The block copolymer structure was found to be effective in improving the proton‐conducting behavior of the superacid‐modified poly(arylene ether) ionomer membranes without increasing the ion exchange capacity (IEC). The highest proton conductivity was 0.13 S/cm at 80 °C, 90% relative humidity, for the block copolymer ionomer membrane with IEC = 1.29 mequiv/g. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effects of solvent treatment on crystallization kinetics of poly(p-phenylene sulfide)

Isothermal melt crystallization kinetics were investigated by differential scanning calorimetry (DSC) for virgin and α-chloronaphthalene solvent-treated poly(phenylene sulfide) (PPS) systems. The overall crystallization rates were found to be much faster for the solvent-treated PPS than for the virgin neat PPS. Additionally, the Avrami crystallization plot for the solvent-treated PPS samples appeared as two straight portions with an apparent discontinuity, but as a continuous straight line for the virgin PPS system. After the treatment of solvent dissolution and subsequent drying, the residual trace α-chloronaphthalene, upon being quenched to the crystallization temperatures, initiated some localized solvent-induced nuclei-like crystals in PPS. It was the nuclei that enhanced secondary crystallization in treated PPS during the second stage, and the higher extents of secondary crystallization in the solvent-treated PPS caused the apparent discontinuous break in the Avrami plots. The causes for the difference were explained and the mechanism of the sequential primary/secondary crystallization kinetics for the solvent-treated PPS was satisfactorily described with a proposed series-parallel crystallization model. ©1995 John Wiley & Sons, Inc.     

Synthesis and flammability of copoly(isophthalamide)s. II. With pendant phosphorus groups

A series of copoly(isophthalamide)s containing pendant phosphorus, dialkoxyphosphinylphenylene, diphenylphosphinylphenylene, and diphenylphosphinylamino groups were prepared. The introduction of phosphorus groups was performed to a degree of ca. 5–17 mol %. From the limiting oxygen index (LOI) measurements, it was found that the LOI of P-substituted polyamides increased by ca. 14–40%. From TG and DTG analysis the maximum rate and the percentage of mass loss of the decomposition stages were evaluated. From these measurements the mode of action of phosphorus groups in the solid or gas phase was assessed. In the solid phase, due to crosslinking reactions, a reduction of the maximum rate and the percentage of mass loss in the decomposition stage of main chain amide bonds was observed. In this case the increase of the char yield at 700°C of the P-substituted polyamides was in the range of 21–36%. © 1993 John Wiley & Sons, Inc.     

Comparative study of the thermal properties of related aromatic polyhydrazides and poly(1,3,4-oxadiazole)s

Studies were undertaken to ascertain the thermal behavior of several new types of aromatic polyhydrazides and poly(1,3,4-oxadiazole)s containing different functional groups. Results of thermal analysis investigations indicate that all the polyoxadiazoles are remarkably heat-resistant when heated in nitrogen at elevated temperature but somewhat less heat-resistant than fully aromatic polyoxadiazoles. Most of the new polyoxadiazoles decompose when heated to about 450°C. The incorporation of tetraphenyl silane, hexafluoroisopropylidene, phthalido or phenoxytherephthalic groups into the main chain decrease the glass transition temperature of aromatic poly(1,3,4-oxadiazole)s. In the case of the silicon-containing polymers the glass transition temperature is independent of the other groups incorporated in the same macromolecule. The cyclization process of all investigated polyhydrazides takes place in the range between 320 and 390°C.     

Miscibility predictions for poly(phenylene sulfide): Heats of mixing of model compounds

Calorimetry was used to gain insight into the thermodynamics of mixing of unlike species, designed to represent organic polymers. These results are to be useful in predicting miscibility between various polymers and poly(arylene sulfides). Phenyl sulfide (PS) and phenyl disulfide (PSS) were used as models for poly(phenylene sulfide) (PPS) and were mixed with model compounds that are representative of other polymer classes. The enthalpy of mixing was measured for a large number of combinations. The results are interpreted in terms of a summation of the effects of specific interactions and dispersive forces. It is seen from these data that the presence of aromatic side groups enhances the miscibility of the species with the poly(phenylene sulfide) model compound. Furthermore, exothermic heats of mixing were observed between the PPS model and compound. Furthermore, exothermic heats of mixing were observed between the PPS model and compounds that contain carbonyl, amide, or amine moieties. Finally, the sulfur atom in PPS seems to play only a minor role in determining its interactions with other species. Replacing sulfur with oxygen (or even an alkyl group) is seen to have very little effect on the heats of mixing results. © 1994 John Wiley & Sons, Inc.     

Poly(arylene ether)s and poly(arylene thioether)s containing the 1,2-dihydro-4-phenyl(2H)- phthalazinone moiety

A series of new high molecular weight poly(arylene ether)s containing the 1,2-dihydro-4-phenyl(2H)phthalazinone moiety have been synthesized. The inherent viscosities of these polymers are in the range of 0.33–0.64 dL/g. They are amorphous and readily soluble in chloroform, DMF, and DMAc. The glass transition temperatures of the polymers range from 241 to 320°C and the 5% weight loss temperatures in nitrogen atmosphere range from 473 to 517°C. The hydroxy group in the monomer 1,2-dihydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one has been selectively transformed into the N,N′-dimethylthiocarbamate group, which was then rearranged to give the S-(N,N′-dimethylcarbamate) group via the Newman–Kwart rearrangement reaction. A series of poly(arylene thioether)s containing the 1,2-dihydro-4-phenyl(2H)phthalazinone moiety have also been synthesized via two types of reactions, a N C coupling reaction and a one-pot reaction between the S-(N,N′-dimethylcarbamate) and activated dihalo compounds, in diphenyl sulfone in the presence of a cesium carbonate and calcium carbonate mixture. These poly(arylene thioether)s also have high glass transition temperatures (ranging from 217–303°C) and high thermal stabilities. Compared with their poly(ether) analogs, the poly(arylene thioether)s have glass transition temperatures several degrees lower, which is attributed to the more flexible C S C bonds. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36 : 455–460, 1998