Effect of pH on Competitive Adsorption of Cu(II), Ni(II), and Zn(II) from Water onto Chitosan Beads

The amounts of adsorption of Cu²⁺, Ni²⁺, and Zn²⁺ from single, binary, and tertiary nitrate solutions onto glutaraldehyde cross-linked chitosan beads were measured. The beads had an average particle size and pore volume of 2 mm and 0.06 cm³/g, respectively, and had a BET surface area of 60 m²/g. All experiments were performed at 298 K as a function of initial pH (2.0–5.0), total metal concentration (0.77–17.0 mol/m³), and molar concentration ratio (0.25–4) in the aqueous phase. It was shown that the amount of metal adsorption generally increased with increasing solution pH. Competitive adsorption was significant in binary and tertiary systems when Cu²⁺ was present. The selectivity factor reached maximum in an equilibrium pH range of 5.1–5.3 and 4.5–4.9 for the Cu-Ni and Cu-Zn binary systems, respectively. This adsorbent provided a possibility for selective separation of Cu²⁺ from such multi-component solutions.     

Adsorption of Pb(II) and Ni(II) From Aqueous Solution by a High-Capacity Industrial Sewage Sludge-Based Adsorbent

In the present study, adsorption of Ni(II) and Pb(II) from aqueous solution was investigated using activated carbon synthesized with industrial wastewater sludge. The synthesized adsorbent was analyzed using nitrogen adsorption–desorption and Fourier transfer infrared (FTIR) techniques. Batch adsorption mode was used to evaluate the effect of solution pH, contact time, adsorbent dose, initial metal ion concentration, and temperature on the adsorption capacity of the synthesized adsorbent. The kinetic data were analyzed using different kinetic models. The pseudo-second-order equation gave the best fit to the experimental data for both metal ions. The equilibrium isotherm data were analyzed using the Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) isotherm models. The results showed that the data obtained for the Ni(II) and Pb(II) adsorption are in good agreement with the Langmuir model. The Langmuir mono-layer maximum adsorption capacities for Ni(II) and Pb(II) ions were estimated to be 74.06 and 88.76 mg g^?1 at 25°C, respectively. In addition, the thermodynamic studies proved that the adsorption process of both metals could be considered endothermic.     

交联壳聚糖树脂对Ni(II)的吸附行为研究

研究了甲醛、环氧氯丙烷交联壳聚糖树脂(AECTS)对Ni(II)的吸附行为和吸附Ni(II)对树脂结构及性能的影响.用FTIR,WAXD,TGA和DSC对吸附产物进行了结构表征,并深入分析了AECTS与Ni(II)之间的作用机理.结果表明:AECTS主要以配位形式吸附Ni(II);AECTS吸附Ni(II)后,结晶度下降、总体上热稳定性变差;Ni(II)对AECTS的主链分解具有明显的催化功能,而空气气氛中对AECTS在500℃附近的分解表现出火焰缓蚀作用.AECTS对Ni(II)的吸附行为符合Langmuir模型,属于单分子层吸附,所有吸附位对Ni(II)的作用近似相同;与壳聚糖(CTS)比较,造成AECTS对Ni(II)吸附量增大的主要原因是AECTS结晶度下降和孔隙率增加,二者导致在交联处理前Ni(II)难于接近的吸附位点“活性”相对增大,使其更容易与Ni(II)相结合;不同介质对AECTS吸附Ni(II)的影响大小顺序为HCl>CdCl2>MgCl2>NaCl,前两者使吸附量减小,MgCl2使吸附量稍有增加,NaCl对吸附量基本没有影响.     

交联壳聚糖树脂对Ni(II)的吸附行为研究

研究了甲醛、环氧氯丙烷交联壳聚糖树脂(AECTS)对Ni(II)的吸附行为和吸附Ni(II)对树脂结构及性能的影响. 用FTIR, WAXD, TGA和DSC对吸附产物进行了结构表征, 并深入分析了AECTS与Ni(II)之间的作用机理. 结果表明: AECTS主要以配位形式吸附Ni(II); AECTS吸附Ni(II)后, 结晶度下降、总体上热稳定性变差; Ni(II)对AECTS的主链分解具有明显的催化功能, 而空气气氛中对AECTS在500 ℃附近的分解表现出火焰缓蚀作用. AECTS对Ni(II)的吸附行为符合Langmuir模型, 属于单分子层吸附, 所有吸附位对Ni(II)的作用近似相同; 与壳聚糖(CTS)比较, 造成AECTS对Ni(II)吸附量增大的主要原因是AECTS结晶度下降和孔隙率增加, 二者导致在交联处理前Ni(II)难于接近的吸附位点“活性”相对增大, 使其更容易与Ni(II)相结合; 不同介质对AECTS吸附Ni(II)的影响大小顺序为HCl＞CdCl₂＞MgCl₂＞NaCl, 前两者使吸附量减小, MgCl₂使吸附量稍有增加, NaCl对吸附量基本没有影响.     

3-N-乙酰基-2-取代芳基-5-[5''-甲基-异噁唑-3'']-Δ3-1,3,4－噁唑啉类化合物的合成

保护氨基的壳聚糖微球经环氧氯丙烷交联得到不溶于酸的吸附剂，与氯乙酸在碱性条件下反应，合成了羧甲基壳聚糖树脂，并用FT-IR对树脂进行了表征。其吸附Pb^2 的实验结果表明，在1h内有最快的吸附速率，吸附受pH值影响。在pH=5时，对Pb^2 的吸附量为1．12mmol／g，比壳聚糖树脂提高了70％。     

Novel Mesoporous Organosilicas with Task Ionic Liquids: Properties and High Adsorption Performance for Pb(II)

Removal of toxic contaminants such as Pb(II) from waste solutions is environmentally requested. Therefore, in this paper, for potential novel sorbents, mesoporous ionic liquid-functionalized silicas were synthesized and tested for the removal of Pb(II) from aqueous solutions. The successful synthesis of the adsorbents was proved by nuclear magnetic resonance (²⁹Si and ¹³C NMR), Fourier transform infrared spectroscopy (FTIR), and elemental analysis. The structural and textural properties were determined using scanning electron microscopy (SEM), X-ray diffraction (XRD), high-resolution transmission electron microscopy (TEM), and low-temperature N₂ sorption, and the result showed that the applied procedure made it possible to obtain highly ordered particles with a two-dimensional mesostructure. The effects of several parameters including initial pH, contact time, adsorption temperature, and Pb(II) concentration were studied in detail and were discussed to evaluate the adsorption properties of the fabricated materials towards Pb(II). The obtained results confirmed a very high potential of the sorbents; however, the adsorption properties depend on the structure and amounts of the functional group onto fabricated materials. The sample ILS-Ox3-40 showed fast kinetics (equilibrium reached within 10 min) and capacity of 172 mg/g, and that makes it a promising sorbent for the cleanup of water contaminated by lead. It was also indicated that, regardless on structure of the tested materials, the Pb(II) removal was spontaneous and exothermic. The fabricated mesoporous silicas exhibited that they were easy to regenerate and had excellent reusability.     

Electrochemical Detection of Pb(II) by Glassy Carbon Electrode Modified with Amine-Functionalized Magnetite Nanoparticles

An amine-Fe₃O₄ modified glassy carbon (GC) electrode was constructed for detecting Pb(II) ions in wastewater. The electrode was characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Square wave anodic stripping voltammetry (SWASV) was used to detect the Pb(II), and the detection limit of Pb(II) was 0.15 µM. The sensitivity of the electrode to detect Pb(II) was about 10.07 µA/µM, with a correlation coefficient of 0.991, which was approximately 10 times bigger than that of a pure Fe₃O₄ modified electrode. The electrode also showed good selectivity and stability. This results indicated that the amine-magnetite material could have some potential applications in heavy metal ions detection in wastewater.     

Chemical modification of rose leaf with polypyrrole for the removal of Pb (II) and Cd (II) from aqueous solution

The rose leaf was successfully modified through coating with polypyrrole (PPy) in chemical oxidative route in order to remove Pb(II) and Cd(II) from aqueous media. The rose leaf/polypyrrole (RL/PPy) composites were characterized in terms of morphology, chemical structure, and conductivity properties. The spectrum were obtained from FTIR results which support the formation of RL/PPy composites. FTIR and SEM results indicate that the polypyrrole is completely covered on rose leaf. The conductivity of composite (1.8215 S/cm) was higher than polypyrrole (2.06 × 10^?3 S/cm). The metal removal studies were monitored by Ultraviolet Visible Absorption Spectrometer (UV-Vis). The optimum conditions were detected for adsorption by changing some experimental conditions (such as adsorbent dosage, contact time and stirring speed, initial concentration of the metal solutions and pH). Following the determination of the optimum conditions, the results of the metal removal from wastewater studies were performed by Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). Under the optimum conditions, the ICP-OES results obtained for waste water showed the useability of composite for the removal of Pb(II) and Cd(II). The Langmuir and Freundlich models are subjected to adsorption datas. The datas fitted better when by using Freundlich model.     

Bismuth-dispersed xerogel-based composite films for trace Pb(II) and Cd(II) voltammetric determination

We report for the first time the synthesis of bismuth-modified (3-mercaptopropyl) trimethoxysilane (MPTMS) and its application for the determination of lead and cadmium by anodic stripping voltammetry. Xerogels made from bismuth-modified MPTMS and mixtures of it with tetraethoxysilane, under basic conditions (NH₃·H₂O), were characterized with scanning electron microscopy, energy dispersive spectroscopy, infrared spectroscopy and electrochemical methods. Bismuth-modified xerogels were mixed with 1.5% (v/v) Nafion in ethanol and applied on glassy carbon electrodes. During the electrolytic reductive deposition step, the bismuth compound on the electrode surface was reduced to metallic bismuth. The target metal cations were simultaneously reduced to the respective metals and were preconcentrated on the electrode surface by forming an alloy with bismuth. Then, an anodic voltammetric scan was applied in which the metals were oxidized and stripped back into the solution; the voltammogram was recorded and the stripping peak heights were related to the concentration of Cd(II) and Pb(II) ions in the sample. Various key parameters were investigated in detail and optimized. The effect of potential interferences was also examined. Under optimum conditions and for preconcentration period of 4 min, the 3σ limit of detection was 1.3 μg L⁻¹ for Pb(II) and 0.37 μg L⁻¹ for Cd(II), while the reproducibility of the method was 4.2% for lead (n = 5, 10.36 μg L⁻¹ Pb(II)) and 3.9% for cadmium (n = 5, 5.62 μg L⁻¹ Cd(II)). Finally, the sensors were applied to the determination of Cd(II) and Pb(II) ions in water samples.     

A holodirected Pb(II) architecture based on bifunctional tetrazole-carboxylate and photoluminescence

A new 1-D Pb(II) complex {[Pb₂(H₂O)₄(tppbc)₂]?·?(CH₃)₂NCHO} _n (1) based on tetrazole-carboxylate bifunctional ligand has been prepared and characterized (tppbc?=?3-(4-(2-(1H-tetrazol-5-yl)phenyl-4-yl)phenyl)-2-ethoxy-3H-benzimidazole-4-carboxylic acid). Photo-luminescence measurements indicate that although the fluorescence of tppbc is quenched after coordination, the Pb(II) complex shows strong intense phosphorescence emission. Lifetimes at 298?K and low temperatures agree with the large Stokes shift of 1.     

Anodic Stripping Voltammetry Determination of Pb(II) and Cd(II) at a Bismuth/Poly(aniline) Film Electrode

Abstract

A novel voltammetric method—anodic—using a bismuth/poly(aniline) film electrode has been developed for simultaneous measurement of Pb(II) and Cd(II) at low µg L^?1 concentration levels by stripping voltammetry. The results confirmed that the bismuth/poly(aniline) film electrode offered high‐quality stripping performance compared with the bismuth film electrode. Well‐defined sharp stripping peaks were observed for Pb(II) and Cd(II), along with an extremely low baseline. The detection limits of Pb(II) and Cd(II) are 1.03 µg L^?1 and 1.48 µg L^?1, respectively. The bismuth/poly (aniline) electrode has been applied to the determination of Pb(II) in tap water samples with satisfactory results.     

Novel Three-dimensional Sensor for Rapid Detection of Pb(II) and Cd(II) in Edible Mushrooms

A sensing platform was developed based on the molybdenum disulfide-reduced graphene oxide (MoS₂-RGO). The flower-like MoS₂-RGO nanocomposite had a large number of active sites such as oxygen-containing groups and highly reactive sulfur that contributed to the adsorption and preconcentration of heavy metal ions (HMIs). MoS₂-RGO was synthesized by one-step reduction method. Under optimized conditions, the limits of detection (LODs) for Pb(II) and Cd(II) was 0.13 μg/L and 0.59 μg/L with a linear range of 4.1–207.2 μg/L and 2.2–112.4 μg/L, respectively. The modified sensors had been successfully applied to detect Pb(II) and Cd(II) in three kinds of edible mushrooms.     

羧甲基壳聚糖对铅离子的吸附性能研究

本文研究羧甲基壳聚糖对Pb^2 的吸附作用,探讨反应时间,离子强度,溶液的PH值、羧甲基取代度,温度等因素对吸附性能的影响,结果表明羧基是吸附Pb^2 的主要活性基团,羧甲基壳聚糖对Pb^2 的饱和吸附量为3．1083mmol/g,吸附Pb^2 的能力比壳聚糖,水溶性低聚壳聚糖强。     

Highly Efficient and Selective Removal of Pb(II) ions by Sulfur-Containing Calcium Phosphate Nanoparticles

A facile one-step co-precipitation method was demonstrated to fabricate amorphous sulfurcontaining calcium phosphate (SCP) nanoparticles, in which the sulfur group was in-situ introduced into calcium phosphate. The resulting SCP exhibited a noticeable enhanced performance for Pb(II) removal in comparison with hydroxyapatite (HAP), being capable of easily reducing 20 ppm of Pb(II) to below the acceptable standard for drinking water within less than 10 min. Remarkably, the saturated removal capacities of Pb(II) on SCP were as high as 1720.57 mg/g calculated by the Langmuir isotherm model, exceeding largely that of the previously reported absorbents. Significantly, SCP displayed highly selective removal ability toward Pb(II) ions in the presence of the competing metal ions (Ni(II), Co(II), Zn(II), and Cd(II)). Further investigations indicated that such ultra-high removal efficiency and preferable affinity of Pb(II) ions on SCP may be reasonably ascribed to the formation of rodlike hydroxypyromorphite crystals on the surface of SCP via dissolution-precipitation and ion exchange reactions, accompanied by the presence of lead sulfide precipitates. High removal efficiency, fast removal kinetics and excellent selectivity toward Pb(II) made the obtained SCP material an ideal candidate for Pb(II) ions decontamination in practical application.     

Enhanced Removal of Cu(II) and Pb(II) from Aqueous Solutions by Pretreated Biomass of Fusarium Solani

This study investigated the feasibility of Fusarium solani biomass as a biosorbent for Cu(II) and Pb(II) removal from aqueous solutions. Batch sorption experiments were carried out for Cu(II) and Pb(II) to quantify the sorption kinetics, pH, biosorbent dose and pretreatment of F. solani biomass. Biomass metal uptake clearly competed with protons present in the aqueous medium, making pH an important variable in the process. The maximum biosorption by F. solani biomass was obtained with solutions having pH 5 for both metal ions. An enhanced Cu(II) removal (96.53%) was observed for aluminum hydroxide pretreated biomass. Maximum Pb(II) removal (95.48%) was observed with native biomass. Time dependence experiments for the metal ions uptake showed that adsorption equilibrium reached almost 240 min after metal addition. The kinetic studies showed that the biosorption process followed the pseudo second‐order rate model for Cu(II) and Pb(II). The equilibrium data fitted well to the Langmiur isotherm model.     

孔结构对活性炭吸附水溶液中铅离子的影响

选取三种表面化学性质相近的活性炭(AC),通过等温吸附实验考察活性炭对水溶液中铅离子的吸附性能,利用扫描电子显微镜(SEM)观察活性炭的表面微观形貌,通过低温(77 K)液氮吸附测定活性炭的比表面积和孔容,并分别以密度泛函理论(DFT)和Barrett-Joyner-Halenda (BJH)法计算微孔和中孔的孔径分布.结果表明:选用的三种活性炭AC1、AC2、AC3在比表面积和总孔容上呈依次下降的趋势,但表面开放孔均匀分布的AC2,具有最高的饱和吸附量,孔结构类似颗粒堆积孔的AC3,具有与表面开放孔分布集中的AC1相近的饱和吸附量;通过对孔结构与吸附量的关联分析可知,在活性炭吸附铅离子的过程中, 0.4-0.6 nm的孔是有效吸附孔, 10.5-20.6 nm、20.6-55.6 nm、5.2-10.5 nm三个区间的孔则会对吸附产生阻碍作用.     

Adsorption of Cd(II) by Sol-Gel Silica Doped with N-(dipropylcarbamothioyl)thiophene-2-carboxamide

Sol-gel silica was doped with N,N-(dipropylcarbamothioyl) thiophene-2-carboxamide to investigate the sorption of cadmium (Cd) ions from aqueous media. In doped sol-gel silica, the large reagent molecules entrap into pores, whereas, small metal ions diffuse into pores where they make complex with doped reagent. This complexation can be accomplished by either ion exchange or chelation. Doped sol-gel sorbent was applied for removal of Cd(II) from aqueous solution in our study. Adsorption kinetics, adsorption isotherm, equilibration time, effect of initial concentration of adsorbate, and pH effect on the metal removal were studied to optimize the conditions. The prepared adsorbent shows rapid equilibrium and high stability toward high temperature and applied medium. In addition, desorption of metal ions was carried out by 1 M HCl and, thereafter, sol-gel silica adsorbent was regenerated and reused periodically.     

壳聚糖微球负载的己二胺型聚酰胺-胺树状大分子的制备及对胆红素的吸附

通过反相悬浮反应制备了戊二醛交联的壳聚糖微球。以所制备的壳聚糖微球为载体,合成了己二胺型低代数聚酰胺-胺（Polyamidoamine,简称PAMAM）树枝状大分子（Genaration≤3）。考察了该微球在生理条件下对水溶液中胆红素的吸附行为,以及溶液的pH值,离子强度,温度,胆红素初始浓度,牛血清白蛋白等因素对吸附的影响。结果表明,吸附剂对胆红素具有良好的吸附性能,CS-G2.0,CS-G3.0,CS-G1.0,CS-G0和CS微球的平衡吸附率分别为94.61%,93.44%,92.97%,86.47%,52.38%,CS-G1.0-G3.0微球在0.5h吸附率已经超过70%,1h基本接近平衡,对胆红素的吸附量高达42.78mg/g。     

Size Effects for the Adsorption of Alkali Metal Atoms on the Si(001) Surface

The adsorptions of a series of alkali metal(AM) atoms, Li, Na, K, Rb and Cs, on a Si(001)-2×2 surface at 0.25 monolayer coverage have been investigated systematically by means of density functional theory calculations. The effects of the size of AM atoms on the Si(001) surface are focused in the present work by examining the most stable adsorption site, diffusion path, band structure, charge transfer, and the change of work function for different adsorbates. Our results suggest that, when the interactions among AM atoms are neglectable, these AM atoms can be divided into three classes. For Li and Na atoms, they show unique site preferences, and correspond to the strongest and weakest AM–Si interactions, respectively. In particular, the band structure calculation indicates that the nature of Li–Si interaction differs significantly from others. For the adsorptions of other AM atoms with larger size(namely, K, Rb and Cs), the similarities in the atomic and electronic structures are observed, implying that the atom size has little influence on the adsorption behavior for these large AM atoms on the Si(001) surface.     

Chitosan as a biosorbent for adsorption of iron (II) from fracking wastewater

In this work, porous chitosan (CS) was investigated as a biosorbent for the removal of iron (II) from the synthetic fracking wastewater. The underlying problem with the production water from fracking industries is that it contains iron (II) up to 55 mg/L, which needs to be eliminated. Porous CS had a specific surface area of 1.05 m²/g with the average pore diameter of 319 A, as determined by using Brunauer‐Emmett‐Teller surface area analysis. The kinetics, isotherms, and thermodynamic analysis confirm that the porous CS can be a potential candidate for iron (II) removal. Both the pseudo‐first‐order model and pseudo‐second‐order model have good fit on iron (II) adsorption with the porous CS. Kinetic studies revealed that the CS‐iron (II) adsorption system was controlled by intraparticle diffusion. The monolayer adsorption capacity of the porous CS from Langmuir model was found to be 51.81 mg/g. The experimental data were fitted against common adsorption isotherms and yielded excellent fits in the following order: Langmuir > Temkin > Freundlich > Dubinin‐Radushkevich isotherms. Thermodynamic studies revealed that the adsorption of iron (II) onto porous CS was feasible and spontaneous. The adsorption process is endothermic, and the entropy is the driving force.