Effects of Cs and Na ions on the interfacial properties of dodecyl sulfate solutions

The competitive binding of counterions to anionic dodecyl sulfate ions in aqueous solutions of cesium dodecyl sulfate (CsDS) and sodium dodecyl sulfate (SDS) mixtures, which significantly influences the critical micelle concentration (cmc) and surface (or interfacial) tension of surfactant solutions, was investigated. The cmc and degree of counterion binding were obtained through electrical conductivity measurements. The curve of cmc versus the mole fraction of CsDS in the surfactant mixture was simulated by Rubingh's equations, which enabled us to estimate the interaction parameter in micelles (W _R) based on the regular solution approximation. The curve-fitting exhibited a slightly negative value (W _R=−0.1), indicating that the mixing (SDS+CsDS) enhances micelle formation owing to a greater interaction between surfactant molecules and counterions than in pure systems (SDS). On going from SDS, SDS:CsDS(75:25), SDS:CsDS(50:50), SDS:CsDS(25:75) to CsDS, interfacial tension at the hexadecane/surfactant-solution interface showed a negative deviation from the mixing rule (interaction parameter in adsorbed film W _A=−0.38), indicating the replacement of Na⁺ bound to anionic dodecyl sulfate by Cs⁺ ions owing to the stronger interaction between the Cs⁺ and the dodecyl sulfate ions. Droplet sizes of emulsion formed with hexadecane and aqueous dodecyl sulfate solutions were investigated using the light scattering spectrophotometer. The higher binding capacity of Cs⁺, having a smaller hydrated ionic size than Na⁺, also resulted in a negative deviation in emulsion droplet size in mixed systems. Received: 10 May 2000/Accepted: 11 August 2000     

Effect of pH on the Flocculation of SDS Micelles by Al3+

SDS micelles flocculate in the presence of Al³⁺, creating an aggregate with pollutant-removing properties. The fraction of SDS micelles flocculating depends on the concentrations of SDS and Al³⁺. This paper describes how this fraction also changes with pH. There are two reasons for this dependence: a change in pH has a strong effect in the solution chemistry of Al³⁺, converting it into the compound [Al₁₃O₄(OH)₂₄]⁷⁺, a strong flocculant, or precipitating it as Al(OH)₃; and at low pH protons may compete with Al³⁺ as binding counter-ions for micelles. An increase in pH allows flocculation of SDS at high concentrations of Al³⁺, which under unmodified pH does not occur. Micelle flocculates are reported in this work to exist between pH 5 and pH 8, suggesting the potential use of Adsorptive Micellar Flocculation for the removal of anionic pollutants from waste waters not necessarily limited to acidic solutions. Received: 18 August 2000 Accepted: 5 October 2000     

Complexation of Cu(II) with Glycine in Aqueous Solution of an Anionic Surfactant

The complexation of Cu²⁺ with glycine in aqueous solution of an anionic surfactant, sodium dodecyl sulfate, was studied spectrophotometrically. Sodium dodecyl sulfate in concentrations above the critical micellization concentration participates in the complexation. The composition of the complexes and the equilibrium constants of the complexation were determined.__________Translated from Zhurnal Obshchei Khimii, Vol. 75, No. 3, 2005, pp. 383–385.Original Russian Text Copyright © 2005 by Vladimirova, Morgunova, Ramenskaya.     

Rheology of viscoelastic anionic micellar solutions in the presence of a multivalent counterions

The growth and structure of anionic micelles sodium dodecyl trioxyethylene sulfate (SDES) in the presence of a multivalent counter-ion, Al³⁺, were investigated by means of rheological methods and the technique of freeze-fracture transmission electron microscopy. It was found that wormlike micelles and network structures could be formed in SDES/AlCl₃ aqueous micellar solutions, according to the measurements of the zero-shear viscosity, the complex viscosity and the dynamic moduli (storage modulus and loss modulus), and the application of the Cox–Merz rule and a Cole–Cole plot. The cyclic shear test, the plateau modulus and the relaxation time were also studied to express the rheological properties of the wormlike micellar solutions. The structure was of a character of a nonlinear viscoelastic fluid and departed from the simple Maxwell model. Received: 23 November/2000 Accepted: 31 January 2001     

The influence of surfactants on latex flocculation with poly(diallyldimethyl ammonium chloride)

Aqueous latex was flocculated by mixtures of poly(diallyldimethyl ammonium chloride), PDADMAC, and anionic surfactants. Sodium dodecyl sulfate, (SDS), and Aerosol OT influenced flocculation whereas nonionic Tergitol NP-10 did not. The flocculation domains were correlated with properties of the polymer-surfactant complexFlocculation was never observed above the CMC of the corresponding surfactant solution without polymer or latex. At SDS concentrations greater than 10^–3.6 M the flocculation boundary corresponded to the first appearance of insoluble polymer-surfactant complex which was characterized by dynamic light scattering and microelectrophoresis. Under these conditions latex (diameter 570 nm) and dispersed polymer-surfactant complex particles (diameters between 30 and 2 000 nm) displayed simultaneous homo and heteroflocculation. The boundaries of the flocculation domains at low surfactant concentration were determined by the ratio of polymer to latex and by the net electrostatic charge of the soluble polymer-surfactant complex. On the other hand, the mechanisms controlling flocculation boundaries in the dispersed polymer-surfactant domain require further clarification.     

Rheology and microstructure studies of SDS/CTAB/H2O system

Phase behavior of mixed sodium dodecyl sulfate (SDS) and cetyl trimethyl ammonium bromide (CTAB) aqueous solution was studied. The rheological properties and microstructure were investigated using a rheostat and freeze-fracture technique and are shown to be closely related to the phase behavior. Experimental investigations reveal two symmetrical aqueous two-phase systems (ATPS) in the ternary phase diagram of SDS/CTAB/H₂O system. In the surfactant rich phase of ATPS or in the adjacent stoichiometric state of ATPS, the system has high viscosity because of its long range ordered structure. Lamellar phase was found in the high viscosity samples in which the cationic and anionic surfactant are in 1: 3 or 3: 1 stoichiometry. In addition, the viscosity has a tendency to increase when salt was added to the solution. The viscosity increase is due to the salt can screen the repulsion between different charged headgroups and thus reduces the effective size of surfactants and facilitates the spherical or rod likes micelles to be transformed to worm-like micelles which can form hexagonal or liquid crystal phases. Large-size salt ions like sodium sulfate (especially organic salt ions) have more significant effect on the surfactant solution viscosity. The text was submitted by the authors in English.     

Effect of Micelle Composition on Acidic Drugs Separation Behavior by Micellar Electrokinetic Capillary Chromatography

Micellar electrokinetic capillary chromatography (MECC) is a branch of capillary electrophoretic techniques, in which surfactant micelles are added to the electrolyte solution as pseudostationary phase. Separation in MECC is based on electrophoretic mobilities of the analytes when partitioned into micelles1. In this work, four acidic drugs similar in structure with aryl carboxylic acid were separated by MECC. The effects of type of surfactant, such as anionic surfactant SDS, nonionic …     

Salt Effects on the Aqueous Two-Phase System of Gemini(12-3-12, 2Br<Superscript>−</Superscript>)/SDS/PEG

The effect of added salts (NaCl, KCl and NaBr) on the aqueous two-phase system (ATPS) formed in mixtures of Gemini(12-3-12, 2Br⁻)/sodium dodecyl sulfate/polyethylene glycol has been investigated. Phase diagrams of the aqueous systems containing Gemini(12-3-12, 2Br⁻), sodium dodecyl sulfate (SDS), polyethylene glycol(PEG) and a salt have been determined experimentally at 313.15 K. The results indicate that the addition of salts not only induces the appearance of ATPS-A (in which anionic surfactant is in excess), shortens the phase separation time, enlarges the regions of ATPS-C (in which cationic surfactant is in excess), and decreases the minimum concentration required for forming an ATPS, but also alters the matching between anionic and cationic surfactants. Extractive experiments also showed that these salts notably enhance the extraction ability of ATPS; the Gemini-rich phase exhibits prominent cohesive action with xylenol orange, regardless of whether or not it is the upper phase or the lower phase.     

Interaction of slightly cross-linked gels of poly(diallyldimethylammonium bromide) with sodium dodecyl sulfate. Diffusion of surfactant ions in gel

The dynamics of the changing microenvironment of the fluorescent probe pyrene in slightly cross-linked networks of poly(diallyldimethylmmonium bromide) during diffusion of sodium dodecyl sulfate (SDS) in the gel phase has been investigated by fluorescence spectroscopy. Values of the spectral ratio I₃/I₁ for pyrene monomer included in SDS micelles in the swollen networks fall between the corresponding values for pyrene in water and for pyrene dissolved in SDS micelles in aqueous solution. In the narrow interval of the surfactant concentrations in the gel phase, the formation of pyrene excimers is observed. The values of the critical micelle concentration in the gel phase (ca. 5 × 10^?4 to 8 × 10^?4 mol/L) are tenfold lower than in aqueous solutions of the surfactant. The effective micellar diffusion coeffecient D in the gel phase increases with increasing swelling of the network. © 1993 John Wiley & Sons, Inc.     

BEHAVIOR OF ANIONIC SURFACTANT MICELLES IN THE PRESENCE OF Al3+ AND Ca2+

The estimation of the C-potential of ionic surfactant micelles may be useful for the study of adsorption of solutes onto the micellar surface, which causes a reduction of the net electrostatic charge. This work presents results on the variation of ζ-potential of alkylsulfate and fatty carboxylate micelles with the bulk concentrations of Al³⁺ and Ca²⁺ cations. Combined with results from the literature about the effect of micellar surfactant concentration on reducing surfactant precipitation in the presence of polyvalent cations, these allow to conclude that micelles of anionic surfactants will have a higher chance of electroneutralization of their surface charge by adsorbing cations if the end functional group of the surfactant is smaller.     

Micellar-enhanced ultrafiltration of cadmium ions with anionic–nonionic surfactants

Micellar-enhanced ultrafiltration (MEUF), a surfactant-based separation process, is promising in removing multivalent metal ions from aqueous solutions. The micellar-enhanced ultrafiltration of cadmium from aqueous solution was studied in systems of anionic surfactant and mixed anionic/nonionic surfactants. The micelle sizes and zeta potentials were investigated by dynamic light scattering measurements. The effects of feed surfactant concentration, cadmium concentration and the molar ratio of nonionic surfactants to sodium dodecyl sulfate (SDS) on the cadmium removal efficiency, the rejection of SDS and nonionic surfactants and the permeate flux were investigated. The rejection efficiencies of cadmium in the MEUF operation were enhanced with higher SDS concentration and moderate Cd concentration. When SDS concentration was fixed at 3 mM, the optimal ranges of the molar ratios of nonionic surfactants to SDS for the removal of cadmium were 0.4–0.7 for Brij 35 and 0.5–0.7 for Triton X-100, respectively. With the addition of nonionic surfactants, the SDS dosage and the SDS concentration in the permeate were reduced efficiently.     

Properties and Extraction for [Ni(NH3)6]2+ of ATPS-a Formed by Aqueous Cationic–Anionic Surfactant Mixtures

The properties and extraction for [Ni(NH₃)₆]²⁺ of anionic aqueous two-phase systems (ATPS-a) that formed in mixtures of cetyltrimethylammonium bromide (CTAB) and excess sodium dodecyl sulfate (SDS) aqueous solutions were investigated. The results showed that the properties and extraction effects were strongly affected by the surfactant concentration, the temperature of system, and the mole fraction of surfactants. The increase of temperature induces narrower phase region and larger phase volume ratio. In addition, [Ni(NH₃)₆]²⁺ was extracted into the surfactant-rich phase with higher distribution coefficient when the liquid crystal had the birefringent properties. Moreover, the distribution coefficient can be improved through reducing the concentration of surfactant from 0.15 to 0.05 mol · L^?1 or increasing mole fraction of CTAB from 21.9% to 23.1%. The results showed that ATPS of cationic–anionic surfactants was efficient for [Ni(NH₃)₆]²⁺ extraction with distribution coefficients of 13.5 when the total surfactant concentration was 0.05 mol · L^?1, mole fraction of CTAB was 21%, and temperature was 34°C.     

Photolysis of 1,2-dihydroquinolines in micellar solutions of anionic and cationic surfactants

The kinetics of the photolysis of substituted 1,2-dihydroquinolines (DHQ) in micellar solutions was studied by steady-state and flash photolysis. The photolysis mechanism depends dramatically on the location of DHQ molecules in micelles, which is governed by the surfactant nature. In micellar solutions of the anionic surfactant sodium dodecyl sulfate (SDS), where the DHQ molecules are located in the Stern layer, the intermediate species decay kinetics follows a first-order law. When DHQ is in neutral form (pH 4–12), the rate constant of the intermediate carbocation decay increases from 25 to 198 s^?1 with an increasing concentration of DHQ in micelles. The positive micellar catalysis is caused by the acceleration of the final product formation with the DHQ molecule via proton abstraction from the intermediate cation. The formation of several types of intermediate species—carbocations in the aqueous phase and aminyl radicals in micelles—is observed in micellar solutions of the cationic surfactant cetyltrimethylammonium bromide (CTAB) due to the preferential location of DHQ molecules in the micellar core. The carbocation decays via a pseudofirst-order reaction with a rate constant close to that in the aqueous solution. The lifetime of the DHQ aminyl radicals in the micellar solutions is longer by several orders of magnitude than the lifetime observed for homogeneous solutions of hydrocarbons and alcohols.     

Physicochemical Properties of Aqueous Solutions of Binary Mixtures of Lignin Derivatives and Sodium Dodecyl Sulfate

Physicochemical properties of aqueous solutions of binary mixtures of lignosulfonates and sodium dodecyl sulfate were studied. Introduction of sodium dodecyl sulfate into solutions of high-molecular-mass lignosulfonates at certain ratios causes macrophase separation of the systems with the formation of loose precipitates. A synergistic effect of a decrease in the surface tension is observed in the mixed solutions. This effect increases with increasing lignosulfonate molecular mass and temperature. The revealed relationships are caused by hydrophobic interactions of hydrocarbon radicals of sodium dodecyl sulfate with hydrophobic segments of lignosulfonate polymer chains with the formation of micellar associates. Aqueous solutions of binary mixtures of lignosulfonates (с_LS ≥ 0.2 g dm^–3) and sodium dodecyl sulfate (с_DSNa ≥ 0.08 g dm^–3) can be recommended for use as surfactant formulations for high-temperature autoclave leaching of polymetal ores.     

Shape and Structure Formation of Mixed Nonionic–Anionic Surfactant Micelles

Aqueous solutions of a nonionic surfactant (either Tween20 or BrijL23) and an anionic surfactant (sodium dodecyl sulfate, SDS) are investigated, using small-angle neutron scattering (SANS). SANS spectra are analysed by using a core-shell model to describe the form factor of self-assembled surfactant micelles; the intermicellar interactions are modelled by using a hard-sphere Percus–Yevick (HS-PY) or a rescaled mean spherical approximation (RMSA) structure factor. Choosing these specific nonionic surfactants allows for comparison of the effect of branched (Tween20) and linear (BrijL23) surfactant headgroups, both constituted of poly-ethylene oxide (PEO) groups. The nonionic–anionic surfactant mixtures are studied at various concentrations up to highly concentrated samples (ϕ ≲ 0.45) and various mixing ratios, from pure nonionic to pure anionic surfactant solutions. The scattering data reveal the formation of mixed micelles already at concentrations below the critical micelle concentration of SDS. At higher volume fractions, excluded volume effects dominate the intermicellar structuring, even for charged micelles. In consequence, at high volume fractions, the intermicellar structuring is the same for charged and uncharged micelles. At all mixing ratios, almost spherical mixed micelles form. This offers the opportunity to create a system of colloidal particles with a variable surface charge. This excludes only roughly equimolar mixing ratios (X≈ 0.4–0.6) at which the micelles significantly increase in size and ellipticity due to specific sulfate–EO interactions.     

The pH dependence of dispersion of TiO2 particles in aqueous surfactant solutions

The pH dependence of dispersion of titanium dioxide (TiO₂) particles has been examined in the presence of surfactant molecules in water. Whereas particles were dispersed in water at acid and alkaline regions rather than at neutral region, the dispersion was enhanced at neutral region in an aqueous sodium dodecyl sulfate (SDS) solution and at acid and alkaline regions in an aqueous dodecyldimethylamine oxide (C₁₂DAO) solution. Considering the pH dependence of zeta potential, the adsorption models of surfactant molecules on a particle were estimated on the basis of the modes of hemimicelle and double-layer compression. While the particles that adsorbed Al³⁺ were remarkably dispersed around pH 6, their dispersion does not largely depend on pH in the addition of SDS, indicating the adsorption of SDS molecules to form double-layer compression in the whole pH region. Dynamic light-scattering measurement and electron microscopic observation suggested that the particles were dispersed in water as small flocs.     

Encapsulation of curcumin in cationic micelles suppresses alkaline hydrolysis

The alkaline hydrolysis of curcumin was studied in three types of micelles composed of the cationic surfactants cetyl trimethylammonium bromide (CTAB) and dodecyl trimethylammonium bromide (DTAB) and the anionic surfactant sodium dodecyl sulfate (SDS). At pH 13, curcumin undergoes rapid degradation by alkaline hydrolysis in the SDS micellar solution. In contrast, alkaline hydrolysis of curcumin is greatly suppressed in the presence of either CTAB or DTAB micelles, with a yield of suppression close to 90%. The results from fluorescence spectroscopic studies reveal that while curcumin remains encapsulated in CTAB and DTAB micelles at pH 13, curcumin is dissociated from the SDS micelles to the aqueous phase at this pH. The absence of encapsulation and stabilization in the SDS micellar solution results in rapid hydrolysis of curcumin.     

Rheological Properties of Anionic Surfactant Solutions in the Presence of Al3+ Counterion

Aqueous solutions of ionic surfactants with strongly binding counterions exhibit wormlike or network properties. The properties of anionic micelles of sodium dodecyltrioxyethylene sulfate (AES) in the presence of multivalent counterion Al³⁺ were investigated by dynamic rheological methods. The steady-shear viscosity and stress, the zero-shear viscosity, the complex viscosity, and the dynamic shear modulus have been determined as a function of the surfactant and salt concentrations. Some interesting and noticeable results have been obtained, which can express the micellar growth and structure. The formation of wormlike micelles or network structure in surfactant solutions becomes much easier with increasing surfactant and salt concentrations. The Cox-Merz rule and the Cole-Cole plot are not applicable perfectly to the systems studied. The nonlinear viscoelasticity and non-Newtonian behavior can be found in all solutions according to the comparison with the simple Maxwell model. The technique of freeze-fracture transmission electron microscopy (FF-TEM) was also applied to confirm the formation of these interesting structures.     

Morphological control of calcium carbonate crystallized in reverse micelle system with anionic surfactants SDS and AOT

The influence of a surfactant over water on the polymorphism and crystal size of calcium carbonate produced by reaction crystallization in microemulsion systems was investigated in a mixing tank reactor. The crystallization was induced by the reaction between two aqueous micelle solutions (Na2CO3-CaCl2) stabilized by anionic surfactants, SDS (sodium dodecyl sulfate) or AOT (sodium bis(2-ethylhexyl) sulfosuccinate). With increasing surfactant ratio to water, the water-in-oil microemulsion was stably developed and the morphology of the calcium carbonate crystallized in the micelles sharply transformed from calcite to vaterite. The influence of SDS on the polymorphism and crystal size of calcium carbonate was much clearer than that of AOT. In addition, with AOT, certain step changes in the morphology and crystal size occurred around a surfactant ratio to water (R=[H2O]/[surfactant]) of 15 due to a two-phase separation of the microemulsion.     

Threadlike micelle formation of anionic surfactants in aqueous solution

We have investigated the formation of threadlike micelles consisting of anionic surfactants and certain additives in aqueous solution. Threadlike micelles long enough to be entangled with each other were formed in a clear aqueous solution of two anionic surfactants, sodium hexadecyl sulfate and sodium tetradecyl sulfate. These solutions also contained pentylammonium bromides or p-toluidine halides and exhibited remarkable viscoelasticity. Because the molar ratio of surfactants to cationic additives in these micelles seemed close to unity, they formed 1:1 stoichiometric complexes between surfactant anions and additive cations, as previously found in systems of cationic surfactants such as hexadecyltrimethylammonium bromide and sodium salicylate. The viscoelastic behavior of these anionic threadlike micellar systems was adequately described by a simple Maxwell element with a single relaxation time and strength, as in many similar cationic systems.