Li–N dual-doped ZnO thin films prepared by an ion beam enhanced deposition method

Li–N dual-doped ZnO films [ZnO:(Li,N)] with Li doping concentrations of 3 at.%–5 at.% were grown on a glass substrate using an ion beam enhanced deposition(IBED) method. An optimal p-type ZnO:(Li,N) film with the resistivity of 11.4 Ω·cm was obtained by doping 4 at.% of Li and 5 sccm flow ratio of N2. The ZnO:(Li,N) films exhibited a wurtzite structure and good transmittance in the visible region. The p-type conductive mechanism of ZnO:(Li,N) films are attributed to the Li substitute Zn site(LiZn) acceptor. N doping in ZnO can forms the Lii–NOcomplex, which depresses the compensation of Li occupy interstitial site(Lii) donors for LiZnacceptor and helps to achieve p-type ZnO:(Li,N) films. Room temperature photoluminescence measurements indicate that the UV peak(381 nm) is due to the shallow acceptors LiZnin the p-type ZnO:(Li,N) films. The band gap of the ZnO:(Li,N) films has a red-shift after p-type doping.     

ZnO：Sb薄膜的光致发光及拉曼特性研究

利用射频磁控溅射法（MS．RF）在玻璃基片上制备了不同掺杂浓度的ZnO：Sb薄膜．借助X射线衍射仪（XRD）、透射光谱、光致发光谱（PL）和拉曼散射光谱（Raman）等手段研究了Sb掺杂浓度对ZnO薄膜的微结构、光致发光和拉曼特性的影响．结果表明：所有样品均呈现ZnO六角纤锌矿结构且具有高度C轴择优取向;在Sb掺杂ZnO薄膜的拉曼光谱中观察到位于532cm^-1的振动模式,结合XRD分析认为此峰归因于Sb替代Zn位且与0成键的局域振动模式（LVMSb--O）;光致发光谱测试发现,仅在ZnO：Sb薄膜中观察到位于3．11eV附近的紫光发射峰,结合拉曼光谱分析认为此峰与XbZn-O复合体缺陷相关．     

Nucleation control for ZnO nanorods grown by catalyst-driven molecular beam epitaxy

We report a study of the annealing temperature and time on Ag catalyst size and density for subsequent growth of ZnO nanorods by catalyst-driven molecular beam epitaxy (MBE). Two different substrates (SiO₂ and SiN_X) for the Ag deposition were used and the thickness of the Ag held constant at 25 Å. Annealing between 600 and 800 °C produced Ag cluster sizes in the range 8-30 nm diameter on SiO₂ and 10-65 nm on SiN_X with a cluster density from 100 to 2500 mm⁻² for SiO₂ and 30 to 1900 mm⁻² for SiN_X. ZnO nanorods grown on these clusters show single-crystal, wurtzite-phase nature and strong band-edge photoluminescence at 380 nm. The nanorods can also be grown selectively on lithographically-patterned dielectric stripes with Ag clusters formed on top by e-beam evaporation and annealing.     

Structural and electrical properties of single crystalline and bi-crystalline ZnO thin films grown by molecular beam epitaxy

C-oriented ZnO epitaxial thin films are grown separately on the a-plane and c-plane sapphire substrates by using a molecular-beam epitaxy technique. In contrast to single crystalline ZnO films grown on a-plane sapphire, the films grown on c-plane sapphire are found to be bi-crystalline; some domains have a 30o rotation to reduce the large mismatch between the film and the substrate. The presence of these rotation domains in the bi-crystalline ZnO thin film causes much more carrier scatterings at the boundaries, leading to much lower mobility and smaller mean free path of the mobile carriers than those of the single crystalline one. In addition, the complex impedance spectra are also studied to identify relaxation mechanisms due to the domains and/or domain boundaries in both the single crystalline and bi-crystalline ZnO thin films.     

Raman spectroscopy to probe residual stress in ZnO nanowire

Raman spectroscopic studies are performed to probe the stress along the length of a bent ZnO nanowire. The zone‐centre E₂^high optical phonon shows a systematic red shift as the junction point of the two arms of the nanowire is approached. The mechanism of the red shift is discussed on the basis of the tensile strain. From the red shift of the phonon peak position, the strain at different regions on the nanowire is estimated. Stress in the bent nanowire is also investigated using photoluminescence (PL) spectroscopy. Results of both Raman and PL study confirm that the bent nanowire is under tensile strain. Copyright © 2011 John Wiley & Sons, Ltd.     

离子注入ZnO薄膜的拉曼光谱研究

室温下,用80 keV N⁺和400 keV Xe⁺离子注入ZnO薄膜,注入剂量分别为5.0×10¹⁴—1.0×10¹⁷/cm²和2.0×10¹⁴—5.0×10¹⁵/cm².利用拉曼散射技术对注入前后的ZnO薄膜进行光谱测量和分析,研究了样品的拉曼光谱随离子注入剂量的变化规律.实验结果发现,未进行离子注入的样品在99,435 cm<     

Current transport in ZnO/Si heterostructure grown by laser molecular beam epitaxy

The n-ZnO/p-Si heterojunction was fabricated by depositing high quality single crystalline aluminium-doped n-type ZnO film on p-type Si using the laser molecular beam epitaxy technique. The heterojunction exhibited a good rectifying behavior. The electrical properties of the heterojunction were investigated by means of temperature dependence current density-voltage measurements. The mechanism of the current transport was proposed based on the band structure of the heterojunction. When the applied bias V is lower than 0.15 V, the current follows the Ohmic behavior. When 0.15V 0.6 V), the space charge limited effect becomes the main transport mechanism. The current-voltage characteristic under illumination was also investigated. The photovoltage and the short circuit current density of the heterojunction aproached 270 mV and 2.10 mA/cm 2 , respectively.     

ZnO纳米棒的拉曼和发光光谱研究(英文)

本文对采用湿化学方法合成的ZnO纳米棒样品的拉曼光谱和发光光谱进行了研究。由扫描电镜结果可知,合成的ZnO纳米棒具有很好的尺寸发布均匀性,直径在30 nm左右,长度大于1微米。采用显微拉曼光谱技术,得到了632.8 nm波长激发的拉曼光谱,并和体相样品的拉曼光谱进行了对比分析;由325 nm激光波长激发得到的荧光光谱可知样品具有很好的紫外发光性质。     

分子束外延PbTe单晶薄膜的反常拉曼光谱研究

采用分子束外延(MBE)方法在BaF₂(111)衬底上生长了高质量的PbTe单晶薄膜， 拉曼光谱测量观察到了表面氧化物的振动模、布里渊区中心(q≈0)纵光学(LO)声子振动模以 及声子-等离子激元耦合模振动.随着显微拉曼光谱仪激光光斑聚焦深度的改变，各拉曼散射 峰的峰位、积分强度、半高宽等都表现出不同的变化趋势. 随着激光光斑聚焦位置从样品表 面上方3μm处变化到表面下方3μm处，PbTe外延薄膜的LO声子频率从119cm^-1移 动到124cm^{-1关键词： PbTe外延薄膜 拉曼散射 纵光学声子}     

Growth of InN thin films on ZnO substrate by plasma-assisted molecular beam epitaxy

We have studied the microstructure property of InN epitaxial films grown on ZnO substrate by plasma-assisted molecular beam epitaxy. We found that the In₂O₃ compound was produced on ZnO substrate and many pits were formed on the InN films when InN was directly grown on ZnO substrate with the N/In flux ratio less than 40. We demonstrated that the quality of InN film was significantly improved when the In₂O₃ layer was used as a buffer to prevent the reaction between In and the ZnO substrate.     

Electron transport in high quality undoped ZnO film grown by plasma-assisted molecular beam epitaxy

High quality ZnO films were grown on c-plane sapphire substrate using low temperature ZnO buffer layer by plasma-assisted molecular beam epitaxy. The film deposited at 720 °C showed the lowest value of full-width at half maximum for the symmetric (0002) diffraction peak of about 86 arcsec. The highest electron mobility in the films was about 103-105 cm²/V s. From temperature-dependent Hall effect measurements, the mobility strongly depends on the dislocation density at low temperature region and the polar optical phonon scattering at high temperature, respectively. Moreover, by obtaining the activation energy of the shallow donors, it was supposed that hydrogen was source of n-type conductivity in as-grown ZnO films.     

低温电化学沉积ZnO薄膜及光学性质

利用阴极还原沉积原理,在水浴65℃的Zn(NO3)2水溶液中,以金属锌片为衬底电沉积制备了ZnO薄膜。采用拉曼光谱和低温光致发光谱(LTPL)对ZnO膜的光学性质进行了表征。实验表明,较小电沉积过电位制备的样品没有明显的与富锌缺氧有关的580cm-1附近的拉曼峰,呈现373nm的紫外光致发光峰,说明较小的电沉积过电位有利于高晶体质量的ZnO膜生长。     

Characterization of ZnO thin film synthesized on alumina-rich spinel substrate by magnetron sputtering

Zinc oxide (ZnO) thin film has been epitaxially grown on (1 1 1) Mg_0.4Al_2.4O₄ substrate by RF-magnetron sputtering. In resonant Raman scattering, higher-order longitudinal optical phonon modes were clearly observed, revealing high optical quality of the ZnO film. Optical absorption indicated a visible exciton absorption at room temperature. The near band edge emission showed a red shift due to the shrinkage of the band gap with increasing the temperature.     

石墨烯对ZnO微米棒光学特性的影响

采用化学气相沉积(CVD)方法制备了具有良好结晶质量和(002)择优取向的ZnO微米棒。在此基础上,选取单根ZnO微米棒,将其部分搁置于单层石墨烯表面。光致发光(PL)谱结果表明,石墨烯不仅增强了ZnO微米棒的紫外发光强度,同时也对光场在ZnO微米棒中的分布有很大的限域作用。分析认为这是由于石墨烯的表面等离子效应引起了ZnO微米棒与石墨烯之间的光-物质相互作用导致的。在拉曼(Raman)光谱中,石墨烯对ZnO微米棒的E2(L)声子振动模和E2(H)声子振动模的强度具有明显的减弱效应,这进一步证明二者之间存在光子的传输和电荷的转移,从而导致其晶格振动受到抑制。     

Effects of high-dose Ge ion implantation and post-implantation annealing on ZnO thin films

This paper reports that ion implantation to a dose of 1×10¹⁷ ions/cm² was performed on c-axis-orientated ZnO thin films deposited on (0001) sapphire substrates by the sol-gel technique. After ion implantation, the as-implanted ZnO films were annealed in argon ambient at different temperatures from 600-900℃. The effects of ion implantation and post-implantation annealing on the structural and optical properties of the ZnO films were investigated by x-ray diffraction (XRD), photoluminescence (PL). It was found that the intensities of (002) peak and near band edge (NBE) exitonic ultraviolet emission increased with increasing annealing temperature from 600-900℃. The defect related deep level emission (DLE) firstly increased with increasing annealing temperature from 600- 750℃, and then decreased quickly with increasing annealing temperature. The recovery of the intensities of NBE and DLE occurs at \sim 850℃ and \sim 750℃ respectively. The relative PL intensity ratio of NBE to DLE showed that the quality of ZnO films increased continuously with increasing annealing temperature from 600 - 900℃.     

超声处理对ZnO薄膜光致发光特性的影响

对于结晶状态好的ZnO薄膜，测量了其光致发光(PL)光谱，发射光谱中只发现了峰值波长约389 nm的近紫外光.样品进行超声处理后，发射谱中不仅观察到近紫外峰，又观察到波长约508 nm的绿光峰.绿光峰的强度比近紫外光的强度强得多，且近紫外峰红移.进一步的热处理使绿光峰大大增强.超声处理改变了ZnO薄膜的质量和结晶状态，使晶格中产生氧空位.处理过程中的热效应使得薄膜晶格振动加剧.当晶格振动加剧到一定程度，晶格中的氧脱离格点形成氧空位.510 nm左右的绿色发光峰是ZnO晶体中的氧空位产生的.薄膜的温度越高， 关键词： ZnO薄膜 超声 光致发光     

热处理参数对溶胶-凝胶法制备氧化锌薄膜特性的影响

采用溶胶-凝胶旋涂法在Si(111)衬底上生长了ZnO薄膜，并用荧光光谱、原子力显微镜和XRD对ZnO薄膜样品进行了分析.结果表明，溶胶-凝胶旋涂法制备的ZnO薄膜为纤锌矿结构，其c轴取向程度与热处理温度有很大的关系.当热处理温度小于550℃时，氧化锌薄膜在室温下均有较强的紫外带边发射峰，而可见波段的发射很弱；当热处理温度高于550℃时，可见波段发射明显增强.对经过不同时间热处理的ZnO薄膜样品分析表明，氧化锌薄膜的荧光特性及表面形貌与热处理时间也有很大关系，时间过短可见波段的发射较强，但时间过长会导致晶 关键词： ZnO薄膜 光致发光     

Structural and optical properties of ZnO film by plasma-assisted MOCVD

High quality ZnO film was deposited by plasma-assisted metal-organic chemical vapor deposition (MOCVD). We observed a dominant peak at 34.6° due to (0 0 2) ZnO, which indicated that the growth of ZnO film was strongly C-oriented. The full-width at half-maximum (FWHM) of the -rocking curve was 0.56° indicating relatively small mosaicity. Photoluminescence (PL) measurement was performed at both room temperature and low temperature. Ultraviolet (UV) emission at 3.30 eV was found with high intensity at room temperature while the deep level transition was weakly observed at 2.513 eV. The ratio of the intensity of UV emission to that of deep level emission was as high as 193, which implied high quality of ZnO film. From PL spectrum at 10 K, we observed A-exciton emission at 3.377 eV and D°X bound exciton transition at 3.370 eV. The donor–acceptor transition and LO phonon replicas were observed at 3.333 and 3.241 eV respectively. Raman scattering was performed in back scattering at room temperature. The E₂, A_1(LO) and A_1(TO) mode was seen at 437.6, 575.8 and 380 cm^–1 respectively. In comparison with Raman spectrum of ZnO powder, we found that ZnO film was nearly free of strain, which indicated high crystal quality.     

Nitrogen-doped ZnO prepared by capillaritron reactive ion beam sputtering deposition

Nitrogen-doped ZnO thin films have been prepared by reactive ion beam sputtering deposition utilizing a capillaritron ion source. X-ray diffraction (XRD) analysis of the as-deposited film exhibits a single strong ZnO (002) diffraction peak centred at 34.40°. Post-growth annealing causes increase of grain size and decrease of c-axis lattice constant. Micro-Raman spectroscopy analysis of the as-deposited film shows strong nitrogen-related local vibration mode at 275, 582, 640 and 720 cm⁻¹, whereas the E₂ mode of ZnO at 436 cm⁻¹ can barely be identified. Annealing at 500-800 °C causes decrease of 275, 582, 640 and 720 cm⁻¹ and increase of 436 cm⁻¹ intensity, indicating out-diffusion of nitrogen and improvement of ZnO crystalline quality. Unlike un-doped ZnO, the surface roughness of nitrogen-doped ZnO deteriorates after annealing, which is also attributed to the out-diffusion of nitrogen. A nitrogen concentration of ∼10²¹/cm³ was observed while type conversion from n-type to p-type was not achieved, which is likely due to the formation of Zn_I-N_O or (N₂)_O that act as donor/double donors.