基于变形场不同离散方法的柔性机器人动力学建模与仿真

研究了基于变形场不同离散方法的柔性机器人动力学建模和仿真问题. 针对多杆空间链式柔性机器人系统,采用假设模态法、有限元法、Bezier 插值方法和B 样条插值方法对柔性杆变形场进行描述,构造统一形式,运用Lagrange 方法,结合4×4 齐次变换矩阵,在计入柔性杆横向弯曲变形引起的纵向缩短的情况下,推导得到多杆空间柔性机器人动力学方程,并编制基于4 种变形场不同离散方法的多杆空间链式柔性机器人仿真软件.通过仿真算例对柔性机器人系统的动力学问题进行研究. 仿真结果表明:有限元法的计算效率较低;假设模态法在处理较大变形问题时其精度低于Bezier 插值方法和B 样条插值方法的精度;作为新的变形体离散方法,Bezier 插值方法和B 样条插值方法可以有效地描述柔性杆的变形场,并能运用到多杆空间柔性机器人动力学建模中.      

漂浮基柔性两杆空间机械臂的关节运动鲁棒控制与柔性振动最优控制Robust joint motion control and vibration optimal control for a free-floating two-flexible-link space manipulator

讨论了载体位置、姿态均不受控情况下,具有有界干扰及有界未知参数的漂浮基柔性两杆空间机械臂的具有鲁棒性的关节运动控制与柔性振动最优控制算法设计问题。首先选择合理的联体坐标系,利用拉格朗日方程并结合动量守恒原理得到漂浮基柔性两杆空间机械臂系统的动力学方程。通过合理选择联体坐标系与利用奇异摄动理论,实现了两个柔性杆柔性振动之间、关节运动与两柔性杆柔性振动的解耦,得到了柔性两杆空间机械臂的慢变子系统与柔性臂快变子系统。针对两个子系统设计相应的控制规律,即增广鲁棒慢变子系统控制律与柔性臂快变子系统最优控制律,这两个相应的子系统控制规律综合到一起构成飘浮基柔性两杆空间机械臂总的关节运动与臂柔性振动控制的组合控制律。系统的数值仿真证实了方法的有效性。该控制方案不需要直接测量漂浮基的位置、移动速度和移动加速度。     

Control and Parameter Optimization of Flexible Robots*

A hierarchical control concept for flexible robot manipulators is presented. The equations of motion are derived using the multibody system method, incorporating flexible links equipped with surface bonded actuating and sensing devices. Exploiting the structure of the dynamic model, the control concept allows combination of any joint level control for the gross motion of the manipulator with decentralized linear control of the elastic deformation of each flexible link. Therefore, the approach is capable of solving both the problem of fast and precise point-to-point motion, with acceptable vibration characteristics, and the problem of accurate trajectory tracking of the end-effector. Control parameters are found through parameter optimization. In order to verify the proposed control strategy, a SCARA robot with one flexible link is considered.     

考虑热应变的柔性并联空间机械臂动力学

研究考虑热应变的柔性并联空间机械臂动力学性态。用Jourdain速度变分原理建立各机械臂的动力学变分方程,在此基础上根据各物体之间的运动学约束关系,建立柔性多体系统的微分代数混合动力学方程。数值仿真结果表明,当温度升高时,机械臂的轴向约束力和中心刚体的质心运动速度均出现显著振荡,而适当减小温度变化率,可以有效地控制振幅。     

DYNAMICS MODELING,SIMULATION, AND CONTROL OF ROBOTS WITH FLEXIBLE JOINTS AND FLEXIBLE LINKS$^{\bf 1)}$

本文探究了铰柔性对机器人动力学响应和动力学控制的影响. 首先, 建立由$n$个柔性铰和$n$个柔性杆组成的空间机器人模型, 运用递推拉格朗日动力学方法, 得到柔性机器人系统的刚柔耦合动力学方程. 在动力学建模过程中, 除了考虑杆件的拉伸变形、弯曲变形、扭转变形以及非线性耦合变形对机器人系统动力学行为的影响, 还考虑了铰的柔性对机器人动力学响应和控制的影响. 其中, 柔性铰模型是基于Spong的柔性关节简化模型, 将柔性铰看成线性扭转弹簧, 不仅考虑了铰阻尼的存在, 还考虑了柔性铰的质量效应. 其次, 编写了空间柔性铰柔性杆机器人仿真程序, 研究铰的刚度系数和阻尼系数对系统动力学响应的影响. 研究表明: 随着柔性铰刚度系数的增大, 柔性机器人的动态响应幅值减小, 振动频率变大. 随着柔性铰阻尼系数的增大, 柔性机器人的动态响应幅值减小, 振动幅值的衰减速度变快. 可通过调节柔性铰的刚度和阻尼来减小柔性铰柔性杆机器人的振动, 因此铰阻尼的研究具有重要工程意义. 最后, 研究了铰柔性在机器人系统动力学控制中的影响. 在刚性铰机械臂和柔性铰机械臂完成相同圆周运动时, 通过逆动力学方法求解得到两种情况下的关节驱动力矩. 研究表明: 引入柔性铰会使控制所需的驱动力矩变小, 对机器人控制的影响显著.     

柔性铰柔性杆机器人动力学建模、仿真和控制

本文探究了铰柔性对机器人动力学响应和动力学控制的影响. 首先, 建立由$n$个柔性铰和$n$个柔性杆组成的空间机器人模型, 运用递推拉格朗日动力学方法, 得到柔性机器人系统的刚柔耦合动力学方程. 在动力学建模过程中, 除了考虑杆件的拉伸变形、弯曲变形、扭转变形以及非线性耦合变形对机器人系统动力学行为的影响, 还考虑了铰的柔性对机器人动力学响应和控制的影响. 其中, 柔性铰模型是基于Spong的柔性关节简化模型, 将柔性铰看成线性扭转弹簧, 不仅考虑了铰阻尼的存在, 还考虑了柔性铰的质量效应. 其次, 编写了空间柔性铰柔性杆机器人仿真程序, 研究铰的刚度系数和阻尼系数对系统动力学响应的影响. 研究表明: 随着柔性铰刚度系数的增大, 柔性机器人的动态响应幅值减小, 振动频率变大. 随着柔性铰阻尼系数的增大, 柔性机器人的动态响应幅值减小, 振动幅值的衰减速度变快. 可通过调节柔性铰的刚度和阻尼来减小柔性铰柔性杆机器人的振动, 因此铰阻尼的研究具有重要工程意义. 最后, 研究了铰柔性在机器人系统动力学控制中的影响. 在刚性铰机械臂和柔性铰机械臂完成相同圆周运动时, 通过逆动力学方法求解得到两种情况下的关节驱动力矩. 研究表明: 引入柔性铰会使控制所需的驱动力矩变小, 对机器人控制的影响显著.      

A quasi-velocity-based nonlinear controller for rigid manipulators

The problem of position control in the operational space of a robot manipulator is addressed in the paper. The proposed controller is based on equations of motion expressed in terms of normalized generalized velocity components (NGVC) which result from decomposition of the manipulator inertia matrix. The sufficient conditions for global exponential stability of the system under the controller are given. It is shown that using the controller an further insight into the system dynamics is possible. The proposed control algorithm is tested via simulation on a spatial manipulator with three degrees of freedom.     

刚弹耦合的机器人机构动力学方程及其解

本文给出了一般开链弹性机器人机构动力学方程。该方程是由关节广义坐标和杆件模态坐标联立的非线性微分方程组。对方程的刚性性质作了讨论,根据Rosenbrock的二级二阶半隐式Runge—Kutta公械,导出了一种求解弹性机器人机构动力学方程的算法。对一平面二杆操作手机构作了计算。对该例同时也用Gill方法作了计算,验证了上述算法的精度和效率。     

Motion control of the flexible manipulator via controllable local degrees of freedom

In order to improve motion accuracy of the flexible manipulator, an idea of using its topological characteristics to suppress vibration is suggested. The concept of controllable local degree of freedom is proposed and introduced to the topological structure of the flexible manipulator. It is shown that the arbitrary motion provided by the controllable local degrees of freedom plays an important role in eliminating undesired effects of the flexibility. On this basis, a method for reducing motion error of the flexible manipulator is put forward. By planning the motion of controllable local degrees of freedom, the appropriate control force can be constructed to increase the damping force and eliminate the exciting force of the flexible manipulator, thereby improving the end-effector accuracy. The results, demonstrated by the numerical simulations, are highly promising and suggest that controllable local degrees of freedom can be a useful tool in combating the undesired vibration deformation of the flexible manipulator.     

Non-linear dynamics of a flexible single link Cartesian manipulator

The present work deals with the non-linear vibration of a harmonically excited single link roller-supported flexible Cartesian manipulator with a payload. The governing equation of motion of this system is developed using extended Hamilton's principle, which is reduced to the second-order temporal differential equation of motion, by using generalized Galerkin's method. This equation of motion contains both cubic non-linearities of geometric and inertial type in addition to linear forced and non-linear parametric excitation terms. Method of multiple scales is used to solve this non-linear equation and study the stability and bifurcations of the system. Influence of amplitude of the base excitation and mass ratio on the steady state response of the system is investigated for both simple and subharmonic resonance conditions. Critical bifurcation points are determined from the fixed-point responses and periodic, quasi-periodic responses are also found for different system parameters. The results obtained using the perturbation analysis are compared with the previously published experimental work and are found to be in good agreement. This work will be useful for the designer of a flexible manipulator.     

Dymamics of a rotating flexible manipulator with tip load

The dynamics of a flexible manipulator is investigated in this paper. From the point of view of dynamic blance, the motion equations of a rotating beam with tip load are established by using Hamilton's principle. By taking into account the effects of dynamic stiffening and dynamic softening, the stability of the system is proved by employing Lyapunov's approach. Furthermore, the method of power series is proposed to find the exact solution of the eigenvalue problem. The effects of rotating speed and tip load on the vibration behavior of the flexible manipulator are shown in numerical results. Supported by National Natural Science Foundation. of China     

Dynamic Bifurcation of Multibody Systems

In this paper, the process of loss of stability of multibody systems and structures is analyzed. A novel approach is presented and applied to the statically loaded spatial systems for the analysis of a dynamic response of systems imposed on impact, high velocity compulsive motion, or percussive forces. The analysis is based on the solution of the dynamic equations and eigenvalue problem of systems, and of the resultant motion simulation. The flexible systems are discretized using the finite element method. The dynamic equations are derived with respect to the relative coordinates of the finite elements. Large flexible deflections due to a loss of stability are simulated. The initial forms of the possible deformations are defined by the computed eigenvectors solving the eigenvalue problem for the system stiffness matrix. The critical forces and system deflections are then analyzed. Examples of bifurcation of beam and beam structure imposed on compulsive motion, percussive forces, and impact are presented.     

柔性机械臂刚柔耦合运动的摄动解法

本文在建立了柔性机械臂无量纲形式摄动方程的基础上,提出了求解在慢变驱动力矩作用下有阻尼简单柔性机械臂刚柔耦合运动的摄动解法。数值模拟结果较好的证实了本方法的有效性。     

漂浮基柔性空间机器人的鲁棒控制及振动抑制

讨论了漂浮基柔性空间机器人系统的动力学建模、运动控制算法设计以及关节、臂双重柔性振动的分级主动抑制问题. 利用系统动量、动量矩守恒关系和拉格朗日-假设模态法对系统进行动力学分析,建立系统动力学方程. 基于奇异摄动法,将系统分解为表示系统刚性运动部分的慢变子系统, 表示由柔性臂引起的系统柔性运动部分的快变子系统1和表示由柔性关节引起的系统柔性运动部分的快变子系统2. 针对慢变子系统提出一种鲁棒控制方法来补偿系统参数的不确定性和柔性关节引起的转动误差,实现系统期望运动轨迹的渐近跟踪;针对快变子系统1采用线性二次型最优控制器来抑制由柔性臂引起的系统柔性振动;针对快变子系统2设计了基于机械臂和电机转子的转角速度差值的反馈控制器来抑制由柔性关节引起的系统柔性振动. 因此,系统的总控制律为以上3个子系统控制律的综合. 最后通过仿真实验证明了所提出的混合控制方法的有效性.      

Errata: Analytical Treatment of Some Extended Problems in Structural Optimization

ABSTRACT

The recursive Newton-Euler dynamic formulation is used to derive the equations of motion of a manipulator with harmonic drives. The derivation is general, in that the harmonic drive is viewed as a separate body that forms a kinematically closed chain with two contiguous links, leading to a comprehensive dynamic model. The harmonic drive is modeled as a flexible and rigid gear with a high gear reduction ratio. Under different modeling assumptions, the effects of gear flexibility and dynamic coupling are examined using a seven-degree-of-freedom manipulator.     

Inverse dynamics analysis of a general spherical star-triangle parallel manipulator using principle of virtual work

Inverse dynamics of a general model of a spherical star-triangle (SST) parallel manipulator (Enferadi and Akbarzadeh Tootoonchi, Robotica 27:663–676, 2009) is the subject of this paper. This manipulator is of type 3-RRP, has good accuracy and relatively a large workspace which is free of singularities (Enferadi and Akbarzadeh Tootoonchi, Robotica, Revised paper, 2009). First, inverse kinematics utilizing the angle axis representation is solved. Next, velocity and acceleration analysis as well as link Jacobian matrices are obtained in invariant form. Finally, a systematic approach based on the principle of virtual work and the concept of link Jacobian matrices is presented. This method allows elimination of constraint forces and moments at the passive joints from motion equations. It is shown that the dynamics of the manipulator can be reduced to solving a system of three linear equations with three unknowns. Moreover, a computational algorithm for solving the inverse dynamics is developed. Two examples with different trajectories for the moving spherical platform are presented and motor torques are obtained. Results are verified using a commercial dynamics modeling package.     

Dynamic modeling and extended bifurcation analysis of flexible-link manipulator

Abstract

In this article, the nonlinear dynamic analysis of a flexible-link manipulator is presented. Especially, the possibility of chaos occurrence in the system dynamic model is investigated. Upon the occurrence of chaos, the system dynamical behavior becomes unpredictable which in turn brings about uncertainty and irregularity in the system motion. The importance of this investigation is pronounced in similar systems such as double pendulum and single-link flexible manipulator. What makes this study distinct from previous ones is the increase in the number of links as well as the changing the bifurcation parameters from system mechanical parameters to force and torque inputs. To this aim, the motion equations of the N-link robot, which are derived with the aid of the recursive Gibbs-Appell formulation and the assumed modes method, are used. In the end, the equations of motion are developed for a two-link flexible manipulator, and its nonlinear dynamical behavior is analyzed via numerical integration of discrete equations. The results are presented in the form of bifurcation diagrams (for variation of torque amplitude), time histories, phase-plane portraits, Poincaré sections, and fast Fourier transforms. The outcomes indicate that when there is no offset, the decrease in damping results in chaotic generalized modal coordinates. In addition, as the excitation frequency decreases from 2π to π, a limiting amplitude is created at 0.35 before which the behavior of generalized rigid and modal coordinates is different, while this behavior has more similarity after this point. An experimental setup is also used to check the torques as the system input.     

Validation of flexible beam elements in dynamics programs

A spatial beam element for static and dynamic problems which involve large displacements and rotations is described. This beam element is applied to static linear buckling problems, the simulation of the motion of a slider-crank mechanism with a flexible connecting rod and a planar and spatial spin-up motion of a flexible beam. Results are compared with those from the open literature.     

Systematic modeling of a chain of N-flexible link manipulators connected by revolute–prismatic joints using recursive Gibbs-Appell formulation

The main intent of this paper is to represent a systematic algorithm capable of deriving the equations of motion of N-flexible link manipulators with revolute–prismatic joints. The existence of the prismatic joints together with the revolute ones makes the derivation of governing equations difficult. Also, the variations of the flexible parts of the links, with respect to time cause the associated mode shapes of the links to vary instantaneously. So, to derive the kinematic and dynamic equations of motion for such a complex system, the recursive Gibbs-Appell formulation is applied. For a comprehensive and accurate modeling of the system, the coupling effects due to the simultaneous rotating and reciprocating motions of the flexible arms as well as the dynamic interactions between large movements and small deflections are also included. In this study, the links are modeled based on the Euler–Bernoulli beam theory and the assumed mode method. Also, the effects of gravity as well as the longitudinal, transversal and torsional vibrations have been considered in the formulations. Moreover, a recursive algorithm based on 3 ×  3 rotational matrices has been applied in order to derive the system’s dynamic equations of motion, symbolically and systematically. Finally, a numerical simulation has been performed by means of a developed computer program in order to demonstrate the ability of this algorithm in deriving and solving the equations of motion related to such systems.