相干检测定向系统探测误差研究

分析了探测系统中存在的高斯白噪音和激光器相位噪音的统计特性,研究它们对探测系统性能的影响.计算结果表明只要维持足够低的激光器相位噪音就能实现高准确度的光束定向.     

Eye-safe radiation source based on an optical parametric oscillator

We have studied an optical parametric oscillator (OPO) with an unstable telescopic cavity, placed inside the cavity of an actively Q-switched multimode Nd³⁺:KGW pump laser. We used a KTP crystal as the nonlinear medium for the OPO. We have compared the emission characteristics of OPOs with unstable telescopic and planar cavities. We have established that compared with the planar cavity, the unstable cavity reduces the OPO beam divergence and improves the spatial distribution of the radiation energy in the far wave zone. Based on our investigations, we have designed a compact eye-safe (λ = 1.578 μm) laser source with natural cooling, emitting (for electrical pumping energy 7.3 J) pulses with pulse energy 22 mJ and pulse duration 6 nsec. The FWHM beam divergence for the source is no greater than 3.5 mrad. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 73, No. 2, pp. 254–259, March–April, 2006.     

Observation of the dynamic Stark effect at microwave frequencies in a molecular beam maser

Multiplet splitting of the main doublet of the ¹⁴NH₃, J = K = 1 inversion line has been observed in a molecular beam maser spectrometer when a strong microwave radiation field is introduced into the maser cavity. This phenomenon is attributed to the dynamic Stark effect at microwave frequencies.     

Photonic crystal fiber for fundamental mode operation of multicore fiber lasers and amplifiers

A mode-selection method based on a single-mode photonic crystal fiber (PCF) in the multicore fiber (MCF) lasers is presented. The designed PCF has a central core region formed by a missing air-hole, and three air-hole rings. With an appropriate choice of the design parameters of the PCF, the power coupling between the fundamental mode (FM) of the PCF and the fundamental MCF mode can be much higher than those between the FM and the other supermodes. As a result, the fundamental MCF mode has the maximum power reflection coefficient on the right-hand side of the MCF laser cavity, and dominates the output laser power. Since the maximum power of the fundamental MCF mode will lead to the desired laser beam profile, higher the fraction of the fundamental MCF mode power contained in the total output power contributes to higher beam quality. The numerical simulations show that the effectiveness of the fundamental MCF mode-selection is higher in the MCF lasers with the PCF as a mode-selection component than in the MCF lasers based on the free-space Talbot cavity method. Additionally, for the MCF amplifiers, an approach is presented to decrease the sensitivity of the amplifier performance to the variation of Gaussian beam waist utilizing the coupling between the Gaussian beam and the FM of the PCF. The numerical results show that this method can effectively increase the design flexibility for a broad range of the Gaussian beam waist.     

Laser beam patterns of an optical cavity formed by two twisted cylindrical mirrors

Propagation of an elliptical Gaussian beam in a multiple-pass optical cell formed by two twisted cylindrical mirrors has been described by means of complex curvature tensors. Using the ABCD tensor approach various light patterns were computed for the use in tunable laser absorption spectroscopy with a multiple-pass optical cell. Light patterns with high beam-spot density can be also defined for a cavity formed by two twisted cylindrical high-reflectivity mirrors. In order to achieve higher cavity output intensity, a high-reflectivity cylindrical mirror cavity with at least one mirror that has a central transparent spot for laser beam injection has been described for applications in non-resonant cavity enhanced absorption spectroscopy. The author was with TDL Sensors Ltd., when the experimental part of this work was performed.     

Broad-area diode-laser system for a rubidium Bose-Einstein condensation experiment

We report on master-oscillator power amplification using a broad-area laser diode (BAL) emitting at a wavelength of λ =780 nm. The master oscillator is an injection-locked single-mode diode laser delivering a seeding beam of 35 mW, which is amplified in double pass through the BAL up to 410 mW. After beam shaping and spatial filtering by a single-mode fibre we obtain a clean Gaussian beam with a maximum power of 160 mW. There is no detectable contribution of the BAL eigenmodes in the spectrum of the output light. This laser system is employed for operation of a ⁸⁷Rb magneto-optical trap (MOT) and for near-resonant absorption imaging in a Bose-Einstein condensation experiment. Received: 10 April 2000 / Revised version: 13 June 2000 / Published online: 2 August 2000     

L波段强流单束团注入器的束流动力学计算

自由电子激光器要求高亮度、低能散度的电子束注入波荡器(Undulator)。本文叙述提供高亮度电子束的高频电子直线加速器中的注入器部分的设计计算。注入器由L波段(1300MHz)的十二分频和三分频两个谐振腔预聚束器和一个基波频率的变相速聚束器组成。粒子运动方程中考虑了空间电荷效应和束流负载效应。电子枪的注入参数:脉冲宽度T=4ns;电流I=5A;电子的初始动能E_0=100keV;电子束分布为高斯型。参数优化设计结果:单束团宽度小于25ps,峰值电流达400A以上,电子的平均归一化能量>4,束团内的能量差小于200keV。     

高斯光束与谐振腔基模模式光路谐振匹配的分析与校准

为了降低高斯光束与谐振腔耦合过程中失调量和失配量对基于无源谐振腔测量技术精度的影响, 采用高斯光束变换规律、模式耦合有关理论以及光束传播坐标变换等相关理论, 就失调量和失配量对基模耦合效率的影响分别进行分析和模拟, 并据此给出了一般情况下两个参考量同时存在时基模耦合效率的表达式. 分析表明: 失配量的存在主要影响激光器与谐振腔的耦合效率, 而对高阶模式的激发影响较小, 因此对谐振腔的衰减线型影响较小; 失调量的存在对谐振腔高阶模式的激发起主要作用, 给测量带来严重误差. 该结论为利用腔出射光信号来确定误调参量值的实验方案提供了依据. 因此, 在考虑光源光谱线宽的情况下, 就光源光谱线宽的特性提出两种装调校准方案: 基于法布里-珀罗干涉仪法和基于多维象限探测器探测谐振腔出射光的调节回路, 这将为分析基于无源谐振腔的相关技术测量误差来源以及实现测量系统的高精度装调提供理论指导.     

Development of injection-seeded, pulsed optical parametric generator/oscillator systems for high-resolution spectroscopy

We report the development and application of pulsed optical parametric generator (OPG) and optical parametric oscillator (OPO) systems that are injection seeded with near-infrared distributed feedback diode lasers. The OPG is injection seeded at the idler wavelength without the use of a resonant cavity. Two counter-rotating, beta-barium-borate (β-BBO) crystals are used in the OPG. These crystals are pumped by the third harmonic, 355-nm output of an injection-seeded Nd:YAG laser. An OPO version of the system has also been developed by placing two flat mirrors around the two β-BBO crystals to form a feedback cavity at the signal wavelength. The OPO cavity length is not actively controlled. The output signal beam from the OPG or OPO is amplified using an optical parametric amplifier (OPA) stage with four β-BBO crystals. The frequency bandwidths of the signal and idler laser radiation from OPG/OPA and OPO/OPA systems have been determined to be slightly greater than 200 MHz. The temporal pulses from each system are smooth and near-Gaussian. High-resolution optical absorption measurements of acetylene (C₂H₂) were performed as another check of the frequency spectrum of the idler beam. The frequency-doubled signal output of the OPO/OPA system was used to perform high-resolution, single-photon, laser-induced fluorescence (LIF) spectroscopic studies of the (0,0) vibrational band of the A ²Σ⁺−X ²Π electronic transition of nitric oxide (NO) at low pressure. Excellent agreement was obtained between the theory and the experiment. The signal output of the OPG/OPA system was also used for sub-Doppler, two-photon LIF spectroscopic studies of the same vibration–rotation manifold of NO.This revised version was published online in August 2005 with a corrected cover date.     

Experimental investigation and numerical simulation of the spatio-temporal dynamics of nanosecond pulses in Q-switched Nd:YAG lasers

This paper reports on an experimental investigation and numerical simulation of the spatio-temporal dynamics of the pulse formation in flashlamp-pumped Q-switched Nd:YAG lasers. The temporal evolution of the spatial intensity distribution is measured with a fast two-dimensional CCD camera. The measurements are performed for two lasers with different cavity configurations. A laser with an optically stable resonator and an internal mode aperture generated pulses with a spatial intensity distribution which is Gaussian at all times during the 10-ns-long pulse. During the pulse evolution the value of the beam-quality factor M²remains below 1.3. In a laser with a positive-branch unstable resonator the laser pulse also starts with a Gaussian intensity distribution, but becomes rapidly non-Gaussian. The corresponding M²values increase from about 1 at the beginning of the formation of the pulse to more than 12 in the tail of the pulse. The measurements are compared with the results of a numerical simulation which takes the laser amplification, the properties of the laser cavity, and the diffraction of the beam in the laser cavity into account. The spatio-temporal dynamics of the pulse formation predicted by the numerical model are in good agreement with the experimental results.PACS 42.60.Jf     

光束在尾流气泡中传输的复散射效应

为了了解光束在尾流气泡中的传输特性,为前向光尾流的探测提供理论依据,研究了光束在尾流中传输时传播方向上和横截面方向上的辐射强度分布特性.基于辐射传输方程的小角度近似解,得到了探测截面上的约化强度和漫射强度的表达式,其中漫射强度表征了复散射的强弱;针对典型的尾流气泡分布,通过数值计算分析了光束传输方向上的约化强度和漫射强度与接收视场角、光学厚度和光束大小的关系,也计算分析了光束横截面方向上的辐射强度随光束大小和横向距离的变化关系.结果表明,光束在尾流气泡中传输时复散射效应明显,且复散射的强弱与接收视场角、光束直径、光学厚度和横向距离密切相关.     

Calculation of the Spatio-Temporal Dynamics of Q-switched Yb^3＋：YAG Laser with an Unstable Cavity and a Super-Gaussian Mirror

A numerical simulation used to compute the spatio-temporal dynamics of pulse formation of diode-pumped Q- switched Yb： YA G laser is carried out. The model takes the laser amplification and gain saturation, the properties of the laser cavity, and the diffractive effects of the laser disc into account. The numerical calculation is performed for a confocal positive-branch unstable resonator with a super Gaussian coupling mirror. The simulation results show that the laser pulse starts from a Gaussian intensity distribution and becomes rapidly non-Gaussian. The corresponding beam quality M^2 factor is seen to vary approximately from 1.5 at the beginning of the formation of pulse to more than 10 in the tail of the pulse, with a value of 11.6 at the peak of the pulse.     

Quantitative analysis of dilute mixtures of SO<Subscript>2</Subscript> in N<Subscript>2</Subscript> at 7.4 μm by difference frequency spectroscopy

We describe a 7.4-μm source based on difference frequency generation with 6.5 mW of 1278-nm radiation from an extended cavity laser and 66 mW of 1544-nm radiation from another extended cavity laser, amplified in an erbium-doped fibre amplifier. Optimum focusing of the input beams in the 5×5×10-mm³ AgGaSe₂ crystal, and the spatial and temporal characteristics of the output beam, are determined. The source is used for accurate determination of line parameters for selected lines of the ν₃ band of SO₂, centred at 1361 cm^-1. Subsequently, these lines are used for performing quantitative analysis of gas mixtures containing SO₂ at concentration levels down to 4 ppm without relying on any calibration with certified gas mixtures. This demonstrates the potential of infrared spectroscopy as a primary method for low-concentration gas analysis. Received: 16 January 2003 / Revised version: 19 February 2003 / Published online: 9 April 2003 RID="*" ID="*"Corresponding author. Fax: +45-4593/1137, E-mail: jh@dfm.dtu.dk     

Scattering of CO2 laser beam by a plasma of air breakdown at pressures of 1–300 torr

Results from experiments with a TEA CO₂ laser with an unstable cavity and a power of 10⁷ W are presented. Laser radiation was focused by a lens with a focal length of 100 or 150 mm in air free of dust (grains larger than 0.1 μm were filtered out). The power and energy of radiation scattered within a central cone of an annular laser beam was recorded. The dependences of the threshold (for scattering) laser power and the scattered power on pressure were determined. The angular divergence of the collimated scattered beam was found to be 3.9 mrad, which was close to the divergence of the laser beam (2.5 mrad). The amplification of the scattered radiation pulse was performed.     

Propagation factors of Hermite–Gaussian beams in turbulent atmosphere

Based on the extended Huygens–Fresnel integral and the second-order moments of the Wigner distribution function, an analytical formulae for the propagation factors (M²-factors) of coherent and partially coherent one-dimensional Hermite–Gaussian beams in a turbulent atmosphere are derived. Evolution properties of the M²-factor of the Hermite–Gaussian beam in a turbulent atmosphere are studied numerically in detail. Our results show that the M²-factor of the Hermite–Gaussian beam increases upon propagation in a turbulent atmosphere. The M²-factor of the Hermite–Gaussian beam with larger beam order (or lower coherence) increases slower that of the Hermite–Gaussian beam with smaller beam order (or higher coherence) in a turbulent atmosphere, which means that the Hermite–Gaussian beam with a larger beam order and lower coherence is less affected by a turbulent atmosphere. Our results will be useful in long-distance free-space optical communications.     

计算电容中Fabry-Perot干涉仪测量位移的相位修正方法

计算电容是复现电学阻抗单位的基准装置, 利用计算电容值和量子霍尔电阻值可以准确计算出精细结构常数α. 计算电容的本质是通过高准确度地测量屏蔽电极的位移, 实现对电容量值的测量. 因此, 基于Fabry-Perot干涉仪的精密电极位移测量系统是计算电容装置中最为核心和关键的部分. 在Fabry-Perot干涉仪测位移过程中, 由于高斯激光束存在轴向Gouy相位, 该附加相位将会引起相邻干涉条纹对应位移的变化(大于或者小于λ/2), 导致位移的测量值与实际值存在偏差. 本文阐述了高斯激光场的传播特性, 利用高斯激光束在自由空间和透过薄透镜复振幅的变换关系, 建立了计算电容装置中Fabry-Perot干涉仪透射光束的传输模型; 通过对不同腔长的Fabry-Perot干涉仪透射光场相位的分析, 获得了高斯激光束轴向Gouy相位修正与传输距离的关系. 结果表明, 当腔长从111.3 mm移动至316.3 mm时, 在接收距离为560 mm的情况下, 高斯光束轴向Gouy 相位引起的位移修正的绝对值最小为0.7 nm, 其相对相位修正量|δL|/|ΔL| = 3.4×10^-9.     

Comparative studies of eye-safe intracavity and extracavity optical parametric oscillators with an unstable telescopic cavity

We have experimentally studied the lasing characteristics of an eye-safe optical parametric oscillator (OPO) with an unstable telescopic cavity when it is placed inside (intracavity OPO) and outside (extracavity OPO) the plane-parallel cavity of a pulsed, nearly single-mode KGW:Nd pump laser. We used a KTP crystal as the nonlinear medium for the OPO. We have shown that the intracavity OPO has the higher lasing efficiency. We have observed that the distribution of nonlinear losses introduced by the intracavity OPO, nonuniform over the cavity cross section, leads to an increase in the diameter and divergence of the radiation beam from the pump laser and a dependence of its temporal lasing dynamics on the transverse beam coordinate. We propose a physical model qualitatively explaining the spatial and temporal lasing dynamics of a radiation source with an intracavity OPO. Both OPO versions generate beams of radiation with about the same divergence. When the KGW:Nd laser has an electrical pumping energy of 7.3 J and a cavity length of 77 cm, the intracavity OPO and the extracavity OPO emit pulses with energies of 14.5 mJ and 12.0 mJ and duration 18 nsec and 13 nsec respectively. The divergence of the eye-safe radiation (λ = 1.578 μm) at 86.5% of the total pulse energy is no greater than 5.5 mrad for an OPO output beam diameter of = 2 mm. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 73, No. 4, pp. 535–543, July–August, 2006.     

Near-UV sub-Doppler spectroscopy on a metastable Mg beam by a frequency-doubled diode laser

Near-UV radiation is generated by doubling the frequency of a semiconductor laser in a nonlinear crystal. The crystal is contained in a resonant cavity in order to improve the conversion efficiency. The cavity increases the efficiency by about three orders of magnitude. This radiation has been used to perform spectroscopy of metastable magnesium in an atomic beam. We observed the (3s3p)³ P–(3s3d)³ D transition multiplet, which is of interest for metrological applications. The isotopic shift between²⁴Mg and²⁶Mg was measured and new information on the hyperfine structure of²⁵Mg was obtained. This radiation source is promising also in order to improve the Mg frequency standard.     

Influence of turbulence on the beam propagation factor of Gaussian Schell-model array beams

The analytical expression for the beam propagation factor (M²-factor) of Gaussian Schell-model (GSM) array beams propagating through atmospheric turbulence is derived. It is shown that the M²-factor of GSM array beams depends on the beam number, the relative beam separation distance, the beam coherence parameter, the type of beam superposition, and the strength of turbulence. The turbulence results in an increase of the M²-factor. However, for the superposition of the intensity the M²-factor is less sensitive to turbulence than that for the superposition of the cross-spectral density function. The M²-factor of GSM array beams is larger than that of the corresponding Gaussian array beams. However, the M²-factor of GSM array beams is less affected by turbulence than that of the corresponding Gaussian array beams. For the superposition of the cross-spectral density function a minimum of the M²-factor of GSM array beams may appear in turbulence, which is even smaller than that of the corresponding single GSM beams.     

Performance Test of CW 300?GHz Gyrotron FU CW I

A 300 GHz CW gyrotron FU CW I has been developed and installed in the Research Center for Development of Far-Infrared Region, University of Fukui as a power source of a high frequency material processing system. Its performance was tested and the maximum power of 1.75 kW / CW has been attained at the beam voltage of 15 kV and the beam current of 1A. The maximum window power efficiency of 15.5% has been obtained at the cathode voltage slightly lower than 15 kV. This gyrotron is designed to deliver a Gaussian beam after mode conversion from the oscillation mode TE_22,8 in the cavity with a complex of an internal radiator and beam shaping mirrors. The detailed measurement with an infrared camera has confirmed that a Gaussian beam is radiated when the magnetic field strength B _c at the cavity is adjusted at a proper value. However, within a range of B _c , the output power is emerged into multiple directions, which suggests simultaneous oscillation of competing cavity modes.