The electrophoretic deposition of polyvinyl chloride organosol from organic medium

The results of the studies on the influence of PVC organodispersions properties on the gram-equivalent (Q) of organosol electrophoretically deposited on the electrode have been presented in this work. The influence of the electrical conductivity and organosol concentration on electrophoresis have been determined. The mechanism of organosol particle-potential formation with respect to swelling processes and dispersive agent adsorption have been pointed out.     

Formation of ultra-thin films consisting of proteins or polysaccharides and syndiotactic-rich poly-vinyl alcohol mixtures adsorbed at air-solution interface

Ultra-thin films of syndiotactic-rich poly-vinyl alcohol (s-PVA) with several proteins and polysaccharides were prepared by the bubble and frame methods using a mixed dilute aqueous solution (1.5g/dL).The mixed amount of-cyclodextrin (-CD) was the largest among these proteins and polysaccharides giving a weight ratio (-CD/s-PVA) of 1. The ratios of silk fibroin(SF), lysozyme, pepsin, and pectin tos- PVA were 0.58, 0.40, 0.35, and 0.35, respectively. For the-CD/s-PVA and SF/s-PVA blend thin films, the phase separation was observed.     

Spontaneous film formation from a polymer solution

An unusual continuous film formation process of lateral pentyloxy substituted poly(p-phenylene terephthalate)s (s-PPPT) and poly(carbonate) (PC) is observed. A liquid film of polymer solution creeps over the surface of water dropped into the polymer solution. By vaporization of the solvent a solid polymer film is formed on the water surface and can be removed. The driving force for the film formation mechanism is assumed by the reduction of the surface tension of water. Experiments verify this mechanism by increasing the film formation speed using a gas stream, by reducing the formation speed through lowering the surface tension by rinsing agents, and by lowering the solubility of the polymer. As expected, no effects are found by variation of the pH-value of water. Necessary conditions for the film formation process are: good solubility of the polar polymers in organic solvents having a high vapor pressure, complete phase separation, solution density higher than water density, and a surrounding gas phase unsaturated with solvent vapor.The thickness of the mechanically stable films is less than 0.5 m. The films are amorphous by microscopical, FT-IR, x-ray, and DTA investigations.     

Azeotropic transformation in mixed monolayers of octadecylurea and hexadecylurea

The surface pressure of mixed monolayers of octadecylurea and hexadecylurea has been measured as a function of mean area per molecule at various temperatures and compositions. The surface pressure of the phase transition obtained was observed to decrease both with an increase in temperature and with an addition of another component. With the aid of the thermodynamic method developed previously, the apparent molar entropy and energy changes associated with the phase transition were found to be positive. These positive values were explained by the rupture of the intermolecular hydrogen bonding. Furthermore, the activity coefficients of film-forming components with reference to their respective pure components were considered in connection with the mutual interaction between octadecylurea and hexadecylurea molecules. It was concluded that the system exhibits the negative azeotropy as a result of the difficulty in forming the hydrogen bonding in the mixed monolayer.     

Aqueous dispersion of polyurethane ionomers from hexamethylene diisocyanate and trimellitic anhydride

Polyurethane (PU) ionomers were prepared from trimellitic anhydride (TMA), poly(tetramethylene adipate) glycol (PTAd), and hexamethylene diisocyanate (HDI) in acetone. Upon neutralizing the carboxylic groups with a tertiary amine (TEA), and adding water to PU ionomer solution, followed by removing the acetone, stable aqueous PU dispersions were obtained.Effects of interionic molecular weight and nonionic hydrophilic segment, viz. monofunctional ethylene-propylene oxide ether on particle, size, emulsion viscosity, mechanical, and viscoelastic properties of the emulsion cast films were examined.     

Thermodynamics of surfactant-dye complex formation in aqueous solutions. Sodium alkyl sulfates and azo oil dye systems

Thermodynamics of surfactant-dye complex formation have been studied, in terms of equilibrium coefficient, using a spectrophotometer. The systems are 6 sodium alkyl sulfates, which have different alkyl chain lengths, and 4-phenylazo-1-naphthylamine. A pronounced spectral change in the dye solution occurs on addition of the surfactant; the change has a definite isosbestic point and a new absorption band at 535 nm because of surfactant-dye complex formation, which is caused by hydrophilic-hydrophilic interaction. As the alkyl chain length in the surfactant increases, the values of free energy change (negative) increase, while the value of enthalpy change (negative) increases and the value of entropy change (positive) decreases. The longer the alkyl chain length in surfactant increase, the more stable the surfactant-dye complex becomes.Surfactant-dye complex will form due to hydrophilic-hydrophilic interaction and will become more stable due to hydrophobic-hydrophobic interaction.     

Differential scanning calorimetric study of phase changes in poly(ethylene glycol) dodecyl ether-water systems

Phase changes in binary systems of poly(ethylene glycol) dodecyl ethers, C₁₂H₂₅(OC₂H₄)_xOH (x=5, 6 and 8) with water have been studied between –40 to 100 C by differential scanning calorimetry. A number of transitions, including the liquidliquid phase separation, were seen and the transition temperatures and enthalpy changes were determined. The observed temperatures were generally in good agreement with reported phase diagrams. In the C₁₂E₅ system, three of the four three-phase lines were seen and a more complete phase diagram is suggested for the water-rich part of the system. Most of the phase changes seen above 0 C are accompanied by small endothermic enthalpy changes of 0.7 to 0.9 kJ (mol C₁₂E_x)^–1, independent of system studied, type of transition and transition temperature. Water-rich solutions and liquid crystalline phases separate upon freezing into ice and crystals of hydrated amphiphile. Eutectics are developed at the following temperatures and compositions: C₁₂E₅ –3.0 C and 54 wt % C₁₂E₅; Q₂E₆ –4.5 C and 54 wt % C₁₂E₆, C₁₂E₈ –3.8 C and 49 wt % C₁₂E₈.     

Thermodynamic consideration on the interface formation of water and ethylene glycol isobutyl ether mixture

The interfacial tension of the binary two-phase mixture of water and ethylene glycol isobutyl ether (EIB) was measured as a function of temperature in the vicinity of the lower critical solution temperatureT _c under atmospheric pressure. The interfacial tension decreased with decreasing temperature and approached zero atT _c . The thermodynamic quantities of interface formation were evaluated by applying equations developed previously to the interfacial tension vs temperature curves. The results were compared with those of the water and diethylene glycol diethyl ether system examined previously, and the effect of the molecular structure of the ether molecule on its interfacial behavior was discussed. It was suggested that the hydration of the ethylene oxide groups of ether molecules was an important factor in the interface formation as well as in the mixing of component molecules of the systems investigated here.     

Donator acceptor behavior of aerosil in several organic liquids

Aerosil is studied with regards to its acceptor behavior by means of electrokinetic measurements and UV measurements in various organic liquids. Whereas the values of the general negativ zeta-potential only approximately correspond with the donor number of the liquids determined according to Gutmann, Marie and Gal, and Kravtzov et al., an excellent agreement between zeta-potential and the UV maximum of a dicyano-bis(1,10-phenanthrolin)-ferric [Fe(phen)₂(CN)₂] complex adsorbed at the solid-liquid interface was found. The fact that traces of water decrease the negative zeta-potential of aearosil in organic liquids is attributed to hydration of the aerosil surface.Dedicated to Professor Dr. Josef Schurz on the occasion of his 65th birthday.     

Micelle aggregation numbers from colligative properties

An equilibrium model has been developed to derive micelle aggregation numbers n from colligative properties of surfactant solutions, with special regard to freezing point depression. The introduction of a mass action approach in the solute activity equation allows to get aggregation numbers close to those obtained from light scattering. The model can be applied with small formal changes to ionic and nonionic surfactants.     

The adsorption process of some acetic acid derivatives at the water/air interface

The adsorption of trifluoro-, trichloro-, tribromo-, and trimethylacetic acid at the water/air interface is discussed on the basis of surface tension measurements. The process of adsorption is described by Henry's and Langmuir's isotherm equations. The obtained results allow calculation of the standard free energy of adsorption of investigated molecules and the contribution to this energy of hydrophobic groups of these molecules.     

Thermodynamics of adsorption of acetone on active carbon supported metal adsorbents

Adsorption of acetone on active carbon and active carbon supported metals (Ni, Cu, Zn and Cd) have been studied as a function of temperature. Thermodynamic parameters such as G ⁰, H ⁰, and S ⁰ are calculated from virial and Langmuir isotherm expressions. It is observed that active carbon supported metals have more adsorption affinity for acetone as compared to active carbon. Results show that the increase in adsorption affinity for active carbon supported metals is not due to configurational factors affecting the entropy of adsorption, but because of enhanced enthalpy of adsorption. XRD spectra show that active carbon supported metals adsorbents are amorphous and metal residues are present on the surface of active carbon in its reduced form. From adsorption data, isosteric heats and molar entropies of adsorption were calculated as a function of coverages and temperature. The values of isosteric heats of adsorption were found to be higher for active carbon supported metals, which may be due to the chemisorption of adsorbate molecules with metal sites present on the surface of active carbon. The extent of coordination of adsorbate molecules with metal sites is discussed on the basis of the acidic character of metal.     

Morphology and optical properties of liquid crystals embedded in polyester resin matrix

This paper reports on morphological, thermo-optical, and electro-optical results of UV-cured polyester resin film containing liquid-crystal nematic and cholesteric domains. Electro-optic measurements were performed in an applied d.c. electric field. The morphological structure of PDLC film is modified by the various methods of their preparation. Size-distribution curves drawn vs the duration of the initial cooling obtained for cholesteric liquid crystal domains are presented.     

Orientation of the diphenylene propane unit in stretched polycarbonate from two-dimensional magic-angle-spinning NMR

Two-dimensional magic-angle-spinning (2D-MAS) NMR has been used to measure the orientation parameter, P₂, of the diphenylene propane unit in bisphenol-A polycarbonate oriented by stretching to various extension ratios,, atT=295K andT= 403 K.P ₂ is proportional to the birefringencen, with a maximum birefringencen ₀= 0.189. There is some evidence that the order parameterP ₂ of the DPP units with respect to the chain axis deviates from unity.n ₀ is therefore expected to be different from the birefringence,n ₀ , of perfectly aligned chains of polycarbonate. The experimental results obtained forP ₂() are compared to those predicted by the aggregate model.     

Thermal and electrical studies of some polychelates

Polychelates of Mn(II), Fe(II), Co(II), Ni(II), and Cu(II) with 4,4′-dihydroxy-3,3′-diacetylbiphenyl-dithioxamide (DDBDO) have been prepared. Their structures were determined by visible reflectance spectroscopy and magnetic measurements in conjunction with thermogravimetric and IR measurements. Elemental analysis indicates a 1∶1 metal-ligand stoichiometry and the association of water molecules with the central metal. The decomposition temperature of the chelates is in the order Ni(II)>Fe(II)>Co(II)>Mn(II)>Cu(II). Thermal activation energies (E _a ), calculated with the help of Freeman-Carroll and Sharp-Wentworth methods, are in agreement with each other. The polychelates were found to be semiconductive, and the activation energy obtained from semiconducting behavior follows the order Co(II)>Ni(II)>Fe(II)>Cu(II)>Mn(II). The probable structure, such as six coordinated octahedral for Mn(II) and Fe(II) polychelates and four coordinated square planar for Co(II), Ni(II), and Cu(II) polychelates, have been suggested.     

Film formation with latex particles

The coalescence of latex particles is investigated through small-angle neutron scattering and electron microscopy. The particles are made of a soft polymeric core protected by a hydrophilic membrane, and they are dispersed in water. This dispersion is spread on a substrate, and water is removed to form a dry film. As the membranes of neighboring particles come into contact, they may break up to allow fusion of the particle cores. This is found to occur when the membranes are made of short-chain surfactant molecules; then all hydrophilic material is expelled to the film surface or to large isolated lumps. Alternatively, the membranes may remain until the film is completely dry; this is found to occur when they are made of hydrophilic polymers which are grafted onto the core. Hence, the fusion of particles is controlled by the connectivity of membranes.This work used the neutron beams of ILL in Grenoble and LLB in Saclay     

Numerical analysis of density gradient centrifugation profiles from eukaryotic DNA

A numerical method for the deconvolution of superimposed Gaussian distributions with a unique solution has been proposed by Medgyessy [10]. We have tested the usefulness of this method for the analysis of density gradient centrifugation profiles from eukaryotic DNA, which are normally composed from overlapping Gaussian distributed profiles of several subcomponents with different mean buoyant densities. From the analysis of human DNA and from model calculations we conclude that major subcomponents can be identified by this method, if they differ in their buoyant density by approximatly 0.005 g/ml. Minor components can only be identified if the total DNA has been fractionated according to buoyant density and the analysis is performed on the density profiles of the subfractions. This procedure represents a quick method to determine a reliable minimum number of subcomponents of DNA.This paper was presented at the VI. Symposium on Analytical Ultracentrifugation, Marburg, FRG, February 16–17, 1989.     

Studies of thermally stimulated current in polypropylene/calcium carbonate/surfactant systems

Thermally stimulated polarization (TSP) and depolarization (TSD) experiments have been performed with two grades of polypropylene and some respective CaCO₃-filled composites containing small amounts of nonionic surfactant (0–2 wt%). The effects of electrode blocking, electrode materials on the thermally stimulated currents, and reproducibility of the measurements have been studied. The effect of water vapor adsorbed from the ambient air on the AC dielectric properties and on the thermally stimulated polarization behavior has been determined.The addition of either CaCO₃ or surfactant to PP decreases the intensity of the _c depolarization current peak in the pre-melting region, while the presence of both components increases the current. Partial discharges are present in poly propylene/CaCO₃ composites under high voltages if neither water vapor nor a coherent surfactant layer is present at the matrix/filler interface.A short literature survey is presented on the TSC studies of polyolefins and their composites, and various mechanisms responsible for the observed changes are discussed, including interfacial polarization, trap redistribution through nucleation, and oriented adsorption.     

X-linked ultra high strength polyethylene fibres

The present work was aimed to improve further upon the mechanical properties of gel spun polyethylene fibres of ultrahigh modulus and tenacity. Cross-links were introduced by electron irradiation of the gelsbefore drawing. Under the present circumstances this resulted in much more favourable creep properties, of the fibres and tapes and also to retention of much of their strength after holding at 200 °C, without, however, significantly affecting drawability and the resulting high modulus and strength.