Thermal and mechanical properties of a dendritic hydroxyl‐functional hyperbranched polymer and tetrafunctional epoxy resin blends

Blends of a tetrafunctional epoxy resin, tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM), and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 3,3′‐diaminodiphenyl sulfone (DDS) as curing agent. The phase behavior and morphology of the DDS‐cured epoxy/HBP blends with HBP content up to 30 phr were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The phase behavior and morphology of the DDS‐cured epoxy/HBP blends were observed to be dependent on the blend composition. Blends with HBP content from 10 to 30 phr, show a particulate morphology where discrete HBP‐rich particles are dispersed in the continuous cured epoxy‐rich matrix. The cured blends with 15 and 20 phr exhibit a bimodal particle size distribution whereas the cured blend with 30 phr HBP demonstrates a monomodal particle size distribution. Mechanical measurements show that at a concentration range of 0–30 phr addition, the HBP is able to almost double the fracture toughness of the unmodified TGDDM epoxy resin. FTIR displays the formation of hydrogen bonding between the epoxy network and the HBP modifier. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 417–424, 2010     

Micro phase separated epoxy/poly(ε-caprolactone)-block-poly(dimethyl siloxane)-block-poly(ε-caprolactone)/4,4′-diaminodiphenylsulfone systems: Morphology,viscoelasticity, thermo-mechanical properties and surface hydrophobicity

Epoxy resin/4,4′-diaminodiphenylsulfone (DDS) system was modified by the incorporation of poly(ε-caprolactone)-block-poly(dimethyl siloxane)-block-poly(ε-caprolactone) (PCL–PDMS–PCL) triblock copolymer (TBCP). Morphology, viscoelasticity, thermo-mechanical and surface properties of these blends were investigated. All the blends were opaque after curing. PCL blocks of the TBCP were miscible with epoxy resin while the PDMS fraction was immiscible. However in the cured state, both PCL and PDMS blocks were phase separated from epoxy/DDS matrix. The blends exhibited matrix-droplet morphology in which TBCP phase dispersed as spherical domains in epoxy matrix. Addition of TBCP had profound impact on the cure reaction kinetics. Storage modulus and glass transition temperature (T_g) decreased while impact strength significantly increased. Incorporation of 15 phr of TBCP resulted in 80% improvement in impact strength. Further, thermal stability was unaffected while surface hydrophobicity of the blends increased.     

Miscibility and cure kinetics studies on blends of bisphenol-A polycarbonate and tetraglycidyl-4,4′-diaminodiphenylmethane epoxy cured with an amine

Differential scanning calorimetry (DSC) has been applied to characterize the glass transition behavior of the blends formed by bisphenol-A polycarbonate (PC) with a tetrafunctional epoxy (tetraglycidyl-4,4′-diaminodiphenyl methane, TGDDM) cured with 4,4′-diaminodiphenylsulphone (DDS). A rare miscibility in the complete composition range has been demonstrated in these blends. Additionally, the blend morphology was examined using scanning electron microscopy (SEM) and a homogeneous single-phase PC/epoxy network has been observed in the blends of all compositions. Moreover, polycarbonate incorporation has been found to exert a distinct effect on the cure behavior of the epoxy blends. The cure reaction rates for the epoxy-PC blends were significantly higher due to the presence of PC. In addition, the cure mechanism of the epoxy blends was no longer autocatalytic. An n-th order reaction mechanism with n = 1.2 to 1.5 has been observed for the blends of DDS-cured epoxy with PC of various compositions studied using DSC. The proposed n-th order kinetic model has been found to describe well the cure behavior of the epoxy/PC blends up to the vitrification point. © 1995 John Wiley & Sons, Inc.     

Phase separation,porous structure,and cure kinetics in aliphatic epoxy resin containing hyperbranched polyester

Thermosetting blends of an aliphatic epoxy resin and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 4,4′‐diaminodiphenylmethane (DDM) as the curing agent. The phase behavior and morphology of the DDM‐cured epoxy/HBP blends with HBP content up to 40 wt % were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The cured epoxy/HBP blends are immiscible and exhibit two separate glass transitions, as revealed by DMA. The SEM observation showed that there exist two phases in the cured blends, which is an epoxy‐rich phase and an HBP‐rich phase, which is responsible for the two separate glass transitions. The phase morphology was observed to be dependent on the blend composition. For the blends with HBP content up to 10 wt %, discrete HBP domains are dispersed in the continuous cured epoxy matrix, whereas the cured blend with 40 wt % HBP exhibits a combined morphology of connected globules and bicontinuous phase structure. Porous epoxy thermosets with continuous open structures on the order of 100–300 nm were formed after the HBP‐rich phase was extracted with solvent from the cured blend with 40 wt % HBP. The DSC study showed that the curing rate is not obviously affected in the epoxy/HBP blends with HBP content up to 40 wt %. The activation energy values obtained are not remarkably changed in the blends; the addition of HBP to epoxy resin thus does not change the mechanism of cure reaction of epoxy resin with DDM. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 889–899, 2006     

Phase behavior,crystallization, and morphology in thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin and poly(ϵ‐caprolactone)

Thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin (PEG‐ER) and poly(?‐caprolactone) (PCL) were prepared via an in situ curing reaction of poly(ethylene glycol) diglycidyl ether (PEGDGE) and maleic anhydride (MAH) in the presence of PCL. The miscibility, phase behavior, crystallization, and morphology of these blends were investigated. The uncured PCL/PEGDGE blends were miscible, mainly because of the entropic contribution, as the molecular weight of PEGDGE was very low. The crystallization and melting behavior of both PCL and the poly(ethylene glycol) (PEG) segment of PEGDGE were less affected in the uncured PCL/PEGDGE blends because of the very close glass‐transition temperatures of PCL and PEGDGE. However, the cured PCL/PEG‐ER blends were immiscible and exhibited two separate glass transitions, as revealed by differential scanning calorimetry and dynamic mechanical analysis. There existed two phases in the cured PCL/PEG‐ER blends, that is, a PCL‐rich phase and a PEG‐ER crosslinked phase composed of an MAH‐cured PEGDGE network. The crystallization of PCL was slightly enhanced in the cured blends because of the phase‐separated nature; meanwhile, the PEG segment was highly restricted in the crosslinked network and was noncrystallizable in the cured blends. The phase structure and morphology of the cured PCL/PEG‐ER blends were examined with scanning electron microscopy; a variety of phase morphologies were observed that depended on the blend composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2833–2843, 2004     

Reaction‐induced phase separation in epoxy/polysulfone/poly(ether imide) systems. II. Generated morphologies

Epoxy–aromatic diamine formulations are simultaneously modified with two immiscible thermoplastics (TPs), poly(ether imide) (PEI) and polysulfone (PSF), in concentrations ranging from 5 to 15 wt %. The epoxy monomer is based on diglycidyl ether of bisphenol A and the aromatic diamines (ADs) are either 4,4′‐diaminodiphenylsulfone (DDS) or 4,4′‐methylenebis(3‐chloro 2,6‐diethylaniline) (MCDEA). Using phase diagrams developed in Part I of this series, thermal cycles are selected to generate different morphologies. It is found that, whatever the AD employed, a particulate morphology is obtained when curing blends that are initially homogeneous. In the case of DDS‐cured blends, a unimodal particle size distribution of PSF and PEI dispersed in a continuous epoxy‐rich phase is observed. By contrast, the MCDEA‐cured blends show a bimodal particle size distribution for all PSF/PEI relations that are analyzed. A completely different morphology, characterized by a distribution of irregular TP‐rich domains dispersed in an epoxy‐rich phase (double phase morphology), is obtained when curing blends that are initially immiscible. An X‐ray analysis of the different phases makes it possible to determine their qualitative composition. The dynamic mechanical behavior of fully cured blends is also discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3964–3975, 2004     

环氧树脂共混物相结构的调控方法研究

研究了环氧树脂(E51)/聚砜(PSF)共混物相结构的控制方法.通过抑制相分离、控制预固化的反应程度控制环氧树脂的分子量,固化后可获得不同的共混物相结构.依据红外测定的固化反应程度设定固化程序,可有效控制共混物的相结构.加入促进剂三氟化硼-乙基胺(BTF-EA)可提高固化反应速度,使相分离结构在早期被抑制,以获得小微区的相结构.     

Influence of carboxyl‐terminated (butadiene‐co‐acrylonitrile) loading on the mechanical and thermal properties of cured epoxy blends

A mixture of epoxy with liquid nitrile rubber, carboxyl‐terminated (butadiene‐co‐acrylonitrile) (CTBN) was cured under various temperatures. The cured resin was a two‐phase system, where spherical rubber domains were dispersed in the matrix of epoxy. The morphology development during cure was investigated by scanning electron microscope (SEM). There was slight reduction in the glass transition temperature of the epoxy matrix (T_g) on the addition of CTBN. It was observed that, for a particular CTBN content, T_g was found to be unaffected by the cure temperature. Bimodal distribution of particles was noted by SEM analysis. The increase in the size of rubber domains with CTBN content is due probably to the coalescence of the rubber particles. The mechanical properties of the cured resin were thoroughly investigated. Although there was a slight reduction in tensile strength and young's modulus, appreciable improvements in impact strength, fracture energy, and fracture toughness were observed. Addition of nitrile rubber above 20 parts per hundred parts of resin (phr) made the epoxy network more flexible. The volume fraction of dispersed rubbery phase and interfacial area were increased with the addition of more CTBN. A two‐phase morphology was further established by dynamic mechanical analysis (DMA). © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2531–2544, 2004     

THE EFFECT OF BLENDING SEQUENCE ON PHASE MORPHOLOGY OF NYLON 6/ABS/SMA BLENDS

The preparation process-dependent phase morphology of blends composed of nylon 6 and acrylonitrile-butadiene- styrene(ABS)over a composition range of 30-70 wt% using a styrene-maleic anhydride(SMA)copolymer as the compatibilizing agent with a constant content(5phr)was investigated.The results of the scanning electron microscope (SEM)observation revealed that compared with the binary blends of nylon 6 and ABS,the existence of SMA caused a composition shift of phase inversion to a higher weight fraction of...     

Synthesis and curing of liquid crystalline epoxy resin based on naphthalene mesogen

Aromatic liquid crystalline epoxy resin (LCE) based on naphthalene mesogen was synthesized and cured with aromatic diamines to prepare heat‐resistant LCE networks. Diaminodiphenylester (DDE) and diaminodiphenylsulfone (DDS) were used as curing agents. The curing reaction and liquid crystalline phase of LCE were monitored, and mechanical and thermal properties of cured LCE network were also investigated. Curing and postcuring peaks were observed in dynamic DSC thermogram. LCE network cured with DDE displayed liquid crystalline phase in the curing temperature range between 183 and 260°C, while that cured with DDS formed one between 182 and 230°C. Glass transition temperature of cured LCE network was above 240°C, and crosslinked network was thermally stable up to 330°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 419–425, 1999     

聚酰亚胺对多官能团环氧树脂的增韧作用

本文选择不同比例的聚酰亚胺(PEI)与多官能团的环氧树脂(MY0510)和 NovoIak 树脂(DEN431)共混,以3,3′—二氨基二苯亚砜(DDS)为固化剂,制备一系列的共混物样品。通过三点弯曲试验、扫描电镜和动态力学热分析分别测定共混物的应力强度因子(K_(1c))和临界应变能松驰速率(G_(1c))、形态结构和玻璃化转变温度。当加入 PEI 时,共混物的 K_(1C)和 G_(1C)都有显著的提高,即增加了环氧树脂的韧性。虽然所有共混物只有一个Tg 峰,但电镜的观察结果说明为两相结构。当 PEI 的含量为10%时,PEI 开始从分散相转变为连续相。后固化作用使 Tg 提高了6—20℃,同时也有利于 K_(1C)和 G_(1C)。     

PVT behavior of thermoplastic poly(styrene-co-acrylonitrile)-modified epoxy systems: relating polymerization-induced viscoelastic phase separation with the cure shrinkage performance

The volume shrinkage during polymerization of a thermoplastic modified epoxy resin undergoing a simultaneous viscoelastic phase separation was investigated for the first time by means of pressure-volume-temperature (PVT) analysis. Varying amounts (0-20%) of poly(styrene-co-acrylonitrile) (SAN) have been incorporated into a high-temperature epoxy-diamine system, diglycidyl ether of bisphenol A (DGEBA)-4,4'-diaminodiphenyl sulfone (DDS) mixture, and subsequently polymerized isothermally at a constant pressure of 10 MPa. Volume shrinkage is highest for the double-phased network-like bicontinuous morphology in the SAN-15% system. Investigation of the epoxy reaction kinetics based on the conversions derived from PVT data established a phase-separation effect on the volume shrinkage behavior in these blends. From subsequent thermal transition studies of various epoxy-DDS/SAN systems, it has been suggested that the behavior of the highly intermixed thermoplastic SAN-rich phase is the key for in situ shrinkage control. Various microscopic characterizations including scanning electron microscopy, atomic force microscopy, and optical microscopy are combined to confirm that the shrinkage behavior is manipulated by a volume shrinkage of the thermoplastic SAN-rich phase undergoing a viscoelastic phase separation during cure. Consequently, a new mechanism for volume shrinkage has been visualized for the in situ polymerization of a thermoplastic-modified epoxy resin.     

Development and characterization of thermosetting-thermoplastic polymer blends for applications in damage-tolerant composites

Compatibility or miscibility of polyethersulfones (ICI: Victrex 100P and 300P) and a tetrafunctional epoxy (Ciba-Geigy: MY-720), cured with an aromatic anhydride, has been studied using scanning electron microscopy, x-ray microanalysis, and dynamic mechanical spectroscopy. Fracture toughness of epoxy and blends of an epoxy and polyethersulfones has been measured using three-point bend tests (ASTM: E-399–81), and the energy release rate (G_IC) for the three materials has been compared as a function of test temperature. Fracture surfaces were examined by x-ray microanalysis for detecting concentration of sulfur, present in polyethersulfones, in the matrix and precipitated phase. The influence of morphology of epoxy/polyethersulfone blends on its fracture toughness and toughening mechanism has been studied. A toughening criterion is proposed.     

高性能环氧树脂/碳纳米管复合物的热分析研究

用差示扫描量热仪(DSC)、热失重分析仪(TGA)和动态力学热分析仪(DMTA)研究了多壁碳纳米管(MWNTs)/高性能4,4′-二氨基二苯甲烷四缩水甘油环氧树脂(TGDDM)/4,4′-二氨基二苯基砜(DDS)复合物的热性能.Kissinger和Flynn-Wall-Ozawa的非等温固化动力学研究发现,随着MWNTs含量的增加,复合物固化反应的活化能先减小后增大.TGA研究表明,MWNTs的添加对环氧树脂热稳定性影响很小.碳纳米管填充到TGDDM/DDS体系后,复合物的储存模量随着MWNTs含量的增加而增大,而玻璃化温度却随之减小.     

Crystallization behavior of dynamically cured polypropylene/epoxy blends

Dynamically cured polypropylene (PP)/epoxy blends compatibilized with maleic anhydride grafted PP were prepared by the curing of an epoxy resin during melt mixing with molten PP. The morphology and crystallization behavior of dynamically cured PP/epoxy blends were studied with scanning electron microscopy, differential scanning calorimetry, and polarized optical microscopy. Dynamically cured PP/epoxy blends, with the structure of epoxy particles finely dispersed in the PP matrix, were obtained, and the average diameter of the particles slightly increased with increasing epoxy resin content. In a study of the nonisothermal crystallization of PP and PP/epoxy blends, crystallization parameter analysis showed that epoxy particles could act as effective nucleating agents, accelerating the crystallization of the PP component in the PP/epoxy blends. The isothermal crystallization kinetics of PP and dynamically cured PP/epoxy blends were described by the Avrami equation. The results showed that the Avrami exponent of PP in the blends was higher than that of PP, and the crystallization rate was faster than that of PP. However, the crystallization rate decreased when the epoxy resin content was greater than 20 wt %. The crystallization thermodynamics of PP and dynamically cured PP/epoxy blends were studied according to the Hoffman theory. The chain folding energy for PP crystallization in dynamically cured PP/epoxy blends decreased with increasing epoxy resin content, and the minimum of the chain folding energy was observed at a 20 wt % epoxy resin content. The size of the PP spherulites in the blends was obviously smaller than that of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1181–1191, 2004     

Effect of crosslinking on intermolecular interactions in thermosetting blends of epoxy resin with poly(ethylene oxide)

The miscibility and intermolecular-specific interactions in thermosetting blends of epoxy resin (ER) with poly(ethylene oxide) (PEO) cured with various amounts of 1,3,5-tridroxybenzene (THB) were investigated by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). The glass-transition behavior indicated that all the blends were miscible and had homogeneous amorphous phases; FTIR showed that there were the intermolecular hydrogen-bonding interactions between crosslinked ER and PEO. However, both the glass-transition behavior and infrared spectroscopy also indicated that the intermolecular interactions were significantly reduced by the formation of crosslinked structures, which was shown by comparing the experimental results of poly(hydroxyether of bisphenol A) (PH)/PEO and ER/PEO blends cured with various amounts of the curing agent. In ER/PEO blends the intermolecular hydrogen-bonding interactions were much weaker than the self-association of hydroxyls of ER, which was in marked contrast to the interactions in PH/PEO blends. In ER/PEO blends with various amounts of the curing agent, the intermolecular interactions between epoxy polymers and PEO were reduced with an increasing degree of crosslinking. The results were interpreted in terms of the effect of crosslinking on the intermolecular interactions, such as steric shielding, the screening effect, and chain connectivity resulting from the formation of the three-dimensional crosslinked network, which could reduce the intermolecular hydrogen-bonding interactions among hydroxyls of ER versus ether oxygen atoms of PEO. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2567–2575, 2004     

Impact modification of thermoplastics by methyl methacrylate and styrene-grafted natural rubber latexes

The preparation and characterization of polymer blends with structured natural rubber (NR)-based latex particles are presented. By a semicontinuous emulsion polymerization process, a natural rubber latex (prevulcanized or not) was coated with a shell of crosslinked polymethylmethacrylate (PMMA) or polystyrene (PS). Furthermore, core–shell latexes based on a natural rubber/crosslinked PS latex semi-interpenetrating network were synthesized in a batch process. These structured particles were incorporated as impact modifiers into a brittle polymer matrix using a Werner & Pfleiderer twin screw extruder. The mechanical properties of PS and PMMA blends with a series of the prepared latexes were investigated. In the case of PMMA blends, relatively simple core (NR)–shell (crosslinked PMMA) particles improved the mechanical properties of PMMA most effectively. An intermediate PS layer between the core and the shell or a natural rubber core with PS subinclusions allowed the E-modulus to be adjusted. The situation was different with the PS blends. Only core–shell particles based on NR-crosslinked PS latex semi-interpenetrating networks could effectively toughen PS. It appears that microdomains in the rubber phase allowed a modification of the crazing behavior. These inclusions were observed inside the NR particles by transmission electron microscopy. Transmission electron photomicrographs of PS and PMMA blends also revealed intact and well-dispersed particles. Scanning electron microscopy of fracture surfaces allowed us to distinguish PS blends reinforced with latex semi-interpenetrating network-based particles from blends with all other types of particles.     

Synthesis of submicron-sized peanut-shaped poly(methyl methacrylate)/polystyrene particles by seeded soap-free emulsion polymerization

Submicron-sized peanut-shaped poly(methyl methacrylate)/polystyrene(PMMA/PS) particles were successfully synthesized by seeded soap-free emulsion polymerization of styrene on the spherical crosslinked PMMA seed particles.The obtained peanut-shaped particles showed a novel internal morphology:PS phase formed one domain which linked to the other domain having PMMA core encased by PS shell.     

热塑性聚醚酰亚胺改性四官能度环氧树脂的相分离研究──固化剂用量的影响

以DSC、TRLS和SEM等方法研究了固化剂DDS用量对苯端基聚醚酰亚胺(P-PEI)改性4,4'-二氨基二苯甲烷四缩水甘油环氧树脂(TGDDM)体系的固化速率及相结构的影响.结果表明,20phrP-PEI改性环氧体系在150℃固化时,随DDS量增加,固化反应速率增大,相分离时间提前,形成了不同的相结构,解释了DDS量对粘接剪切强度的影响.     

Synthesis and characterisation of epoxy-novolac/bismaleimide networks

Epoxy-novolac resin was modified with 1,1^′-(methylenedi-4,1-phenylene) bismaleimide (BMI), and cured with an aromatic amine. Cure behaviour of these blends was studied using differential scanning calorimetry (DSC). The thermograms indicated a unimodal exothermic peak for blends containing lower percentage of BMI. The cured blends showed much higher glass transition temperatures than that of the unmodified epoxy. Thermal stability of the cured epoxy resin was also improved with BMI addition. A homogeneous structure (with no phase separation) of the blends was confirmed both by DSC analysis and scanning electron microscopy (SEM).